Search Documents

By J. A. Every-Brown

Case studies are presented of three derelict sites in Kent and Essex that provide a good cross-section of opportunities for second-generation commercial uses of former chalk, limestone, clay and gravel workings. A 240 ha abandoned chalk quarry at Grays in Essex, now known as Chafford Hundred, is undergoing mixed development to include leisure facilities, a range of housing and commercial areas and an enhanced environment. The 120 ha of Stone Marshes now comprises the Crossways business park and the Dartford international ferry terminal. Reclamation and servicing required more work than had been anticipated and the fact that the area was within the green belt added to the delays, but Blue Circle was eventually able to provide a comprehensive development of the entire area to a high environmental standard. Stone Pit 1 landfill, at Dartford in Kent, is a former chalk quarry 40 ha in area and with an original average depth of 35 m. Landfilling commenced in 1976 and during the period 1979-1984 the site operator designed, developed and installed a gas collection and flaring system. From 1986 a gas plant supplied up to 5 000 000 therm/yr of landfill gas to a local cement works and in 1989 a 1 MW power generation scheme, later expanded to 3 MW, was commissioned. Gas is currently also supplied to a metal refining company for use in internal combustion engines

Aug 1, 1994

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By A. S. Macfarlane

The introduction of new technology into mining operations is seen as a strategic necessity by many mining companies, in order to improve safety and to improve operational effectiveness. Many attempts have been made in recent years to introduce new technologies into mining operations in southern Africa. Amongst these are noteworthy successes, as well as some disappointing failures. Often, the reason for failure does not lie with the technology itself, but with the work system into which the technology is introduced. Such failures may come with a significant opportunity cost, and have a detrimental effect on future development, simply because the system has not been adequately engineered, and the risks have not been adequately assessed and managed. This paper examines the reasons for such failures, and proposes a methodology to be followed to ensure successful and sustainable implementation of new technologies, such as to reduce technical and financial risk to the company, and to energize the workforce into ensuring the initial objectives of the project are met. The paper also focuses on the application of appropriate technology, and the development of technological applications which are commensurate with the level of development of the work environment into which it is introduced. The paper therefore focuses on the application of risk management, change management, systems engineering and feasibility analysis as being key elements of a successful and holistic technology implementation programme.

Jan 1, 2001

By A. R. Biggart, A. Walters, G. J. E. Kramer

The Owner Procurement Process or OPP is a proven, viable alternative contract delivery method that is potentially applicable to many tunnel projects. Using the OPP, the owner specifies and procures major tunnel construction items such as tunnel boring machines and tunnel linings and provides them to a tunnel excavation contractor in order to manage risk and accelerate project schedule. However, due to industry perceptions regarding potential owner risk, it is seldom considered or is rejected out of hand. In fact, past performance demonstrates that the process significantly minimizes owner, contractor and over-all project risk and mitigates the impact of any claims and differing site conditions. The paper outlines how the process should be structured to achieve schedule, cost, quality and risk management benefits. Potential and perceived disadvantages are discussed and how the process can be structured to mitigate or avoid them. The planned implementation of this process on the tunnels for the Silicon Valley Rapid Transit Project in San Jose, California is discussed.

Jan 1, 2005

By T. Warren, R. Pender

"Significant strides have been made during the past decade to integrate the traditionally separate administrative functions of financial management, materials management and maintenance management.In 1983, Key Lake Mining Corporation (KLMC) brought on-stream one of the most technologically advanced mining operations in North America. There was a requirement to support this new facility with state-of-the-art management information systems.This paper will discuss the development and evolution of the corporation's computerized information systems with specific emphasis on the utilization of computer systems to assist maintenance personnel in performing their work activities:Note: In August of 1989, the administration and operation of the Key Lake Mine was assumed by CAMECO - A Canadian Mining and Energy Corporation.IntroductionThe Key Lake Mining Corporation was incorporated in 1979 and operates a $500 million uranium mining and milling complex located in northern Saskatchewan.The feasibility study and environmental impact statements for the Key Lake Mine were submitted in 1979and in August of 1981, following a public inquiry, approval to proceed with construction was granted. Ore processing commenced in October of 1983 and during 1984 a total of 10.4 million pounds of uranium oxide (U3O8) was produced. In 1987, an annual production of 13.5 million pounds was achieved clearly establishing Key Lake Mining Corporation as the world's leading producer of uranium oxide. Current ore resources are expected to extend production of the Key Lake facility into the year 2000."

Jan 1, 1990

By I. Bock

Selective Blast Mining (SBM) makes use of milli-second sequential blasting technology to separate the valuable reef material from waste rock in the blasting operation at stope faces in the mining of tabular ore bodies such as exist in the gold and platinum mines in South Africa. The waste rock is cast blast to the back of the stoping area, and the reef material is fractured and deposited close to the stope face. Only the reef material is transported to the surface. A simplified economic model is presented to evaluate the economic benefits of SBM. Although premature, in that adequate experimental demonstration of the validity of the model has not yet been possible, the model is presented since it indicates substantial benefits in the case of narrow reef gold mines. It is suggested that many marginal mines should seriously consider SBM. Benefits can also be realised in platinum mines, but a lot more experimental work is necessary to establish cost parameters more reliably. Some practical experience in the use of SBM in the mining of the UG2 reef is presented.

Jan 1, 1998

By Refik Elibay, Lawrence A. Williamson, George D. Barnes

Under an extremely aggressive schedule, final design of 13.5 km (8.4 miles) miles of 8.2 m (27 ft) diameter deep rock tunnel, 322 ML/day (85 million gallons / day)submersible pumping station and associated facilities were accomplished ahead of a federal court mandated consent decree schedule. Challenges overcome by the project team in enabling timely completion of the construction documents will be presented. Discussion includes evolution of final design, consideration of future O&M requirements, and risks identified for construction and operations, together with measures to manage and proactively prepare for such risks.

Jan 1, 2005

By João Carlos Jânio Gigolotti

O avanço tecnológico tem gerado demanda crescente por materiais que possam ser utilizados em alta temperatura e ambientes oxidantes, o que inclui ligas intermetálicas MR–Si–B (MR = metal refratário) com estruturas multifásicas. Assim, este trabalho teve por objetivo estudar a microdureza de ligas do sistema Hf–Si–B na seção isotérmica a 1600ºC, na região rica em Hf. Ligas Hf–Si–B foram fundidas com lâminas de Hf (min. 99,8%), Si (min. 99,998%) e B (min. 99,5%), em forno a arco e tratadas termicamente a 1600 ºC em atmosfera de argônio. As relações de fases nessas ligas foram identificadas por difração de raios-X e por contraste, em imagens obtidas via microscopia eletrônica de varredura no modo elétrons retroespalhados. As ligas tiveram sua dureza medida pelo método Vickers (microdureza) com cargas de 0,05 kgf e 0,2 kgf e tempo de aplicação de 20 s. Os resultados, obtidos da média aritmética das medições realizadas nas regiões heterogêneas de cada liga, mostraram uma dureza média de 11,08 GPa, com pequeno coeficiente de variação de 3,8%. Os boretos HfB2 (19,34 GPa) e HfB (11,76 GPa) apresentaram dureza mais elevada que os silicetos Hf2Si (8,57 GPa), Hf5Si3 (9,63 GPa), Hf3Si2 (11,66 GPa), Hf5Si4 (10,00 GPa), HfSi (10,02 GPa) e HfSi2 (8,61 GPa).

Aug 17, 2017

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By P. R. Desam, J. D. Miller, A. Datta

The flow behavior of bubble-particle aggregates in separation tanks is important for many flotation systems, particularly for wastewater treatment. These aggregates can be considered as the dispersed phase in a continuous liquid phase of water and the flow characteristics determine the efficiency of the bubble separation process. In this work, a general methodology for the computational fluid dynamics (CFD) simulation of a bubble separation tank is described. This system is analyzed by Eulerian-Lagrangian approach. The momentum transfer from the dispersed phase to the continuous phase is quantified using the Particle-Source-In Cell (PSI-Cell) method. With CFD simulations, the effectiveness of different tank design parameters are evaluated in terms of the extent of bubble separation.

Jan 1, 2000

Jan 1, 1962

By J. H. Adkins

The goal of the project reported in this paper was to make recommendations for changes in roof bolting procedures and bolter design that would reduce roof bolter accident rates. To that end the project identified the major hazards associated with each task a roof bolter operator per-forms, normalized task accident frequencies. by the time spent on each task, reviewed equipment design features and operating procedures related to the identified hazards and developed recommendations for equipment and procedural changes that would reduce, if not eliminate, the hazards. The research steps completed during the project were: a. A review of related literature and re-search including roof bolting time studies b. The collection and analysis of 1975 accident data pertaining to roof bolter activities c. The normalization of the accident frequency data on the basis of time/task data d. A review of roof bolting equipment e. The development of a field data collection instrument f. The selection of mines for bolter observations g. The collection of field data h. Data analysis and problem specification i. The development of recommendations for corrective measures

Jan 1, 1978

By N. M. Skarbøvig

Safety nets have been used selectively in several South African mines over the years. Recently, however, an increased emphasis on mine safety has seen a resurgence of their utilization underground. This renewed interest has, however, also raised questions about the design and performance of these nets and their practical applications underground; these are the subjects of this paper. Generally, mine safety nets are used to protect personnel from falling rock in temporarily supported development ends, tunnels, ASGs and stopes. These diverse applications each require specific net designs, resulting in a wide product range. As a rule, however, mine safety nets need to carry specified static or dynamic loads with the least possible deformation. Because of the application-specific characteristics of mine safety nets, there is no South African national standard for them. Consequently, neither the SABS, nor the CSIR, performs standard tests on these components. In 2007, therefore, SIMRAC made available their Savuka facility for the testing of mine safety nets; the Savuka drop test became the accepted industry test standard for mine safety nets. From late 2007 to mid 2009, Norsenet, in collaboration with SRK Consulting, the designated operators of the site, conducted approximately 200 tests, which formed the core of Norsenet's database of safety net performance under various loading conditions. The test specimens comprised a wide range of net materials and config¬urations; the materials included: high density polyethylene, polypropylene, polyester, nylon, as well as a blend of polyester and polypropylene used primarily for reinforcement ropes. Net configurations encompassed the following parameters: net type, i.e., knotted nets or sewn nets; net strand type, i.e., braids, twines, or webbing; strand size; mesh size; mesh orientation, i.e., parallel or oblique to the net edge; net edge reinforcement, i.e., knotted, tied, with or without reinforcement ropes; internal reinforcement ropes, i.e., diagonal ropes and/or orthogonal ropes; as well as net attachment options, including loops and chainlinks. From the number of variables listed above, and the limited number of tests available, it can be appreciated that the findings of the test series required careful scrutiny. Nevertheless, principal performance factors clearly emerged: besides the obvious net mesh variables, such as net strand material, strand diameter and mesh size, it was the configuration of the reinforcement ropes and their attachment to the net panel which had the strongest influence on net performance. All the structural elements of a safety net need to work together to transfer the imposed load from the net panel, through the reinforcement ropes, to the net attachment points. In this load transference chain, the weakest link limits the strength of the structure. From this development work, Norsenet has gained valuable expertise to custom-design and manufacture nets to clients' specifications. The examples presented in the paper will also show the experience acquired in the installation of nets underground. Future work will include the establishment of a state-of-the-art net testing facility at Norsenet's factory in Vredenburg.. Keywords Mine safety net, safety net, protective device, mine safety, safety net design, safety net performance, safety net applications.

Jan 1, 2011

By Taehong Kim

An accurate and reliable prediction of Tunnel Boring Machine (TBM) performances, in terms of Rate of Penetration (ROP), utilization (U), and cutter wear rate, is a critical element in the successful planning and execution of mechanical tunneling project. Three open hard rock TBM projects were studied to establish possible trends and correlations between rock mass properties and machine performance. Based on this analysis and literature survey, three geological parameters, including RQD, RMR, and groundwater inflow rate, were identified as having the greatest impact on TBM utilization level. Rate of Penetration (ROP) and cutter wear rate were also correlated with fracture spacing, alpha angle, and Cerchar Abrasivity Index (CAI).

Jan 1, 2008

By Fredrick M. Ryan

Present indications are that in about 2-3 years phosphor tags will be required in commercial explosives. A permissible 254 run ultraviolet lamp assembly has been developed to permit mine inspectors to detect such phosphor tags and therefore to establish if non-permissible explosives were used. This new lamp is powered by a Miner's cap battery without interference with the normal lighting requirements of the cap lamp battery. It is compact, light, and rugged with very high ultraviolet output.

Jan 1, 1977

By S M. C Verryn, K Deysel

In heavy mineral sands ilmenite, rutile and zircon are present in economic concentrations. These minerals are important sources of Fe, Ti and Zr for various industrial uses. The beach sands of northern KwaZulu-Natal, along the Zululand Indian Ocean coastline in South Africa, have been mined for 30 years. The various processes involved in mining and processing these minerals have been controlled by time-consuming and labour-intensive analysis methods which, in some cases, can be replaced by X-ray powder diffraction (XRD)-Rietveld analysis. Heavy minerals are concentrated in the plant to produce a heavy mineral concentrate (HMC). The heavy mineral extraction plant is controlled and informed of the proportions of minerals in the HMC according to their magnetic susceptibility. The different fractions are called magnetic, paramagnetic and non-magnetic fractions and quality control is based on their magnetic fraction weights combined with X-ray fluorescence (XRF) elemental analysis. This current quality control process is very time consuming and labour intensive. We have aimed to show that we can, by XRD, identify and quantify all the minerals in the HMC and also in the magnetic separations. These results are then compared with results obtained by Mineral Liberation Analyser (MLA) as well as with the results from the physical separation. It was possible to detect all minerals present in the material by XRD and use the Rietveld method for a full bulk mineral quantification. A maximum of 15 minerals can be included in the Rietveld refinement due to computational restraints. Major minerals detected are rutile, ilmenite and zircon and minor minerals are quartz, epidote, anatase, amphibole, monazite, magnetite, titanite and augite. The XRD and MLA results correlate relatively well and detailed results will be presented for HMC and magnetic fraction samples. Small differences were observed for some minerals due to the different ways in which minerals are detected or due to preparation methods within each method. Rutile seems to be more abundant in the XRD analysis and the detection of Anatase is possible by XRD, but not MLA. Leucoxene (consisting of mainly microcrystalline anatase, rutile and titanite is not detectable by XRD since it is not a mineral, but ilmenite alteration phases are observed instead. There is, however, a correlation between anatase, titanite and rutile detected by XRD and leucoxene analysed by MLA.

Jan 1, 2008

?General Facts:Barrick?sFirst Mine in Peru Production started in November 1998 ?The Facilities:Open Pit, Primary and Secondary Crusher Valley Fill Heap Leach PadMerrill Crowe PlantRefinery Environmental Facts: High Rainfall - Average Annual Precipitation of 1,200 mm (47 inches) Rainfall Events: Common 20mm daily events High Altitude Site - Elevations range from 3900 to 4250m. Steep topography - Terrain ranges from 3:1 slopes up to cliffs. Water Issues: Sediment Control - Open Pit PAG Encapsulation - Waste Dump Stormwater control - Leach Pad Erosion Control Techniques ? Offsite impacts mitigation Social Issues: 11 communities surrounding the property Town of Huaraz

May 1, 2003

By Maurice J. Peterson

The applications of optical spectrochemical methods of analysis for determining trace impurities in metals are described, and the need for developing analytical procedures capable of accurately determining fractional parts per million of impurity elements in metals is stressed. Factors which determine sensitivity of detection and means to extend sensitivity levels in spectrochemical methods are discussed. Examples from the current literature illustrate the diversity of spectrochemical techniques that have been applied to the analyses of varied sample types, Many of the methods use preconcentration procedures to increase sensitivity limits. A bibliography containing abstracts of recent methods in included. Optical spectrochemical analysis is based upon the measurement of radiant energy emitted by atoms of the elements to be determined when a sample is subjected to a suitable source of excitation. The behavior of the valence electrons during excitation, usually by an arc, spark, or flame, produces radiant energy of specific wavelengths. This is recorded as spectral line images on a photographic film or plate by the spectrograph; for direct-reading instruments, the spectral lines are detected with photomultiplier tubes. The spectral lines result from the excitation of atoms in the sample. Each variety of atom produces its own characteristic set of lines, thus serving to identify the elements in the sample. Increased concentrations of elements in the excited sample results in increased blackening of the spectral line images.

Jan 1, 1961

By P. K. Hofmeyr

Base Metal (Cu, Ni, Mo, Zn, Co etc.) analysis traditionally has been very slow in conventional analytical laboratories which can lead to additional costs being incurred in waiting time of drill rigs or mining excessively off-reef. Recent developments in the automation of analytical laboratories now allow for very rapid turn-around times for base metal analytical data which can help reduce such costs as well as reduce the unit costs of the analyses themselves. 2.0 CONVENTIONAL ANALYTICAL LABORATORY PRACTICE Conventional analytical laboratories are necessarily are very manual. Sample preparation is slow and laborious, samples are moved from stage to stage manually and, typically, all samples are processed in batches so a sample which is the first to be, say, milled has to wait for the complete milling of the batch before it advances to the next stage eg. mixed with wax prior to pelletising for XRF analysis. Inevitably this results in long sample data turn-around times for laboratories handling large numbers of samples. Manual sample preparation can only be accelerated by increasing staff which increases costs and can lead to additional errors being introduced. Cleaning of sample preparation equipment, eg. crushers and mills, between samples is essential to avoid cross-contamination between samples and this is slow and labour-intensive. In manual sample preparation the correct sample numbers staying with the samples is totally dependent on the efficiency of laboratory operators. It is extremely difficult to detect when errors have occurred due to the switching of sample numbers during the sample preparation stages. Running duplicates and QC samples at best is only partially successful in detecting when sample number switching errors have occurred. Errors of this nature and cross-contamination problems due to incomplete cleaning of sample preparation equipment tend to occur when laboratories are working at pressure due to high sample numbers and when supervisors are not present during 24/7 laboratory operations which is often required on plant process control laboratories. These problems are common to all conventional analytical laboratories and their magnitude is dependent on the level of control and efficiency of QC systems practised by individual laboratories. The disadvantages of conventional manual analytical laboratories can be summarized as follows:- 1. Labour-intensive which is costly especially when multiple shifts have to be used during 24/7 operations.

Jan 1, 2005

By Steve C. Albrecht

The objective of this study is "to assess the impact of surface mining on soil compaction in the Midwest". The study revolves around a unique field sampling program targeted at four mine sites utilizing four distinct types of soil movement of midwestern prime land. Through the preparation of a final report for use as a guidebook, an assessment is made of the degree to which surface mining operations contribute to the soil compaction problem. The final report is formulated through the use of field study data as well as information gathered in an intense literature review. The final report centers on applying collected data to practical field applications. Soil sampling on the four mine sites centers on a comparison of natural and replaced soils for moist bulk density. This characterization evaluates changes in density and texture throughout the soil profile to a depth of 48 inches. Fertility of the topsoil is also assessed for natural and replaced soils. During field sampling and observations, a base of information has been gathered to compile a case study on each mine site. The report accesses the regulations in the prime farmland areas through the use of a matrix. The regulatory matrix allows easy access of mining personnel to State and Federal regulations.

Jan 1, 1982