Search Documents

Severe whipping of shuttle car trailing cables occurs when the car stops suddenly or reverses direction. This causes cable damage, and can seriously injure personnel near the cable. FMC has contracted with the U.S. Bureau of Mines to design, build and demonstrate a reel control system that will significantly reduce or eliminate whipping. II. CONCLUSIONS Results of engineering effort show that the following conditions are primarily responsible for the whipping problem. Causes may exist individually, or in combination.

Jan 1, 1972

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

Orebodies are defined in economic terms in that they must satisfy conditions determined by costs of mining, extraction and marketing before being so described. Despite this they have an essential chemical character as specialized products resulting from geochemical differentiation, and it is surprising that so little basic geochemical research has been carried out with respect to ore occurrence and that prospecting methods based on geochemical principles are not more widely applied.Many exploration geologists associate geochemistry with analytical techniques applied to the detection of dispersed traces of metals from actual orebodies. Geochemical research, applied to economic geology, goes far beyond this limited field and the purpose of this paper is to discuss aspects of such research and its use in formulating exploration principles.THE GEOCHEMICAL BACKGROUND TO MINERAL OCCURRENCE AND EXPLORATIONThe three aspects of economic mineral deposits to which geochemical research can be of use in determining ore guides are genesis, control of deposition and mode of dispersion from orebodies after emplacement. Prospecting for mineral deposits is primarily based on theories of ore occurrence which deal with the genetic and depositional influences controlling localization of ore. There are many such theories and they will not be discussed here as they have been adequately reviewed in geological publications. Some are based on differing argument concerning the same empirically observed associations of ore. In this respect it is perhaps fortunate that they are not always mutually exclusive as regards the...

Jan 1, 1960

Generation and Attachment of Submicron Size Bubbles to Colloidal Solids

Sep 13, 2010

By J Canterford

There is an apparent push to develop and commercialise "new and innovative" process flow sheets. A not-too-difficult reality check clearly demonstrates that the success rate of this push is not particularly significant and in fact could be regarded as a waste or misappropriation of R&D funding and the associated brain power. As Julian Sumner Miller would comment "why is this so?" To put it bluntly, many of the so-called innovative developments are equivalent to gold plating the dunny door - visually interesting but of very limited practical value. This presentation encapsulates some personal lessons learnt over the past 45 years.CITATION:Canterford, J, 2013. Developing a ænew and innovativeÆ process flow sheet - Traps for all players of all ages, in Proceedings MetPlant 2013 , pp 1-5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories and other ground control subjects and broad experience are required.

Jan 1, 2009

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

By Rimas Pakalnis, Andrea M. Ouchi, Thomas M. Brady, Mary M. MacLaughlin, Cristian Caceres, Paul Hughes

A major focus of ground control research presently being conducted by the Geomechanics Group at the University of British Columbia, Canada, in conjunction with the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory, is the development of design guidelines for underground mining within weak rock masses. The study expands upon the span design curve for man-entry operations and the stability graph for nonentry operations developed at UBC by extending the application to weak rock masses. The original database has been augmented by weak rock mass information from mines throughout the United States, Canada, Australia, Indonesia, and Europe. The common factor in all of these mines is the presence of a weak back and/or walls. This paper expands on the North American database and how the design curves have been employed at mining operations throughout the world. The definition of a weak rock mass for this study has been defined as having an RMR76 under 45% and/or a Q-value under 1.0.

Jan 5, 2007

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968

By David C. Uhrin

Two improved methods have been developed to transfer microfilmed mine maps to suitable base maps showing surface features. The methods provide for (1) positioning and orienting maps; (2) merging adjacent maps; and (3) plotting maps at a common scale. One method produces an overlay mosaic of mine maps using an Integrated camera-processor. This photographic method shows the details of mine workings and is most useful for specific limited-area projects. In the second method, outlines of mine maps are digitized, manipulated, and plotted as overlays using a computer. This computer method can plot mine outlines and spatially index large numbers of microfilmed maps. Microfilmed mine maps used in this Bureau of Mines study are on file in the Mine Map Repository of the Eastern Field Operations Center. The base maps are U.S. Geological Survey 7.5-minute topographic maps. The demonstration area is located in the New Kensington East and West quadrangles, Pennsylvania.

Jan 1, 1977

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1962

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

By Fernando Romero Lage

The purpose of this paper is to analyze detailed crushing and screening configurations and the interrelationship as they relate to mass flow balance, operating efficiency, plant availability and final production. The entropy of ore bodies limits the standardization of crushing and screening plants, however, consideration for a continuous and sensible assessment of the mass flow balance of the circuit will yield the best achievable results. Since energy costs have continuously risen in the last few years, it is imperative that these circuits offer low power requirements and low operating expenses. The paper will detail how the efficient implementation of continuous mass flow balance in the application of crushing and screening plants will generate quality improvement and process improvement, which will translate into bigger production and energy savings.

May 1, 2010

By Zach Ellis, Dusty Fisher

The Office of Surface Mining, Reclamation, and Enforcement (OSM) cited a large surface coal mine for a series of flyrock incidents that occurred when blasting close to the mining lease perimeter. The OSM placed the company on a pattern of violation status. It was determined through analysis of blasting practices that flyrock could be controlled at the mine by drilling a smaller diameter hole and stemming with crushed rock when blasting within 1,000’ (304 m) of the lease line. The procedure to install and remove the small diameter drill steel was cumbersome and dangerous because it was a manual transition. The drill carousel could only hold one diameter at the time the project was initiated. The process was very time consuming, involving a mechanic to transport the steel to the drill and spend up to 1.5 hours of downtime switching the steel. In addition, the hydraulically operated break-out wrench and break-out fork on the SKS Infinity Redrill® is only designed to work with one diameter, so these tools could not be used to disconnect subs and steels on the string. At the time, the mine’s breakdown was between 30-40% small diameter (6 ¾” (171 mm)) versus large diameter drilling (10 5/8” (270 mm)). The drill and blast group was challenged with the task to implement a 6s (Six Sigma) project that would reduce the amount of time spent on steel change-outs on the rotary drills while improving the safety of the task. A solution was proposed to carry the small diameter drill pipe, lower small diameter sub, and small diameter bit on board the drill at all times. The goal of the project was to carry the steel in the carousel after modification so that the driller could change the diameter himself on board the drill in less than 45 minutes without any assistance from a mechanic. The drill had to be modified so that the hydraulic operated break out wrench and deck fork could be utilized on both diameters. The drill accessory supplier and the mine worked together to design and implement design changes and new equipment onto two rotary drills, and new standard operating procedures (SOPs) were created for the new process. The project has been in the sustaining phase for approximately three months now and all steel diameter changes are completed by the operator under the allowable time limit.

Jan 1, 2015

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By G. Bulut

The recovery of copper and cobalt from ancient copper slags from the Küre region of Turkey was investigated. A fayalitic-type of ancient copper slag containing 1.24% Cu, 0.53% Co and 53.16% Fe were subjected to an experimental study. Two different routes were followed to recover the metal values. The first route was roasting the slag with pyrite followed by leaching. The second route was flotation of the slags, roasting of the flotation tailings with pyrite and leaching. The second route was found to be suitable for the treatment of the copper slag studied. In the flotation step, a copper concentrate containing approximately 11% Cu was produced with a 77% recovery while 93% of the cobalt stayed in the tailings. In the roasting experiments, the effects of roasting time, pyrite: slag ratio and roasting temperature on the dissolution efficiencies of Cu and Co were investigated, and the optimum conditions were determined. In the tests, 87% of the cobalt dissolution was observed after one hour of roasting at 500°C with a pyrite: slag ratio of 3:1. The copper dissolution in the tests was 31%. Based on the results of this study, a process flowsheet is proposed for the evaluation of these slags.

Jan 1, 2007

By Richard E. Bischke

Computer assisted finite element model analysis, originally developed to study stress distributions in aircraft, has been modified into a versatile mining program, that can be used to assist the engineer with predictions of mine subsidence. International Exploration, Inc. has developed an in-house finite element model program which incorporates a multitude of factors influencing mine subsidence such as mine design, physical rock properties, structure, faults, joints and topography. Finite element analysis of a mine model can mathematically determine the magnitude and direction of the principal stresses within each of the elements forming the model. By comparing the calculated in-situ stresses to the actual rock strengths, high risk regions within a mine can be identified. These potentially unstable regions of the mine can be allowed to fail within the model and the resultant stress redistribution and element movement calculated. Thus, the effects of the mine collapse at the surface can be predicted for the purpose of determining the potential damage, if any, that could occur to surface structures from deep mine failure. Stabilization materials can also be mathematically inserted into the model to design and analyze the effectiveness of subsidence prevention programs. Two examples are presented of the finite element program being used to predict mine subsidence at substantially different geologic and mining provinces in Pennsylvania.

Jan 1, 1984

By Russell J. Foster

In this Bureau of Mines report a selection process has identified 14 nonstockpiled materials (cesium, gallium, hafnium, indium, osmium, rhenium, rhodium, rubidium, ruthenium, scandium, selenium, tellurium, thallium, and zirconium) that are linked to the continuing evolution of high-technology fields such as electronics, catalysis, and energy, and that have limiting factors associated with domestic availability. A qualitative assessment of the "potential criticality" of these materials was made through a consideration of end uses, demand trends and forecasts, production, mineral reserves, byproduct status, alternative supply sources, substitution and conservation options, and recyclability.

Jan 1, 1988

By C. H. Riggs

"INTRODUCTION The injection of gas into the McClosky limestone in the adjoining, Griffin and New Harmony field in Indiana and Illinois and resulting increases in oil and gas production from this zone ore described in this report.Since 1911, the use of compressed air or as to increase oil production by supplementing natural reservoir energy has been widely adopted, and has resulted in the recovery of much additional oil, which otherwise would have been left underground. In many of the newer oil fields, including Griffin and New Harmony, a part of the compressed residue gas from natural gasoline plants is returned to the reservoir as a secondary method to increase oil and gasoline production. Part of the injected gas is stored underground for future use.By presenting data on many secondary recovery operations in a series of reports 5-9/ the Bureau of Mines has sought to stimulate interest in secondary recovery as a means of increasing oil recovery and current oil production for wartime needs. Most of the elder fields in the United States produce oil from sandstone reservoirs, and probably more than 90 percent of secondary recovery operations have been developed in oil bearing sandstones. During recent years, the volume of oil obtained by primary methods from limestone reservoirs has increased steadily, but as yet little has been done to recover, by secondary means,,the large volumes of oil left in limestone reservoirs when primary methods production are no longer profitable. Because of inherent differences in the origin and nature of the pore spaces between sandstones and limestones and because of differences in permeability and fluid content, secondary recovery methods, which are successful in sandstone-reservoirs, are not always applicable to limestones. Not much he been written concerning secondary recovery operations in limestone reservoirs, and few data are available to assist operators in developing such secondary recovery projects."

Jul 1, 1945