Search Documents

By Sharpe E. J

The Triton lode is a schistose feldspar biotite chlorite rock with quartz, carbonate, pyrite and some pyrrhotite. Its more chloritic sections strongly resemble the enclosing greenstones, its more feldspathic portions are indistinguishable from the flne-grained phases of the porphyry dyke into which the southern extremity of the ore body merges. The ore body' has a length of 880 ft. and an average width of I2t ft.; in places this widens to as much as 30 ft.The average dip is 85° west and pitch of the ore shoot 75° south.METHOD OF SAMPLING.With the exception of a limited amount of channel sampling (a reference to which is made elsewhere in this paper) all the sampling is by chip sample.The samplers use a hammer weighing approximately 11 lb. and chip directly into the sample bags. Sampling is generally carried out over 3-ft. sections and portions thereof to the nearest half foot-thus a face 8t ft. wide is divided up into two sections of 3 ft. each and one section of 2 ft.-no measurements of less than 4 ft. are used and calculations are all in feet and dwt. per long ton.In the oxidised stopes wp.ere the lode is much narrower, .i.e., 6 ft., sampling is over 2-ft. sections. All borehole samples are over 2-ft. sections, this corresponding approximately to steel changes.(a) DEVELOPMENT SAMPLING.Driving.-This is done by following the east wall and each face is sampled-this corresponding to an advance of 5 ft. If the full width o,f the lode is not exposed boreholes...

Jan 1, 1938

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By Claude Deveau, Stephen R. Young

Introduction Tanco History Tanco is sometimes known as the Bernic Lake Mine. It is located about 180 km east-northeast of Winnipeg close to the Manitoba-Ontario boundary. Tanco operates an underground mine employing ramp access, room and pillar mining and shaft hoisting for the production of tantalum, lithium and cesium minerals. Tantalum recovery employs conventional gravity and centrifugal concentration methods along with a flotation process which recovers ultra-fine tantalum. All tantalum concentrates are shipped to Cabot Supermetals, Boyertown, Pa., for the production of tantalum chemicals and metals. Tanco also produces lithium products from spodumene ore. The lithium concentrates from Tanco are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock to the on-site chemical plant dedicated to the production of cesium formate, a high density drilling fluid. Tantalum milling operations commenced in 1969. In the early years of the operation, feed grades were three to four times as high as they are today. Coarse-grained tantalum mineralization with complete tantalum liberation at sizes of 300 µm allowed for easy recovery with conventional equipment such as spirals and shaking tables. Over the years, the process and feed material to the plant have drastically changed. Due to drastically reduced liberation sizes, efforts have been made to try to recover as much of the liberated particles as possible in order to maintain acceptable recoveries.

Jan 1, 2005

In today?s high tech world, systems are getting bigger, faster, better. To remain at the leading edge, in any business, depends on accurate but flexible design thereby allowing operational managers to provide alternatives to improve their operations. The ultimate goal is to deliver to plan, with optimum economics. Mining is no different, with falling prices and escalating costs, improved margins become the focal objective. There are many ways to achieve this, ranging from operational efficiency improvements through production scenarios to planning initiatives. Of all, planning usually receives the least attention, yet it is the area of most influence on the NPV of the reserve. With computer technology, numerous concepts and iterations are possible thereby closing the gap between optimal and actual design. This paper discusses the application of the split shell design at the De Beers Venetia open pit in South Africa.

Jan 1, 2001

By Colin Curtis

In recent years, Manchester Airport has undergone expansion including the construction of a second runway, a new terminal building (Terminal 3) and extensions to the existing Terminal 1. Manchester is Britains third largest airport and ranked 20th in the world for international traffic. Arup (Manchester) was engaged as consulting engineer in a multi-disciplinary role for the terminal works. Part of this was a geotechnical commission including site investigation and pile design followed by supervision. This paper reviews the piling for the old, new and terminal extensions. In total, five pile types have been utilised over the years. The original 1950's Terminal 1 was founded on driven cast in situ piles, with a later 1970's extension utilising rotary augured piles. The recent piling comprised continuous flight auger piles (CFA), driven steel tube and tripod bored; the latter in areas of restricted access or low headroom. The ground conditions are Made Ground over thin Alluvial and Glacial drift, in turn, over a generally weak to moderately weak gypsiferous mudstone. All the piles were socketed into the mudstone. In terms of the new CFA piles, quality control using the instrumentation monitoring was problematical, but a substantial static load and integrity test programme resolved pile performance. Part of the work is matching new pile performance with previously installed piles and the continued use of older piles with new loads. Research provided some data on the older piles, including some static load test data, which enabled back analyses of their design and likely behaviour. Differences in design methods, installation techniques and pile behaviour based on load tests will be discussed.

Jan 1, 2001

By Martin G. Castro, Renato G. Bautista, Morton Smutz

During the last 25 years, multistage mixer-settlers have been used extensively for liquid ion exchange work. The mixer-settler has the advantage of being a compact device in which a large number of stages can be assembled in a relatively small area. They are particularly advantageous for the separation of rare earths. Most of the adjacent rare earths have separation factors which are near one, which means that a large number of stages are needed to produce a good separation. When two elements (m, n) are extracted simultaneously, the separation factor (ßm, n) is defined as: [ ] where Ym, Yn are the molarities of the respective elements in the organic phase and Xm, Xn, are their molarities in the aqueous phase at equilibrium. The industrial consumption of rare earth oxides rose to over 6800 tons in 1968, an increase of 33% over 1967.1 The increased production and demand for rare earth and lanthanum chlorides for petroleum cracking catalysts was one of the principal factors in this increased consumption of rare earths. In 1968 approximately 59% of the rare earth oxides produced were used for gasoline cracking catalysts in the form of rare earth and lanthanum chlorides. There was also an increase in the sales of lanthanum oxides for use in optical lenses and in fiber optics. The future looks good for the rare earth industry. The rare earths can be expected to be used in many new products which are being developed. Until the late 1950's tributyl phosphate (TBP) was the principal solvent used in rare earth liquid ion exchange. In 1957 Peppard3 reported the use of di (2-ethyl-hexyl) phosphoric acid (D2EHPA) as a solvent for separating the rare earths. Rare earth separation factors of up to 2.5 were obtained in nitrate and chloride systems while the maximum separation factor using the

Jan 1, 1972

Who's Who in Mineral Engineering 1977 - SME Membership Directory of the Society of Mining Engineers of AIME

Jan 7, 1977

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By Hayward SB, First DM

The Maragorik Prospect represents a partially eroded Pliocene acid sulphate style epithermal gold system hosted within the Sigule Volcanics and Riet Bed sediments which is inferred to have formed from a degassing porphyry body at depth. A regional sinistral rotation provided by transform faults associated with the opening of the Manus Basin imparts a dilational character to mineralised NE trending faults formed parallel to the Warangoi Graben. A controlled-source audio magneto-tellurics (CSAMT) survey has identified E-W trending buried conductors which may represent alteration formed within dilation zones. While some gold mineralisation occurs within vuggy silica at Palang Hill, the target is auriferous enargite (luzonite)-bearing breccias from the LK1 and Gureki areas.

Jan 1, 1991

By P Storey, B Deans, T Lancaster

Straits completed its Feasibility study on the Whim Creek Copper Project in 1996. At this stage WCCP provided Straits with an open pit mine - heap leach - SX-EW copper project to follow on from its successful Girilambone Copper Operation (GCC). Since this time Straits has continued to review WCCP investigating a number of development and production scenarios. The development of Whim Creek, early 2004 and is on schedule to commence copper production in the final quarter of 2004. On current reserves Whim Creek will produce approximately 17 000 tonnes of copper cathode per annum for three to four years, at cash costs of The paper will cover a general description of the project, the project development and key design issues. Additional construction related issues associated with the complete relocation of the GCC plant to Whim Creek will be covered in the conference presentation.

Jan 1, 2004

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office- workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections:

Jan 1, 1963

By Chris Bennett, Drupad Desai, Kirit Mevawala

INTRODUCTION The design/build (D/B) philosophy of contract delivery is neither new nor unusual when it comes to at-grade, elevated or high-rise structures. But when it comes to constructing underground facilities, there were no examples to be followed in early 90sin the continental United States or its territories. When DMJM+HARRIS was selected as general architectural and engineering consultant for the Tren Urbano (TU) project in Puerto Rico, one of the requirements of the Federal Transit Administration (FTA) for funding commitment was to use TU as a demonstration project utilizing design/build contract delivery method. Now fifteen years later, New York City Transit (NYCT) has instituted a similar requirement for their first Tunnel Boring Machine (TBM) contract for the Second Avenue Subway. As with most construction mega-projects, lots of things have happened and there were several lessons learned from the TU experience that are now being applied to Second Avenue. Both of these projects require building tunnels and underground transit facilities in heavily traveled corridors of an urban city, in the vicinity of active business and commercial enterprises. To enhance the challenge, there are noise and vibration sensitive and historic urban receptors either over or along both the transit corridors. Column free Tren Urbano station caverns over18 m (60 ft.) wide were built in soft ground conditions within 3.6 m (12 ft.) of the surface under an aging heavy utility corridor, while NYCT tunnels with station structures stretching the limits of rock caverns to 34.8 m (100 ft.), were planned in rocky geology with the presence of shear and fault zones and some mixed face conditions. BACKGROUND During the early period of design/build experimentation, the speed with which the contract procurement packages could be put together enabled the owners to take advantage of the major efforts underway to rebuild the infrastructure that was suffering from post-World War II neglect. Use of design/build for new starts was unheard of and most of the projects were smaller in nature in order to allow the methodology to be tested. Development of functional design packages with the understanding that the D/B

Jan 1, 2005

By Moorrees C, Everson P

A detailed examination of carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite shows that the rate and extent of magnesium and iron dissolution are affected by the slake time, leaching temperature, carbon dioxide pressure, pulp density and rate of agitation. In order to produce high-purity magnesia from the leachate by precipitation and calcination, the optimum leaching conditions, which are those that yield maximum magnesium and minimum iron dissolution, have to be a compromise in terms of the above parameters. For example, iron dissolution can be limited by leaching at an elevated temperature (-45°C), but because the maximum concentration of magnesium biearbonate decreases rapidly with an increase in temperature, it is necessary to use a low pulp density (-2 per cent solids) in order to achieve an acceptable degree of magnesium dissolution.Evidence is obtained that iron dissolution involves the formation of a soluble ferric bicarbonate complex that decomposes at elevated temperatures. The extent of iron dissolution is much higher than might be expected and it is probably because the original magnesite contains siderite in solid solution with the magnesite; on calcination, the hematite whieh is formed is in a very finely divided condition and hence more reactive.

Jan 1, 1983

By Stanton Johnson

Africa has a long history of mining and has been one’of the world’s greatest sources of gold and other mineral resources since the days of the Egyptian pharaohs. Mining in Africa has been dominated by South Africa since World War II. However, in the past 10 to 15 years, other African countries are beginning to slowly catch up with South Africa. Ghana, formerly called the “Gold Coast” is located on the West Coast of Africa. Ghana has been involved in mining activities for well over 100 years. Most of the mining activities centered on the mining of gold and were to a large extent limited to underground mining methods. With a more liberal economic policy regarding the exploration and exploitation of Ghana’s mineral resources, mining activities are beginning to evolve to a much larger scale. Drilling and blasting which is an important aspect of this evolution is also changing due to the involvement of foreign-based mining and explosives companies.

Jan 1, 1998

By G T. Kukla

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland û Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground subsection of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes operational. Support of the site's system continues from head office which is continually involved in development of SUMPS and issuing revision updates to sites. The users, as well as programmers, were mostly geologists and mining engineers. This helped to ensure rapid, successful implementation. The broad approach of this system was to use interactively the specialist skills and interpretative abilities of the user mining engineers and geologists with the data manipulation abilities of the computer. It is an integrated system which covers geological exploration, deposit modelling, mine planning and production scheduling. An important feature of the system is that the user has full interactive control over each function through a graphics terminal where applicable.

Jan 1, 1980

By Gustav Wirth

"ABSTRACTIn exothermic and endothermic catalytic reactions, control of the temperature is of utmost importance. Basic calculations are developed for determining catalyst volumes of various types of reactors that give particular temperature distributions, and the individual designs are compared.INTRODUCTIONA narrow range of permissible operating temperatures characterizes many, catalytic reactions, and yields of the desired product are reduced sharply if operating temperatures fall outside of this optimum range. In order to achieve close temperature control, reactors with internal heat exchange have been developed in which thin layers of catalyst are located between cooling surfaces.The temperature distribution for an exothermic reaction in such a thin catalyst layer is shown in figure 1. Reactive gases flow downward through the catalyst section, which is 2so wide. It is assumed that a constant amount of heat is generated per unit of bulk catalyst volume, and that this heat is entirely removed through the walls. Consequently, except for a short section at the entrance of the reactor, the heat of reaction is not available for raising the temperature of the gases. Thus, at all points equidistant from the axis, the temperature is the same throughout the entire reactor. At the middle of the gas stream, the temperature is designated as uo. Traveling radially from this point, the temperature decreases because of the removal of heat through the walls and reaches, in the vicinity of the cooling surface, the value u1. Over a relatively narrow zone of width, b, the temperature falls to the value u2 at the cooling surface. Because inadequate data are available on heat-transfer coefficients for a gas flowing through a porous bed, and also because the narrow zone, b, is probably without effect on the reaction by virtue of its low temperature, the temperature drop in this zone at the cooling wall was disregarded. The following calculations were made on the basis of the temperature drop (u0 - u1) resulting from heat conduction within the main body of the catalyst bed only."

Nov 1, 1950

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987

By A. B. Cook, C. J. Walker, G. B. Spencer

Although water will displace oil from a petroleum reservoir to a greater extent than gas will, there are some reservoirs in which gas rather than water should be used for pressure maintenance. This is indicated by the high-percentage oil recovery in the case history reports on the Pickton field1 in East Texas and the Raleigh field2 in Mississippi. In gas cycling, total oil recovery includes vaporized products from the immobile oil in addition to oil produced by displacement. If a large part of the immobile oil is vaporized, total oil recovery may be higher than that obtainable from pressure maintenance by water injection. However, the amount of immobile oil vaporized may range from almost 0 to 100 percent, and no simple and reliable method has been presented in the literature for calculating oil vaporization. Development of such a method was the purpose of this study. Several papers concerning the calculation of oil vaporization have been published,3 6 and each is based on the concept dealing with K values — equilibrium constants for the various components in reservoir oils. (K for a component in a system of vapor and liquid in equilibrium is the mole fraction in the vapor phase divided by the mole fraction in the liquid phase.) This appears to be the most logical approach. Yet, the problem is too great for a perfect solution, even with modem laboratories to analyze oils and high-speed digital computers to perform calculations; the number of components in reservoir oils is too large. Because of their complexity no two reservoir oils are exactly alike. Also, K values change not only with variations in pressure and temperature but also with composition of the reservoir oil. In addition, during gas cycling, the lighter hydrocarbons tend to vaporize first. Thus, the reservoir oil becomes more dense and less volatile as gas cycling continues. Furthermore, the greatest amount of oil vaporization occurs near the injection well. Therefore, a simplified method is required for calculating oil vaporization because a rigorous method is not practical. The present methods of calculating vaporization generally require knowledge of the reservoir oil composition in which the mole fractions of the lighter components through hexanes are given; the remaining oil is described as C, + (heptanes and others of greater molecular weights). Assigning one K value for the C,+ system provides the simplest solution, but this incorrectly assumes that K for C, + does not change as gas cycling continues. This assumption can cause large errors because the K value may become less than a thousandth of the original after a large amount of oil vaporization. Another way to solve the problem is to determine changing K values for C, + according to how much of the C, + has been vaporized. To determine these values a sample of the reservoir oil is injected into a pressure-volume cell, and dry gas is batched in and out of the cell. Appropriate measurements and tests are made to determine K

Jan 1, 1970

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011