Search Documents

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

The projection of operating costs for mining, processing, and other site operating costs is an exercise which can be fraught with considerable peril. Not only are the physical characteristics of each mineral property unique, but a range of other factors will influence the consultant's approach to compiling cash flow estimates. This paper details some of the techniques used in estimating operating costs for use in order-of-magnitude cost studies and feasibility studies, and describes how to avoid common areas of difficulty. A series of examples relating to open pit gold mining and processing cost estimates illustrate these problems, and various corrective methods are described. The mining and treatment processes, and their associated cost elements, are followed in sequence of operation from on-going ore delineation through to disposal of the product. In addition the problem of assigning management, administration and overhead costs along with taxation allowances is addressed. Of critical importance is the application or possible misapplication of accrual procedures to the cost elements. In many cases such misapplication can introduce more pronounced errors with projects of short duration, such as the typical open pit/C.I.P. gold operation commenced in the last decade. The importance of providing verification of estimates depending upon the standard of the cost study is also investigated, and opinion is provided upon the minimum levels of verification necessary at various stages. Finally, the amalgamation of the various individual cost elements into a coherent whole is reviewed.

Jan 1, 1990

By Dimitrios Litsas, Michael Kavvadas, Panagiotis Sitarenios

"The paper discusses the results of 3D finite element analyses to investigate the effect of face support pressure and soil permeability on face stability conditions in EPB tunnelling. Two main types of face behavior are identified: Undrained conditions ahead of the tunnel face, typically occurring in soils with permeability less than about k=5·10-7m/s, are shown to be favourable for face stability; analyses show that an applied face pressure comparable with the initial hydrostatic pore pressure is sufficient for adequate face stability, even for soils of relatively low strength. Drained or partially conditions, typically occurring in soils with permeability higher than about k=5·10-6m/s, show that face stability is strongly dependent on the horizontal effective stress of the muck in the excavation chamber; the presence of even a small effective stress in the muck is very beneficial for face stability conditions and can be a possible explanation of successful EPB tunnelling through relatively permeable soils. INTRODUCTION Face stability is probably the most important aspect in urban tunnelling. Usually, Earth Pressure Balance (EPB) machines are utilized, to ensure that a reasonable amount of face pressure is exerted on the advancing excavation face, reducing ground loss and preventing potential instability of the face core, thus controlling the amount of disturbance caused by tunnel excavation to surface structures. However, the ideal amount of face pressure depends on several factors (ground and groundwater conditions, tunnel size and depth, muck conditioning, etc.) which are difficult to include in analytical calculations. For many years, conventional empirical or analytical methods (e.g. Anagnostou & Kovari 1996) were the only available tools for quantifying face stability and selecting the required face pressure. In the last few years, however, numerical analyses have gained power over conventional methods, allowing more accurate designs and providing useful information about the anticipated ground deformations due to tunnelling. Numerical analyses have also been used in assessing safety against face instability using face extrusion (horizontal face displacement) calculations (e.g. Prountzopoulos 2012)."

Jan 1, 2016

By F. Mendaña

The characteristics of the igneous and metamorphic bedrock, extra-hard and abrasive, of the Guadarrama Tunnels, a bi-tube project of length 28.4 km without any intermediate attack, are first commented upon. Next, a detailed discussion is given of the most relevant aspects of the performance of the four double shield type TBMs. The experience of this leads to various recommendations to be borne in mind in future designs of TBM having to work in rock of similar characteristics.

Jan 1, 2007

By Joseph L. Condon

Fifteen shots of three explosives with charge weights of 0.52, 1.1, 3.1, and 5.1 kilograms were fired in a pond to study the seismic effects of detonating explosives in water. Shock pressures and bubble periods were measured with pressure transducers in the water. Vibrations were measured on land in three orthogonal directions with particle velocity gages. Statistical tests indicated that a charge weight exponent of 0.43 best scaled the data. While shock pressures and bubble periods showed considerable differences in explosive performances, the amplitudes of ground vibrations showed less difference, and one prediction equation was therefore derived to estimate vibration amplitudes from all the explosives.

Jan 1, 1970

By Fathi Habashi

While it is commonly known that the precious metals and to some extent copper occur in the native state, it is less known that mercury, iron, nickel, and cobalt do occur also in the native state; the last three (Fe, Ni, and Co) usually occur together in form of an alloy. The particle size varies greatly from less than 10 microns (gold and mercury) to about 400 tons boulders (copper).

Jan 1, 1993

By J Fut=

The rotary drilling of rocks is widespread technology in mining and in tunnelling. The paper describes the results of research by aim to find relationships between optimal drilling and sound signal of drilling machine. The optimisation criterion has been formulated as the minimisation of specific energy with maximal effective speed of drilling in process of the rock disintegration. The research in this field has been made on experimental drilling stand. Our monitoring system has measured following variables: the pressing force of core drill, the revolutions of drilling head, the length of drilling, the time, the power, and the acoustic signals. For measurement of acoustic signals have been used very sensitively sound meter MEDIATOR 2238. From this measurements have been processed acoustic spectrums. Then we are found relationships between optimal control of drilling and composition of acoustic spectrum. On base of experimental results, we can formulate the optimal control following: æTo achieve the minimum difference between the equivalent sound level at the load and idle modes only at the representative frequency (f = 1000 Hz)Æ. The representative frequency dependences on type of the rock New method based on these relationships enables the optimal control of drilling machine by using measured acoustic signals only.

Jan 1, 2003

By Martin Plante, Denis Hamel, Marie-Pier Bédard, Jeff McLaughlin

"The results and methodology for the optimisation of the zinc flotation circuit at the Matagami Mill using the 6-Sigma methodology are shown in detail while only the base line and final results are presented for the copper circuit. As a result of the six sigma project, the zinc concentrate grade was improved by 2% and the zinc recovery by 3%, with reduced dosage of reagents while the copper concentrate was improved by 2.4%. The process variation in the zinc concentrate grade and recovery was also reduced by over 50%. The main factors contributing to the project success were identified to be improvement in the plant measurement systems, an internal benchmarking exercise and statistically designed laboratory and in plant tests to guide the process improvement. The annual value to Noranda resulting from this project has been estimated at approximately $5 million.INTRODUCTIONThe Matagami concentrator started ore processing from the new Bell- Allard deposit in July 1999. Concentrator performance (grade and recovery of zinc and copper concentrates) was highly variable and work was ongoing to fix the sources of variation. In the mean time, Noranda embarked on its 6-Sigma initiative across the company. The 6-Sigma DMAIC (Define, Measure, Analyse, Improve, Control) methodology was used in the two flotation circuits to reduce variation and improve performance. The statistical 6-Sigma methodology moves towards identifying and controlling critical process operating variables (the X' s) to achieve customerspecified performance (the Y's). The goal of the methodology is to describe a process in a numerical equation known as the transfer function, given as Y = f (XI, X2, X3.. .), where Y could be concentrate grade or recovery and examples of X's are reagent dosage, particle size, etc. With the transfer function, optimal operating conditions and control tolerances are established for the key X's to ensure the desired Y performance is obtained.Each phase of the 6-Sigma methodology is explained below with examples from the Matagami project."

Jan 1, 2001

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9 ), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By Karsten Zimmermann

Surface deformation monitoring is required all over the mining industry. For example oil and gas companies need this information to support exploration and production activities and to detect impacts from surface subsidence of existing hydrocarbon fields. Also opencast mines require large area information of subsidence due to dewatering of the overburden. Because of this, a lot of surface deformations measurements with GPS or traditional geodetic measurement techniques have been conduced during the last decades. This paper presents the actual capabilities to analyze GPS data using the state of the art Bernese GPS Software for GPS post processing. A new way of monitoring subsidence is a combination of GPS and satellite InSAR data. Considering this it is hoped that a combined strategy will permit receiving overall more information by integrating high point density of InSAR and accuracy of GPS. DMT is one of the leading actors on GPS services especially for monitoring surface movements from underground activities e.g. mining, water pumping or oil and gas exploitation. The paper will discuss preferences and problems of this approach on results of a current project of DMT.

Jan 1, 2008

By Rowan A' Murry Karstel

One way to ensure dragline productivity is by Increasing the size of the dragline bucket. In August 1994, Optimum Colliery in conjunction with Van Reenen Steel, Northwest Applied Technology, SSAB of Sweden and Barlows Equipment launched the new lightweight dragline buckets. Optimum built the first prototype bucket that was used for the deslgn for future buckets. After knowledge had been gained from measuring the input force of the bucket Northwest Technologies designed the new bucket with finite element analysis. Together with the knowledge of quenched and tempered steel from SSAB of Sweden and Barlow Equipment, the new Wrightech bucket was born.

Jan 1, 1998

By Peter Metcalfe

"Wireless communication in the mineral processing environment is not as simple as it is in the home or office environment. The correct design of a wireless network in the mineral processing environment can offer a more flexible and lower cost installation than the transitional fiber networks. However with the flexibility of a wireless solution, also comes some limitations. By reviewing the plant requirements along with weighting the wireless benefits and limitations it is possible to design a network that combines the robustness of a wired solution with the mobility of a wireless solution. This paper addresses some wireless design considerations and it looks at some real life examples in the following areas: •,Meshed wireless network for high levels of redundancy •,Wireless instruments (such as HART, Modbus and others) •,Portable devices for mobile operators •,Network monitoring for plant personnel (it’s no longer just for IT people) INTRODUCTION Typical networks used in the mineral processing environment consist of a fiber network infrastructure with industrial switches used to connect the network devices. These fiber networks can be redundant or put into a ring topologies to offer a higher level of availability. Fiber networks have the benefits of: •,Immunity to noise from power and grounding issues •,Ability to span long distances (2km for multimode fiber and 20km for single mode fiber) •,Maintainable “off-the-shelf” technology Fiber networks however have some drawbacks, such as: •,Relativity high initial installation cost for cable trays, poles, trenches and pulling and termination of cable. •,Fixed geographic topology, adding future fiber drops may be challenging and expensive. •,Mobile users are not considered. Integrating a wireless network with a fiber network can offer the best of two worlds, a reliable high speed backbone for mission critical activities and a wireless network for remote applications and mobile users."

Jan 1, 2014

By T. D. Parris

Within a 30-mile radius of Sudbury, Ontario, the Ontario division of the International Nickel Co. of Canada, Ltd., operates nine underground mines and two open pits. Prior to 1966, ore removal from the underground workings was mainly by scraping, using 125-hp electric slushers in blasthole and caving mining, and 30-hp or less air-operated slushers for fill- method mining. The development and evaluation of low-profile, diesel-powered front-end loaders, designed specifically for underground operations, was followed with keen interest during the period 1964-1965.

Jan 6, 1969

By Dave Marsh, John Goode, Niels Verbaan, Kevin Bradley, Henrie Notzl

The mineralogy of the Avalon Nechalacho deposit is complex with significant fractions of HREEs, Zr, and Nb found in refractory minerals such as zircon and fergusonite. Sulphuric acid baking followed by water leaching can be used to extract REEs from flotation concentrates, but acid baking does not completely "crack" the zircon and fergusonite, so the extractions of Zr, Nb, and HREEs are not high. An alternative flowsheet has been developed that is able to obtain significantly improved extractions of HREEs, Zr, and Nb from flotation concentrates or acid bake residues. This is accomplished by cracking the zircon and fergusonite minerals with caustic soda at high temperatures, followed by water washing to recover excess caustic soda and soluble sodium silicates and phosphates. REEs, Zr, and Nb in the solid residue can then be solubilized with HCl or H2SO4. This paper highlights some of the findings from an extensive laboratory program and discusses several flowsheet implications.

Jan 1, 2014

By J. D. Miller

Characterization of feed material with respect to expected concentrate grade and recovery is fundamental to the design of improved separation efficiencies and to achieve sustainable development in the utilization of our mineral resources. An important reference point for this characterization is the liberation-limited grade/recovery curve which represents the perfect separation, the best separation which can be achieved for a given feed material limited only by the extent of liberation. Now, liberation-limited grade/recovery curves can be determined based on 3D mineral liberation analysis of feed material. Thus, actual separation efficiencies can be compared to what might be expected for a perfect separation limited only by the extent of liberation. It is shown that 3D mineral liberation analysis based on X-ray micro CT (XMCT) is preferred to 2D section analysis which overestimates the extent of liberation. By way of example, procedures and experimental results are presented and discussed for feed material in the case of phosphate rock flotation.

Jan 1, 2009

By A. Yu. Lein, V. V. Maslennikov, S. P. Maslennikova, I. Y. u. Melekestseva, Yu. A. Bogdanov

Tellurium is a high-tech and also toxic element. This element shows sufficient contents in Fe-Mn crusts and nodules in the modern ocean to be involved in future industrial processes [Hein et al., 2003]. Tellurium minerals and contents are not well recorded in modern and ancient black smoker systems. Tellurides are rarely found in sulfides from the modern oceans [Iizasa et al. 1992; Maslennikov et al., 2010]. The previous common opinion that tellurium is scarce in active seafloor hydrothermal systems can be revised due to the recent discovery of abundant tellurides in chimneys from Brothers Volcano vent site [Berkenbosch et al., 2012]. We found abundant tellurobismuthite, hessite, and native tellurium in chimneys from Su Su Knoll vents sites (West Pacific). So, tellurides can be found in some chimneys but absent in others. The causes of this are poorly understood. These conflicting data create numerous questions and require an explanation. The problem can be resolved by research at different scales including analysis of relevant genetic features of host sequences, systematic textural and paragenetic studies of different types of chimneys, and their rare mineral assemblages. Paragenetic models, compositional analyses and ranges of tellurium-bearing minerals and the physicochemical interpretation of chimney diversity in different types of VMS deposits are the main subjects of our research. The data on tellurides in chimneys from ancient VMS deposits should also be useful to resolve this problem.

Sep 1, 2014

By L. Rademeyer, P. Mazzoni, C. Kubank, F. Brown

The Corridor Sands deposits of heavy mineral sands represent the largest known economic resource of titanium dioxide minerals. The West Block of Deposit 1 alone contains Measured and Indicated Mineral Resources of 1.7 billion tonnes containing 4.14 per cent ilmenite, estimated in accordance with the JORC standard, sufficient for at least the first 20 years of mining. Total mineral resources are estimated to be approximately 17 billion tonnes at 5 per cent Total Heavy Minerals (THM). Test work was undertaken on the West Block of Deposit 1 over a period of two years in order to develop the process flow sheet to bankable standards. Geological, mineralogical and metallurgical test work was integrated from a pre-feasibility stage to the full bankable stage. The process flowsheet was developed with the central objective of the production of saleable products, of consistent quality and acceptable to the respective end-markets. The aim of this paper is to describe the way in which the various challenges for the project have been addressed by using integrated geological and mineralogical information, which has resulted in the development of a complete flow sheet. The process confirmed that material within customer specifications could be produced, once various metallurgical parameters were understood. This flow sheet development progressed from laboratory test work through to full field trials at pilot plant scale on large consignments of mineralized material. The flow sheet was developed to such a standard as to be used with confidence for both engineering design and cost estimates, and to determine the recovery factors to be used in financial evaluations. Keywords: Corridor sands, Flow sheet, Pilot plant Titanium dioxide

Jan 1, 2003

"7.1. Glossary of the Platinum-Group Minerals7.1.1. IntroductionA glossary of the platinum-group minerals (POM) serves as a useful introduction to a chapter on their mineralogy. Earlier glossaries (Cabri, 1972, 1976) were prepared for different purposes and composed in a different manner. As for most mineralogical textbooks, from Dana's System of Mineralogy, 3rd Edition (1850) , to Fleischer's Glossary of Mineral Species (1980), this glossary is primarily a chemical classification, arranged here in two tables. Table 7.1 groups the mineralforming compounds of the six platinum-group elements (POE) according to their essential anion(s) or according to the nonPOE element in intermetallic compounds. Table 7.2 is a similar listing for the native metals and alloys of the POE. Both tables include unidentified POM considered to be bona fide new minerals requiring additional study for complete characterization and recognition (see Chapter 9*). Some information on the chemistry of the POM is given in the sections on X-ray data (7 .2) and ore microscopy (7 .3). Because the overwhelming majority of POM have been characterized by the electron microprobe, a more detailed account of representative analyses is given in Chapter 8**. The total POM listed in Tables 7.1 and 7.2 is about 100, after deleting some which would not qualify as discrete species if found today, but which are still recognized on historical grounds; e.g. iridosmine, osmiridium, platiniridium. Tables 7.1 and 7.2 also include 28 unnamed POM; included because they are considered to be probably new species (Cabri 1981 b). The referral scheme for unnamed minerals is the same as in Chapter 9. There are considerably more palladium minerals known than other POM; the proportion of total species (listed in Tables 7.1 and 7 .2) for the POE is: Pd 48%, Pt 21 o/o , Ru and Ir 9% each, Rh 8% and Os 5%. These proportions are in marked contrast to the estimated cosmic abundance, as compiled for average type C1 chondrite by Naldrett and Duke (1980): Pt 29%, Ru 20%, Pd, Ir and Os 15% each, and Rh 6%."

Jan 1, 1979

In 1953, Dr. N. H. Fisher of the Bureau of Mineral Resources, acting on behalf of the Society of Economic Geologists, which is considering the sponsoring of a uniform system of nomenclature for ore reserves, enquired from the Australasian Institute of Mining and Metallurgy whether it had ever considered this subject and particularly whether it had ever set up any standard definitions or specifications with regard to ore reserves.As this had not been done, but was thought to be desirable, the Council of the Institute appointed a Committee consisting of H. H. Dunkin, Associate, Professor of Mining Engineering, University of Melbourne (Convenor), E. A. Rudd, Professor of Economic Geology, University of Adelaide, I. N. Campbell, Chief Geologist of Western Mining Corporation; and the writer to consider and report on this supject.In December 1953, the Committee submitted its first report to the council and this report (reproduced here as an Appendix) was widely circulated among member companies, and engineers, with an invitation to comment on the proposal. A large number of, replies was received and studied.After studying the replies the Committee issued a second report in part as follows:-From these replies we have learned that the suggestions made in the first teport of the Committee are unacceptable to most of those interested, on one or all, of the following grounds;-(a) number of categories,(b) definition of categories;(c) nomenclature.

Jan 1, 1955

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003