Search Documents

As part of its research on advanced mining technology, the U.S. Bureau of Mines emphasizes studies on in situ leach mining. This research enables the Bureau to develop technical information that can allow mining companies to adopt in situ leach mining methods. Research results should help to remove the technical and economic barriers currently hindering the development of commercial in situ leach mining operations. This report contains papers summarizing results of Bureau research on various aspects of in situ leach mining. A featured topic is the cooperative field experiment of the Bureau and Santa Cruz Joint Venture in a copper deposit near Casa Grande, AZ. Discussions in-clude an overview of the entire project, cost modeling, environmental permitting, laboratory core-leaching experiments, petrographic studies, and an evaluation of the geologic structure in the region. In addition, papers describe hydrologic modeling and geophysical studies of solution flow during leaching. Preliminary geochemical modeling studies are also summarized. A final paper describes a nonionic chemical additive with potential for significantly reducing the high costs of drilling in in situ leach mining.

Jan 1, 1989

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By Tarrant Elkington

Underground mine planning practices are typically manual and time consuming and will often produce sub-optimal solutions due to the application of generic rule-of-thumb assumptions or ?tried and tested? choices. The development of computer-automated tools for underground mine planning enable a wide range of scenarios to be considered rapidly in arriving at an optimised solution, subject to input assumptions. We have applied these tools to demonstrate ?optimised? solutions that challenge industry standard practices. Further, we have incorporated grade and price/cost uncertainty into these tools to gain an understanding on how the consideration of uncertainty may further alter strategy selection. Finally, we enable the tools to dynamically adjust cut-off grades in conjunction with the evolution of prices/cost.

May 1, 2010

By G Small, A Lazamanana, C Greet

When conducting gold leach tests on free milling gold ores which method is the best, bottle rolls or the stirred beaker test? Recently, a client requested that gold leach tests be conducted using the stirred beaker methodology. When asked why, because the laboratory was set up to conduct tests using the bottle rolls technique the reply was that the stirred beaker leach test would replicate the plant more closely. Not wishing to upset the client, the instructions were followed. However, the opportunity was taken to complete additional tests so that the two leach procedures could be compared. Further, this comparison was completed on two different gold ores as well as a number of different grinding media types.This paper provides a description of the two laboratory techniques employed, and presents the results of these parallel tests. Interestingly, the assertion that the stirred beaker methodology more closely replicated plant performance was not validated. In fact, the results obtained using this procedure were noticeably different from those observed in the plant, with lower recoveries and significantly higher cyanide consumptions. The bottle rolls test however more adequately replicated plant performance in terms of recovery and cyanide consumption. The reasons for this are discussed in the paper.CITATION:Greet, C, Lazamanana, A and Small, G, 2015. Bottle rolls versus stirred beaker leach testing – which is best?, in Proceedings MetPlant 2015, pp 188–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By L. W. Higley

Electrowinning metals from solutions leached from low-grade ores is becoming an increasingly important extraction method as the metal industry turns to pollution-free recovery processes. Lead-alloy anodes are used industrially in the electrolytic recovery of zinc and copper. However, associated with the use of these anodes are the inherent problems of stability and lead contamination of the cathode. In an effort to eliminate these problems, the Bureau of Mines has developed a relatively inexpensive lead dioxide anode for electrowinning metals from strong acid solutions. The anode was prepared by depositing Pb02 directly on a titanium blank in a strong HN03-Pb(N03)2 solution at 2.15 to 6.45 A/dm2 and 60° C. This anode was tested in zinc and copper electrowinning cells containing 200 gpl H2S04 and 35 to 100 gpl metal ions at the current density of 3.23 to 6.45 A/dm2. Contamination of the cathode by lead was =0.005 pet. A 30-day test at 6.45 to 12.90 A/dm2 in an electrolyte containing 200 gpl H2S04 and no metal ions resulted in a slight change in surface morphology of the Pb02 anode but no measurable change in anode weight or dimensions.

Jan 1, 1976

Minerals contribute to the U.S. gross domestic prod-uct (GDP) at several levels?mining, processing and manufacturing finished products. In 2008, the estimated growth rate for the real GDP of the United States was 1.1 percent and the nominal GDP was about $14.3 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. For instance, continued declines in the U.S. housing market during 2008 were reflected in further reductions in the production and consumption of cement, clays, construction sand and gravel and crushed stone (mineral commodities that are used almost exclusively in construction), and those associated with the related manufacture of goods, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard ? all used by the housing industry. The widespread effects of the slowing domestic economy became more apparent in the last three to six months of 2008 when prices for many mineral commodities declined sharply after reaching record highs earlier in the year, indicating significantly lower demand for those materials or products containing them.

Jan 1, 2009

By W. V. Mutler

Present day capital costs are analysed for a 2 000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By O. W. Owings

"The handling and transportation of explosives and explosives supplies are inherently hazardous owing to their sensitiveness to impact and flame or electric arcs and sparks. Many accidents have occurred in the past during transportation of explosives, especially when they were carried by individual miners on man-trips. When electric haulage became the usual mode of transportation and shots were fired electrically, the hazards of carrying explosives and supplies on man-trips were fully realized, and in some mines all explosives were placed in one car, usually at the rear of the trip. Far-sighted managers saw the danger of this practice and provided separate trips for delivering explosives. This step was a definite advance in safety, but the latest achievement is the construction of special, rugged, nonconducting cars.Many coal-mining men have shown considerable interest in the construction of safe cars for explosives during recent months. Undoubtedly many others are interested in this phase of safety, therefore this circular is issued to give information on cars of this type now in use.Car A (fig. 1) is essentially a closed inner box separated from an outer box by an insulating lining of rubber. The double box is attached to a standard steel chassis that has spring journals and electric welding instead of certain rivets. The chassis is equipped with roller bearings. The over-all length from pin to pin is 11 feet, 9 inches; the wheel base is 54 inches, the track gage 42 inches, and the capacity eighteen 50-pound cases of permissible explosives. The box is 10 feet long, 6 feet wide, 3 feet high at the top of the arched roof, and 2 feet 9 inches at the edges. The top of the car is 46 inches above the top of the rail.The inner box is insulated from the outer box by two pieces of 1/4-inch switchboard.-insulating matting cemented together. To cover the top, two ends, two sides, and the bottom of the box requires 320 square feet of the l/4- inch matting.The walls are well-seasoned tongue-and-groove oak, 1 1/4 inches thick and 2 3/4 inches wide. A 1 1/4-inch air space is maintained by oak strips between the outer wall and the two thicknesses of 1/4-inch rubber matting. The inner box is made of 7/8-inch, well-seasoned, tongue-and groove oak fitted closely against the insulating matting. No nail, rivet, or bolt extends through the rubber insulation.The floor of the outer box is secured to the chassis by two sets of bolts through an intermediate piece of well-seasoned oak. One set of bolts is countersunk from the top of the intermediate piece of oak, and the other set is countersunk from the bottom. The countersunk portions are filled with ""insulate,"" an insulating compound. Adjacent bolts are at least 6 inches apart.The bed of the inner box is divided into six compartments by transverse strips of wood at the bottom and partitions near the roof. Each compartment accommodates three 50-pound cases of explosives. This arrangement prevents cases in adjacent compartments from touching, so that there is no possibility of end thrust of the entire load of explosives. Each inner compartment is 21 inches high, 5g inches long, and 16 1/4 inches wide. Separating strips at the floor are 3 inches wide and 1 1/4 inches thick. The outside dimensions of the 50-pound cases of explosives used are 17 1/2 inches long, 13 1/2 inches wide, and 12 1/2 inches high."

May 1, 1940

By Christopher Mark

Pillar recovery continues to be one of the more hazardous activities in underground coal mining. Safety requires that the roof above the intersection remain stable until after the pillar has been extracted. Artificial supports (timbers and Mobile Roof Supports) arc essential to roof stability, but so is the final remnant stump or pushout. Traditional mining practices usually called for the complete extraction of the final stump, but the recent trend (both in the U.S. and internationally) seems to be towards mining plans that leave a remnant stump. For this study, a sample of roof control plans from the Mine Health and Safety Administration (MSHA) Coal Districts were analyzed to determine current pillar recovery practices. Both full- and partial- extraction plans were included. Special attention was paid to whether plans require that a final stump be left, and whether requirements regarding the dimensions of the remnant stump are included. Foreign experience with final stumps is also summarized. It seems that the risk of major pillar falls can often be reduced by leaving final stumps that are large enough to protect the intersection, but small enough that they do not inhibit the caving of the gob. Because final stumps are often irregular in shape, a new approach for estimating their strength is described. Analyses were conducted to assess the effect of seam height and depth of cover on the potential variation in the size of remnant stumps.

Jan 1, 2001

By Cory J. E. Yacyshyn

Anchored steel pipe piles are being used more frequently in British Columbia for shoreline projects such as public ferries, cruise ship docks, containership terminals and locally in the expansion of the Vancouver waterfront convention center. While a 36? diameter driven pile may provide adequate compression loads it will not always achieve enough penetration to provide the required tension loading. That is why bundles of threaded anchors or strands are drilled through the center, past the pile tip, and anchored into the underlying strata. Drilling up to 250 feet deep through the piles in variable water bearing strata presents challenges. Southwest Contacting Ltd. (SWC) recently completed the three largest anchored pile projects in BC; Vancouver Port and Convention Center Expansion, Vanterm Container Terminal and the new Prince Rupert Cruise Ship Terminal. This paper will present the separate challenges encountered drilling the anchors. At Prince Rupert, the recently completed Northland Cruise Ship Dock ultimately required a cased system to drill and install triple thread bar anchors. When 200 foot long steel pipe piling was unable to penetrate the highly fractured gneiss/schist bedrock to obtain a seal and consolidation grouting was unsuccessful, a modified cased system was advanced deep enough into the rock to eventually seal. The 3-#20 bars were changed to 12-strands since the bars wouldn?t fit through the smaller cased hole. The options were limited because each dolphin only had enough room for a small hydraulic drill rig that wouldn?t have the power to fully case the holes. The Canada Place Pier Extension in Vancouver?s Harbor led to the development of an innovative tip design used later at Vanterm. The 36? diameter steel pipe piles were driven closed end but modified to permit drilling through a concrete plug at the base. The driving of the piles at Canada Place often knocked out the plug so we were faced with 50 feet of sand up inside the pile when the drilling started. This led to discussions on how to safely remove the sand, solidify the tip, and continue drilling to get past the tip without undermining the pile. Finally, Vanterm Berth Extension was completed with a unique drilling system because the pile tips stopped in hydraulic sands, as opposed to the native till. We were faced with advancing the casing to the till without undermining the base of the pile. With 100 psi water pressure at the pile base after we broke through the concrete plug, the trick was to prevent charging the sand with our 250 psi air which liquefies it and forced it up our drill casing. And of course, it has to happen just before Christmas holidays!

Jan 1, 2004

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

By M. Mikhaylenko

Rhenium, molybdenum and tungsten are the elements demanded by high-end technologies. These metals are found in process solutions in forms of their oxyanions: ReO4-, MoO42- and WO42-. The later two can exist in forms of iso- and/or heteropolyanions. Basically all three metals demonstrate very similar chemical behavior in aqueous solutions. Unfortunately, in their mineral sources these elements commonly accompany each other, like pairs of rhenium-molybdenum or molybdenum-tungsten. Their economical separation is a challenging task.

Jan 1, 2012

By D. Hatfield

"Flotation plants typically aim to maximise recovery at or above a target grade. As the ore from the mine varies, operators increase or decrease the mass pull in different flotation banks by adjusting air and level set points in order to achieve target concentrate grade. A methodology has been developed to maximise overall recovery at target grade by determining the optimal mass pull for each bank. However, the approach of targeting equal grade for each ore type in the deposit leads to sub-optimal overall recovery. This is because some ore types sacrifice a large amount of recovery to reach target grade while others easily achieve target grade and can be processed at higher than target grade for little or no loss in recovery. Processing different ore types at different grades and blending the concentrates therefore gives a higher overall recovery.This paper presents a case study where an 80 year production forecast was made for a large Chilean copper concentrator in feasibility stage. A circuit model was created using SGS’s Integrated Geometallurgical Simulator (IGS) for the different ore types to be processed. The model was calibrated from standard rougher flotation tests (MFT), cleaner tests and from the results of plant surveys of similar operations. The pull rates for each bank in the circuit were determined to achieve an optimal graderecovery curve for each ore type. These curves were combined at different concentrate grades for each ore type to obtain the mathematically optimal overall recovery at target grade. The paper shows a methodology for obtaining an optimal combination of operating conditions for each ore type to maximise overall recovery at a set combined concentrate grade."

Jan 1, 2013

By A Weber, L MacNamara, H Schreiber

Design and development of the world?s largest flotation cell was completed in 2002. This was the first 257 m3 flotation cell installed in the mineral industry and represents a major development in the design of larger flotation cells. This cell has a 50% increase in volume over the widely installed 160 m3 WEMCO® Smartcell? flotation machine. In the next few years it is anticipated that 257 m3 flotation cells will be incorporated into rougher-scavenger flotation circuits in many more world class copper sulphide concentrators. The prototype 257 m3 cell, No.250 Smartcell? flotation machine was installed at Minera Los Pelambres in the front of Row 1 in the existing rougher flotation circuit. This cell is followed by nine No. 130 Smartcell? flotation cells. After the successful development phase, this unit has been incorporated as part of a row of No. 250 Smartcell? flotation machines at Minera Los Pelambres. A key to the successful development of the equipment has been the emphasis placed on fundamental hydrodynamic scale-up criteria. Hydrodynamic factors include superficial gas velocity, water (pulp) circulation through the draft tube, and pulp mixing (distribution) characteristics. This paper will review the scale-up criteria of the No. 250 flotation cell, and present a case study of the in-plant equipment testing. The case study will document the metallurgical and hydrodynamic performance of the machine. It will also illustrate the economic benefits derived by incorporating larger flotation cells in a modern copper sulphide concentrator.

Jan 1, 2007

By M E. Taulis, S Hayton, D A. Manhire, J G. Pope

Successful development of coal seam gas (CSG) resources in low-rank coalfields such as the Powder River Basin has raised interest in CSG from low rank coal in New Zealand. Kenham Holdings Limited holds 12 Petroleum Exploration Permits (PEP) covering some of New ZealandÆs low-rank coal and lignite resources and has engaged CRL Energy Limited to assist in the systematic evaluation of the CSG potential of the permits. To date, exploration results from seven New Zealand coalfields reflect differences in coal type, rank, depositional environment and depth of burial between coalfields. Several of the explored coalfields are considered prospective for CSG. One of the most advanced Kenham exploration programmes is in the Hawkdun Coalfield, Central Otago.   The Hawkdun Coalfield contains a single, thick lignite seam with properties that are similar to the Powder River Basin. Preliminary results indicate the Hawkdun Coalfield is prospective for CSG with the potential to contain between 25 and 60 PJ of gas; enough to supply a 30MW power station for ten to 25 years. Further drilling is planned to investigate the economic viability of the Hawkdun Coalfield. The in situ permeability of the lignite, the amount and availability of free gas, gas saturation at depth and market opportunities will determine its economic viability. If initial pumping and production results in the planned exploration programme are promising, the Hawkdun Coalfield will be further developed with additional production drillholes to form a trial production pod.

Jan 1, 2004

By G de Jong, W Sunyoto, K Sari, P Silalahi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Big Gossan mine is operated by PT Freeport Indonesia and is one of the largest stope-and-fill mining systems in the world. The Big Gossan deposit is a ~200 m wide, 1200 m long and 500 m high steeply north-east-dipping to subvertical skarn body at the Cretaceous-Tertiary Ekmai-Waripi contact. The copper-gold mineralisation, with a 1.3 per cent copper equivalent cut-off grade, occurs mainly proximal to the Ekmai-Waripi contact in the garnet-clinopyroxene prograde skarn at the base of the Tertiary Waripi formation and partly distal to the contact in the tremolite-actinolite retrograde skarn of the Tertiary Waripi formation.The Big Gossan stope mine is designed from 2540 m to 3020 m above sea level. Present active stoping operations occur at level 2540 mL to level 2640 mL and are done in a primary and secondary stoping sequence. The width and length of the stopes is 15 m and 20 m respectively, while the height of the stope varies between 20 m and 40 m, depending on the ground conditions. The stability of the stopes is visualised in the Mathew’s Stope Stability graphs. These graphs and actual Cavity Measurement Scanner measurements on the stope will predict and show the overbreak and underbreak, which affect the reconciliation of the mined stope and also the pillar stability between the primary stopes. Geological factors like major structures, joints, veins and alteration intensity are important factors that correlated with the stability of the Big Gossan stopes.CITATION:Sari, K, de Jong, G, Silalahi, P and Sunyoto, W, 2015. Stope stability at the Big Gossan skarn deposit, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 139–146 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

[ ]

Jan 1, 1942

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By M. K. Elmouttie, G. V. Poropat

Mapping of exposed rock walls provides data on geological features such as joints, bedding planes, faults etc critical to the economics and the safety of mine operations. Traditional, manual methods of mapping can be time consuming, error prone and limited in their coverage. New methods have been developed to map exposed faces remotely and safely however the benefits of these methods are only fully realised when exposed structures can be quickly and easily mapped using automated methods. This paper describes the application of an automated method of analysis of 3D images that provides users with the capacity to map exposed structures automatically. The method is based on the use of vector classification methods used in some neural network systems and provides rapid and reliable identification of exposed planes. CSIRO Exploration and Mining is applying these methods to 3D images for a range of applications from pit mapping to machine automation.

Jan 1, 2006

Economic Sustainable Power for Mineral Processing

Sep 13, 2010