Search Documents

By Alex C. Smith, Michael J. Sapko

A series of explosive detonation experiments was conducted in NIOSH’s Bruceton and Lake Lynn Experimental Mines to evaluate low level (<6 psig) detonation wave propagation behavior in single and multiple entry configurations. Entry cross-sectional area varied from 5 to140 m2 and explosive weights of Pentolite ranged from 0.24 to 2.4 kg. Behavior of the detonation wave was evaluated through recording of the pressure as a function of time and distance from the explosive detonation in single and multiple entry interconnecting tunnels. Peak pressure from detonation of an explosive in an underground mine maintains magnitude for a greater distance than is the case on the surface and is shown to follow the simple scaling rela-tionship P = 702.8(W/Vt)0.514(0.65)n, where P is the peak detonation pressure in kPa, W is the weight of the explosive charge in kg, Vt is the total volume in m3, and n is the number of splits, n = 0, 1, 2, …n. The total energy, or impulse, I, generated by these detonations can be expressed as I = 1.34(W/A)0.64n, where W is the weight of the explosive charge in kg, A is the area of the main tunnel in m2, and n is the number of side en-tries, n = 0, 1, 2, …n.

By Jon Sinnreich

Ensuring the accuracy of collected data during deep foundation static load tests is of paramount importance. Typically, pile head displacements are measured relative to a purpose-built reference system, which is assumed to be fixed. This study presents a simplified error analysis of this assumption, illustrates the potential magnitude of these errors, and proposes an improved method of pile head displacement monitoring.

Jan 1, 2009

By C. Thiart

Kriging is an interpolation technique for predicting unobserved responses at target locations from observed responses at specified locations. Kriging predictors are best linear unbiased predictors (BLUPs) and the precision of the BLUP is assessed by the mean square prediction error (MSPE), commonly known as the kriging variance. Both the BLUP and the MSPE depend on the covariance function describing the spatial correlation between locations and on specific parameters. The parameters are usually treated as known, whereas in practice they invariably have to be estimated and the empirical BLUP (that is, the EBLUP) so obtained. The empirical or estimated mean square prediction error (EMSPE), or the so called ?plug-in? kriging variance estimator, underestimates the true kriging variance of the EBLUP, at least in general. In this paper five estimators for the kriging variance of the EBLUP are considered and compared by means of a simulation study in which a Gaussian distribution for the responses, an exponential structure for the covariance function, and three levels of spatial correlation ? weak, moderate, and strong ? are adopted. The Prasad-Rao estimator obtained using restricted or residual maximum likelihood (REML) is recommended for moderate and strong spatial correlation and the Kacker-Harville estimator for weak correlation in the random fields.

Jan 1, 2014

By Bülent Erdem, Zekeriya Duran, Tuğba Doğan

The objective of this study was to evaluate the potential health risk associated with exposure of dozer operators to whole-body vibration. Measurements were made on 31 dozers used in different surface mines in Turkey. Predictions of adverse health effects of vibration were based on the standards BS 6841:1987, ISO 2631–1:1997, ISO 2631–5:2004, and the EU Vibration Directive:2002. Operators experienced high and comparable levels of vibration acceleration and dose during all dozer tasks: pushing the material (DOZE), moving forward (FORWARD), moving backward (REVERSE), and ripping (RIP). Specifically, DOZE, FORWARD, REVERSE, and RIP showed high potential of adverse health effects in terms of vibration dose according to the worst-case axis and vector sum criteria and a moderate adverse health effect for acceleration according to the worst-case axis criterion. Operators of large dozers were exposed to lower levels of vibration. However, no statistically significant relationship between vibration exposure levels and the propelling mechanism and the service time of dozers, operator experience, operator age, and ground type was found.

Jun 16, 2022

Flow Sheet Simulation of Municipal Waste Treatment Processes

Sep 13, 2010

By M. G. Zabetakis

This publication contains highlights of a 4-hour lecture and demonstration by the Bureau of Mines on the fire and explosion hazards of flammable liquids and solids, oxidizing materials, corrosive liquids, and compressed gases. The authors first presented this material as part of a 2-week course given to officers and enlisted men at the U.S. Coast Guard&apos;s Dangerous-Cargo Handling School, established at Fort Eustis, Va., in 1959. The Bureau was asked to present the lecture and demonstration because of the extensive experience of its researchers in handling certain harardous commodities.

Jan 1, 1961

By G. B. Harris, A. R. Laplante

Fine tungsten was used to mimic gold and fine and coarse silica and magnetite to mimic gangue. The optimum flow rate of fluidisation water varied from 1.7 l/min for fine silica to 5.6 l/min for coarse magnetite. Overloading at optimum flow rate was then investigated. With fine silica gangue no overload occurred under any of the conditions studied, and there was very little overload with fine magnetite. Coarse silica caused appreciable overload, but only after a significant bed of tungsten had been formed; with fine magnetite gangue the onset of overloading occurred earlier. Finally, with coarse magnetite severe overloading occurred almost immediately. Overloading was modelled using a first-order kinetic rate constant for erosion of the concentrate bed and a critical mass of constant above which it takes place. The results clearly demonstrate the importance of removing oversize to maximise recovery, particularly with a high-density gangue

Jun 18, 1905

By R. J. Forzatti

The production of sulphuric acid from sulphur generates heat. The majority of this heat is recovered as steam and is often used to generate electricity. Heat not recovered as steam is rejected to cooling water systems. The design of the turbine, condenser, and cooling water systems impacts the overall water, energy, and environmental footprint of the plant. This review considers a conceptual 2000 t/d sulphuric acid plant with several alternative cooling water systems. The review utilizes Hatch?s 4 Quadrant sustainable design tool to compare the alternatives on both an economic and a weighted sustainability scale.

Jan 1, 2014

When we are beset with the economic problems the world faces today, we are always inclined to look at the shorter term future. Today I would like to take a long-term view of our industry, project historical demands for our products into the future and discuss opportunities for our members. Perhaps we could firstly look at the long-term demand trends for our metals. If I tend to use non ferrous metals as a basis for my figures it is because this data is more readily available to me. I am sure that most other products of our industry show similar trends.

Jan 1, 1992

By G. Roger Miller, Kristine M. Krajnak, Stephen S. Leonard, Stacey Waugh

Repeated exposure to hand-arm vibration through the use of vibrating hand tools can result in the development of the disorder known as hand-arm vibration syndrome (HAVS; (1,3)). One of the hallmark symptoms of HAVS is cold-induced peripheral vasospasms that result in finger blanching (4). Although the vascular and neural pathology associated with vasospasms has been described, little is known about cellular mechanisms leading to this damage (4). To understand how vibration may alter vascular and neural physiology and anatomy, rats were exposed to a single bout of tail vibration and the molecular responses of neural and vascular tissues were measured to determine if there are immediate or sustained affects of vibration that may underlie longer term changes in physiology. Methods Experiment 1. Male Sprague Dawley rats (n = 32, 6 weeks of age) were housed in AAALAC accredited facilities. All procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guidelines for care and use of laboratory animals. Vibration exposures were performed by restraining rats in Broome-style restrainers, and securing their tails to a vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control rats were treated in the same manner, except that the tail platform was mounted on isolation blocks and not on a shaker. The vibration exposure was 125 Hz, 49 m/s2, for 4 h. Rats were euthanized with an overdose of pentobarbital (100 mg/kg) 1 h or 24 hours after the exposure. RTqPCR was used to measure transcript levels for endothelin 1 (ET-1), the 3 forms of nitric oxide synthetase (NOS) NOS-1, NOS-2, NOS-3 and norepinephrine receptor subtypes 1D, 2A, 2C, in artery tissue, and to measure calcitonin gene-related peptide (CGRP) and nitric oxide synthase-1 (NOS-1) in ventral nerves. Data were analyzed using 2-way ANOVAs. Experiment 2. Male Sprague Dawley rats (n =24, 6 weeks of age) were maintained as described above. Animals were exposed to a single bout of restraint or vibration. Another group of animals served as cage controls. All animals were euthanized 24 h after the exposure, and tail arteries were isolated and frozen. Reactive oxygen species ROS) were measured using electron spin resonance spectroscopy (ESR). Arteries were homogenized over ice in 1 ml of PBS with protease inhibitor cocktail, using a tissue tearer (Biospecs Products Inc. Racine, WI USA). The sample was split into two 0.5 ml samples. One set had PBS and the spin label hydroxyl-TEMPO [0.1 mM] added while the other set had hydroxyl-TEMPO [1.0 mM] plus the specific hydroxyl radical scavenger, dimethylthiourea (DMTU), added to confirm the presence of the hydroxyl radical. Samples were vortexed and then placed in a flat cell for ESR analysis. The ESR spectrometer settings were: receiver gain, 6.32 x 102; time constant, 0.02 s; modulation amplitude, 1.0 G; scan time, 20 sec; magnetic field, 3490 ± 100 G (2). Data were analyzed using 1-way ANOVAs.

Jan 6, 2006

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By M Simpson

Greywackes of the greater Auckland Region (Brynderwyn Hills to Hamilton), when considered on a regional scale, have characteristic ranges of physical, mineralogical and other properties. Some properties (eg density, porosity, crushing resistance, clay index) generally cluster and correlate with the basement greywacke facies, regions and terranes recognised by geologists, and their diagenetic/metamorphic level. Other local factors, particularly variations in mineralogical composition, nature of matrix cement, grain size, and degree of weathering may produce aberrant properties. Some of these local variations, when extreme, have the potential to affect the aggregateÆs performance in roading or the concrete industries. &nbsp; Smectite and the zeolite laumontite are the major deleterious minerals occurring in fresh greywacke rocks of the Auckland region, although weathered rocks may contain halloysite, an expanding member of the kaolin clay mineral group. These minerals, when found in abnormally high levels in greywackes cause expansion effects in the aggregate. Currently there are inconsistencies in the detailed correlation of shrinkage, clay index, clay mineral content and intrinsic expansion data that need further research to resolve them. &nbsp;

Jan 1, 2007

Based on X-ray phase analysis and exploratory experiments, a new technology was developed to recycle multiple valuable elements in spent Al2O3-based catalyst. The experimental results showed that after roasting at 750°C for 30 minutes at an Na2O:Al2O3 mol ratio of 1.2, the leaching recoveries of alumina, vanadium and molybdenum from the spent catalyst were 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by barium hydroxide and barium aluminate. The precipitation recovery of vanadium and molybdenum was 94.8% and 92.6%, respectively. Al(OH)3 is prepared from sodium aluminate solution using the carbonation decomposition process. The purity of Al2O3 is 99.9% after calcinations, and the recovery of alumina can reach 90.6% in the whole process. The Ni-Co concentrate was leached with sulfuric acid, and a nickel recovery of 98.2% and a cobalt recovery of more than 98.5% were obtained under the experimental condition of 30% (w/w) H2SO4, 80°C, a liquid: solid ratio of 8:1 (by weight), a reaction time of 4 hours and a stirring rate of 800 rpm.

Jan 1, 2007

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners. &nbsp; The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

Separation of Iron Particles from Banded Haematite Quartzite (BHQ) Ore by Selective Magnetic Coating The separation of fine iron particles from banded hematite quartzite (BHQ) has been studied using selective magnetic coating. The BHQ ore assays as 38.9 per cent Fe, 42.5 per cent SiO2 and 1.0 per cent Al2O3. Mineralogically, the ore contains hematite and quartz as the major mineral phases where as goethite and magnetite is present in minor entities. Natural magnetite of very fine size and oleate-magnetite in colloidal form, prepared synthetically in the laboratory are used as the coating material on the surface of hematite particles. The selective coatings of oleate-magnetite on BHQ surfaces followed by magnetic separation studies have indicated that, it is possible to achieve 62.3 per cent Fe with 8.5 per cent SiO2 at 85.4 per cent iron recovery. The recovery of iron values is found to be superior in comparison to the conventional magnetic separation techniques. The selectivity of coating for enhancing the magnetic response of iron particles is achieved by controlling the surface properties of the particle via electrokinetic potential adjustment by controling pH and addition of oleate-magnetite. In the separation process, the effects of pH, magnetic intensity and addition of oleate-magnetite are studied to achieve the maximum grade and recovery of iron values. The optimum separation is observed at pH of 7.5, oleate-magnetite concentration of 0.25 ml/g of BHQ ore and a magnetic intensity of around 0.8 Tesla. The X-ray diffraction (XRD), Infra-red spectroscopy (IR) and UV-visible spectroscopic studies strongly suggest preferential coating of magnetite on hematite surfaces. Scanning electron microscopy (SEM) studies have brought out the semi-quantitative features of BHQ ore. The recovery of iron values from a lean grade ore such as BHQ is carried out looking into the future needs of this ore in India for iron and steel making.

Sep 13, 2010

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By C. Crussard, R. Tamhankar

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers accord-ing to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Gerhurd Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Staff Coordinator, James J. Burke THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Past-President; John Chiprnan, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman; Dennis Carney, John Chip-man, J. C. Fulton, J. H. Hollomon, H. H. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and D. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman, F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham, .Jr., Robert F. Hehemonn, R. I. Jaffee, F. E. Jaumot, Jr., Irving R. Kramer, A. J. Lena, Harold Margolin, C. J. McHorgue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alan U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B. King, F. C. Langenberg, W. 0. Philbrook, and T. 0. Winkler. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AIME members. Single copies, $4.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AIME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts... Second class postage paid at New Yark, N. Y., and Ann Arbor, Mich. Volume 212, Number 6.

Jan 1, 1959

By P S. Datta, V N. Misra

Higher bed height up to 680 mm, including 30 mm hearth layer of sized return sinter and high suction below the grate bars up to 1400 mm WG have resulted in increasing the productivity to a level of 33 t/m2/day and reduced coke rate to a level of 46 kg/tonne sinter. The ferro-wastes like blue dust, flue dust, mill scale, collection from dust catcher and gas cleaning plant, etc have been successfully added in charge mix to produce quality sinters. In this paper, brief description of the work done at Regional Research Laboratory (CSIR) in last few years and two case studies are discussed including the successful development of pan sintering units.

Jan 1, 2002

By L. C. St. Arnaud

"Open pit mines can produce large disturbances within regional hydrogeologic systems. The degree of disturbance and the consequences on the local environment depend on the size of the pit and on the physical setting of the mine. Comparisons and contrasts are presented for three Noranda base metal open pit mine sites.The Brunswick Mining and Smelting No 6 open pit has a surface area of 11 ha and a depth of 185 m. It is located within complexly deformed schists and meta-volcanic rocks. The massive sulphide and iron formations visible along the north and southwest walls of the pit generate acid drainage. Mining ceased in 1983, and the pit is presently being filled with waste rock and neutralized drainage water. Water balance calculations estimated a total fill up time of sixteen years. As the water level rises, leakage to groundwater could take place across a fault zone intersecting the pit.The Mattabi Mines F-Group pit has a surface area of approximately 3 ha and a depth of 50 m and is also set in meta-volcanic rocks and acid generating iron formations. Production at this site ceased in 1982, and the low pH pit water is neutralized and pumped into a nearby lake at least every five years. Major water inflows are from precipitation and groundwater. Groundwater mounds within adjacent high land surrounding the pit provide a natural hydraulic barrier to groundwater flow, except for the southeast side. As a consequence, the pit water elevation is being kept below the elevation of the nearby creek in which some of the pit water could drain.The Bell Copper open pit covers an area of 40 ha and is 270 m deep. With present ore reserves, the mine might be in operation until 1992. The geology around the pit consists of andesitic tufts, siltstones and shales, and the acid generation potential of the rock is relatively low. A recent hydrogeological study estimated fill up time by precipitation and groundwater to be in the order of 260 years.With increasingly more stringent requirements for mine closure, it is anticipated that more detailed hydrological and hydrogeological studies of open pits will be required to determine post-closure environmental impacts and the suitability of open pits for mine waste disposal."

Jan 1, 1990