Search Documents

By G. Deschenes, W. Yen

Ammonium thiosulphate is a non-cyanide lixiviant for gold leaching. The major problem is the high reagent consumption. A combination of 0.3M (NH4)2S2O3, 0.03M CuSO4, 3M NH3 was used to leach a copper-bearing gold ore at pH 10.2 for 24 hours. 30 kg/t of thiosulphate was consumed. Oxygen and copper species were found to be responsible for thiosulphate decomposition. The thiosulphate consumption could be reduced to around 17 kg/t by adding chelating agent, reducing copper sulphate concentration to 0.001 M and replacing CuSO4 by NiSO4. The increase of pulp density might reduce the thiosulphate consumption to around 17 kg/t. By regulating the oxygen supply, the thiosulphate consumption could be reduced to 10 kg/t.

Jan 1, 2002

By W Shamu

The mechanical properties of rock samples of identical lithologicalcomposition may vary significantly due to existence of materialdiscontinuities. Laboratory tests were carried out to determine the effect of material discontinuities on rock sample mechanical properties. The investigations consisted of detecting discontinuities, observing the failure mechanisms during uniaxial compressive strength tests, and analysing of the factors affecting the strength. A non-destructive testing method has been adopted to assist in thedetection of discontinuities. Laboratory testing proved that fractures leading to failures initiated on the detected discontinuities. The location, orientation, size, density and extent of the discontinuities contribute to different modes of failure and these affect the mechanical parameters of rock samples. Four modes of failure were distinguished for hard and brittlecylindrical rock samples. These modes were referred to as simple shear failure, multiple shear failure, multiple fracturing and vertical splitting. To evaluate the effect of discontinuities on mechanical parameters, the ratio of uniaxial compressive to tensile (Brazilian) strength was calculated and analysed for the different modes of failure. It was found that the value of the ratio depended on the mode of sample failure. The lowest value of the ratio was observed for shear mode of failure and the highest for vertical splitting mode of failure.

Jan 1, 1999

By W. S. Landers

Nine high-volatile bituminous Utah coals were carbonized singly and in blends with low-and medium-volatile bituminous coals. Of the 9 coals, 2 are in commercial use as the base coals in blends that produce industrially accept-able metallurgical coke, while 7 are regarded as weakly coking and are not used commercially in coking blends. The carbonization tests were made in a la-inch diameter, cylindrical retort, using 50-pound charges. Sunnyside coal blended with autogenous char generally produced larger and stronger coke than was yielded by straight Sunnyside coal. The volatile matter of the char and the concentration of the char in the blend appear to be important parameters influencing coke size and strength. A blend of 10 per-cent autogenous char of 7.2-percent volatile matter with Sunnyside coal yielded coke that was larger, stronger, and of higher apparent specific gravity than coke produced from an industrial coke oven blend consisting of 15 percent medium-volatile coal and 85 percent Sunnyside coal.

Jan 1, 1967

By F. A. Patty

[Health and safety hazards from contamination of the atmosphere in places frequented by persons depend to a considerable extent on whether the contaminating agent possesses sense-perceptive properties which will give warning of its presence before it '.an create harmful conditions. If a distinct and easily recognized warning is given in advance of harmful conditions, hazards ace mitigated, but if warning properties are inadequate or absent, the hazards are augmented. When evaluating the hazard presented by a potentially harmful substance used under conditions of possible escape into the air of places frequented by persons, it is therefore necessary to consider the warning properties of the substance along with ether pertinent information such as toxicity, inflammability, physical properties, and mode of use. If the contaminating agent inherently lacks warning; properties it may be possible to impart them by adding to the hazardous substance a small quantity of a relatively harmless substance which has a high warning intensity.]

Jan 1, 1929

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specificetiona that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the fusing temperature of ash and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of the coal, end that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3/ issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and "tipple" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered 1s a check on the practical results obtained in burning the coal.

Jan 1, 1953

By Avery H. Reed

ALABAMA'S mineral industry continued to expand. This was a record year for many commodities, with expansion in almost all industries. New records were established for the production of native asphalt, fixe clay, miscellaneous clay, kaolin, bentonite, lime, scrap mica, salt, sand and gravel, crushed limestone, crushed marble, and tale. Among the States, Alabama ranked second in the production of bauxite, third in the production of scrap mica and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacture of cement, and the production of crude petroleum, which together comprised 87 percent of the total value of production, compared with 86 percent in 1963. The iron ore industry continued to decline. This was the first year in which consumption of imported iron ore exceeded the consumption of domestic iron ore. The coal industry recovered from the slump caused by the abandonment of red iron ore mining by United States Steel Corp., and production expanded 17 percent, for the best year in coal mining since 1948. During the year, the one-billionth ton of coal was mined within the State.

Jan 1, 1965

By T. Arthur Palm, Stephen L. Bessinger

San Juan Coal Co. (SJCC) operates an underground coal mine near Farmington, NM. Continuous miners and a longwall produce 6.3 to 7.2 Mt/a (7 million to 8 million stpy). SJCC is owned and operated by BHP Billiton. The coal seam at SJCC has been shown to have a propensity for spontaneous combustion. As such, during the feasibility study for this project, it was elected to use a bleederless ventilation system on the longwall. Due to the combination of spontaneous combustion, methane liberation and, to a lesser extent, hydrogen sulfide, a typical wraparound ventilation system would not be appropriate. Three-entry gate roads are developed, and the longwall gob is sealed as mining progresses. SJCC uses a nitrogen injection system to continuously inertize the gob.

Jan 1, 2007

The mining licence for the Macraes gold mine places emphasis on the progressive rehabilitation of the land to a state compatible with the landscape and environment that existed prior to mining activities taking place. The shallow soils and hostility of the environment dictate that choices of plant species should focus on persistence rather than high productivity, choices that are made easier by observing the vegetation patterns that have developed naturally within the area, by recontouring landforms to integrate with the surrounding countryside and the use of appropriate plants and establishment techniques.

Jan 1, 1992

By Yunnen Chen

The test and use of natural materials as biosorbents for the removal of heavy metals from industrial wastewater is under constant development. In the present study, the biosorption capacity of waste microzyme was studied for cadmium The cadmium removal study has been carried out batchwise where the influence of physico-chemical key parameters such as pH value of solution, contacting time and initial cadmium ions concentration have been considered. The influence of metal ion concentration was evaluated and the results were fitted using adsorption isotherm models. The kinetic of cadmium biosorption was also investigated. The maximum percent removal was attained at the pH 7.0 after about 30 min. Waste microzyme was a potential biosorbent for the removal of Cd(II) from the effluent of electroplating industry.

Jan 1, 2009

Jan 1, 1966

By B. D. Paphane

Since the commissioning of the Tati Hydrometallurgical Demonstration Plant (HDP), which produces Ni and Cu cathodes as well as Co salt from sulphide concentrate employing Activox® technology for leaching, no kinetic data has been generated from the plant under normal operating conditions, from start-up to steady state. Therefore, this study seeks to determine the rate of reactions in the leaching circuit with a view to obtaining kinetic data for the system under the current operating conditions. Within the five-compartment autoclave operating at temperatures of 105°C to 110°C and 1100 kPa pressure, the extraction of Ni, Cu, and Co ions into solution is achieved through the oxidation of the sulphide concentrate using approximately 50 kg H2SO4 per ton, 10 kg NaCl per ton, and 1.21 kg O2 per kilogram of S2-. The autoclave reactions showed complex kinetics, with the reactions proceeding via some intermediate(s) before the formation of products. The results suggest that the reactions were dependent on the size of the metal ion of interest and the concentrations of the metal ions in the Tati concentrate as well as in chloride leaching. The order of the leaching rate constants was Fe2+ > Cu2+ > Ni2+ > Co2+ in all the compartments studied. The rates of leaching were also found to decrease as the concentrate moves from compartment 1 to compartment 4. For compartments 1 to 3, leaching was observed to be preceded by dilution of the repulp liquor (copper raffinate). The leaching rate for compartment 5 was slightly lower than that of compartment 1 but higher than the rates of compartments 2, 3, and 4 for all the metals studied. Keywords kinetics, hydrometallurgical plant, Activox

Jun 1, 2013

By Robert Hopler

Earthquakes, ground vibrations, seisms, or whatever you want to call the shaking of the earth, have been a fact of life throughout time. In spite of this, most people (except those unfortunate enough to live in seismicallyactive areas) have probably never felt this phenomenon, or if they have, only a very few times in their entire lifetime. However, when it does happen, nothing is more frightening than the sudden shaking of the earth beneath us - after all, we think of the ground we walk on as the unyielding, solid underpinning of our existence.

Jan 1, 2006

By Greg Parker

"As the Explosives Industry continues to evolve and condense, those involved, such as Blasters,Contractors, Distributors and Consultants, continue to be challenged by both internal and externalforces. Increased pressure by government agencies, higher safety standards, new levels of technology and mandatory certification programs, are forcing us to expand our awareness and increase our levels of efficiency. These higher standards require increased awareness. Increased awareness requires better training programs and better supervision with emphasis on production and the employee. This means the desire to improve must be instilled from the top down. this paper will explore the current impediments to this goal and discuss the possible solutions for achieving greater safety awareness, increased production and higher levels of personal achievement. Through the use of audio/visual aids, I will attempt to show the discrepancies as well as the solutions."

Jan 1, 1999

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By Didier Kasongo NYEMBWE

The paper circumscribes the base metal casting industry in Southern Africa. It essentially consists in the founding of copper and zinc alloys. The challenge related to the scarcity and the unaffordable quality patterns and dies faced by the industry is discussed. New manufacturing technologies for foundry tooling called Rapid Prototyping that can possibly be used to alleviate the above mentioned challenge are then presented and their benefits assessed.

Jan 1, 2007

By H. Savasci, G. Yarim, J. S. Chung

As part of ongoing deep-ocean mining research, hydraulic transport systems as well as status of deep-ocean mining systems are reviewed in the aspects of manganese nodules and crusts from 8006,000-m depth. The emphasis of the investigation of hydraulic transport is placed on the shape effect of particles on the pressure gradients and flowrates. Series of tests are being conducted to study the lift characteristics of a 2-phasevertically upward hydraulic transport of 2 types of small solid particles in a PVC pipe of 1-in (2.54 cm) diameter: irregular-shaped silica sands and equivalent spherical glass beads. Pressure drops and mass as well asvolumetric flow rates were measured by electromagnetic(EM) flowmeter and mass flowmeter. The particle sizes used are 8-10 mesh. The results in turbulent flow range of 101045Re show that pressure gradients or friction factors are smaller for the spherical beads than the sands. The larger the concentration of the particles are, the larger the pressure gradients become. The larger the particle concentration is, the less the effect of particle shape on pressure gradients becomes. The shape effect is greater for the minimum particle transport velocities than for the settling velocities.

Jan 1, 1999

By G. B. Amicucci

Golden Sunlight Mines Inc. operates an open-pit gold mine and cyanidation plant about 11km (7 miles) northeast of Whitehall, MT. Golden Sunlight is a subsidiary of Placer Dome US Inc. Mining is accomplished with conventional open pit drilling, blasting and hauling methods. The mining rate is about 102 kt/d (113,000 stpd). Gold occurs as fine-grained disseminations in a pipe-shaped breccia and in immediately adjacent country rock. The ore body is low grade, averaging 2 g/t (0.059 oz per st) of gold. The metallurgical plant uses conventional carbon-in-pulp (CIP) technology. Daily throughput averages 6.5 kt (7000 st). Recoveries are enhanced through a sand tailing retreatment facility while a preaeration process reduces operating costs. The low grade ore dictates that maximum mill throughput at the desired grind size be maintained. Therefore, in October 1988, an Armco Autometrics (now Denver Autometrics) particle size monitor (PSM) 400 was commissioned. The PSM 400 is an on-line instrument. It measures particle size and percent solids in a slurry stream. The PSM pulls its own sample, deareates the sample and passes it through diametrically opposed ultrasonic sensors. The unit uses ultrasonic sound to measure the deareated slurry stream's particle size and percent solids.

Jan 1, 1991

By C. H. Johnson

The Big Jim mine of the United Eastern Mining Co. is at Oatman, Mohave County, Ariz. Oatman is in the foothills on the western side of the Black Mountains, at an elevation of about 3,000 feet. It is on a paved highway about 30 miles west of Kingman, the principal distributing; center for mining supplies in the district, and 25 miles from Topock, en the Colorado River. Both latter towns are stations on the Santa Fe Railroad; Oatman has no roil connection. Mining conditions are typical of western Arizona; water is scarce, no mine timber is available locally, and the winters arc mild and the summers hot. The supply of a killed labor is usually adequate, but in 1933-34 it w not more than sufficient for the restricted operations. Wages have been $4.00 to $4.50 for miners. Electric power was supplied from Kingman and cost about 2.6 cents per kilowatt-hour.

Jan 1, 1935

The La Colosa, Colombia porphyry gold deposit is currently in the pre-feasibility stage. This large deposit has many types of gold mineralization: native gold, electrum, and tellurides. These variations in the gold mineralization lead to variability in the gold recovery. The final process flowsheet may include gravity concentration with cyanide leaching. Metallurgical testwork is utilized to identify the zones of ore that may be problematic to recover. To help select the samples that represent the fluctuating variability zones, geometallurgical models are constructed using mineralogy and geology data. These zones are then wireframed and compared to the geological and structural models for spatial correlation. Samples for the variability testwork will be selected from these different zones to identify and analyse the effect the different gold mineralization types have on the recovery. By using geometallurgy to aid in the sample selection for metallurgical testwork, the variability in the ore body can be understood and constrained to aid in process optimization.

Feb 27, 2013

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998