Search Documents

By V. Ferrari

This report documents the three-phase program to design, fabricate, test, and demonstrate economical and practical methods of reducing noise levels on underground coal mining portal buses (mantrip vehicles). The noise-control treatments applied to a production-model portal bus were as follows: ? Wheel/rail vibrations were isolated from the vehicle frame by inserting elastomeric materials between suspension components. ? Vibration-induced noise was reduced by replacing all large sheet metal panels (except floor plates) with damped steel panels. ? Motor noise was reduced by tight-fitting covers made from damped steel and lined with sound-absorbing material, and by elastomeric motor mounts. ? The standard spur gears used in the traction drive system were replaced with helical gearsets. The program achieved the goal of reducing the average sound-level to below 85 dBA for typical operating conditions.

Jan 1, 1981

By C. M. F. Vieira

This work has as its objective to characterize ceramic bodies for vitrified tiles elaborated with the mixture of nepheline-syenite flux and kaolinitic clay. Formulations were prepared with 0, 30 and 50 wt.% of nepheline-syenite incorporated in a kaolinitic clay. To determine the physical and mechanical properties such as dry bulk density, linear shrinkage, water absorption and flexural rupture strength, specimens were prepared by 30 MPa uniaxial pressure-molding and then fired in a laboratory furnace at 1150oC. The microstructure of the fired ceramics was evaluated by scanning electron microscopy. The results indicated that the nepheline-syenite improved the evaluated properties of the clay and attended the specifications of vitrified ceramic tiles.

Jan 1, 2010

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By Steven R. Munts

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the South Providence Wilderness Study Area (WSA) in 1982. No mines are currently operating in the WSA, however, the Golden Gift Mine in the southeastern part of the WSA produced $6,800 1/ worth of gold and silver and five mines adjacent to the east boundary of the WSA had a total production of about $3,500,000 1/ in gold, silver, lead, and copper. There is no recorded placer gold production. Over 350 lode and placer mining claims are in and immediately adjacent to the WSA. Of these, 74 were actively held (1982) and at least one area, which is partly within the northeast portion of the WSA, was being actively explored by private industry in 1982. Adjacent to the southeastern border of the WSA the Big Horn Mine contains an estimated 200,000 tons of indicated and inferred marginal reserves averaging 0.25 oz/ton gold; and the Hidden Hill Mine has 550 tons of subeconomic resources averaging 0.60 oz/ton gold. An additional 11,000 tons of marginally economic gold-bearing dump reserves average 0.17 oz/ton gold at the Bighorn, Hidden Hill, and the Buena Vista Mines and the Midas Touch Prospect. Sample analyses indicate eight mines and prospects in, and five adjacent to the WSA may have additional gold-silver-lead-copper vein-type resources. Five of these prospect areas may have a disseminated gold resource and one may have gold resources in a skarn. One prospect may have a porphyry-type copper-molybdenum resource. Although gold placer claims were filed sporadically throughout the WSA, none appears to have placer gold resources. Likelihood for mining is greatest at the Big Horn Mine; if a mill is built there, it could process Big Horn Mine ore, ore from the Hidden Hill Mine, and gold-bearing dumps at the Big Horn, Hidden Hill, and Buena Vista Mines and the Midas Touch Prospect. All of these resources are adjacent to the WSA; however, their development would increase likelihood for development of resources in the WSA. Two major fault zones (the Hidden Hill, and the Big Horn) appear to have controlled the mineralization at many of the prospects and mines. All of the prospects or mines with vein-type occurrences and resources are on or adjacent to one of these fault zones. Veins throughout the eastern half of the WSA contain various amounts of gold, silver, and copper; only veins near the Big Horn Mine and in the northeastern corner of the WSA contain lead. Some veins are as thick as 6 ft, are traceable intermittently for over 2 mi along strike, are sporadically mineralized, are encased in prophylitic, argillic, and phyllic altered host rock, contain pyrite, chalcopyrite, galena, specularite, barite, or fluorite, and display multiple stages of quartz veining and (or) brecciation. Sample analyses at five prospects (map nos. 3, 18, 23, 24, and 31) indicate they may have disseminated gold resources. To date no oil or gas has been discovered within the WSA. However, some oil and gas leases are currently (August 1982) held within this study area.

Jan 1, 1984

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By R. L. Grayson

In 2010, MSHA began holding hearings on a new coal mine respirable dust rule, which proposes a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the ?hot spots? where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines? compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, seam height, and selected ?hot spot? counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications on the need for better dust control methods.

Jan 1, 2012

Thank you for this opportunity to address your conference on 'The role of coal in the New Zealand energy market'. New Zealand's energy market has, in common with much of New Zealand, undergone major change following the market reforms of the Labour Government. As far as the energy sector is concerned this change has been for the better, as it has created for the first time in a very long time a 'true economic market' for energy in New Zealand. This is in marked contrast to the previous regime where: ò Electricity was state operated, subsidised and cross subsidised. ò Oil was imported and subject to a raft of taxes and duties. ò Coal produced by state mines was priced by cabinet committee, based on other energy prices rather than on the costs of production and delivery of the energy product. Today, with the establishment of the SOE's we have a market of competitive supply, where the customer has the choice of energy with prices based on the true costs of production and delivery. This can only be good for the customer as the cost is now based on the real costs of production, not on political whim. So where does coal fit in this brave new world of free market energy supplies? Well, opportunity, they say, knocks but once.

Jan 1, 1990

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By H. S. Price

This report discusses the development of a mathematical model that describes the flow of methane only and methane and water in a coal bed during mining operations. Because of the complex geometry, boundary conditions and fluid properties, the model is based on a numerical solution to the equations describing flow. The goals for the development of this model and requirements to which it complies are for the most part expressly stated in Request for Proposal No. 50110752. In addition to the capabilities specified under the scope of work the model can handle an anisotropic porous medium and a source term has been added which will simulate, somewhat, the effects of desorption. This term will be pressure dependent. The effect of time on such a term is only taken care of in the change of pressure with time. This source term will have the dimensions of Mcf/day/Mcf pore volume. It will be a part of the input data to be supplied by the user and will be entered as a table of rates versus pressure. These models consider the fracture system as the main porosity. All computed results pertain to the fractures. The source term mentioned above represents the flow from the matrix porosity into the fracture. Such flow should be small compared with the flow between fractures since these models handle only one porosity structure system.

Jan 1, 2012

By T. Nishimura, H. Kiyama, K. Wakimoto

Discussion on the load bearing capacity of ground and the stability of tunnel is presented. We derive a simplified solution of a circular lined-tunnel in an elastic ground. The solution results in a better understanding of characteristic curves. Use of DEM allows us to consider effects of possible yield of the overstressed zone around the tunnel and inherent discontinuity of ground on the curves. Diskussion auf der Last Tragfähigkeit Bodens und die Stabilität des Tunnels wird dargestellt. Wir leiten eine vereinfachte Lösung eines kreisförmigen Ausbautunnels in einem elastischen Boden ab. Die Lösung ergibt ein besseres Verständnis der Kennlinien. Um Gebrauch DEM erlaubt uns, zu betrachten Effekte des möglichen Ergebnisses der überbetonten Zone den Tunnel und zugehörige Unstimmigkeit des Bodens auf den Kurven. La discussion sur la portance de charge de la terre et de la stabilité du tunnel est présentée. Nous dérivons une solution simplifiée d'un revêtement-tunnel circulaire dans une terre élastique. La solution a comme conséquence une meilleure compréhension des courbes caractéristiques. L'utilisation de DEM nous permet de considérer des effets du rendement possible de la zone surchargée autour du tunnel et de la discontinuité inhérente de la terre sur les courbes.

Jan 1, 2003

AustraliaÆs strong position as an aluminium producer and potential magnesium producer combined with rapid market growth in the automotive industry, proximity to Asia and other natural advantages points to considerable opportunity for downstream processing and manufacture with light metals in this country. Development of a vertically integrated light metals industry in Australia needs to be pursued with vigour, as does the continued development of global strategic alliances through the value adding chain.

Jan 1, 2000

Endless lines at service station gasoline pumps, limited travel at reduced speeds, thermostats set at an uncozy sixty-eight degrees in the dead of winter-these are but a few of the inconveniences and discomforts that awakened Americans to a realization that our domestic minerals resources, traditionally taken for granted, are not boundless. We begin to accept and practice principles of conservation, yet we are aware that this alone cannot appreciably forestall the inevitable depletion of our minerals, metals, and fossil fuels-resources critical to our Nation's economy. The key to warding off shortages is the development of technology that will insure a continuing, adequate supply of minerals and energy from reliable sources at the lowest possible costs to society and the environment. The mission of the Bureau of Mines is to develop this improved technology. Established in 1910, the Bureau of Mines of the Department of the Interior is the Federal Government's primary research arm in the minerals and fossil fuels fields. In addition to its research role, the Bureau keeps the Government informed of the Nation's mineral posture. The Bureau also seeks to stimulate private industry, through the awarding of grants and contracts, to produce minerals and fuels at a rate compatible with the country's increasing demands.

Jan 1, 1974

The beach sand industry is the only Australian mineral industry which, so far, has used electrostatic separation on a full commercial scale. The main application of the process is for the separation of rutile from zircon. Laboratory work has demonstrated that electrostatic methods are effective for ilmenite-monazite and cassiterite-zircon separations, thus facilitating the production of high grade monazite and cassiterite products from top-strip table concentrates, but the commercial application of these processeshas been rather limited so far. Overseas, electrostatic methods are becoming more widely used for the treatment of granular material which is not amenable to flotation. The use of electrostatic separation for the treatment of ores other than beach sands has been investigated in this laboratory 1, 2, 3, and two pilot separators were built during i953 to carry out field tests. Of these, the first was an inclined feed plate separator for the removal of silica from granular lime-sand in Western Australia, the second a conductance roll separator for the removal of diamonds from alluvial gravel in New South Wales. In both cases the whole of the ore passed through the separator, not a gravity concentrate only as in beach sand practice. The two types of separator mentioned are shown diagramatically in Figs. 1 and 2.

Jan 1, 1954

By Richard A. Cubeta

Precast concrete segments have been used in sanitary sewer tunnel design for decades. Federal mandates (reduction in heavy metals and I & I), and system design changes (increased retention times) and other factors have exacerbated corrosion problems. In an effort to combat the ever-growing effect of microbiologically induced corrosion, owners, engineers, and designers have been specifying thin-film lining systems to protect precast concrete segments. These systems have compatibility and installation issues. Chemical additives or calcareous aggregates have been utilized in precast concrete, but have only proven to retard the rate of corrosion and do not eradicate the problem. Solid cast polymer segments are stronger than precast concrete, do not require linings or coatings, are impervious to ground water infiltration, and, above all, are inherently corrosion resistant through and through.

Jan 1, 2008

By Russell Miller, Fun-Den Wang

High Pressure Water Jet Assisted Tunneling The high pressure water jet assisted tunneling project was conducted in a granite quarry near Skykomish, Washington, approximately 90 miles east of Seattle. A 7-ft diam tunnel boring machine was modified and equipped with high pressure water jets. The concept that tunneling rates can be improved by using high pressure water jets was validated, with an average increased advance rate of 50% to 60%. For some tests, the advance rate was more than doubled. A comprehensive economic analysis has shown that very significant savings are possible. At a 50% increase in advance rate, cost savings of 14% and 24% were projected for 10-ft and 20-ft diam tunnels respectively. These benefits were seen to be relatively insensitive to water jet equipment costs.

Jan 1, 1976

By Paul S. Goodman

Volume I This report presents the first national survey of miners' attitudes and opinions about their-work. The goal is to present attitudinal data that bears on coal production. Interviews were conducted in 26 mines with 2,000 miners. High levels of cooperation were exhibited by management, union and the employees. Data are presented about miners' attitudes about general aspects of their work such as pay, supervision, their jobs, etc. Another section of this report reviews opinions about specific aspects of work performance. Recommendations are presented.

Jan 1, 1985

By D. L. Murr, J. R. Jensen

Testing was conducted on a Minnesota Iron Ore concentrate with Cook Clay as a binder using compressive sheer mixing to enhance the performance of the agglomeration mechanism. The testing was conducted on a bench scale at the Midland Research Center the summer of 2004. Results of the test program will be presented that shows the impact of compressive sheer mixing had on the strength achieve in a green ball.

Jan 1, 2006

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By John D. Spencer

Projects aimed at achieving the least disturbance to the Nation's air, water, and land resources in the mining and utilization of coal continued to be a feature of the Bureau of Mines coal program. This reflects the current concern about damage inflicted on the environment by our growing and increasingly affluent society. Mine Health and Safety research, along with investigations related to all other aspects of coal extraction and use, also continued to be implemented and expanded.

Jan 1, 1970