Search Documents

By Leigh J. Wardle

This paper describes a numerical method for calculating the three¬-dimensional stresses and displacements induced by tabular excavations in a rock mass consisting of parallel layers of distinct material properties. The method is based on the superposition of numerical solutions for elementary displacement discontinuities in a parallel layered rock mass. The method can be used to analyse complicated excavation layouts such as those encountered in room-and-pillar or longwall mining. The method can automatically take into account the effect of the earth's surface. The method offers an economic and efficient solution to stress analysis problems which cannot be adequately modelled using two¬-dimensional methods and for which the expense of three-dimensional finite element or general boundary element analysis cannot be justified.

Jan 1, 1984

By M. R. Tek, L. K. Thomas, D. L. Katz

Threshold displacement pressures are needed to determine how much overpressure can be used in storing natural gas. An experimental technique for determining threshold pressures by displacing water with gas from samples saturated with water is presented. Threshold pressures for eight low permeability samples were measured. Threshold pressure data obtained in this work, plus data on higher permeability samples reported in the literature, are correlated with porosity, permeability, surface tension and formation resistivity factor. Mercury injection pressures also were measured and correlated with air-water threshold pressures. Threshold pressures were found to be independent of time. An aerial photograph of gas emerging from the top of a core shortly alter its threshold pressure has been exceeded shows that the gas bubbles are uniformly distributed across the face of the core. Channeling will occur, however, when an increased gas phase permeability is reached, A porous medium can be re resealed alter its threshold pressure has been reached, provided it has not been desaturated below a fixed saturation. Its new threshold pressure will be lower than when the sample is 100 percent saturated with water. INTRODUCTION The degree of overpressure in excess of the discovery pressure that a gas storage reservoir can withstand is determined by the ability of its caprock to contain gas, providing the pressure does not exceed the structural limit of the reservoir. The retention of gas in a reservoir by a caprock saturated with water is a result of the capillary forces acting at the gas water interface. Without the presence of water in a caprock, gas would leak out of the reservoir at a rate determined by the permeability of the caprock to gas. The ability of a caprock to contain gas is expressed in terms of its threshold displacement pressure, which is defined as the minimum pressure needed to initiate the displacement of a wetting phase by a nonwetting phase from a porous medium 100 percent saturated with the wetting phase. The gas industry must be able to predict how much "overpressure" a gas reservoir can withstand before leakage occurs by gas displacing water from caprock overlying the reservoir. This is of economic importance since the storage capacity of a gas reservoir is proportional to its pressure. The discovery pressure for most reservoirs is found between the upper and lower limits1 shown in Fig. 1. Discovery pressures in excess of their hydraulic pressure gradient are attributed to the compaction of an isolated shale formation by the overburden.2.3 The lower limit of 0.433 psi/ft corresponds to the weight of the overburden, the gradient of the rock itself. Somewhere between

Jan 1, 1969

By W. E. Roscoe, H. Agnerian

The contour method can be used to estimate the mineral resources of a mineralized body. It relies on geological interpretation and allows the geologist to determine the plunge of a mineralized ore shoot along the dipping plane of the mineralized body. The technique is best applied to estimate tonnage and average grade of relatively planar bodies, i.e., where the two dimensions of the mineralized body are much greater than the third dimension, such as Archean lode gold vein deposits or mantos of massive sulphide mineralization, based on exploration drilling. For these types of deposits, the contour method can provide a clear view of the “mineralization landscape” with “peaks” and “valleys” along the plane of the mineralized vein. The technique also reduces the “nugget effect” of local high values commonly present in gold deposits. With sufficient drill hole information, the contour method may be used to estimate the tonnage and average grade of individual blocks within a mineral deposit. General procedures for the contour method are described in this paper, along with examples and explanatory notes.

Jan 1, 2002

By B. A. Day

The traditional view taken of commodity prices is that they are cyclical, with strong demand boosting prices and attracting new suppliers. The resulting increased supply pushes prices down with consequent exit of the higher cost producers. And so the process repeats itself. Little attention is given to shifts in underlying global issues and their effect on the traditional process which is seen as being controlled by ?amorphous? market forces with producers profiting from the good times and trying to survive in the bad.. The questions posed are: does this still apply and will it apply into the future? What new factors are affecting the cycles? Can we expect to find the traditional commodity cycles repeated in the 21stcentury? Are producers powerless within the forces of the cycles? Forces likely to affect future commodity prices will be suggested, using gold, zinc, copper, tin and coal as case studies. The long-term downward trend in the real price of commodities is identified.

Jan 1, 2000

By Jimmy Rodríguez Las Heras

Durante la explotación de los niveles inferiores en la mina Yauliyacu, se generaron dudas sobre la ubicación de las concentraciones de esfuerzos y sus relaciones con los estallidos de roca. En este sentido, se instala un sistema microsísmico donde mediante el análisis de la microsismicidad se elaboró los estándares que permitieron reducir los incidentes por estallidos de roca presente, así como la frecuencia, magnitud y daños a las personas, y equipo e infraestructura de mina, debido a la energía liberada por los eventos microsísmicos. Por ello, el presente trabajo señala los beneficios del uso del sistema de análisis de microsismicidad como la actualización contínua de la zonificación minera de acuerdo a la concentración de esfuerzos, procediendo al reforzamiento del sostenimiento como medida de prevención.

Sep 21, 2013

The difficulty of accurately sampling cyanide gold bullion for valuation is well known, and nothing new or original is claimed in presenting this paper, but it was thought that a record of differences in the composition of bullion bars found here may be of interest to others, and perhaps helpful to those who have to do with theevaluation of cyanide bullion. This investigation was made after reading Mr. Sydney W. Smith's interesting paper on the Liquidation in Molten Alloys.*A method was in use of boring each ingot in two places and mixing the two borings for the sample. More accurate values were obtained, however, when the bullion was sampled in a molten condition immediately before casting into the ingot; the sample being so taken as to preclude oxidation of base metals before solidification of the sample.In all, samples from 32 ingots were assayed, and comparisons made between the existing boring sample and the proposed dip sample. Assays were also made of two other portions of the borings from each ingot, and the results show that in the majority of cases the borings sample assays higher in gold than the dip sample of the same ingot.The largest ingot cast weighs approximately 920 troy ounces, and has the dimensions shown in the attached sketch (Fig. 1). Ingots are cast in 0.1. moulds i in. thick, smoked and heated.METHOD OF TAKING BORING SAMPLES OF BULLION BARSThe bar is cleaned from adhering slag and drilled in two places only, to a depth of i-in., one hole on the top near one end and the other in the bottom at the opposite end of the bar.

Jan 1, 1931

By J Kelly, C Kelsey

The Autogenous Kelsey Axial Displacement (KAD) mill is essentially a short retention time centrifugal mill, designed to effectively harness extraordinarily high concentrations of input energy for efficient particle size reduction. The mill which has an operating duty band extending from primary to ultra-fine also has the unique capacity to generate fine and ultra-fine products from single stage size reductions of either coarse or fine mineral feeds, in both wet or dry operating modes. This paper covers developments following a recent optimisation programme which confirmed that mill shell speed and the velocity differential between the shell and the rotating internal disc assembly tips could be optimised in relation to specific energy for a given feed rate and feed size providing the product size remains constant. Subsequent test-work further demonstrated the versatility of the mill with duties ranging from the removal of surface contamination associated with heavy mineral concentrate particles to the production of premium ultra-fine talc, from a single stage of size reduction. Open circuit grinding of a rougher gravity concentrate to liberate gold ahead of leaching also highlighted the scope for the application of low cost KAD milling for a range of hydrometallurgical feed preparation duties, which involve fine and ultra-fine grinding.CITATION:Kelly, J and Kelsey, C, 2013. Advanced media-free fine and ultra-fine grinding - The Kelsey axial displacement mill, in Proceedings MetPlant 2013 , pp 152-161 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Sumner M. Anderson

Any discussion of outside support to Latin American mineral industries must concede at once the pre-eminent role of U. S. industry and business. American capital has developed the great copper resources of Chile and Peru, the lead-zinc of Peru and Mexico, the bauxite of Surinam and Jamaica, the petroleum and iron ore of Venezuela. American consumers have provided the market for their products. U. S. companies operating south of the border have trained Latin American geologists, engineers, chemists, and skilled labor—including metal, mineral, and fuel technicians—to new and greater competence. The industrial demands of World War II drastically altered world economics and concepts of U. S. foreign mineral requirements. In this country discovery of vital mineral resources fell far behind the alarming depletion rates, and there was new appreciation of the actual and potential importance of the world's less extensively explored areas. During the war and afterward, the task of supplying the nation's mineral requirements became greater than private industry could carry alone, and the Government assumed a position of continuing support. In Latin America, as elsewhere, this support applies in three categories: banking, procurement, and technical assistance. The first two are now generally accepted as necessary Government functions; the third has often been misunderstood and misinterpreted, although it has given rise to legitimate controversy. There have been major accomplishments in all three categories, as well as some errors of judgment. Since the beginning of World War 11, U. S. Government financing, procurement, and technical assistance have been applied on a large scale to a wide range of commodities and services throughout the free world. The present discussion—under the separate headings mentioned—will concern only the support related to a single industrial group in a single geographic area. During the War Federal banking was conducted on an emergency scale by temporary agencies created to meet the abnormal circumstances. Unfortunately, there are no readily available data on these activities that would permit evaluating loans and credits extended for mineral projects in Latin America. The only agency operating in this field since World War II is the Export-Import Bank, under its own authority and to some extent from credits authorized by the Office of Defense Mobilization. The Bank can offer more capital—on more favorable terms—than is available from most Latin American banks, and its staff of engineers evidently can appraise loan applications more favorably than commercial banks in this country are willing to do. The risks seem to be justified, as defaults have been well under 1 pct of total loans. From V-J day 1945 to the end of 1957, mineral loans to Latin America have been authorized for projects totaling $541.63 million in eight countries. In order of magnitude of credits, they have been made to Brazil, Peru, Chile, Mexico, Argentina, Venezuela, Guatemala, and Bolivia. In order of magnitude by industries. they are for development and expansion of steel mills, copper, manganese, nitrate plants, iron ore, zinc plants, sulfur plants, cement plants, tungsten, coal, and lead. Loan Distribution: By far the largest loans have been $307.9 million for iron and steel projects in Brazil, Chile, Mexico, Argentina, and Peru: $100.4 for developing the great low-grade copper deposits of southern Peru; and $55.3 million for developing manganese deposits in the Territory of Amapa, Brazil. Others range from $20.8 million for a zinc smelter in central Peru to $19 thousand for iron-mine trucking equipment in Chile. It has been noted that 59 pct of the loans have been to foreign companies, 14 pct to companies of mixed foreign and American capital, and 27 pct to American mining companies. About 40 pct of the total authorizations has been disbursed so far. In addition to these amounts, the Strategic Materials Division of the Economic Cooperation Admin-

Jan 1, 1959

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

This paper gives a general description of mining operations at the Mount Morgan Open Cut. Certain features such as blast hole diamond drilling, which may be of particular interest, have been described in detail. The paper is covered by the following headings:-1. History2. Ore Reserves and Production Data3. Mining Methodsa. Design and Layout of the Open Cut.b. Overburden and Ore Breaking.c. Loading and Transport of Ore and Overburden.d. Transport of Men and Supplies.e. Survey and Assay.f. Drainage.4. Power and Compressed Air5. Mining Equipmenta. Shovels.b. Mine Transport.c. Dozer Tractors.d. Drill Shop.6. CostsHISTORYIn order to appreciate fully the design of the present Open Cut at Mount Morgan, a brief outline of the Mine's history and past mining methods is necessary. In 1882 the Mount Morgan Syndicate began to mine this large gold-copper orebody by small hill-top quarries...

Jan 1, 1952

By L. K. Barker

The purpose of this research was to determine how much, if any, improvement would be made by subjecting hydrogenated shale-oil naphtha to a catalytic reforming process. Preselected ranges of temperature and pressure within the commercial reforming ranges were chosen for investigation and other possible variables were held constant. All tests were made with a liquid hourly space velocity (LHSV) of 3 volumes of liquid feed per volume of catalyst per hour (Vf/Vc/hr) and a hydrogen feed rate of 3,000 scf/bbl. Operating temperatures of 850°,875°, and 900° F were used at pressures of 200,400, and 600 psig. The greatest octane improvement in the naphtha was obtained at a temperature of 900° F and pressure of 200 psig. The reformed naphtha had a clear research octane number of 89, a liquid yield of 80 vol pct, and a yield-octane number of 71.1. The data indicate that a higher temperature could have produced a higher yield-octane number.

Jan 1, 1973

By Gregory Molinda

Historically, coal miners have known that roof shales can deteriorate in contact with humid mine air, causing massive roof falls and injuries from falling rock. It is critical to recognize rocks prone to weathering and to adequately support these rocks in order to ensure the long-term stability of the openings. In a recent study, NIOSH has used a wet/dry cycling test to determine the moisture sensitivity of over 800 specimens of roof rock from 25 U.S. coal mines. Fireclays and some gray shales are the most moisture-sensitive. Rocks with disturbed bedding, in contrast to flat-bedded rocks, are also more sensitive to water. Black shales are relatively un-reactive to moisture and serve to protect more reactive gray shales above. Mines that have roof rocks with moisture-sensitivity indexes above 40% can experience slaking roof conditions, and many require high coverage surface controls. Three case studies are presented in which the moisture-sensitivity index is correlated to roof conditions underground, and can be used to indicate long term deterioration. Engineering measures are described to control moisture-sensitive roof. In one case, roof screen not only reduces injuries from rock fall but also is shown to reduce roof falls. Keywords: coal mining, roof control, slaking, roof support, rock falls

Jan 1, 2008

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermophysical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous cases is modeled with walls, each having a different set of thermophysical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

A modified liquation technique was developed for recovering tin from tinhouse scruff metal or hardhead containing about 10 per cent iron and 15 per cent occluded flux, palm oil, and moisture. This was effectedby heating the scruff metal to 950°C followed by rapid cooling to suppress the formation of FeSn2 and FeSn, and then subjecting it to the ordinary liquation and drossing processes of refining. By this method it was possible to recover about 83 per cent of the original tin content and, with subsequent smelting of the irony drosses, an overall recovery of 92 per cent was obtained.

Jan 1, 1969

By Holly J

The period following World War II has seen many changes in stoping techniques at The Great Boulder Gold Mine. The new methods resulted in improved unit production figures, and have given some relief from the rising worldwide cost spiral in the post war years.Significant production figures are shown graphically in...

Jan 1, 1956

A BRIEF DESCRIPTION OF TELPHER HANDLING AND BLAST FURNACE EQUIPMENT.The various sections will be described in the following order:(a) Telpher Handling and Storage Bins.(b) Blast Furnaces.(c) Slag Disposal.(d) Bullion Handling to Drossing Kettles.(e) Copper Drossing.(f) Copper Matte Furnace.(g) Bullion Delivery to Refinery.(h) Fume Handling.(a) TELPHER HANDLING.The telpher installation is an all-steel structure designed to carry out the work of assembly and delivery of charge materials to the blast furnaces.To simplify description, the primary telpher installation will be divided into three (3) sections:-No. 1 Section. 395 ft. long, running north and south, parallel to the water front, and so located that coke, which...

Jan 1, 1937

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

The history of zinc production in Australia is outlined including attempts to make zinc electrolytically at Cockle Creek, N.S.W. in the last century, the use of horizontal retorts at Cockle Creek and Port Pirie, South Australia, production by electrolysis at Risdon, Tasmania and at Port Pirie using zinc oxide fumed from lead blast furnace slag and production by the Imperial Smelting process at Cockle Creek. Developments in the electrolytic process are described including those in roasting, acid manufacture, leaching, purification, electrolysis, melting and casting. The Imperial Smelting process technology is also outlined. In both processes global technology is reviewed, including important Australian contributions.

Jan 1, 1986

By Jinhui Li

Silver is a very important metal used in a wide range of applications. It is necessary to recovery of Ag from electronic wastes for increasing of Ag price and circumstance protection. For separating and recycling Ag from Ag-Cu composite materials, thermodynamic data of reaction is calculated and some experiments have been proceeded with Ag-Cu composite material scraps, time, temperature, nitric-sulfuric mixed acid volume ratio and the volume ration of mixed acid vs. water have been discussed. The results show that the optimization conditions is that nitric-sulfuric mixed acid volume ratio 5:95, volume ratio of mixed acid vs. water 10:1, temperature 55?, time 25min. In the conditions, Ag can be selectively leached from Cu-based composite material, Cu base is not eroded nearly.

Jan 1, 2009

By R. F. Rolsten

VAN Arkel 1 prepared ductile tantalum by the thermal decompoiition of tantalum pentachloride on a resistively heated wire (2000° C) in an evacuated bulb maintained at 100°C. Burgers and Basart2'3 observed the formation of a mixture of tantalum carbide and free metal when a carbon deposition base was used. campbel14 suggested the thermal decomposition of the iodide if a lower decomposition tem- perature was desired. To date, the details for preparing high-purity iodide tantalum have not been disclosed. EXPERIMENTAL The tantalum to be purified was symmetrically placed around the clear quartz deposition surface centrally located within a 64 mm cylindrical Vycor bulb. The deposition vessel usually employed5 was modified6 by incorporating a reentrant fin,mer in place of the customary metal filament in the head

Jan 1, 1960