Search Documents

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

1. BOYD, JAMES. Statement on the Investigation of Natural Resources. Hearings before National Re-sources Economic Subcommittee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 125-131. 2. BUCH, J. W., HENDRICKS, T. A., AND TOENGES, A. L. Statement on the Investigation of Natural Resources. Hearings before National Resources Economic Sub-committee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 231-235. 3. CONGRESS, U.S. An Act to Provide for the Establishment and Operation of a Research Laboratory in the Pennsylvania Anthracite Region for Investigation of the Mining, Preparation, and Utilization of Anthracite, for the Development of New Uses and Markets, for Improvement of Health and Safety in Mining, and for a Comprehensive Study of the Region to Aid in the Solution of Its Economic Problems and to Make Its Natural and Human Resources of Maxi-mum Usefulness in the War Effort. Public, No. 812, 77th Cong., 2d sess. (S-357), ch. 764, approved Dec. IS, 1942, 2 pp.

Jan 1, 1962

To optimise the haulage of the large tonnages produced from stopes in this high production gold mine, an ore pass and feeder system was introduced. This ore pass was designed and developed in 2006 and the plate feeder installed and commissioned soon after. Cavity Monitoring Surveys (CMS) have been undertaken of the ore pass since it was commissioned. The original thickness that was surveyed of the pillar between the ore pass and decline in 2006 was approximated to be 19 m. Throughout its use large blocks of rock were reporting at the plate feeder. This was the first indication that the ore pass was failing somewhere between the tipping level of the 9410 level and the plate feeder at the 9330. Even so CMS surveys were not taken systematically to firstly identify the area of failure or for monitoring. In August 2008 after implementing management systems, large blocks were still reporting to the plate feeder. The decision was made to empty the pass enough to carry out a CMS survey of the area. Subsequently it was discovered that the area of failure was between the decline and ore pass and that since the first survey the pillar thickness had been reduced to approximately 9.7 m. Further management controls were put in place to slow movement of the material and to limit the use of the 9410 tipping level, but this did not alleviate the rate of failure entirely. The results of an initial inelastic numerical model indicated that most of the pillar was damaged and that failure into the decline likely if no changes were made. The numerical modelling predicted that even if material was no longer passing through the ore pass interaction between the voids was unavoidable and would most likely result in instability. The ore pass and plate feeder are an integral part of the haulage system for the remaining life-of-mnie. Two solutions were sought to firstly reinforce and stabilise the pillar between the ore pass and decline and secondly to rehabilitate the ore pass or find an alternate design that could still utilise the plate feeder. This paper summarises the analysis and resulting rehabilitation that was used to accomplish this.

Nov 25, 2010

By Robinson KJ

Education in Australia now has to respond to a very wide political and policy agenda. The political emphasis is upon increasing participation and retention rates with a view to greater graduation rates in `high-tech' disciplines. There is an implied linkage between `education' and `economic well-being'. Our argument is that equalitarianism in education tends towards mediocrity. In this context many Geoscience educators view the future with pessimism. The argument is that science has been `sold short' and needs revitalising. We contend that Geoscience coursework should be a feature of both secondary and tertiary education in Australia. To this end we propose six policy initiatives to increase the content of Geoscience in education programmes.

Jan 1, 1989

By W B. Edgar, I M. Platten, C A. J Towsey, B W. Cuffley

The evaluation of historical goldfields has been common over the past 15 years, reflecting changing economic conditions, improvements in knowledge and technology and lack of greenfield sites. Many goldfields comprise narrow gold-quartz veins, which are structurally complex with an irregular distribution of gold, have variable geometry and architecture and display late deformational effects. The study of historical mine records can be an important tool during early and advanced project evaluation, since it contributes to understanding the orebody, exploration target size and setting expectations. Mine records include documents such as plans, sections, reports, news cuttings, production tabulations, etc. A major advantage for the modern explorer is the capability of computer modelling to display this data in 3D. Historical records can give the explorer substantial information on various deposit characteristics, not least grade and geological continuity, geometry and architecture, mineralogy, metallurgical properties, bulk density and ground conditions. From an evaluation perspective, historical records can be used to support a Mineral Resource estimate, though its application will depend upon the quality and quantity of the data and judgement of the Competent Person. Effectively used, historical records can reduce geological uncertainty and focus evaluation efforts û thus reducing project risk.

Jan 1, 2009

Population growth, social inequality, pollution, global warming, poverty, overexploitation of natural resources and biodiversity loss, are a few examples of the many challenges facing the world today. Sustainable development is about meeting these challenges and improving the standard of living for the benefit of the maximum number of people. These issues concern governments, communities, environmental and social action groups and individuals all over the world. Business too, has a fundamental role to play in delivering sustainable development. In particular, sustainable development is becoming increasingly recognised as a critical issue for the oil and gas industry to address and act upon. BP is committed to positively respond to the challenges posed by the objective of sustainable development.

Jan 1, 2002

By D. A. Lindsey

Gravel lithology affects the quality of aggregate because different rock types in gravel have different physical and chemical properties. The lithologic composition of alluvial gravel reflects the composition of its source terrane and the variable effects of weathering and transport on each rock type. This report discusses lithologic controls on aggregate quality in the mountain-front environment of the Colorado Front Range. Lithologic controls on aggregate quality of gravels were evaluated using pebble count data. Gravel lithology along the Front Range shows both temporal and regional variation. The principal variable in gravel lithology is quartz plus quartzite, of which quartzite is commonly more abundant. Large quantities of metaquartzite derived from the mountain front southwest of Boulder, Colo., were dispersed northeastward during deposition of the oldest Front Range gravels. Average quartz plus quartzite is greatest in the oldest gravels. Aggregate quality is probably enhanced by large quantities of quartzite. Abundant volcanic rocks in gravel may enhance aggregate quantity, but such occurrences are local in extent. Abundant sedimentary rocks in gravel, mainly sandstone near the mountain front, may decrease aggregate quality.

Jan 1, 2002

By NONE N

Jan 1, 1963

By Jochen Petersen, Thandazile Moyo

"The oxidative leaching of chalcopyrite in ammoniacal solutions has been evaluated using electro-analytical techniques. The anodic dissolution process has been established to be a seven-electron transfer process under nitrogen in ammonia–ammonium sulphate solutions and ammonia–ammonium carbonate solutions. The number of electrons transferred in the carbonate and sulphate salts suggests that the sulphur is oxidised to a thiosulphate intermediate and the copper and iron released as Cu+ and Fe2+. The Cu+ and Fe2+ is subsequently oxidised in solution in non-Faradaic reactions. The deportment of Fe2+ and S2O32- is affected by choice of the ammonium salt used in the leaching process. In the perchlorate salt, only five electrons are transferred, however observations made on the mineral surface after leaching do not support the formation of elemental sulphur. Scanning electron microscopy and energy-dispersive spectroscopy analysis of the mineral surface suggest presence of an iron–sulphur surface layer completely free of copper under the ammonia–ammonium sulphate conditions, an iron-rich surface layer under ammonia–ammonium perchlorate solutions and absence of surface layer build up under ammonia–ammonium carbonate solutions. INTRODUCTION Hydrometallurgical processes for copper extraction provide a viable route to recover the metal from mixed and low-grade ores, as well as overcome the environmental challenges faced by the traditional pyrometallurgical processes. Chalcopyrite is not only the most abundant of the copper sulphides, but also the most stable, making it recalcitrant to hydrometallurgical processes. Hence, hydrometallurgical processing of chalcopyrite continues to be an attractive area of research due to the vaguely understood surface chemistry of the mineral in different aqueous media. Different approaches to hydrometallurgical treatment of chalcopyrite can be carried out. These include thermal treatment prior to leaching, direct leaching and direct electrochemical leaching (Venkatachalam, 1991). Direct leaching of chalcopyrite can be carried out in various solution systems, as reviewed by Roman and Benner (1973) and Venkatachalam (1991). Ammoniacal solutions are attractive and effective lixiviants that form stable amine complexes with some base-metal cations while rejecting iron. Leaching of chalcopyrite in ammoniacal solutions in the presence of an oxidant is possible due to the stabilisation of copper(I) and copper (II) by ammonia at elevated pH levels. In oxygenated ammonia solutions, it has been suggested that chalcopyrite dissolves according to Equation 1 (Beckstead & Miller, 1977a):"

Jan 1, 2015

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By G. X. Wang, R. E. Siemens, M. C. Fuerstenau, D. Chandra

Soda roasting of concentrates from Mouat, Montana, was performed in a temperature range of 450 to 650 degrees C and chromium was solubilised by water leaching at room temperature. It was found that high extraction yields of chromium were primarily dependent on the conversion of Cr3+ to Cr6+ during the roasting step, and this was enhanced significantly by simple attrition of chromite particles during this step. Gangue impurities (mainly Si) were more detrimental to Cr extraction than lattice impurities such as Al or Mg. It appears that oxidation proceeds into grains along a preferred crystallographic plane in the cubic lattice of the chromite. The effects of roasting time, temperature, soda to chromite ratio and particle size on the extraction of chromium are presented

Jun 18, 1905

By R. L. Amelunxen

"In January 1983, Gibraltar Mines Ltd. started an exploratory program on Column Flotation with hopes of improving performance of the Molybdenum Cleaning circuit. The encouraging results led to a column test trial in the Bulk Copper Cleaner circuit where the test unit has per¬formed well. A program was undertaken to understand the mechanics of column operation. A year and a half later, Gibraltar is considering the replacement of existing Bulk Copper and Moly Cleaning flotation cells with a fully computer con¬trolled Column Flotation circuit.BRIEF SUMMARY OF TESTWORKInitial testwork was done with a home made 20 inch diameter x 31 foot high column, equipped with a doppler flow-meter at the tail line and automatic level conrol. This loop maintained constant level in the column by throttling the tail valve. This column was placed in a variety of locations around the Moly circuit as shown on Figure 1 a, b. Test re¬sults indicated that the column could achieve much higher grades than the conventional cells, but recovery wise, the performance was low. Spillages from overloaded pump boxes were a common frustration during this time.Column control strategy was reviewed; and, in light of information received from McGill University, changed to conform with the methods that had been employed by D. Wheeler, of the Column Co. of Canada4 and Gaspe Copper Mines3.The column was tested replacing a portion of the bank, figure lc. The results obtained were more or less equal to the circuit. However, as we had Nitrogen gas connected to the column and not the regular cells, the column was kept in service. With the use of Nitrogen in the column, the usual copper depressant, Sodium Cyanide could be replaced with Sodium Hydrosulphide, hence lower operating cost.As time went on, a 10 inch diameter column was added in series to re-treat the concentrate of the 20 inch diameter column with hopes that the copper content would decrease from 0.6% down to 0.3% in order to save on subsequent leach¬ing costs. So far, results indicate there has been some im-provement, hut we are not achieving 0.3% copper. (See figure 1d)."

Jan 1, 1985

By C. Lemmer

The resolution with which the different categories of resources are forecast for Witwatersrand gold reefs should ideally tie in with block sizes that are optimal in terms of the variability structures of the reefs. A tool, called the ?variancegram?, is proposed as a basis for block size choice. A variancegram is intrinsic to the particular reef and mine concerned. A further requirement is the ability to attach global confidence limits to weighted average estimates built up from combinations of local kriged estimates. Approximations to derive global kriging variances based on variables derived from local kriging deliver hugely inflated results if ordinary kriging is used, and markedly better, but not accurate, values if simple kriging is used. These approximations improve as the number of samples used in kriging each block is increased. It is shown that the behaviour of the different components of the global kriging variance with increasing number of samples, all differs, but they all link to the variancegram for the particular reef. The variancegram can thus be used to correct the different components to the values they would have had if all samples were used in kriging each block, and so deliver the ?correct? global kriging variance, even though only a limited number of samples were used in kriging each block. The desirability of having very stable solutions implemented in production systems is taken into account in the proposals. It is anticipated that the same variancegram findings will also hold for other densely sampled deposits, but this remains to be investigated.

Jan 1, 2014

A wide-ranging base of jig data was collected from various types of commercial jigs in 9 coal preparation plants in China, and a complete data analysis was made. It was found that the sharpness ofseparation was very variable, which demonstrates the complex interplay of the many factors which influence jig performance. Tests showed that there exist optimum frequency ranges in each compartment of a jig. Stepwise regression analysis indicated that the sharpness of separation is most sensitive to the intake fraction ofthe air cycle, the frequency, and the feed rate. By means of non-linear curve fitting techniques and statistical analysis, several mathematical models were developed to describe both partition curve and the jig performance, for simulation purposes.

Jan 1, 1986

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

By J M. Laboz Bernard

Among the numerous technical evolutions in the blasting environment we are going to describe below the concep

Jan 1, 1995

By Ernest M. Spokes

For bituminous and lignite coals the economic picture continued to improve as it has each year since the low of 1961, with production at 480 mil- lion tons in 1964 compared with 1963's 459 million tons. The anthracite industry produced 16.3 million tons in 1964 and 18.3 million tons in 1963. The industry is looking toward a further expansion; among the new developments will be a mining wheel producing 3 million tons of lignite per year in South Dakota. It is expected that electric power generation will continue to provide the market for most of the increase in consumption, with exports second in importance in the expansion. Improvements in methods of mining and transporting coal underground and in strip mines, and the cooperation of carriers in finding ways to reduce transportation costs to distant markets, have made possible these expansions. Research continues to reduce costs of mining, transportation, steam generation of electric power and production of steam for space heating and manufacturing processes, to retain some markets and expand others. Other research seeks to expand markets by developing fuel from coal which will be more attractive than competing fuels, by reducing sulfur and other sources of air pollution. Public relations efforts of the industry are bearing fruit in a greater acceptance of coal as a modern fuel.

Jan 2, 1965

By T. Y. Yunsel

Estimation techniques such as polygonal, triangular prism, trapezoid, isopach maps, and inverse distance methods are often used in ore or industrial minerals deposit evaluation. These techniques do not express the variability of the deposit and do not allow a determination of the reliability of the estimates. However, geostatistical methods can express a measure of the error associated with the estimates, by finding weighting coefficients for a given mining block, and can also help with data configuration that minimizes the error. This work addresses an application study on the quality and reserve characteristics of the cement raw materials of the Adana Cement Factory in Adana, Turkey, based on the spatial distribution and variability of the chemical components (Si02, CaO, A1203, Fe203). The study has been carried out using a geostatistical procedure that is useful for site assessment, characterization, and monitoring situations where data are collected spatially. Directional and omnidirectional experimental variograms of the cement raw material variables showed that neither strong geometric nor severe zonal anisotropy exists in the data. The most evident spatial dependence structure expressing the continuity for omnidirectional experimental variograms were characterized by exponential and spherical variogram models. These models have been used in cross¬-validation analysis, which proved that these models, their parameters, and kriging parameters are applicable for the study area. Quality contour maps of the deposits at given levels underground were estimated using a kriging interpolation technique. Anomalies such as bullseyes and drift were not observed in the maps that were generated. Kriged maps showed the spatial distribution of quality continuity and variability of the deposits. Grade-tonnage curves and total tonnage estimates in the particular grade were determined using ordinary kriging in order to improve the mining operation and planning. Consequently, local uncertainty and the probability of extreme values occurring are tools of prime importance for the mine planning, the optimum mix of raw materials coming from different quarry stopes.

Jan 1, 2012

By Bruce Vandenberg, R. Frank Chiappetta, John Foley

Recent advances in solid-state, field portable, fast framing compact video camera systems and PC based frame capture hardware now allow blast imaging up to 1000 frames per second. Up to 4.1 seconds of data can be captured directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the MotionMeter system and compare these with the analogous aspects of film-based cameras and other systems. Of all blast monitoring systems and techniques available today, high-speed motion picture photography and videography still remain as the most valuable, stand alone, diagnostic techniques for troubleshooting and evaluating full scale blasts in the mining and explosives industries. High-speed image data, coupled with information obtained from other instrumentation systems, such as continuous velocity of detonation recorders, laser surveying systems, refraction and ground vibration recording seismographs, etc., can eliminate many assumptions about what actually took place in a blast. Thus, diagnostic confidence in evaluating both excellent and poorly designed blasts is increased, and optimum blast results, (which are application dependent), are achieved considerably faster when compared to the trial and error approach of relying on strictly the experience factor. Applications include developing site-specific blast designs, decay equations relating burden, burden velocity and explosive energy, determining ground response times, reducing coal damage, quantifying backbreak, evaluating the effectiveness of sternming, checking delay detonator firing times, evaluating air decks and for studying general dynamics. Motion analysis is performed with a 2D and 3D software package developed specifically for video analysis, but is also directly applicable to film analysis when using a digitizer. Dimensional controls, lens aberration, field set-ups and camera orientation are all automatically corrected for with matrix analysis.

Jan 1, 2000

By Tex M. Kubacki

In 2007, the University of Utah Seismograph Stations (UUSS) temporarily expanded its seismic monitoring network in Emery County, Utah, in response to the August 6 Crandall Canyon mine collapse that trapped six workers. In spite of this additional coverage, no seismic events were located in the area during a six-day period (gap) from August 8 to August 13. The Mine Safety and Health Administration (MSHA) ?Command Center Log Books? however, contain references to 16 instances of underground ?bumping? and ?bouncing? that occurred during the gap. When ground truth information provided by the log books is compared to the raw seismic data recorded by the UUSS network, the correlation offers insight into the chronology of mininginduced seismicity (MIS) in the aftermath of the collapse. The new research focuses on identifying and locating seismic events that occurred during the six-day gap using double-difference relocation techniques and correlating them with log book ground truth. Ten seismic events were identified in the vicinity of the mine during the six-day gap, ranging in magnitude from coda magnitude (MC) 0.5 to 1.4. Three of these events were amenable to location by double-difference techniques. The location of one of these events is directly confirmed by ground truth information from the log books. As a result of this new research, the accuracy of Crandall Canyon double-difference locations has been improved, and the number of events correlated with ground truth information has increased. The seismic events occurring in and around the collapsed area appear in two distinct sections of the mine?east and west of the center of collapse. It was originally reported that the post-collapse events occurred in episodic clusters. The first two episodes occurred to the east, followed in time by a cluster on the west, and then by a third episode on the east. With the addition of new events to the data set, this pattern is no longer as clear, although the events still occur in clusters. Only one MIS cluster was found to occur within the bounds of the minimum estimated collapse area (Pechmann et al., 2008).

Jan 1, 2012