Search Documents

By R. C. Fernandes, F. L. Santos

Aluminum alloys in particular, have certain limitations when subjected to welding process. This is mainly present because aluminum alloys have high thermal conductivity, high contraction in solidification and high hydrogen solubility. Taking this into account, the FSW process has great potential for this application, since it is autogenous, held without metal melting and without the use of slags or shielding gases. From this concept, the aim of this study is to evaluate the joining of thin sheets of aluminum alloy 3105 H26 with 0.7 mm of thickness. To performing of the tests, some parameters were analyzed, such as: tool penetration in the sheets, attack angle, the type of welding tool and penetration control mode (position or force). The results indicated that the force control mode is most suitable for thin sheets, and the transient state at the beginning of welding was the most critical part to control the welding quality.

Jan 1, 2015

By Stanley P. Jacobsen

Samples of fine coal refuse were obtained from 11 coal preparation plants throughout the United States. These samples were characterized by ash analysis, particle size, and mineral composition. From the characterization, geographical locations, and the dewatering equipment being used by the plants, five sites were selected for obtaining bulk fine refuse samples. The selected coal preparation plants were using for final dewatering thickeners followed by: a vacuum disc filter, a filter press, a belt press filter, a centrifuge, and a settling pond. None were using thermal drying. The moisture content of the final cake varied from approximately 23% to 50% depending upon the feed material, flocculant addition, and the type of equipment. The filter press gave the lowest moisture content followed by a belt press and then either a centrifuge or vacuum filter. The centrifuge products were all dried to an approximate 5% moisture in a thermal dryer.

Jan 1, 1981

Strain-Hardening Exponent of Cross-Rolled Beryllium Sheet by S. R. Maloff, Vol. 215, No. 5, page 872, was omitted from Table of Contents for the October issue. Stabilization Phenomena in Beta Phase Au-Cd Alloys by Howard Birnbaum, Vol. 215, No. 5, page 786. The figure denoted Fig. 1 should be Fig. 3, Fig. 3 should be Fig. 4 and Fig. 4 should be Fig. 1. The captions are in the proper sequence. Activity of Carbon in Liquid Iron Alloys by Tasuku Fuwa and John Chipman, Vol. 215, No. 4, page 708. First equation, right hand column, page 710 should read

Jan 1, 1960

By H Mali, B Kain-Bückner

Different types of lump iron ore-bearing particles were investigated in terms of their raw material properties depending on their behaviour during reduction. To predict the reduction behaviour different types of lump iron ore and pellet brands were characterised by their mineral abundance, texture and pore size. The image processing software VisuMet was developed to semi-automate the evaluation of photomicrographs from polished sections of lumpy iron particles. The results were compared to the standard reducibility test after ISO 4695. The evaluation of lump iron ores is based on the simulation of the transformation of the different iron minerals due to their sequence of reducibility. The progress of the reduction front is simulated and the result is a degradation curve. Pellets were also investigated due to their different pore size distribution. The results indicate that the pore size influences the reducibility in addition to mineral abundance. The evaluation with VisuMet of the lump iron ore and pellet samples correlates with the reducibility provided by the ISO 4695 test. The determination of the mineral abundance by VisuMet is comparable to common point counting with a correlation coefficient of 99.67 per cent.CITATION:Kain-Bückner, B and Mali, H, 2017. VisuMet – analyses of lumpy iron carriers with image processing, in Proceedings Iron Ore 2017, pp 557–560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Roberto Chambi

El presente texto describe las experiencias relacionadas al desarrollo e implantación del Sistema deTopografía para la mina subterránea de produccción polimetálica Raura. Para ello, se desarrolla la importancia de la topografía en el diseño y los proyectos mineros a través de un sistema de cálculo y dibujo topográfico. Los principales objetivos del sistema son: la gestión de la base de datos topográficos de la mina, la sustitución de las operaciones matemáticas “manuales” y la eliminación de sus errores inherentes, así como realizar automáticamente los dibujos de labores mineras a partir de la data recolectada y procesada, tanto en cálculos como en dibujo. De forma que se genera información procesada a los software especializados en geología y planificación.

May 25, 1998

By I. E. Wahn, E. A. Boutin

"The Manibridge Mill is unique in its treatment of relatively high grade nickel-copper ore because in the mill design are included one 10' diam. x 10' Maxwell cell, and three 12' diam. x 12' tank cells. These large cells are used as rougher-scavenger cells. Three 8' diam. x 8' tank cells as well are used for cleaning and recleaning of the tank cell concentrate.Flexibility of flow is the main criterion in the tank cell circuit. Targets from these cells are a high grade nickel-copper product with a minimum of talcose gangue.The operation of the tank cells has been encouraging and they have performed well with both low and high grade heads, yielding a high grade concentrate product.Manibridge Tank CellsDescription:The tank cells at Manibridge consist of one 10' x 10' Maxwell cell, three 12' x 12' tank cells, and three 8' x 8' tank cells. The four large cells are currently being used as rougher scavenger cells. The three small cells are used as cleaner cells.Both sets of tank cells consist of Denver steel tank and Super Agitator Mechanisms with steel beam super-structures. The agitator mechanism has a totally enclosed ball bearing spindle housing with a cold rolled steel shaft, and a stanclard standpipe with adjustable collar.The air rings for the tanks were fabricated by Nelson Machinery. Both large and small cells have injection rings with equally spaced air holes in the bottom centre line of the ring.Air is supplied to the tank cells by a Dresser Clark low pressure air blower.The following is a table of pertinent data on the tank cells:"

Jan 1, 1974

By David Arana

The use of gas-water dispersion of a molten material flow onto a vibrating surface is developed as a process to minimize water pumping requirements, minimize the risks of explosions, and minimize the post solidification dewatering and fines handling equipment requirements. The process uses existing vibration transport technologies and common plant utilities. Plant trials using the smaller footprint and the progressive molten particle cooling time have yielded encouraging results. The results are analyzed and reported.

Jan 1, 2006

By R J. In, C Moore, P J. Moffitt, T Hansen

Telfer Gold Mine combines a world-class gold and copper resource and longevity of operation as a major gold and copper producer. Telfer Gold Mine has undergone a series of transformations since mining commenced as a high-grade narrow-vein oxide open pit operation in 1977. In 1986, the open pit operation converted from a narrow-vein, high-grade operation, to a low-grade high-volume oxide mining operation utilising dump leach processing technology. Mechanised underground mining of the high-grade narrow-veins commenced in 1990. Total recovered gold production between 1977 to 1999 has totalled 5.7 million ounces. The Telfer Extension Project consists of two pre-feasibility studies, the Surface Extension Project (SEP) and the I-Series Project (ISP). The combined studies represent one of the more significant resource evaluations undertaken in the gold industry in recent times. Geological activities for the SEP pre-feasibility study have included the drill definition of a large low-grade resource within an area of 25 km2 . The surface drilling program has completed 15 000 metres of HQ3 diamond drilling and over 30 000 metres of RC between last quarter of 1998 and late-1999. The ISP pre-feasibility study is currently evaluating the resource potential of both a high-grade low-volume and a lower grade bulk mining scenario, 800 m to 1200 m below the surface of Main Dome. 15 000 metres of underground diamond drilling have been completed between last quarter of 1998 and August 1999 as part of this study. Systems and cultures have been developed to maximise safety, monitor the quality assurance/quality control (QA/QC) on all aspects of the operation, and minimise impact on the environment. All data are stored in database systems, specifically designed for Telfer operations. 3D geostatistical resource estimation using ordinary kriging has been carried out for over 220 geological domains within the 25 km3 of mineralised system. Non-linear geostatistical techniques are being investigated as part of the pre-feasibility study.

Jan 1, 2000

By Harry E. Holzschuh

The two Agrico Chemical Company self unloading Phosphate Rock barges put into service in 1976 operate at over their design carrying capacity. Each barge now carries 26,000 short ton instead of the planned 25,000 short ton at 32 foot of draft. They are in service between Agrico's Tampa, Florida Terminal and the Donaldsonville, Louisiana Fertilizer Complex, moving a total of 2,500,000 short tons each year. This was the first use of the Parascrew design for a marine application. The barges, with their 3,000 STPH unloading and matching loading rate is the vital link in this total transportation and handling system. Rock is moved from the Pierce, Florida Mines through the Tampa Big Bend Terminal, across the Gulf of Mexico, and up the Mississippi to the Agrico Faustina Phosphoric Acid Plant 30 miles below Bacon Rouge, Louisiana. The trip from the terminal to the plant is 600 miles and the turnaround time is just about six days. Seven years operating experience has proved that the system works. Fittingly, the two barges are named the "Faustina" and the "Pierce". They have a beam of 85-feet and are 495 feet long. folded depth is 43 feet, with a ballasted light draft of 19 feet and a typical loaded draft of 32 feet. There are four separated holds with the machinery room located forward of 101 hold. Each hold is 51 feet wide at the coamings with an 18 foot straight section on the side, and a 24 foot long, 600 slope sheet for a 23 foot clear reclaim width at the bottom. The Parascrew in each of the holds is 37 feet long between the bearings and is supported on a 14 inch diameter hollow shaft. The screw pitch varies and the diameter of the flights step up from l'-9" diameter to 2'-6" diameter on the discharge end. By sloping the centerline, a minimum four inch bottom clearance is maintained across the hold. Some bending of the tube does take place.

Jan 1, 1983

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By Bruce B. Redpath, Doug Crice, Rob Huggins

Over the last decade, instrumentation has been developed that allows the application of seismic reflection methods to groundwater and engineering problems. At the Geological Survey of Canada, we have been developing and testing shallow reflection techniques for mapping the bedrock topography and structure within the overburden. We have attempted to develop methods which can be implemented with a minimum investment in equipment and computing capabilities. The data are recorded on a l&channel engineering seismograph, using a single high-frequency geophone per channel, and a hammer or in-hole shotgun (“Buffalo gun”) as the seismic source. Processing and display of the data can be accomplished on an Apple II+ or IIe microcomputer and an Epson wide-track dot-matrix printer.

Jan 1, 1991

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Major mechanical components in the hoist and mechanical drive train are considered. Design and specification criteria based on American standards and practices are developed as they apply to typical mine hoist arrangements.

Jan 1, 1988

By Joseph M. Locke

The discovery of this asphaltum was made by S. H. Gilson, of Salt Lake, and since then the material has borne the local name of Gilsonite. So far as I have been able to ascertain, however, the first published notice of this discovery was made by Prof. W. P. Blake in the Engineering arid Mining Journal, of December 26, 1885, where he names the new mineral Uintahite, from the place of its discovery, the Uintah Mountains in eastern Utah. The priority of publication and the geographical fitness of the name will probably secure its acceptance by mineralogists.* The following is Prof. Blake's article. In the month of September last, a sample of peculiar asphalt was received for examination, and recently when in Provo, Utah, I had the opportunity of seeing a considerable quantity brought in from the Uintah Mountains. It is obtained in masses several inches in diameter, and apparently free from mechanically disseminated impurities. It breaks with a conchoidal fracture, is very brittle, and is readily reduced to powder in a mortar. Hardness, 2 to 25. Gravity, 1.065 to 1.070. Color, black, brilliant, and lustrous; streak and powder, a rich brown. It is a non-conductor of electricity, and is electrically excited by friction.

Jan 1, 1888

By Nikolas Schmitz

For today’s construction industry, large-diameter piles are common practice, as they are more competitive than drilling a larger number of smaller piles. More and more piles are installed by drilling rigs, replacing the installation by hammer, vibrators or caisson. Equipment capabilities and technics with rotary drill rigs are highly developed, but very costly and time-consuming when it comes to rock drilling, large diameters and deep foundations. Pile top drill rigs (PBA), based on reverse circulation drilling (RCD) technology, overcome these challenges and are an efficient solution for large diameter drilling (0.6 m to 8.0 m/19.7 ft to 26.3 ft) and drilling depths of up to 500 m (1,640 ft.)in various geological conditions onshore and offshore. The paper will explain benefits of RCD technology and prove this with figures from the Mumbai Trans Harbour Link project.

Nov 1, 2022

Jan 1, 1968

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

Historically, as for most reagents used in flotation, the wide-spread use of dialkyl dithiophosphinates as collectors in practical applications has preceded a detailed scientific understanding of how they work. Dialkyl dithiophosphinates are a technologically and commercially important class of collectors used in the flotation processing of Cu-Au, complex polymetallic, and precious metal ores. Plant usage has demonstrated that dithiophosphinates exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive health, safety, and environmental (HSE) profile. Although dithiophosphinates received little attention in the past in the flotation research community, recently, there has been significant interest in this chemistry, and numerous studies have been conducted to understand the fundamental interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized and explained by drawing on concepts and insights from coordination chemistry. A comparison between the interactions with various minerals and metals of dithiophosphinate and dithiophosphate analogues brings out some of the subtleties that seemingly minor changes in collector chemistry can make. The critical overview and analysis given here is useful in identifying gaps in knowledge regarding this important class of compounds. This in turn can provide a basis for the design of studies to advance our understanding of dithiophosphinate flotation performance.

By Glen Frank, David R. Chapman

Determining the number of boulders and cobbles that will be encountered in the tunnel envelope is one of the most difficult problems confronting the geotechnical engineer in the design of tunnels in glacial terrain. This issue is very important to the contractor, both in determining what methods will be used to construct the facilities and the advance rate that can be achieved for the chosen construction methods. The cost of constructing tunnels by pressurized face tunneling techniques is very sensitive to accurate characterization of the very coarse fraction (large cobble and boulder sized clasts), and no standard method is current available for characterizing boulders and cobbles. Careful use of large diameter borings and the sampling and analytical techniques outlined in this paper can provide a means to answer this difficult question. By performing large diameter borings and carefully recording and sampling the cobbles and boulders encountered, an estimate for the amount of these materials present in the formations sampled can be provided. Using this method allows the designer to communicate the expected geologic conditions to the prospective bidders in a manner that is both definitive and defensible. This paper describes the method as it was used in conjunction with the design of a large diameter sewer tunnel in the Columbus, Ohio area.

Jan 1, 2005

By L. I. Gonzalez de Vallejo

SRC rockmass classification have been applied to 25 tunnels in Spain and Italy, for which it was found that much heavier supports than those estimated by the RMR index were required. SRC and RMR indices and other relevant geomechanical data were obtained during the site investigation and construction stages. Data corresponding to in situ stress measurements, analysis of tectonic structures, and instability problems arising during construction were used to asses the state of stress. The relationship between tunnel section convergence and the SRC and RMR indices was also analysed. Support measurements based on SRC and RMR classification were compared with those actually used during construction. These analyses indicate that for most of the tunnels examined, supports estimated using the SRC were much closer to those actually installed than those predicted by the RMR index. Bei der Verwendung des SRC-Systems zur Klassifizierung des Gesteins als Baugrund für 25 Tunnel in Spanien und Italien wurde festgestellt, dass viel schwerere Abstützungen benötigt wurden, als wenn die Beurteilung anhand des RMR-Systems angefertigt würde. Die Klassifizierung anhand des SRC- und des RMR-Systems, sowohl als auch andere wichtige geomechanische Daten wurden während des Ablaufs der Erkundungen und der Bauausführung gewonnen. Die Resultate der Messungen der Spannungen vor Ort, die Analyse der tektonischen Struktur und die Stabilitätsprobleme während der Bauausführung wurden dazu verwendet, um den im Felsgrund vorherrschenden Spannungszustand zu definieren. Das Verhältnis der Messungen der Tunnelkonvergenz zu dem SRC- und RMR-Index wurde auch analysiert. Die durch das SRC- und RMR-System vorhergesagte Grösse der Abstützung wurde mit der Grösse der Abstützungen verglichen, die am Bau letztlich verwandt wurden. Diese Vergleiche zeigen, dass für die meisten der studierten Tunnel die Vorhersage der Abstützungen, die anhand des SRC-Systems angefertigt wurden, viel näher der wirklich verwendeten waren als die Vorhersage anhand des RMR-Systems. SRC rockmass la classification ont été appliqué à 25 tunnels en Espagne et l'Italie, pour laquelle il a été trouvé que des appuis beaucoup plus lourds que ceux évalués par l'index RMR ont été exigés. SRC et des index RMR et d'autres données geomechanical appropriées ont été obtenu pendant l'enquête de site et les étapes(scènes) de construction. Les données correspondant aux mesures de stress(d'accent) in situ, l'analyse de structures tectoniques et des problèmes d'instabilité surgissant pendant la construction ont été utilisées aux ânes(culs) l'état de stress(d'accent). Le rapport entre la convergence de section de tunnel et le SRC et les index RMR a été aussi analysé. Les mesures d'appui basées sur SRC et la classification RMR ont été comparées avec ceux en réalité utilisés pendant la construction. Ces analyses indiquent que pour la plupart des tunnels examinés, les appuis évalués utilisant le SRC étaient beaucoup plus proches de ceux en réalité installés que ceux prévus par l'index RMR.

Jan 1, 2003

Jan 1, 1970

Industrial minerals by definition are minerals used as part of an industrial process and usually are one of a number of components, eg finely ground Limestone is an extender in the manufacture of paint. They are normally non-metallic and non-fuel, but like all generalisations there are a number of exceptions. Take rutile û a source of titanium, a metal and also the raw material in the manufacture of titanium dioxide pigment. Industrial minerals under this general definition include construction and agricultural minerals. They are included in the same grouping, principally because their sources are similar and in many cases the raw material, example limestone, can be multi-functional. Calcium carbonate raw materials such as limestone, are used in a wide range of applications from industry as an inert filler, to agriculture as a 'lime' source and to construction and as an important component in the manufacture of cement. As far as this paper is concerned I will avoid discussing the agricultural or construction applications, including burnt lime production.

Jan 1, 1985