Search Documents

"The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are:1. Line Drilling2. Cushion Blasting3. Smooth Wall Blasting4. Buffer Blasting5. Presplitting or Preshearing6. Air Deck Presplitting"

Jan 1, 1994

By Richard F. Sliwoski

The Virginia State Capitol was designed by Thomas Jefferson and constructed in 1785. The Capitol is of great historic and architectural significance to not only the Commonwealth of Virginia but to the nation. It is the oldest operating Capitol in the U.S. and required a total restoration/renovation as well as an expansion to continue to remain functional. Site conditions dictated that the expansion (a new visitor center) be placed underground on the south side of the Capitol building, requiring a 40-foot deep excavation approximately 5 feet from the Building. Because of its historic significance, every measure had to be taken to ensure the safety and function of the Capitol during construction. The construction techniques that were used to make the deep excavation and protect the historic Capitol included a tied back concrete slurry wall, jet grouting, compensation grouting, and instrumentation monitoring. This paper describes the history of the Capitol building, the techniques that were employed for construction of the deep excavation, results of the latest movement monitoring, and factors contributing to meeting the restrictive movement goals.

Jan 1, 2006

By Y. Sasseville

"Niobec has been using vibrating screens and screw classifiers as a double stage classification in its grinding circuit since the very beginning of its operation in St-Honoré. Most of the other mineral processing plants around the world uses cyclones as the classification device in their grinding circuit. The difference between these two methods are well known in terms of capital cost and grinding efficiency but the differences in terms of the impact on the downstream processing stages are a lot harder to predict and are case specific. In the interest of lowering the capital cost of a future expansion project, Niobec decided to test the cyclones in its actual grinding circuit and evaluate their impact on the recovery of the downstream processing stages as well as the operating cost of the mill. We switched between cyclones and screens for 8 month in 2013 and early 2014 and we are now operating only with cyclones since march 2014.INTRODUCTIONThe Niobec mine and concentrator were built in the mid 70’s and at that time, the mill was processing 1 500 tons per day. Over the years, many expansion projects have brought the plant to 7 000 tons per day. Throughout the initial concentrator design and commissioning, screens have been chosen over cyclones because of their higher classification efficiency which is known to reduce variability and limit the fine generation especially due to a high undersize classification efficiency. Just like many other plants, fine particle generation is a major problem at Niobec because of its negative effect on downstream processing stages. In the interest of lowering the capital cost of a future expansion project, Niobec’s engineering team decided, 35 years later, to test the cyclones in its actual grinding circuit and evaluate their actual impact on the final recovery and the operating cost of the mill.The grinding circuit is separated in two lines which will be called Circuit #1 and Circuit #2 along this paper. Circuit #1 is, as you can see in Figure 1, composed of a rod mill and two parallel ball mills in closed circuit with screens and screw classifiers. The screens oversize are sent to the screw classifiers while the undersize are sent to the next processing stage. The screw classifiers overflow are both sent back to the pump box while their oversize streams return in their corresponding ball mills for further grinding. Circuit #2 is, as you can see in Figure 1, quite the same as Circuit #1 except it has only one set of screw classifier and ball mill. Figure 1 also shows the modification in arrangement each circuits went through to integrate the new cyclones. One of the ball mills in Circuit #1 now appears dotted because it can still be used but is not now"

Jan 1, 2015

By P L. McCarthy

To design and operate a successful mine the technical specialists must agree on what is ore, what is not ore, and how quickly the orebody is to be mined and processed. These seemingly simple questions defy easy analysis and can push mining engineers, geologists, metallurgists and others to the limit of their capabilities. The questions are rarely addressed adequately in feasibility studies or in operational planning. To optimise the mine and processing plant requires proper determination of cut-off grades or values, prediction of feed variability on an hourly, daily or longer basis, right-sizing the mining rate for optimum product quality, understanding the cost of capital and the expectations of investors, and many other considerations that involve geology, geotechnical engineering, mining, metallurgy, environmental effects and economics. This paper addresses the key matters that should be considered as inputs to the practical issues of metallurgical plant design and operation.CITATION:McCarthy, P L, 2015. Integrated mining and metallurgical planning and operation, in Proceedings MetPlant 2015, pp 35–45 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Martin Herrenknecht

After the successful breakthrough at the end of 2006 of both TBMs into the multifunctional site Faido (MFS), in the middle of 2007 the two tunnel boring machines resumed the 12 km long section between Faido and Sedrun. In the roughly a 10 month interval both approximately 465 m long tunnel boring machines were partly dismantled, pushed through the 2.5 km long MFS, rebuilt for the new larger diameter of 9.5 m and reassembled to be ready for operation. In the rebuilding phase, improvements were made to the equipment, especially as a result of experience gained from the previous 14 km long drive in the section Bodio and taking into account the latest information regarding the upcoming 14 km section Faido. Both TBM drives are currently in the rock formations of the Lucomagno gneiss, which stretch over a section of 3.5 km from the MFS Faido to the predicted Piora Syncline. This section is divided into two fold axes of the Chièra Synform, where the Lucomagno gneiss pass from a sub-horizontal into vertical bedding. The drives, with current rock overburdens exceeding 1,500 m and, as known from the excavation phase of the MFS, in part highly disturbed rock formations, are characterized by the locally intense rock squeezing conditions with large convergences in the vicinity of the driving TBM as well as backwards due to the interaction of the two drives. High expenditure for the support measures, reduced driving performances together with extensive extra work associated with deadlines and increased costs are the result. In the paper the previous experience with the TBM drives in the section Faido and the challenges still awaiting us are presented and discussed.

Caving of the second lift of the E26 orebody at Northparkes Mines was monitored with a comprehensive package of instrumentation, including an ISS seismic monitoring system. Seismicity was collected by an array of 19 triaxial accelerometers and 9 uniaxial geophones, giving a high quality seismic data set. The seismic response to block caving at Northparkes has been divided into two papers. The first paper focuses on the seismicity during undercutting. The second paper deals primarily with the seismicity during cave propagation during initial cave production. In this paper, traditional seismic monitoring concepts are applied to seismicity during cave mining. More than 40 000 seismic events were recorded during cave undercutting between February and January 2004. Events up to local magnitude +1.3 were recorded near the mine during undercutting, with event rates of up to 500 per day. Analysis of frequency-magnitude distributions, S-wave to P-wave energy, and temporal variations in event magnitude all gave insight into the seismicity recorded. In addition, a new technique, called apparent stress time history, was shown to be sensitive to stress change from undercut blasting, and useful to identify significant periods during cave development. A significant difference was identified between the cave back location and the halo of seismic events above the cave. Throughout the undercutting, the a seismic zone of loosening was typically 50 to 70 metres in vertical thickness. Based on the seismicity, a stress driven rock mass failure model is proposed. Early in the undercutting, seismicity and movements in the seismogenic zone were directly triggered by stress change from undercutting. Towards the end of undercutting, seismicity was virtually uncorrelated with undercut blasting, and likely due to the onset of cave initiation.

Jan 1, 2008

By T. Deng

Flotation of rare earths is complicated by the number of mineral classes that carry rare earth elements, including carbonates, phosphates, and silicates that often co-occur within the same deposit. Gangue constituents often belong to the same mineral classes as the rare earth minerals themselves. Chemical regimes developed for specific separations employ customized combinations of collectors, modifiers, and depressants that are not directly translatable to other operations. In this rougher flotation case study, a reagent suite including phosphate ester and sulfosuccinamate, originally developed for the recovery of bastnasite and monazite from silicate hosted ore, could not be applied to a synchysite ore hosted in carbonate gangue because the suite was aimed at silicate gangue rejection only. The separation of a fluorocarbonate mineral from carbonate gangue required a different chemical regime involving the use of hydroxamate and sodium silicate. Maximizing rare earth recovery was complicated by the presence of slimes. The effect of desliming and the increase in grind size was explored.

Jan 1, 2014

By Herbert Clark Hoover, Lou Henry Hoover

As stated in the preface, the nomenclature to be adopted for weights and measures has presented great difficulty. Agricola uses, throughout, the Roman and the Romanized Greek scales, but in many cases he uses these terms merely as lingual equivalents for the .German quantities of his day. Moreover the classic language sometimes failed him, whereupon he coined new Latin terms adapted from the Roman scale, and thus added further confusion. We can, perhaps, make the matter dearer by an illustration of a case in weights. The Roman centumpondium, composed of zoo librae, the old German ceniner of 100 pfundt, and the English hundredweight of 1112 pounds can be called lingual equivalents. The first weighs about 494,600 Troy grains, the second 721,900, and the third 784,000. While the divisions of the centumpondium and the centner are the same, the Libra is divided into 12 unciae and the pfundt into 16 unizen, and in most places a summation of the units given proves that the author had in mind the Roman ratios. However, on p. 509 he makes the direct statement that the centumpondium weighs 146 librae, which would be about the correct weight if the centumpondium referred to was a ceniner. If we take an example such as " each centumpondium of lead contains one uncia of silver", and reduce it according to purely lingual equivalents, we should find that it runs 24.3 Troy ounces per short ton, on the basis of Roman values, and 18.25 ounces per short ton, on the basis of old German. If we were to translate these into English lingual equivalents of one ounce per hundredweight, then the value would be 17.9 ounces per short ton. [ ]

Jan 1, 1950

By Thomas M. Gurtowski

The New Pacific Northwest Baseball Park, now known as Safeco Field, is located directly south of the Kingdome in Seattle, Washington, and will be the new home of the Seattle Mariners baseball team. The location of the ball field is shown on Figure 1, Vicinity Map. The seating capacity is 45,600, and outfield distances are 331 feet in left, 405 feet in center, and 326 feet in right field. The overall dimensions of the stadium are 680 by 800 feet. It is bordered on the east by the Burlington Northern Santa Fe Railroad main line. A unique aspect of this ballpark is the retractable roof with a north-south span length of 660 feet. The roof consists of three separate sections that roll on elevated rails running east-west on the north and south sides of the stadium. The soil conditions consisted of near-surface fill underlain with alluvial and Estuarine deposits to depths of 60 to 80 feet. The bearing soils consisted of very dense, glacially overridden deposits. Groundwater is 4 to 7 feet below the ground surface, and the alluvial deposits are subject to liquefaction during a strong motion earthquake.

Jan 1, 1998

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By H. Venkatesh, Balachander R.

This article discusses the method that was adopted for controlling damage to rock mass while excavating an underground powerhouse cavern at Tala Hydroelectric Project. It discusses in detail the near field vibration studies carried out and the safe vibration levels established for that rock mass condition.

Jan 1, 2006

By P. C. Fletcher, E. Kaya

The Bond grindability testing procedure has been standardized to measure the same grindability values, i.e. Bond work index (BWi), for the same ore when tests are performed in different laboratories or by different operators. This is accomplished by the standardization of mill dimensions, tumbling speed, grinding ball charge weight and distribution, sample ore charge weight in the mill and operating practice. The results of this investigation reveal that the Bond work index grindability values may differ substantially with different standard Bond ball mills. This paper will review the results.

Jan 1, 2002

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By D. J. McLaws

"Recent innovations in metal smelting technology utilize continuous oxygen-enriched smelting and converting processes which are capable of producing off-gases containing up to 60% SO2 or more. Other SO2 recovery processes, involving solvent absorption and steam or vacuum regeneration, can produce off-gases with SO2 concentrations nearing 100%.Processing of these high-concentration SO2 off-gases in conventional sulfuric acid plants can cause excessively high catalyst bed temperatures and poor SO2 conversion. In order to avoid these problems, a conventional acid plant design must dilute these high SO2 process gasses with dilution air in order to provide the required oxygen to effectively convert the SO2 and provide a heat sink (via the inert N2) such that the exothermic reaction, SO2 + ½ O2 ???SO3, does not exceed the temperature limit of the catalyst or the converter vessel.MECS, Inc. (MECS) has proven that a high SO2 feed gas design can be a viable option which can increase energy recovery, reduce energy consumption and potentially reduce capital costs."

Jan 1, 2014

By Dr. Peter J. Conroy

The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to the DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. This paper summarizes the work that has been completed through September of 1981 and presents the results that have been achieved during this period. Technical difficulties encountered during both the installation and monitoring phases are discussed, and recommendations for future work are presented.

Jan 1, 1982

By Sam Bang Jr, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine’has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to sot? material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessaryas vertical presplit drilling produced wall failures.

Jan 1, 1998

By B S. Utting, W J. Cowie

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850s has been an estimated 480 t (15 Moz) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 t of gold for 1989. Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

By Ralph B. S

Bacterial leaching of low grade quartz felspar porphyry copper ore was studied in large-scale laboratory percolation leaching columns.Limitations in the release of soluble copper showed up before fifty per cent recovery, due to occluding precipitates of iron oxides and hydroxides. Precipitates were removed by increasing the acidity of irrigation feed four-fold with respect to sulphuric acid. However, irrigation at low pH (pH 1.5) inhibited copper leaching. Resumption of bacterial leaching at pH2 was achieved by introducing a period of non-irrigation. The results suggest a 'direct' attack by bacteria on the chalcopyrite substrate rather than an 'indirect' ferric-leach mechanism.

Jan 1, 1981

By Brad Wells, Wayne Bull, Wayne Dickinson

"Antiscalants were evaluated for control of calcium carbonate (CaCO3) in gold processing applications. Under severely supersaturated conditions, 100 percent inhibition was achieved with 30 ppm antiscalant. Laboratory and field testing established that an antiscalant could both inhibit scale buildup and remove an estimated 0.5 kg/m2 per annum of pre-existing scale. A program was developed to control CaCO3 at a gold mill experiencing severe scale buildup. Annual accumulation of as much as 3 cm of scale in process piping was reduced to unmeasureable levels when 10 ppm antiscalant was applied. No scale-related upsets in mill operation occurred during a five-month trial period.INTRODUCTION Inorganic mineral scale is a crystalline deposit that forms when dissolved mineral constituents exceed the solubility of the respective mineral phase. Formation of mineral scale adversely affects a wide range of industries and is of particular interest in mining and metals processing. Scale affects numerous stages of metal extraction processes. Restricted flow in piping, nozzles, valves, screens, pumps and other components used to transport mineral slurries, metal concentrates, and tailings as well as scale in millwater and thickener overflow circuits are primary concerns (Alfano & Boffardi, 1994). Heap leaching, comminuation, flotation, vat leaching, carbon adsorption, and heat exchangers as well as oxidation steps used in processing sulfidic ores are among key unit operations that may be adversely affected (Simmons & Gathje, 2003). Antiscalant chemicals are designed to prevent formation and growth of mineral scales such as CaCO3. These chemicals, which include two primary classes – phosphonates and anionic carboxylate polymers and copolymers - are added to the gold processing stream at low parts-per-million (ppm) concentrations to interfere with nucleation and growth of scale forming crystals and to disperse fine particulate material. Application points may be located throughout the gold extraction process. Evaluation of the performance of antiscalants plays a critical role in determining the best product for a specific application. Performance evaluations include laboratory testing, pilot scale studies, in-plant trials, and ongoing performance monitoring during mill operation."

Jan 1, 2014

The research described in this report was conducted under a cooperative research agreement between the U.S Bureau of Mines Twin Cities Research Center (TCRC), Cleveland-Cliffs Inc. (CCI), and three operations in Northern Michigan managed by CCI: the Empire and Tilden surface taconite mining operations, and the Central Shops maintenance facility. All of these operations are in or near Ishpeming, MI. The Human Factors Research Group at TCRC is responsible for designing, planning, and conducting the research, and reporting on the findings. This project was carried out in order to investigate the high prevalence of back injuries being experienced by workers employed at the three CCI Northern Michigan sites, In an analysis of Company accident records for workers employed at these sites, it was determined that back injury problems confronting the CCI sites mirror those confronting the entire mining industry.

Jan 1, 1994