Search Documents

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

By Rahul Singh, Sunil Kumar, Erich Dohm, Maoming Fan

The rapid increase of P2O5 use for food, biofuels, and LiFePO4 batteries etc. accelerates the depletion rate of phosphate reserves. In the phosphate industry, a significant amount of ultrafine phosphate has been discarded as slime tailing due to processing difficulties. The major problems associated with ultrafine particle flotation are low probability of bubble-particle collision and adhesion, and high probability of unwanted gangue particles entrainment. This paper investigates the enhanced ultrafine phosphate particle flotation probability by Eriez’ CavTube generated fine/ ultrafine bubbles and the improved flotation selectivity by wash water etc. Ultrafine phosphates with various gangue minerals of quartz/muscovite, calcite/dolomite, and iron/ silica were studied. Microscopic observations show that the entrained ultrafine gangue minerals can be minimized by using wash water in column flotation. A three-factor threelevel central composite experimental design was conducted for ultrafine phosphate flotation. For comparison, both benchtop mechanical cell and laboratory column flotation tests were performed at their optimal respective flotation conditions. Using Eriez CavTube column flotation technology for Industries Chimiques du Senegal (ICS) ultrafine slime tailings, a concentrate grade of 36.0% P2O5, was achieved at 89.4% P2O5 recovery. Improved flotation performance was achieved using column flotation as compared to benchtop mechanical cell flotation. The benefits of Eriez’ column flotation technology realized from this study include the high P2O5 grade and recovery.

Feb 1, 2024

By L. Bloomquist, C. Arnoldi

"This paper describes how Automated Mining Systems (AMS) is evolving the state-of the- art in guidance systems for autonomous underground vehicles. The techniques, tradeoffs, and lessons learned from these systems are described, including the safety regime that has been implemented.First generation autonomous guidance systems for underground vehicles relied on infrastructure for the vehicle to follow. However, there are additional costs associated with that approach.The current generation uses a pair of laser range finders as its only guidance sensors. This system uses a minimum of infrastructure, in the form of a redundant system of location referencing. Advanced steering and drive control algorithms are incorporated into this generation of system.The next generation of infrastructureless guidance systems will be based on a 3D vision sensor, which was originally developed for autonomous Mars rovers and is being adapted for underground mining use. Results of early underground field trials are presented, along with a description of this emerging technology."

Jan 1, 2004

By Jorge Chira

INGEMMET realizó el proyecto “Estudio de los Recursos Minerales del Perú” con el objetivo de identificar las áreas prospectivas para propiciar actividades de exploración minera por parte de la empresa privada. Entre las funciones ejecutadas está la “Prospección Geoquímica Regional de Sedimentos de Quebrada”, donde se ha recopilado 5,636 muestras de sedimentos de quebrada, las que fueron analizadas por Au y 32 elementos a fin de elaborar posteriormente el Atlas Geoquímico del Perú. En ese sentido, el presente texto señala el uso del software para el tratamiento estadístico de los resultados a través del soporte técnico de la empresa GEOSOFT. Dicho software genera una tecnología confiable así como lo versatilidad para el manejo e interpretación de diversos datos. También se desarrolló el programa OASIS – MONTAJ; módulo CHIMERA con el cual se pueden manejar en forma exacta una gran cantidad de información geoquímica empleando controles de estándares y duplicados.

Aug 25, 2002

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 km. Some 500 km south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 km. The Complex was emplaced at several centres along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite. Except in the lower units of the Ultramafic Series sulfide mineralisation is widespread. Pyrrhotite is the dominant sulfide with lesser chalcopyrite pentlandite and pyrite. Four significant zones of sulfide accumulation are recognised and discussed in some detail. Evidence suggests that the primary magma from which the Riwaka Complex was derived was sulfur deficient. It is concluded that the sulfur content of the Riwaka Complex was derived from assimilation of sulfur rich wall rocks during intrusive processes.

Jan 1, 1980

By K. P. Wang

The foundation of Japan's growing industrial and economic strength lies primarily in minerals, power, and technical know-how. Domestic raw material resources cannot supply domestic demand, and imports are indispensable. The Japanese are forced to acquire minerals and metals on a global basis, and their activities already have made an impact on international markets. A by-product of these efforts is the development and expansion of mines in many parts of the world to supply Japanese requirements. Japan now has a surplus capacity to produce finished products for consumption and export. Tradition-ally, domestic deficits in minerals have been met by importing crude materials. Because of the rising demand, however, the time has come when semi finished products as well as crude minerals are required. While the domestic market is the mainstay for Japan's industrial products, expanding export markets are essential for balancing trade and for providing economic prosperity and higher living standards for the Japanese people. Japan has a long history of mineral and industrial development, and the best in modern practices abroad has been adopted and modified for use under Japanese conditions of smaller enterprises, cheaper labor, and a more closely knit society. Generations of industrious workmen, technicians, and business-men have been trained in industrial occupations. Devastation of war temporarily slowed progress, but at the same time provided the opportunity for reconstruction, modernization, rationalization, and expansion. The Japanese excel in small and medium-sized operations, but they also have mastered large-scale production. Management is aggressive, practical, and strongly imbued with the concepts of effective utilization of resources. Integrated operations, diversification of facilities, intense competition among concerns in the domestic market, and close cooperation in foreign activities characterize Japanese industrial policies. Available capital has been utilized up to the limit for the establishment of mineral and other industrial facilities at home and abroad. Technology, machinery and equipment, and transport services have been exported along with venture capital, and funds have been advanced against future delivery of foreign raw materials. The Government has been restrained in regulatory functions and has provided technical services to private industry. Thus, Japan's technological foundations are secure, management practices are efficient, and government has stimulated production. The future outlook is bright for the continued rapid growth of mineral and other industries in Japan. Already supreme in Asia in per capita output and living standards, Japan steadily is gaining on the European countries. Steel production has overtaken the United Kingdom and is pressing the level in West Germany. Consumption of fuels and power is expanding at a rapid rate. Construction activities are booming. Japan has built up medium-sized non-ferrous industries. Its ability to produce the exotic metals needed in the nuclear space age is well established. Since Japan makes a great variety of mineral products, her overall posture in mineral extraction and processing is strong. Primarily as a result of intensive efforts in the mineral and other industrial fields, Japan is emerging in world markets as a serious competitor to all industrialized nations.

Jan 1, 1962

Despite modest improvements in the performance of domestic interest rates and gross national product,1 fixed investment in domestic producers' durable equipment continued to weaken during the second quarter of 1982 and declined at a 12.8 percent annual rate compared with the first quarter.2 Large declines occurred during the second quarter in expenditures on many of the major mineral-consuming industries such as aircraft, computers, agricultural and construction machinery and mining and oil field equipment. These data appear to be consistent with the low level of business investment plans for 1982 reported in the DOC's Bureau of Economic Analysis survey of expenditures on new plant and equipment.3 Domestic and foreign industrial production and mineral industry production activities continued to decline in the most recent period because of weak demand conditions (Tables 1 and 2). The U.S. mining production index declined 7.7 percent between April and June as compared with 1.2 percent for total U.S. industrial production (Table 1).

Jan 1, 1982

By D. Harrington

The experience of the past 2 years has demonstrated clearly that mine explosions with heavy loss of life can be prevented. The investigations of the Safety Division of the United States Bureau of Mines disclose that during the fiscal year 1934 there were only 28 deaths from mine explosions in the United States, and during the fiscal year 1935 there were 54 deaths, a very favorable reduction when compared with an average death toll of 265 from this cause during the 20-year period prior to 1929. Although the frequency of occurrence of explosions has not decreased greatly during the past 7 years, there has been a marked decrease in severity, indicating that the coal-mining industry is taking more effective precautions to prevent the spread of explosions. A number of large coal-producing States, which in past years have experienced numerous disastrous explosions, have been free from such disasters for continuous periods of as much as 5 years or even longer. A study of several hundred mine explosions occurring in the United States during the past 10 years or more indicates that the factors mainly responsible for these explosions are inadequate or defective ventilation and disregard of the hazards from explosive gas. Both of these factors are subject to control, and if controlled it is safe to say that deaths from explosions would be reduced to a negligible number as relatively few explosions are now initiated by dust.

Jan 1, 1936

By A. D. S. Gillies

Inertisation is used to enhance the safety of underground mine areas either to avoid the potential for a combustion event or to stabilize a situation after an ignition, fire or heating. The primary objective of a recently completed Australian Coal Association Research Program (ACARP) study was to review coal mine inertisation and in particular to focus on use of the Polish mine fire simulation software Ventgraph to gain better understanding of how various inertisation units interact with the complex ventilation behavior underground during a substantial fire. Critical aspects targeted for examination under the project grant included location of the unit for high priority fire positions, size of borehole or pipe range required, time required for inertisation output to interact with and extinguish a fire, effects of seam gases on fire behavior with inertisation present and main fan management. A major accomplishment of the project has been to take findings from the simulation exercises to develop inertisation related modifications to the Ventgraph fire simulation program in conjunction with the Polish program authors. Selected mines were ?evaluated or audited?as to the ability to deliver inert gases generated from GAG units to high priority underground fire locations .A coding system has been developed and many potential underground mine fire sources cannot be successfully inertized with the GAG docked at the current specified point; this is particularly so for fires in extended areas of workings or in panels. There is a limit to the ability of the GAG jet engine to deliver exhaust down smaller dimension borehole. There is a need to examine the use of the GAG for production or proactive uses in a wider application in Australian mines responding to recovering from mine fires, spontaneous combustion heating?s, elimination of the potential explosibility of newly sealed gobs or inert mines or mine sections on closure. Some of the current uses of low flow inertisation facilities could be more effectively undertaken with the GAG unit.

Jan 1, 2009

By John F. McCoy

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller Associates, Inc. (FMA) to develop guidelines for designing, constructing, stocking and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressurization Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

Keywords: Stellenbosch, university, teaching, research The pyrometallurgical activities at Stellenbosch University are reviewed in this paper. The history of the activities, both in teaching and research, is outlined, as well as some of the perceived research opportunities that the University of Stellenbosch is currently focusing on. The course content, as well as its relationship to other courses in the curriculum, is discussed and the interfaces between the courses are explained to present a holistic picture of the education an engineering graduate receives in process pyrometallurgy.

Jan 1, 2006

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to develop a mathematical model of cable bolt support systems. Part 1 described laboratory studies of the support properties of conventional steel cable bolts. Part 2 describes the strength characteristics of conventional cables with steel buttons, single and double birdcage cables, and epoxy-coated cables.

Jan 1, 1991

By J. M. Dempsey, R. A. Litle

Asarco Incorporated’s Omaha, Nebraska refinery site and the City of Omaha’s downtown redevelopment projects are the perfect example of the marriage of the Brownfield and Sustainable Development strategies. Nebraska’s largest voluntary site remediation project created a focus point for redevelopment and has spurred over $1 billion in economic investment within a 1-mile radius of the site. Asarco was faced with options of very expensive and uncertain facility upgrades or a shutdown. Local leaders, Asarco, and regulators worked together to convert a controversial and complex site to a park-like redevelopment area with numerous long-term benefits to the City and the environment.

Jan 1, 2004

The quantity, quality and detail of project information increases as project development moves from initial scoping level studies, to pre-feasibility and option studies, then definitive feasibility study and basic engineering stages. Data accumulates from metallurgical and vendor testing from various ore types and composites carried out to assess physical characteristics and processing responses of the ore. Over-simplification or assumptions about the orebody for flow sheet development can result in using æaverageÆ information for design. Use of averages of data can have adverse implications on sizing of plant and equipment and consequently on definitive study cost estimates and detailed engineering. In practice, the treatment plant workforce is faced with managing a non-homogeneous or non-average orebody in a variable operating environment that is not always predictable. This paper presents views on how to use the data generated from testwork in project development and for process and plant design. Examples of process design risk or operating risk are presented. Although this topic is applicable to the broad range of process design decision making in the minerals industry, this discussion references comminution, flotation and extraction processes for gold and base metal ores.

Jan 1, 2004

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

The Effect of Mineral Liberation on the Floatabilities of Pyrite, Arsenopyrite and Arsenian Pyrite for Carlin Trend Ores

Sep 13, 2010

By Xingjian Gao

The mechanical properties of a low carbon low alloy steel in the austenite and _-ferrite regions have been examined by thermal-tensile tests using a Gleeble-1500D system at temperatures in the range 600oC to 1300oC and at a strain rate of 10-3/s; these being the conditions that apply to the unbending operation during the continuous casting of steel. The yield strength and tensile strength of steel decreased with increasing test temperature and the embrittlement zone occurred in the temperature range 800oC to 970oC. In the embrittlement zone, the fracture surfaces and microstructures of the tensile specimens were examined by scanning electron microscope. The results showed that the cause of the embrittlement at 950oC in which the minimum %R of A was around 36% is the second phase particles precipitated along the _ grain boundary during deformation leading to inter-granular brittle fracture.

Jan 1, 2010

By Franklin D. Cooper

The value of nonfuel raw mineral production in the United States for 1977 increased over that of 1976 by 5%, from $16.7 billion to $17.5 billion. Metals declined by 5% from $6.1 billion to $5.8 billion, chiefly because of strikes in the iron ore industry and a depressed copper market. Subsidization of mining industries in some foreign countries accounted in part for the excess of copper and some other metals on world markets. Weak metal markets and continued slowdowns in the world economy were the main reasons of the virtual absence of new mine projects. Increasing domestic governmental involvement affecting mineral industry activities, such as pricing controls, public land withdrawals, and the Surface Mining Control and Reclamation Act, effective August 3, continued to be controversial and to be criticized by various segments of the industry.

Jan 1, 1980