Search Documents

By H. Fukushima, T. Ohgai, N. Baba

The electrodeposition behavior of Zn and the morphology of the deposited Zn were studied in electrowinning solutions containing polymer additives such as gelatin and polyethylene glycol (PEG). The cathode potential was shifted in a less noble direction and the polarization resistance for Zn deposition increased with increasing concentrations and molecular weights of both gelatin and PEG added to the electrolytic solutions. However, when the molecular weights of these additives exceeded about lxlO4, the cathode was depolarized and the polarization resistance for Zn deposition decreased with increasing molecular weight. The crystal grain size and the (002) orientation of the deposited Zn became smaller when the concentration and molecular weight of the additives increased, and the cathode was polarized.

Jan 1, 2000

By Mark Samonds

"Manufacturing processes which involve liquid to solid and solid state transformations in metals encompass a wide variety of physical phenomena. The past twenty years have seen a steady evolution in the complexity and scope of numerical models of these processes, beginning with thermal analyses without phase change. Recently, a few software packages have become available which have true multi-physics capabilities. This permits the treatment of thermal, fluids, stress, electromagnetic, chemical reaction and microstructure development aspects altogether in a fully coupled simulation. This paper will consider various aspects of these types of models.Coupled thermal and fluid flow analyses of continuous castings have been around for fifteen years. Coupled thermal and free surface fluid flow simulations of shape castings have been available for ten years, including view factor radiation models for investment castings. Only recently, however, have fully coupled thermal, fluid, and stress analyses become practical. This implies the reverse coupling of the mechanical deformations to the solution of the energy and momentum equations through modification to the interface heat transfer coefficients and the fluid domain geometry. This has been implemented with a combined eulerian-lagrangian finite element method. Appropriate mechanical constitutive models will also be discussed.Many types of defects need to be predicted in casting processes. Those related to stress include hot tearing, hot cracking, part distortion, and thermal fatigue in dies. Macroporosity, microporosity, and microsegregation are determined by the solidification behavior and microstructure development in a casting. In particular, microporosity is influenced by dissolved gases, the morphology of the mushy zone, the liquid to solid density change, and the local pressure conditions. Macrosegregation is caused by the partitioning of solutes during. solidification and subsequent thermo-solutal convection. An additional transport equation is required for each solute that is being tracked. Computational thermodynamics is being incorporated into these types of analyses to determine transformation temperatures, partition coefficients, densities, and enthalpies. In combination, the microstructure and microporosity models can frequently predict a variety of mechanical models, such as yield strength, tensile strength, and elongation."

Jan 1, 2001

By Xinli Wang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Byoung-Gon Kim

"The microwave dielectric properties of silicon dioxide at frequencies of 915 and 2450 MHz were characterized in the temperature range of 24 to approximately 1000 °C using the cavity perturbation technique. It is shown that the relative dielectric constant of silicon dioxide at both frequencies remains almost unchanged below 500 °C, above which there is a slight increase of 2%. The relative dielectric loss factor of silicon dioxide exhibits a strong temperature dependence above 500 °C and increases by approximately 7 and 5 times at 915 and 2450 MHz, respectively. The substantial increase in the relative dielectric loss factor is mainly attributed to the enhanced dielectric polarization and accelerated electrical transport in silicon dioxide at elevated temperatures.IntroductionSilicon dioxide (Si02) is usually considered a microwave transparent material due to its poor absorption capability at room temperature [1]. This characteristic has led to various applications of silicon dioxide in microwave processing of materials and communication. For instance, Si02 has been used to produce sample holders for microwave heating and substrates for electronic devices [2,3]. These applications generally require the material to withstand high temperatures under microwave irradiation. This indicates that microwave absorption capabilities of silicon dioxide at elevated temperatures are also important for its utilization.The microwave absorption capability of Si02 can be determined based on dielectric characterization (permittivity measurement) of the material at commonly used microwave frequencies, 915 and 2450 MHz, in a broad temperature range. To date, however, no detailed work on the dielectric properties (permittivity) of silicon dioxide at high temperatures has been reported. The present work is aimed to study the dielectric properties of silicon dioxide from room temperature to approximately 1000 °C at 915 and 2450 MHz. The results show that the permittivity of silicon dioxide has a strong temperature dependence above 500 °C, suggesting a substantial increase in its microwave absorption capability."

Jan 1, 2013

By Monteirom Sergio N., Romulo L. Loiola, Giulio R. Altoe, Noan Simonassi, Frederico M. Margem

"The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. Buriti fiber extracted from buriti palm tree (Mauritia flexuosa), presents some significant characteristic, but until now only few studies on buriti fiber were performed. This work aims to make the analysis of the tensile strength of epoxy composites reinforced with buriti fibers. This analysis was performed in fibers with diameters between 0.1 and 0.4 mm. Those fibers were incorporated into the epoxy matrix with volume fraction from 0 to 30%. The fiber diameters were measured by a profile projector. After fracture the specimens were analyzed by a SEM (scanning electron microscope).IntroductionNatural fibers with high amount of cellulose, also known as lignocellulosic fibers, have been used from primeval times of our civilization. In the last century, synthetic fibers such as nylon, carbon, aramid and glass fibers gained interest owing to superior strength and precise dimensional control. Natural fibers were then replaced by synthetics in many fields such as textiles, sports goods and appliances. In the past decades, however, environmental issues drawn, once again, the attention to lignocellulosic fibers as possible substitute for intensive energy-consuming and long term polluting synthetics, specially the glass fiber(1). In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites(2-3). Among the advantages it is worth mentioning the renewability, recyclability, biodegradability and the fact that natural fibers are neutral with respect to CO2 emissions responsible for global warming. In addition to environmental benefits(l,10) the lignocellulosic fibers present economical advantages, such as worldwide abundance and comparatively low costs as well as some technical properties associated with flexibility and toughness( 4), which contribute to the performance of automobile components fabricated with natural fibers composites(l 1-13)."

Jan 1, 2013

By Thomas Gliick, Jianming Lu, David Dreisinger

"The Boleo project of Baja Mining (Vancouver) will process a mixed oxide-sulfide ore using an acid oxidation and reduction process in seawater to extract copper, zinc, cobalt and manganese. Copper will be extracted via SX-EW as copper cathode, zinc will be recovered as a zinc sulphate monohydrate crystal and cobalt will be produced as a cobalt cathode product after phosphinic acid extraction. Manganese may be recovered from the final solvent extraction raffinate by precipitation as manganese carbonate.The development of the cobalt recovery process (solvent extraction and electrowinning) will be discussed. The pilot plant solvent extraction circuit and subsequent bench and small pilot testing of cobalt electrowinning will be discussed. The Boleo project will produce approximately 1708 tonnes per armum of cobalt metal when fully commissioned.INTRODUCTIONThe Boleo property is held by the Mexican company, Minera y Metalllrgica del Boleo S.A. de C.V. (MMB). MMB is owned 70% by Baja Mining Corp. and 30% by a consortium of Korean companies consisting of KORES - Korea Resources Corporation, LS Nikko Copper, Hyundai Hysco, SK Networks and Iljin Copper. The project is fully financed and is now under construction with an expected startup in early 2013 .Average annual production, for the first six years for each of the metals is forecast as: 56,697 tonnes of copper cathode, 1,708 tonnes of cobalt cathode and 25,364 tonnes of zinc sulphate monohydrate. The project has an average life-of-mine cash cost (based on the three year trailing average metal prices, as of December 31, 2009, in accordance with SEC guidelines) of -$0.29/lb Cu, net of by-product credits for cobalt and zinc and with no credit for manganese production. There is the potential to produce up to 220,000 tonnes per armum of manganese carbonate (- 100,000 tpa contained Mn) via the relatively simple addition of a small number of unit operations to the proposed plant. The recovery of manganese metals from the manganese carbonate intermediate material is discussed in a separate paper in this proceeding."

Jan 1, 2012

By Akita Ito, Sumio Kato, Mikio Sugai, Shinichi Nakata

"Spark Plasma Sintering (SPS) is a newly developed method for the sintering of metal and ceramic powders, and completes their densification at low temperature and in short period. The SiC powder was synthesized from diatomite and graphite or carbon black by heating at 1 450°C for 1 hr in an argon atmosphere. The synthesized SiC powder was heated at 1500-1800°C, 50 MPa for 15-18 min by SPS. The relative density of sintered SiC body increased with the rise in the temperature. The oxidation of the surface of the SiC particle and impurities in SiC from diatomite greatly influenced the sintering promotion of SPS.IntroductionThe SiC has high hardness because of the covalent bonding, and is also excellent in thermal and chemical stability. However, it is difficult to obtain a dense SiC sintered body by the combustion heating-method. Therefore, the dense SiC bodies have been made by the use of additives and I or the hot pressing (HP) method.In this study, the SiC powder was synthesized by using diatomite of natural products and graphite, and carbon black of reagent as raw materials, and the relationship between the properties of SiC powders prepared at various synthetic conditions and the density of sintered body by SPS was examined."

Jan 1, 2000

By Ian Masters, A. R. Khoei, D. T. Gethin

This paper describes an experimental investigation into the effects of process parameters on product quality during an aluminum recycling process. In order to build a model relating recovery to the process parameter variables and then use the model for prediction, process optimisation, or process control, a historical data analysis is employed by observing patterns in the datalogged information at IMCO Recycling Ltd. In previous work, we emphasised the importance of expressing the results of an experiment quantitatively, by implementation of a Taguchi approach, to facilitate understanding, interpretation and implementation. This research presents the technical tools that are needed to achieve quality improvement in recycling of aluminum. In this study we apply the use of historical data matching through a Taguchi orthogonal analysis, in order to control and improve the quality characteristic. For this purpose, a numerical model is developed to characterise the inputs and outputs of the process. A response surface methodology (RSM) is employed to find a suitable approximation for the true functional relationship between response and the process parameter variables. The method of least squares is used to estimate the approximating polynomials. Subsequently, Taguchi's method is used to determine the relative significance of each of the parameters. Finally, process management software (written in Visual Basic) is described, and its interface with the process modelling and optimisation routines is discussed.

Jan 1, 2000

By P. G. Schirk, D. J. Roth

ALTEK has developed a processing system that can receive large pieces of dross & bath, of various metal contents, and reduce and separate these highly metallic concentrates into oxides and non-metallics. This system achieves these results without grinding the metallics into fines. Its unique feature results in the preservation of metallic unit in its largest possible size, which allows for maximum .metal recoveries. The Tumbler, an ALTEK-Didion International joint development, and the ALTEK High Velocity Impacting System (HVIS) are the key elements to this process. This paper will explore the advantage of this cold cleaning system over the direct melting of the raw dross in the reduction of landfill waste. The system also works well for removal of the aluminum from bath from primary smelters.

Jan 1, 2000

By F. M. Doyle, K. Sreenivasarao

Copper and cadmium metal has been recovered from dilute (3 X 10-4 mol/dm3 ) chloride solutions by ion flotation with dodecysulfate, followed by electrolysis. This approach should facilitate treatment of effluents too dilute for effective direct electrolysis. . The adsorption density of metal dodecylsulfate complexes on bubble surfaces was estimated from surface, tension data, and compared well with experimentally-observed metal removal kinetics, and ultimate recoveries. Copper and cadmium were recovered by electrolyzing the foamate, using steel wool cathodes and a graphite anode. The stability constants of the copper and cadmium dodecysulfate complexes are estimated, and used to analyze the thermodynamics of electrolysis. Dodecysulfate was unaffected by the electrolysis process, and hence could be recycled to ion flotation. A conceptual flowsheet for an overall effluent-treatment process is presented.

Jan 1, 1997

By Robert T. Oxnard

"EXECUTIVE SUMMARYThe history of Refractory Recycling indicates there was little recycling until the 1950s. Energy incentives were the primary reason for the beginnings of a recycling effort by the refractory brick manufacturers. Quality benefits quickly became evident and fewer rejects were the result. Today, economic factors including higher valued raw materials and increased competition are the driving forces of refractory recycling.There are some success stories in refractory recycling but we have a long way to go. Few incentives, quality concerns, relatively cheap energy, comparatively lax government regulations, inexpensive landfills and inexpensive substitutes make recycling a difficult choice for many companies. Marketing advantages such as ISO 14000, eliminating multiple audits and reduced liability exposure can tip the scales toward recycling viability. Increasingly, the ideological philosophy of a company, a desire to minimize environmental impact and develop favorable public and other interested party perceptions can drive recycling and waste minimization efforts.Recycled materials can be more trouble ""up front"" and harder to ""manage"" due to their suspect quality. However, due to their nearly inexhaustible supply and the fact that once developed, they constantly contribute to the bottom line, they are certain to be the materials of the future. Waste refractory materials will likely see the same bright future as the steel scrap yards and slag piles of yesterday. In hindsight, we will realize that now was the perfect time to prepare and plan for the bright future of refractory recycling."

Jan 1, 2000

By Jing Zhang, Chenguang Bai, Fusheng Pan

"The microstructure and hot deformation behaviour of an Er-modified Mg-Zn-Ai alloy were evaluated. The results showed that the addition of rare-earth Er changed the morphology of the quasi-continuous grain boundary networked eutectic compound to globular particles. Moreover, a self-strengthening effect was identified for the alloy, which determined its deformation behavior. After hot extrusion, the yield strength and elongation to failure of the Mg-Zn-AI-Re alloy at 200°C were increased by 105% and 120%, respectively, due to an emerged dynamic precipitation strengthening mechanism.IntroductionMagnesium alloys are attracting increasing attention for applications in automobile, electronic devices and hand tools for weight reduction and higher fuel efficiency, because of their lightweight and a high specific strength. However, application of Mg is still very limited. The largest applications are still those non load-bearing castings used at room temperature, such as box case, housing, and covering. One of the main reasons is the inadequate absolute strength both at room temperature and elevated temperatures (> 100°C) of the commercially used AZ, AM series alloys, due to the incoherent interface between the secondary phase y-Mg17AI12 and Mg matrix, as well as the low thermal-stability of the y phase [1]. Besides, the heat-resistant magnesium alloys which contain rare earth (Re) as the main alloying element are very expensive. The other reason is their poor deformability. The key solution is therefore to develop low-cost heat -resistant wrought alloys."

Jan 1, 2012

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"The structural and electronic properties of cubic d -NbN are investigated using density functional theory (DFT) and all-electron full potential linearized augmented plane wave method (FPLAPW). The equilibrium structural parameters are determined by fitting the total energy as a function of volume to the Murnaghan's equation of state. We calculated the total and partial densities of states (DOS) and compared them with those computed by different authors. Our DOS at Fermi level is found to be very close to the experimental value. The band structure is computed, discussed and used to find the characteristic energy separations. Valence electron density contours are recorded and discussed. We deduced the partial charge densities of different bands and binding energies of valence core levels and compared them with experimental and theoretical results obtained by different authors.IntroductionNiobium nitride has been intensively investigated over the last decades because of its interesting physical properties and technological applications (superconducting microdevices, microelectronic, catalytic probes, and hard coatings) [l]. While the group IV transition metal nitrides (TMN) mainly crystallize in the cubic NaCl structure (Bl type), those of group V and VI nitrides occur as different phases. Thus for niobium nitride, many phases have been reported in the literature: cubic fcc d -NbN, tetragonal ? -Nb4N3, hexagonal d -NbN, hexagonal e -NbN, and low nitrogen content hexagonal ß -Nb2N [l, 2].Structural and electronic properties of niobium nitride were investigated theoretically and experimentally by many authors. For example, in 1975 Schwarz [3] obtained the partial density of states for NbC and NbN from APW band structure calculations. In 1975 Kallne and Pessa [4] studied the electronic structure of Nb, NbC and NbN by using X-ray emission. In 2003 Amriou et al. [5] studied the electronic structure and bonding mechanism of NbC and NbN compounds using first principle total energy calculations using the full-potential linearized augmented plane wave method. Also in 2006 Sanjines et. al [l] studied the electronic structure of the hexagonal~Nb2N, hexagonal' d -NbN, and cubic d -NbN thin fihns by using X-ray photoemission spectroscopy. They [l] also calculated the densities of states for these phases and used them in the interpretation of the experimental valance band spectra. Most of these studies are old and there is a need for more recent studies. According to our knowledge, there are little comprehensive theoretical studies on this subject by using FP-LAPW method [5], which proved its ability to give accurate results. In this work we used the FP-LAPW method to study the structural and electronic properties of the cubic (fee) o-NbN (space group Fm-3m, prototype NaCl) crystal."

Jan 1, 2013

By Yotamu Stephen Rainford Hara

"The study focuses on the reduction mechanisms of copper, cobalt and iron during carbothermic reduction of copper-cobalt mineral sulphide concentrates in the presence of lime, in the temperature range of 1073K and 1273K. We have used three types of mineral concentrates which were derived from froth flotation from the Copperbelt region in Zambia. The reduction mechanisms were studied using thermogravimetric analysis in which selected reactions were stopped at different times for characterising the reaction mechanism using optical microscopy, XRD and SEM-EDX analyses. Using SEM-EDX analysis, we have analysed in details the stages of metallic phase formation during reduction process. Metallic cobalt and iron were embedded into copper, thereby permitting magnetic separation of the reduced metals even though copper is diamagnetic. Methods of preferential reduction of metal values were investigated by analysing the metallic phase formation.IntroductionIn conventional smelting or converting of copper sulphide minerals, metallic copper forms by giving off S02 gas on. Although in terms of overall energy balance the selective oxidation for metal production has major advantages, the process suffers from drawbacks in smelting complex concentrates containing copper, cobalt and iron sulphides minerals and these are: (i) cobalt and iron are oxidised, and consequently cobalt is lost into the slag phase. (ii) The volume of S02 gas produced is in low concentrations, which is insufficient for extracting sulphur or manufacturing sulphuric acid. The release of dilute S02 causes serious environmental pollution. The major cause for the loss of cobalt and iron into the slag, is due to that fact that the oxides of these metals are more stable than their sulphides. Since cobalt and copper are more valuable than iron, reducing conditions are required in a separate slag treatment reactor using electric arc melting for recovering the lost metal oxides from slag. This energy-intensive step makes metal making expensive.During chemical beneficiation of mineral sulphides (Cu2S, CoS, FeS) in the presence oflime (CaO), two types of equilibrium conditions may be set up either by forming CaS under reducing conditions, or by stabilizing CaS04 under oxidising conditions [l]. By comparison in the presence of carbon, CaS and metallic phases form, enabling the recovery of metals from sulphide minerals, which have been investigated by a number of authors [2-9]. During reduction of metal sulphide in the presence of lime and with carbon, it has been proven that the overall reaction le proceeds via two main steps: [5, 8, 9] (i) the anion exchange reaction between metal sulphides (MS) and CaO as shown in equation la, followed by (ii) the reduction of metal oxide (MO) via reaction lb."

Jan 1, 2013

By W. C. Hellyer

The papers in this section provide several examples of the application of Process Mineralogy to metallurgical problems. Any experienced metallurgist could cite numerous other examples when process mineralogy has, or could have, provided data of value in his understanding of metallurgical processes. The data developed by mineralogic techniques may supplement conventional chemical analyses, but cannot be replaced by assays. Mineralogic and chemical analyses each provide different types of information. In order for the process mineralogist to interpret his results in the most useful manner, it is desirable that he should have some knowledge of metallurgical processes. Conversely, the metallurgist should have some knowledge of mineralogic techniques to understand the scope and limitations. Mineralogic examinations are time-consuming and expensive. To ensure the effort is not wasted, and indeed does not generate misleading information, the utmost care must be taken at every stage of sampling and sample preparation. The mineralogist may examine microscopically or by x-ray diffraction a one-gram sample representing a flow of possibly thousands of tons per day through a concentrator. Conditions in a concentrator change continually in response to changes in feed rate, feed characteristics, grind, reagent additions, temperature, circulating loads, etc. Lengthy sampling periods are required to ensure the samples examined are representative of average conditions. The sampling program should be drawn up jointly by the metallurgist and mineralogist. Sampling points should be selected with a view to ease of sample cutting. The sampler should be instructed in the method of cutting the samples, the weight or volume of sample to be taken at each cut, the sampling frequency, and sampling period. The sampling period required depends on the scope of the investigation. For example, if a complete survey is to be made of all final and intermediate products of a flotation concentrator, samples should be cut at not more than two-hour intervals, twenty-four hours per day, for not less than one week. For a more limited investigation of one circuit or one section of a concentrator, 'the sampling frequency could be increased to every hour and the sampling period reduced to one or two days.

Jan 1, 1981

By Adam Powell, David Dussault

"Electric Field-Enhanced Smelting and Refining is a process for driving the reaction between carbon in hot metal and iron oxide in slag, for example, in a steelmaking reactor. This process involves inserting electrodes into the slag and metal phases, such that the overall reaction FeO + C -> Fe + CO is separated into two half-cell reactions: Fe2+ + 2e· -> Fe at the cathode in the slag, and C + O 2 • -> CO + 2e· at the anodic slag-metal interface. Without the electrodes, the reaction is very slow, but with electrodes, the additional surface area available to the ferrous ions for reduction accelerates the reaction even without any applied bias. When a bias is applied to the electrodes, the electric field across the slag further accelerates the overall reaction.With or without applied bias, the process is first-order in the ferrous ion concentration, and limited by ferrous ion transport to the cathode. To complicate matters, as the liquid iron is reduced at the cathode, the Mullins-Sekerka instability leads to formation of dendrite-like liquid iron fingers which grow into the slag. Because of this, the design of the cathode can have a significant effect on the overall process kinetics, and understanding of the dynamics of these fingers and of their effect on mass transfer is necessary for the intelligent design of the overall process and the cathode in particular.Toward this end, a detailed mesoscopic two-phase slag-metal model is presented here which describes multi component diffusion in the slag and fluid flow in both phases in the vicinity of the cathode. Diffusion in the slag is driven by chemical and electrical potentials. The phase boundary is modeled as a diffuse interface using a phase field approach. Because this electrochemical reaction occurs at high-temperature, the kinetics of charge transfer and adsorption through the double layer are fast relative to transport, permitting the use of simple linear reaction kinetics. This also eliminates the need to discretize the double layer, with the result that charge neutrality may be assumed everywhere in the domain. Introducing electric field dependence of the gradient potential and well height coefficients in the free energy function allows the model to capture electrocapillarity at the interface."

Jan 1, 2001

By C. I. A. John

The slag dump at ZCCM's Nkana Division contains some 16 million tomes of slag, deposited since the mid-1930's. The average cobalt grade of the slag is 0.65% with some areas as high as 3%. Current arisings of slag from Nkana Smelter also contain significant tonnages of cobalt. Intensive investigations were conducted in the past into methods of recovering cobalt from these slags, although none of the processes was developed to a commercial scale. The company is now working to develop a long-term strategy for ensuring the continuing production of cobalt at optimum levels, and the resource represented by the Nkana slags will be a major component in such a strategy. The present paper reviews the various processes which have been considered for recovering cobalt, both from the dump slag and from the current slags.

Jan 1, 1993

By T. V. Jayaraman, Kranti Kumar, Paul Praveen J., Dibakar Das, A. R. James

"Lead free piezoelectric ceramics with high piezoelectric coefficients are in great demand for sensor and actuator applications. Synthesis and characterization study of one such lead free system, barium zirconate titanate - barium calcium titanate [xBZT-(1-x)BCT] (x = 0.5), via solgel method have been carried out. X-ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed the formation of single phase BZT-BCT nanoparticles (<50 nm). The as-synthesized powders were calcined at 1000°C and the powders were pressed into cylindrical pellets. Solid-state sintering of the green pellets at 1550°C for 2 hrs resulted in single phase perovskite structure. Hysteresis loops were obtained which indicates the ferroelectric nature ofBZT-BCT. The bulk ceramic samples with the highest sintered density (~93%) were subjected to electrical poling and the piezoelectric properties ( d33, kp, & i:,) were measured. The structure and piezoelectric properties were investigated and correlated for the given composition of the BZT-BCT system.IntroductionPiezoelectric ceramics are widely used in various sensors and actuators and most of the piezoelectric ceramics, which are presently used, are lead based, which contains at least 60% lead (Pb) by weight. The critical disadvantage of these lead based piezoelectric ceramics is their hazardous effect related to the toxicity of lead, which poses a serious environmental concern starting from their processing to the disposal stage[l]. It is well known that a material to be a good piezoelectric it requires a morphotropic phase boundary (MPB) i.e. the composition induced phase transition between any two ferroelectric phases."

Jan 1, 2013

By Wenshan Zhang

The industrial production experiments on Zn, Mn simultaneous leaching, impurity removal and ZnMnO2 simultaneous electrolysis were carried out. The process flow, technical requirement and research results about the experiments were discussed and the good technical quail-fixation and high quality of products were obtained. Reactions for each major technological process have been expatiated based on the thermodynamic analysis.

Jan 1, 2006

By Guo Xueyi

The nonferrous metal industry is facing the resource depletion, energy crisis and environmental deterioration. The resource recycling is a correct way to promote the nonferrous metal industry development towards sustainable. To realize the resource recycling, the technical support is most important. In this paper, the techniques barrier for nonferrous metal resource recycling are summarized, the fundamental on resource recycling of nonferrous metals are proposed.

Jan 1, 2006

By Richard Krentz

Two separate on-line analyzers are operated at the Corefco metals refinery. The first application is an on-line refractometer which measures the ammonium sulphate concentration in the primary feed slurry tank. The second application is a multi-stream X-Ray fluorescence analyzer which measures the metals and sulphur concentrations in eight key refinery streams. Specific applications of the on-line analyzers with advanced control systems for improved process control will be discussed.

Jan 1, 2003