Search Documents

By Bill Loviza, Jimmy Sanders

This report is not everything we would like it to be. Access to information concerning unresolved legal actions is a sensitive matter. Obtaining the information presented in this report was a challenge alone. The Tennessee Department of Commerce and Insurance, Division of Fire Prevention, the firms and individuals that elected to share information did so with various assurances of nondisclosure, confidentiality or anonymity. All those providing information did so with the expectation that the industry and ultimately the public would benefit from this effort. We offer special thanks to Assistant Commissioner, Fire Prevention, Emmett Turner, recently retired Director, Bomb and Arson, Dick Gardner and Director, Codes Enforcement, Randy Safer for support that made this endeavor possible. We make no claim with regard to being a scientific study. We did the best we could with available information. Our task was one of assembly, sorting and reporting. Where collateral information was available we used it.

Jan 1, 2004

By José Ramiro Esteves Ramos

Características microestruturais são determinantes para as propriedades não ôhmicas de materiais varistores, uma vez que elas se relacionam com o coeficiente de não linearidade das curvas U x I, com a capacidade de absorção de energia, e com o seu grau de confiabilidade. O presente trabalho tem por objetivo a análise composicional e microestrutural de um material varistor comercial a base de ZnO dopado com diversos óxidos, além de comparar a eficiência dos ataques químico e térmico para a visualização das imagens em MEV. Os resultados obtidos condizem com a literatura onde foi observada a predominância de grãos majoritariamente compostos por ZnO com a presença de segregações constituídas de diversos elementos e concentradas nos contornos de grão. Quanto aos ataques, foi notável uma melhor qualidade das imagens quando se adotou o ataque térmico do ponto de vista da visualização dos contornos de grão. O ataque químico, por sua vez, demonstrou ser mais eficiente na elucidação das fases segregadas e na revelação da porosidade do material varistor.

Aug 17, 2017

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

A study was conducted to examine the potential of diesel emissions control strategies based on retrofitting existing power packages with exhaust aftertreatment devices and repowering with advanced power packages. The retrofit systems, a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF), were evaluated individually using a US EPA tier 2 (ter 2) engine operated under four steady-state conditions and one transient cycle. The DOC effectively curtailed emissions of CO, and to some extent organic carbon (OC), elemental carbon (EC), and aerosol number concentration. The DPF system offered substantially higher reductions in OC and EC mass and aerosol number concentrations. Both, the DOC and DPF achieved reductions in the aforementioned emissions without adversely affecting emissions of NO2 and nano-sized aerosols. The strategy of repowering with an advanced system was examined using a US EPA tier 4 final (tier 4f) engine equipped with a cooled exhaust gas recirculation system and diesel exhaust fluid-based selective catalytic reduction system, but not with a DPF system. The tier 4f engine contributed substantially less than the tier 2 engine to the EC and OC mass, aerosol number, and CO, NO, and NO2 concentrations. The tier 4f engine was very effective in reducing aerosol mass, NO, and NO2 concentrations, but it was not equally effective in reducing aerosol number concentrations. The implementation of viable exhaust after treatment systems and advanced diesel power packages could be instrumental to the underground mining industry to secure a clean, economical, and dependable source of power for mobile equipment.

By David S. Robertson

"IntroductionCanada has been one of the world's leading producers of uranium since atomic energy first became of practical importance in 1942. Indeed, prior to this time, between 1933 and 1940, Canada produced significant amounts of pitchblende, as a source of radium, from the Eldorado Mine at Great Bear Lake*.Uranium was first reported in Canada, however, in the middle of the 19th Century in the vicinity of Theano Point on Lake Superior north of Sault Ste. Marie. In the early 1900s, uranium-bearing minerals were reported in Quebec north of the St. Lawrence River and in pegmatites in Quebec and eastern Ontario. In 1930, G.A. LaBine and E.C. St. Paul visited an occurrence of cobalt reported by the Geological Survey of Canada in 1900, and brought the Eldorado Mine into production in 1933, as noted above, producing, in the main, silver and pitchblende.In 1942, developments in atomic energy were such that the Government of Canada, at the behest of Great Britain and the United States, requested that Eldorado, which had been closed in 1940, be re-opened to produce uranium for the Manhattan Project. In September, 1943, all discoveries of radioactive minerals were reserved to the Crown and their staking by private interests was banned. In January, 1944, the government nationalized Eldorado and formed a Crown corporation, the present Eldorado Nuclear Limited, to take over the assets. That year marked the formal beginning of uranium exploration in Canada.The Period 1944 to 1948In 1944, the Crown Corporation and the Geological Survey of Canada began exploring for uranium deposits, largely in the areas of Great Bear Lake and Lake Athabasca. In that year, A. W. Joliffe of the Survey visited properties on the north shore of Lake Athabasca near Beaverlodge Lake and recommended that Eldorado acquire claims in the area. In 1946, P. St. Louis and E. Laurum, prospectors working for Eldorado, found the pitchblende veinlets that led to the Ace Mine. Shaft sinking began in 1951, and production, through a carbonate leach plant, began in 1953.Continuing drilling on the Eldorado claims led to the Verna ore bodies, some 6,000 feet northeast of Ace, on which shaft sinking started in 1954."

Jan 1, 1986

By Madhu. P, Srinivas. K

Measurement of thermal properties like thermal conductivity, thermal resistivity, heat capacity and thermal diffusivity for materials, it plays a crucial role in a wide range of various civil and electrical engineering projects, and many field applications like building’s basement, power generation, underneath soil heating, wastes from nuclear as well as thermal plants, and buried cables. Thermal conductivity of soil depends upon various geotechnical parameters such as type of soil, moisture content, particle size distribution, density, and compaction characteristics. Earlier studies, the measurement of thermal conductivity of soil by incorporating the heat source methods. Thereby expensive and time taken to conduct in laboratory as well as field measurements. The thermal conductivity is determined by fabricated probe and used in this work. Fabricated probe was calibrated with glycerin. The thermal conductivity of the soil increases as the water content and density increase because these factors are majorly influencing and water has a higher thermal conductivity than soil minerals, and grain to grain contact increases as density increases. therefore, Thermal conductivity is higher in coarser soils than in finer soils. The details regarding of this work as explained in this paper.

Sep 1, 2022

By John L. H. Patterson

Handheld XRF has become the favorite way of measuring the content and identity of alloys in the field. This is because of the very portable nature of the instrumentation and its simple operation. However, these analyzers have been unable to determine the concentration of the light elements like Mg and Si due to the very low energy of the x-rays produced by these elements. In the past accessories such as vacuum and He flush have given some analyzers the ability to determine these light elements with modest detection limits. The introduction of the Silicon Drift Detector (SDD) into this class of instrumentation has added a new level of analysis capability to portable XRF instrumentation. X-ray fluorescence is achieved by exciting a sample with a beam of x-rays, which in recent portable equipment are generated by a small tube. This results in the emission of characteristic x-rays from the sample under test. By measuring the energy of each x-ray it is possible to determine what element generated it. By counting the number of x-rays at each energy it is possible to determine the concentration of each element. The detection limit for each element is dependent upon the number of x-rays which reach the detector. As the number of x-rays increases the detection limit will improve. One of the major factors in an x-ray reaching the detector is the energy of the x-ray. As the energy of an x-ray increases the probability of that x-ray reaching the detector increases. The energy of an x-ray is inversely proportional to the atomic number (AN) of the element generating the x-ray. For example, an iron x-ray (AN=26) is 6.40 keV while an aluminum x-ray (AN=13) is 1.49 keV. As the energy decreases, the detection of the x-ray becomes less and less probable because the x-ray may be absorbed by the windows which are part of the instrument and detector or the air in the path between the sample and detector. In SiPIN based portable XRF analyzers, the lowest element which is detected with acceptable detection limits is normally considered to be Ti (AN=22). The detection limits for 60 second measurements on typical SiPIN XRF analyzer are given in Table I. Thus, portable analyzers have not been useful for measurement of aluminum and titanium alloys as major components of these alloys are Mg (AN=12), Al (AN=13) and Si (AN=14).

Jan 1, 2009

By R. C. Buehl

A pyrometallurgical process for recovering manganese from open-hearth furnace slags or low-grade manganiferous iron ores is described. The slag or ore is smelted in a blast furnace to produce spiegeleisen; the speigeleisen is then blown with air in a basic converter to give an oxide slag. This slag product contains 60 to 75 percent manganous oxide and may be considered a synthetic manganese ore. In the smelting operations coke rates for five test periods ranged from 3,255 to 4,130 lb per ton of spiegeleisen. The recovery of manganese in the spiegeleisen varied from 60 to 76 percent. Recovery increased to 83 percent when the open-hearth slag feed to the blast furnace was diluted with a high-? grade iron ore sinter to facilitate smelting. In blowing the spiegeleisen a cyclic procedure was developed that gave nearly 90 percent recovery of manganese in the slag product (synthetic ore) yet prevented excessive contamination of the slag by phosphorus and iron. The overall recovery of manganese was about 75 percent when iron ore sinter was used with the open-hearth slag in the smelting step. The metal remaining after oxidizing the manganese from the spiegeleisen contained approximately 3.5 percent phosphorus. It was refined in a basic converter by blowing with air in the presence of lime" A high--grade iron and a basic phosphate slag were produced.

Jan 1, 1965

By Zoë Mullard

Just as a mine has a lifecycle, employees working within the mining sector also make several transitions throughout their career, from initial recruitment to retirement from the industry. Throughout the employment lifecycle, employees bring skills and knowledge that significantly contribute to the global economy. These skills are developed through education, professional training, coaching and through hands-on experience. Despite the current economic conditions and the demand for minerals, the mining industry is facing a substantial skills shortage due to the disparity between the number of new workers entering the mining industry and a largely ?graying workforce?. Although educational programs continue to evolve to attract people with a wide range of skills, the diversity of jobs and the strains of working in remote mining operations continue to present challenges for recruitment and retention of employees. This gap also presents challenges around knowledge transfer at a corporate and mine-site level; employers will require cultural and techno-sociological approaches to ease through these transitions. At the same time, there has been an explosion of social media tools that facilitate information sharing, cross-organizational collaboration, distance learning and knowledge capture. These tools have become increasingly popular in the last few years and their applications vary widely. The mining sector has started to adopt these tools for a number of purposes, including opportunities to harness social media to enhance human resources interactions, outreach and oversight. This paper will outline several case studies that explore leading practices for how the application of new media can assist organizations and individuals as they progress through their careers. This paper will illustrate how new social media communication technologies can be used to increase employee engagement and build organizational capacity in the mining industry. The paper will also include strategies for how to implement social media to enhance human resources applications and will cover ideas for monitoring and evaluation.

Aug 1, 2013

By Alan E. Gallie

One of the requirements for the successful waging of war is an unlimited supply of iron ore. In the spring of 1941 the demand for iron ore was expected to exceed the supply. This was particularly so in the case of high-grade lump iron ore, essential to the open-hearth process of making steel. The bulk of Canada's iron ore was imported from the United States. At this time, Canada was making every effort to conserve United States funds for more vital purchases. For these reasons, the development of Canadian iron ore resources became of prime importance. Several companies undertook investigations and one of these examined the old Josephine deposit. Location The Josephine property is in the district of Algoma, in the Michipicoten area of the Sault Ste. Marie mining division of Ontario. It is 120 miles north of Sault Ste. Marie and 20 rail-miles east of Michipicoten harbour, on lake Superior (see Figure 1). Transportation in the area is furnished by the Algoma Central and Hudson Bay railway. The Michipicoten branch of this line passes within a mile of the Josephine mine. Michipicoten harbour provides a port through which iron ore is currently shipped. Power in the area is supplied by the Great Lakes Power Company, with generating plants on Michipicoten river, on Montreal river, and on St. Mary's river at Sault Ste. Marie. A series of transmission lines cover the district and one of these is connected to the Josephine mine by a 3 ½-mile branch line. History The Josephine property was staked by Alois Goetz in 1899. Before the claims could be recorded, the township in which they are located was given to the Algoma Central & Hudson Bay railway as part of a land grant. As a result, the ownership remained in dispute until August 24th, 1906, when a settlement was arbitrated by the Honourable Frank Cochrane. His ruling is interesting and is quoted in part.

Jan 1, 1947

The engineering company's participation in quality assurance in the mining industry is twofold. Not only must it have such a program to ensure the necessary high standards for its own design and construction of a minerals processing plant, but it is also responsible as the "engineer" for both the selection and the quality of purchased equipment which goes into that plant. It is in this latter role that the engineer finds the most difficulty, or controversy, since while it is relatively easy to control his own performance, this is not ncessarily so when dealing with companies, all with their own ideas or standards. The engineer has perhaps rather reluctantly become more involved with the quality assurance of purchased equipment. This is because he has been used to writing performance type specifications and expecting the equipment manufacturer to provide the degree of quality, and control of that quality, for the product to meet the specified operating conditions. However, this has sometimes placed the manufacturer in a difficult position since to remain competitive in today's market conditions, he cannot always insist on product improvements or options which may in the long run be vital to reliable operation of the equipment.

Jan 1, 1982

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By J. L. Workman

The Putnam Coal Mine, at design capacity, will be the third largest underground bituminous coal mine in the world and will feature the world's longest single flight belt conveyor. Construction is now in process; initial mining will commence in early 1969 and design capacity will be reached in 1971. The Putman Coal Mine reserves are located in south-central West Virginia and contain approximately 27,000 acres of prime Pittsburgh No. 8 coal; reserves are sufficient to support a 3.5 million tpy operation for over 30 years. The mine portal area is located some six miles inland from the Kanawha River. The river loading facility is located approximately 156 miles by way of river from the market.

Jan 1, 1969

By N. I. Fisher, J. Shepherd

A rapid method of determining natural fracture trends in collieries has been developed. The method will yield information that is precise enough to permit fracture domain boundaries to be delineated in a coal seam. Instead of a survey of cleat trends in a colliery taking several man-weeks or even man-months, a reconnaissance survey can be carried out in only a few man-days. At each of a sequence of sampling sites along a traverse, five measurements of trend are recorded for each set of fracture directions. A sequential plot of the medians of each fracture set is then made manually underground or by a computer in the mine office. Changes in fracture pattern can be detected easily in colliery development work if a geologist visits advancing faces regularly, and forecasts can be made about the likelihood of forthcoming faults and dykes. A full description of this method is given in Shepherd and Fisher (1981). The concept of mapping fractures rapidly in a colliery is based on using a geological traverse (Compton, 1962), along which observations can be made at chosen, regular intervals. The technique has been widely used for surface mapping across outcrops and in follow-up work in photogeological studies (Hepworth and Kennerley, 1970). In these cases, the geologist surveys the traverse line as mapping proceeds. In a colliery, however, ready-made traverse lines already exist in panels and along main roadways, often in several directions. It is thus possible to traverse a colliery in different directions and record the fracture trends at intervals, generating a reconnaissance fracture map. This can also be done on a continuing basis as mine development takes place. Generally, a sampling traverse should be longer than 0.5 km with sampling sites at relatively close-spaced intervals along the traverse. For example, in room-and-pillar mines pillars are commonly formed on 40-m centers and the sampling sites can then be arranged at 20-m intervals [(Fig. 1)]. The sites might have to be closer together for mines known to have bad mining conditions. The predominant fracture trend is normally the face cleat and the subordinate trend is the butt cleat (McCulloch et al.. 1974). Various changes can occur in the cleat or joint pattern: the face and butt sets may disappear or an entirely new set or sets may appear. Therefore, it is best to record all prominent fracture sets. Sometimes there is only one; in other cases there may be as many as three or more. An odd number of measurements of each fracture set are made (generally five or more) to enable the median value to be determined easily. The median value can be plotted underground using graph paper or a computer plot can be made in the laboratory or mine office [(Fig. 2)]. The sequential linked median (SLIME) plot draws the median trend for each sampling site as a unit line segment. The segments from successive sampling sites can be connected together to form a long chain [(Fig. 2A)]. The needle plot, on the other hand, draws a straight line to represent the traverse and then plots out the median trend for each sampling site [(Fig. 2B)]. The SLIME plot is better for visual display, as it highlights small irregularities and gross changes in trend. However, some work is required to relate the individual segments to their site location along a traverse. In this respect, the needle plot is more convenient because each segment -can be plotted-at a point corresponding to its location. Also, there is precise match-up if needle plots of face and butt cleat are compared. A description and listing of the SLIME program is given by White et al. (1981). An example of the use of this method is given for Wallsend Borehole colliery in New South Wales (Australia) [(Fig. 2)], where domains II and IV are associated with mining hazards. Domain II is coincident with a normal fault of 2.6-m throw, and domain IV with a basic dyke 12 m thick. These hazards were approached driving in a southwesterly direction, and a pronounced change in trend of the cleat to a northwesterly direction occurred at a distance of approximately 45 m from each one. The northwestern joint trend is parallel to that of the dyke and fault, and it occurs at a higher frequency close to these structures. The association of a particular joint set with faults has been found elsewhere (Shepherd and Creasey, 1979). The two minor cleat direction changes within domain V are narrow joint zones that are less than 5 m wide. The fracture trends derived from a SLIME traverse can be verified by collecting larger quantities of data at selected sites, as shown in the balloon density (rose) plots depicted in [Fig. 2C]. We are grateful for the financial support provided by Thiess Bros. Pty. Ltd. and the National Energy Research, Development, and Demonstration Program administered by the Commonwealth Department of National Development and Energy. R.W. Miller Holdings Ltd. and Thiess Bros. Pty. Ltd. are thanked for their permission to publish data from their collieries.

Jan 1, 1982

By Warren Smith

IT has been 5 years since the writer left the Philippine Islands and while in that country his chief work did not lie in this field, though he has visited all but one of the localities mentioned in this article. The principal field studies relating to oil were made by his colleague, Mr. Wallace E. Pratt. The writer's investigations dealt with the general stratigraphy and paleontology of the Philippines. With the exception of the investigations made by Mr. Pratt and the writer very little information on this subject is available. A number of geologists in the employ of large oil companies have visited the Islands from time to time but, following the general rule, the public has scarcely ever been permitted to learn anything of the results. The writer is indebted to the Bureau of Insular Affairs, Washington, for late information regarding recent legislation in the Islands relating to petroleum. All the known oil seeps, petroleum residues, such as ozocerite, and natural-gas emanations are associated with Tertiary sediments. The chief seeps and most promising prospects are located as follows: 1. Bondoc Peninsula (lower end), Tayabas Province, Southeast Luzon. 2. The west coast of the island of Cebú from Alegria north to, and perhaps beyond, Toledo. 3. Central Mindanao not far from Lake Lanao. 4. The ozocerite veins on the Island of Leyte in the northwestern part in the vicinity of the town of Villaba. 5. Natural gas from some deep wells in Tertiary shale formations on the eastern flank of the Cordillera and extending out under the plain on the island of Panay.

Jan 2, 1920

The panic bars (and associated linkage's and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on Self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and soma commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in 'Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By Y. Suzuki, J. Nagao, Y. Ueda, K. Shimokawa

"A Ti- Ni intermetallic compound could be formed rapidly from Ti and Ni powder compact with SHS process. Microgravity experiments using a drop shaft are carried out, This report shows the effect of microgravity or high gravity on formability of an intermetallic compound. It is concluded that the specimen forms a porous and nearly amorphous alloy by rapid cooling under microgravity but with rapid cooling under high gravity after microgravity, the specimen forms a uniform and dense structure with better crystallinity.IntroductionTi - Ni inter1etallic co1pounds have been produced and have beco1e si1ilar to the a1orphous and porous structure as a result of the SHS (Self Propagating High-te1perature Synthesis) process under 1icrogravity. SHS process is being applied to the synthesis of cera1ics and inter1etallic co1pounds (1). The technique is characterized by a large a1ount of heat being emitted within a very short ti1e interval as regards the sistering reaction. One SHS process, acco1panying 1elting by a reaction was observed, and that was due to the quick heating of a Ni-Ti co1pact containing 50 ato1ic percent of Ti under a low pressure (2-4). In this report, we have researched the use a drop shaft which is 1ore effective during a short ti1e under 1icrogravity and high-gravity, so as to obtain high dense speci1ens with the exception of porous specimens (5). Mechanical properties of each specimen were esti1ated from these 1icro-structures with a discussion about the effect of changing gravity regarding 1elting and solidification of the Ti-Ni intermetallic comounds."

Jan 1, 1996

By D. T. White

Pressure acid leaching of nickel laterite ores typically involves the production of an intermediate product that is releached and refined to pure nickel and cobalt products. BHP Billiton is developing the Ravensthorpe Nickel Project to produce up to 50,000 t/y of nickel via a mixed hydroxide intermediate, which will be refined at its Queensland Nickel (QNI) Yabulu Refinery near Townsville, Queensland. The hydroxide precipitation flowsheet has been adapted to process high magnesium ores through an atmospheric leach stage, eliminate iron(III) as jarosite and oxidise iron(II) during neutralisation. The neutralisation conditions are controlled to precipitate aluminium, chromium and silicon, and to ensure good solid-liquid separation. Soluble impurities such as magnesium are purged with the tailings stream and will be managed over the long term by crystallisation in evaporation ponds.

Jan 1, 2006

By Arthur V. Petty

The Bureau of Mines has researched the utilization of mining and pro-cessing wastes as raw materials for the production of glass-ceramic pipe. Characterization of various wastes as to occurrence and chemical composition is reported. A computer program was developed and used to identify waste materials and mixes that would result in glass melts from which glass-ceramics could be produced after cooling and subsequent heat treatments. The production of abrasion-resistant pipe from inexpensive and readily available domestic resources could offer an economical substitute for high-alloy steels containing the critical and strategic materials cobalt and chromium.

Jan 1, 1984

By M. Cuba

Geostatistical modelling aims at providing unbiased estimates of the grades of elements of economic interest in mining operations, and assessing the associated uncertainty in these resources and reserves. Conventional practice consists of using the data as error-free values and performing the typical steps of data analysis - domaining, semivariogram analysis, and estimation/simulation. However, in many mature deposits, information comes from different drilling campaigns that were sometimes completed decades ago, when little or no quality assurance and quality control (QA/AC) procedures were available. Although this legacy data may have significant sampling errors, it provides valuable information and should be combined with more recent data that has been subject to strict QA/QC procedures. In this paper we show that ignoring the errors associated with sample data considerably underestimates the uncertainty (and consequently the economic risk) associated with a mining project. We also provide a methodology to combine data with different sampling errors, thus preserving the relevant global and local statistics. The method consists of constructing consistent simulated sets of values at the sample locations, in order to reproduce the error of each drilling campaign and the spatial correlation of the grades. It is based on a Gibbs sampler, where at every sample location, the actual sample value (with error) is removed and a conditional distribution is calculated from simulated values at nearby sample locations. A value is drawn from that distribution and kept only if it satisfies some statistical requirements-specifically, the global relative error and local means and variances must be reproduced. All sample locations are visited and simulated sample values are generated iteratively, until the required statistics are satisfactorily attained over all sample locations. This generates one realization of possible sample values, respecting the fact that the actual samples are known to carry an error given by the global relative error. Multiple realizations of simulated sample values can be obtained by repeating the procedure. At the end of this procedure, at every sample location a set of simulated sample values is available that accounts for the imprecision of the information. Furthermore, within each realization, the simulated sample values are consistent with each other, reproducing the spatial continuity and local statistics. These simulated sets of sample values can then be used as input to conventional simulation on a full grid to assess the uncertainty in the final resources over large volumes. The methodology is presented and demonstrated using a synthetic data-set for clarity.

Jan 1, 2012

By The DY125-33(Leg 2) Science Parties, Chuanshun Li, Xuefa Shi, Bing Li

"The slow-spreading Mid-Atlantic Ridge (MAR), with a length of ~1.26*104km (Bird, 2003), is the longest mid-ocean ridge on this plant. Separated by the large, left-stepping Equatorial fracture zones, it then be divided into two approximately equal-length parts: Northern Mid-Atlantic Ridge (NMAR, ~6292km) with an average spreading rate of 24mm/yr, and Southern Mid-Atlantic Ridge (SMAR, ~6332km) of 33mm/yr (calculated from PB2002 model, Bird, 2003). Previous works (e.g. Fouquet 1997, Hannington et al., 2011) suggest that slow-spreading ridge could support hydrothermal activities and further favorable for the development of extensive seafloor massive sulfide deposits (SMS). Unlike the NMAR for which large part has been explored for SMS (Hannington et al., 2011; Beaulieu et al., 2015), the SMAR is amongst the least hydrothermal explored spreading ridges until now (Haase et al., 2005, Beaulieu et al., 2015), though both of them show significant similarities in terms of spreading rate, ridge morphology, segmentation, etc. (Macdonald et al., 2001, Sandwell et al., 2014, Tucholke et al., 2008).Before this work, several hydrothermal cruises had been to SMAR since British and German programs starting in 2002, some hydrothermal fields, along with systematic geophysical data, were newly investigated, and types of geologic setting that can host hydrothermal activity were firstly identified (e.g. German et al., 2008; Haase et al.,2005; Haase et al.,2009; Devey et al.,2010; Schmidt et al.,2011).."

Jan 1, 2017