Search Documents

By John L. Watson

Many metals-based industrial processes experience limitations in their operations due to an inability to effectively separate solids and liquids where partidesizes are less than 25 microns. Steel plant sludges ,generated, from the cleaning of furnace off-gases represent a typical example of processing difficulties attributable to material characteristics, and recycling or even efficient disposal of these materials is often a major problem. The use of a magnetic field to augment the traditional mechanisms of vacuum dewatering has, been demonstrated in previous work to have significant value in separating solids and 'liquids, where the solids exhibit some magnetic character. Magnetic vacuum dewatering has been used with magnetite ores and with blast furnace sludges and magnetic fields have been incorporated successfully in drum and disk vacuum filters. The research described in this paper investigates the use of magnetic seed material and flocculants to extend the application of magnetic, vacuum filtration to non-magnetic pulps. It is shown that the addition of a flocculant can enhance the capacity of drum and disk magnetic fIlters when treating materials, such as steelmaking sludges, which are only partially magnetic. In addition, the use of seed magnetite with a flocculant is shown to improve the dewatering of fine hematite pulps in a drum magnetic filter. However the use of a flocculant and seed magnetite had only limited success in improving filtration in a disk magnetic filter with a fine quartz pulp. A disadvantage of magnetic vacuum filtration with seeding appears to bean increase in cake moisture due to water entrapment in the floes resulting from agglomeration and magnetic attraction.

Jan 1, 1999

By Kikuo Okuyama, I. Wuled Lenggoro, Manabu Shimada

"Aerosol processing of materials such as (i) gas-to-particle conversion process (e.g., Chemical Vapor Deposition (CVD) method) and (ii) liquid (or droplet)-to-particle conversion process (e.g., spray pyrolysis) has become of major interest to produce novel submicron- or nanometer-sized particulate material used in electronic and chemical industries. After reviewing recent theoretical and experimental researches on the evaluation of properties and morphology of fine particles by the CVD and spray pyrolysis methods, the importance of the process engineering approach· for aerosol processing of materials and the use of advanced aerosol measurement technology have been pointed out.IntroductionMaterial synthesis via aerosol processing offers a route to producing nanometer-sized and submicrometer-sized particles of high purity with specifically tailored chemical and physical properties. Especially, single nanometer-sized particles (nanoparticle materials) are considered to play an important role in the synthesis of nanostructured materials as well as in nanotechnology in 21st century due to their quantum effect and so on.However, the transformation of gaseous or liquid precursors to the final functional particulate matters consists of various complex chemical and physical processes. In order to control the size distribution and morphology of produced particles, it is important to analyze and model various phenomena, such as gas-phase or liquid-phase chemical reaction, nucleation, condensation, agglomeration and sintering that occur simultaneously in aerosol material processing. By introducing the Aerosol Science and Materials Science, the authors have been trying to model the changes in particle properties and morphology by gas-to-particle conversion and droplet-to-particle conversion processes. The authors have also been trying to obtain the experimental data on the particles properties as accurate as possible."

Jan 1, 2000

By M. Patel, A. W. Piper, R. A. Forsdick

"Lead bullion is refined in kettles to remove the contained impurities such as copper, antimony, silver and bismuth. These impurities are removed sequentially by the addition of one, or more, reagents to the bath. Impurity elements react selectively with the reagents to form a dross layer on the surface that is subsequently removed for further processing. Mixing the lead bath using specific impeller designs, which form a vortex to ensure that good contact takes place, carries out the reactions. It is important that the mixing is controlled to achieve the optimum bath conditions and hence good dross grades.This paper presents initial modelling work on the kettle refining process using both physical modelling (Water Models) and mathematical modelling (Computational Fluid Dynamics - CFD). Comparisons between measured plant data and simulation results are given.IntroductionThe refining of lead bullion takes place in hemispherical kettles of varying sizes. It is normal practice to remove the impurity elements sequentially, by the addition of reagents, which selectively react with the impurity element. The impurity element forms a dross layer on the surface, which can be removed for subsequent processing at the end of the reaction period.All the refining stages in the production of lead and lead alloys involve mixing the lead bath, although different conditions are required for each stage. At Britannia Refined Metals mixing is achieved using either 3 or 4 angled or flat blade impellers, which generate a vortex in the central region of the kettle. However, throughout the industry a wide range of mixer types are used which are all trying to achieve the same result."

Jan 1, 1999

By Cheng Yan, Yugang Li, Qian Wang, Lizhi Zhang

In continuous casting process, mold powder has lots of metallurgical effects, such as covering the molten steel to prevent liquid steel from oxidation by air, preserving heat for top layer liquid steel, lubricating initial shell and so on. However, mold powder also can deteriorate the quality of final products obviously after the entrapment of mold powder in steel. In the present work, based on the similarity theory the effect of technological parameters on mold powder entrainment was investigated by water model. Experiment was carried out in the water mold using oil and water to simulate slag and steel, respectively. The results showed that increasing casting speed increased the water-oil interfacial fluctuation and entrainment frequency; viscosity of oil also had a great impact on the interface fluctuation and entrainment; water-oil interfacial tension effect the entrainment while not changing the interfacial fluctuation; submergence depth had little impact on entrainment and interfacial fluctuation.

Jan 1, 2015

By Xiaojie Gao, Shufeng Yang, Jingshe Li, Chengsong Liu

In the blast furnace process, the dust entrained in the blast furnace gas enters into the down-comer, flows through the gravity dust separator (to eliminate coarse particles) and then is collected in a bag-house. The powder collected by the baghouse is called bag dust, while both fractions are called blast furnace dust whose main components are C and Fe. The dust also contains small amounts of nonferrous metals such as Zn and Pb, which have some value. Also, due to the small particle size and low density the dust is easily suspended in air and so can endanger human health. Therefore it is necessary to develop a process to both treat the dust to recover the metal values and to dispose of the residue – preferably by recycling to the blast furnace itself via the sinter strand. These objectives will result in good economic, environmental and social benefits [1].

Jan 1, 2014

By Kunibert Hanusch

Copper in recycling material is accompanied by various groups of metals: 1) Metals which are much more negative than copper, such as Fe, Al, Si, P, Be They are mainly removed by fire refining during the recovery of copper and leave the process in form of slag. 2) Metals which are more positive than copper or difficult to separate by fire refining and which are partly reduced together with the copper. These metals are for example As,. Sb, Ni, Ag, Pb, Zn, Sn. They are enriched in intermediate products and recovered from these or remain for their major part in the fire-refined copper and can be separated by electrolytic refining and recovered from the electrolyte or anode slime. This report describes the process of Hüttenwerke Kayser AG in Germany and illustrates how considerable returns of material are partly required to separate or recover associated metals. They are finally removed in saleable products.

Jan 1, 1995

By I. Van de Voorde

In this paper, results are presented concerning the search to implement Supported Liquid Membranes (SLM) Technology for the recovery of copper, nickel and zinc from electroplating and other effluents to prevent metal waste. A study of the influence of the individual parameters and of their combined effect on mass transfer in small-scale laboratory equipment has been performed, enabling to set forward the appropiate operating conditions for a pilot plant installation. The SLM pilot plant has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that the SLM technolgy is applicable for solutions containing 800 mg/L of metal ions, but also to the treatment of solutions with low metal content of origin other than plating shops. It was demonstrated by system analysis that the recycled salts are usable to produce metal electrolytes (for example Watt's nickel bath).

Jan 1, 2003

By Kamal Adham

Hydrochloric acid is used as lixiviant in such hydrometallurgy processes as synthetic rutile production and nickel extraction. The intermediary metal chloride is normally roasted to release gaseous HCl and a solid metal oxide. A large amount of fuel is required for this thermal regeneration, mainly to vaporize the water content of the feed solution. To conserve fuel, some energy recovery from the off-gas is currently achieved, but the fuel costs can further be reduced by process optimization and energy recovery from the gaseous, aqueous and solid products of the regenerator. Here, first the existing limitations to fuel efficiency in the industrial scale HCl regeneration roasters are described. Then, for the case of a dilute feed solution, options for pre-evaporation and fuel minimization are modeled and compared. Finally, energy recovery technologies including heat pumps, acid heat exchangers and solid waste heat boilers are described, and their potentials as the heat source for pre-evaporation of the feed are evaluated.

Jan 1, 2003

By P. J. Moor

Britannia Refined Metals Ltd. was built in 1931 to refine the lead bullion produced at the Mt. Isa mine in Queensland, Australia. Several periods of expansion and development have taken place over the intervening years, leading to major increases in the refining capacity for both lead and silver. A plant for treating recycled lead-acid batteries was added in 1976. This was redeveloped in the early 1990's to utilise Isasmelt technology for the smelting operations. Most recently the No. 2 refinery kettle floor was extended to enable it to process lead bullion produced from two Imperial Smelting Furnaces (ISF), at Britannia Zinc Ltd. in Avonmouth, England and at MIM Hüttenwerke in Duisburg, Germany. This expansion included the provision of a plant for the hygienic handling of drosses and skims. This paper briefly describes the present primary refining operations and gives an update on the most recent developments in the process metallurgy and operating practices that have taken place.

Jan 1, 2000

By Shadia J. Ikhmayies

"Cadmium sulfide thin films were prepared on glass substrates by the spray pyrolysis technique at a substrate temperature of 490°C. Some of the films were etched by HC1 in distilled water, others were heat treated in nitrogen atmosphere, and another set of films was first etched by HC1 and then annealed. Room temperature impedance spectroscopy measurements on the films were performed using coplanar geometry in the dark and in room light in the frequency range 20 Hz to 1 MHz. The experimental data were represented by complex plane diagrams and showed one well-defined semicircle in the high frequency region. Hence the equivalent circuit that models the CdS: In thin films was found to be a single RC circuit, which indicates the bulk conduction through the grains. The influence of treatments on the electrical properties was investigated.IntroductionCadmium sulfide (CdS) is a brilliant II—VI semiconductor material with a direct band gap of 2.42 eV at room temperature. It has many outstanding physical and chemical properties, which have promising applications in multiple technical fields including photochemical catalysis, gas sensor, detectors for laser and infrared, solar cells, nonlinear optical materials, various luminescence devices, optoelectronic devices and so on [1]. There are different methods to prepare undoped and doped CdS films, such as rf sputtering [2] chemical bath deposition (CBD) [3], pulsed laser deposition (PLD) [4], and spray pyrolysis (SP) [5-11]. Of these methods, spray pyrolysis represents the less expensive option, and can produce large area high-quality low cost thin films [12]."

Jan 1, 2012

By Daniel Helm

The first industrial application of direct solvent extraction of nickel from hypersaline sulfate feed solutions has highlighted the need to investigate the influence of chloride on the extraction behaviour nickel in the presence of calcium using Versatic 10 and the solubility characteristics of gypsum. Temperature-solubility curves for gypsum in various aqueous electrolytes were prepared. The solubility of gypsum is increased significantly by the presence of sulfate ions, while chloride ions decrease it for a given temperature. The anion effects of chloride and sulfate on the extraction of calcium and nickel by Versatic 10 corresponded well with the complexing ability of the anions. It was shown that the presence of chloride shifts the extraction isotherms for both metals significantly to the left, while decreasing the selectivity of Versatic 10 for nickel over calcium. The loading of nickel onto Versatic 10 in this system was shown to be at a maximum within 3 seconds, while calcium extraction took between 4 ? 5 seconds to load to a maximum. Chloride ions had no influence on loading kinetics of nickel, but depressed the rate of calcium loading. It was shown that in the presence of an excess of nickel, calcium loading is effectively eliminated, and that calcium is scrubbed from Versatic 10 within 2.5 seconds of contact with nickel electrolyte.

Jan 1, 2003

By Bradford C. Wesstrom, Omar Araujo

"Impurities from an electrolytic refinery are typically extracted from the electrolyte utilizing conventional electrowinning cells. These cells are arranged in series with cascading solution flow and are commonly referred to as liberator cells. The Freeport McMoRan Copper & Gold El Paso Refinery has optimized the removal of arsenic in cascading liberator cells by utilizing two separate feed solutions. The primary feed solution is recycled liberator electrolyte and the secondary feed solution is ""neat"" tank house electrolyte. The secondary feed solution is added based on the voltage response across the individual cells utilizing independent variable frequency drive (VFD) pumps. When the voltage across a cell changes, a signal is sent to the VFD pump to maintain a cell voltage of 1.98 volts. By maintaining this voltage the copper content in each cell exits at 2-4 grams per liter. This safely optimizes the arsenic removal as copper arsenides on the liberator cathodes.IntroductionDuring the electrolytic refining of copper, impurities from the copper anode report both to the bottom of the electrolytic refining cell as slimes and to the electrolyte. The impurities which enter the electrolyte are arsenic, antimony, bismuth and nickel. The impurities that report to the electrolyte during the electrolysis process gradually increase. As these impurities increase, they are incorporated into the refined copper cathode. There are many processes that have been used to remove these impurities from refinery electrolytes. Some of them are listed as follows: solvent extraction, ion exchange, hydrogen sulfide reduction, bioreactor, adsorption onto a low - solubility metal-oxide hydrate, adsorption onto activated carbon and EMEW cells. The conventional process used by the copper refining industry for controlling the level of impurities in electrolyte involves multistage electrolytic cascading liberator cells. In these cascading liberator cells copper, arsenic, antimony and bismuth are removed as various mixed deposits from the electrolyte. Removal of these impurities is achieved through an increase in voltage resulting from the depletion of copper in the electrolyte through electrowinning. With this higher voltage, the Group Vb elements, arsenic, antimony and bismuth are deposited on the copper cathode and report as slimes to the bottom of the cells. Nickel is removed in a subsequent process."

Jan 1, 2012

By R. D. Osmanson

A series of batch roasting tests was performed on minus 1/2 inch gold bearing refractory samples from the Gold Acres deposit, and 67 select particles were polished and the sulfide alterations were examined microscopically. The suite of specimens represents two hour batch roast treatments at 600°C, 700°C, 725°C, 750°c, 800°C, and 900°C. Auriferous pyrites were found to alter sequencially to pyrrhotite, magnetite and finally to hematite. It was found that the decrease in cyanidation extraction with high temperature roasting is likely due to the increas ing stability of magnetite and more crystalline hematite, and the decrease in porosity with these phases which occlude the gold. Gold has been noted to occur very early in the mineralizing sequence, with gold being found in quartz and in clay/carbonate rock matrix. No gold was found in the two pyrite phases, but numerous gold grains were found in pyrrhotite after pyrite and in subsequent iron oxides. Gold mineralization had apparently ended by the time base metals were introduced into the deposit.

Jan 1, 1987

By Xiping Chen, Wangxing Li, Jiemi Zhou

"Desulfurization methods suitable for anode-grade petroleum coke (coke for short) used in primary aluminum industry are coke desulfurization during calcination, desulfurization in soakage and desulfurization in mediums. Coke desulfurization during calcination is discussed in this paper. Influences of calcination temperature, holding time and coke granularity on coke desulfurization were discussed. Experimental results show that calcination temperature has a remarkable influence on coke desulfurization. When the temperature is high enough desulfurization ratio of coke can reach 85% only by calcination. Holding time has a definite influence on coke desulfurization, but desulfurization ratio is low at the temperature of 900~1300°C. The influence of holding time is obvious when calcination temperature surpasses 1400°C. The influence of coke granularity is smaller compared with calcination temperature and holding time.IntroductionPetroleum coke is main raw material for carbon anode in primary aluminum industry, and its weight percentage in carbon anode is about seven percent. Green coke can not be directly used for anode production because of its immanent moisture and volatiles. Green coke must be calcined in order to meet the request of anode production. Calcination is a heat-treatment process during which green coke is heated to a given temperature to remove volatiles, moisture and some sulfur. Real density, strength, electrical conductivity and anti-oxidation ability of petroleum coke can be improved by calcination and calcined coke can be received [1, 3, 4]. Sulfur in calcined coke finally goes into carbon anode. During baking or aluminum smelting, the sulfur in anode ultimately changes into SO2 and emits from anode into the atmosphere. Excess SO2 easily leads to acid rain which brings heavy pollution to the environment [1, 2]. With the development of Chinese aluminum industry, consumption of anode-grade petroleum coke increases year by year, the total consumption in 2007 surpassed 4.5 million tones and the yearly emission of SO2 from aluminum smelters has exceeded 270 kilotones. From 2005 Chinese government began to limit the emission of SO2 from primary aluminum industry, so desulfurization of anode-grade petroleum coke becomes more and more urgent. Some relationship need to be found and used to guide desulfurization of petroleum coke."

Jan 1, 2008

By Liang Yu, Yuhua Li, Yuanchi Dong

"High alumina slag, with alumina normally more than 15 pct, is encountered with blast furnaces in China because of high alumina/silica ratio in iron ore as well as sinter and high ash content in coke for cost reason. High alumina slag with high viscosity and high liquidus temperature would lead to higher slag volume and thereby, furnace productivity. In the present work, liquidus temperature of high alumina slag, based on Meishan factory, Baosteel China, were investigated. A liquidus temperature model was introduced in the present work based on basic physical chemistry theory and focused on the chemical composition area used in Meishan factory(pct): Al2O3 from 14 to 17.5 and MgO from 8 to 12, so that the blast furnace slag could be designed for optimum blast furnace performance.IntroductionBlast furnace slag composition[1] has very important bearing on its physicochemical characteristics which affects smoothness of operation, slag handling, coke consumption, the degree of desulphurization, hot metal productivity and its quality etc. The slag properties which affect most are liquidus temperature, viscosity, sulphide capacity and alkali capacity. Variation of these slag characteristics with composition and temperature has been a field of active researches as these its great influence on the blast furnace operation. In the early years, most of these studies were carried out over low alumina blast furnace slags with alumina normally less than 15 pct. High alumina slag was first introduced in India because of its high alumina/silica ratio iron ore as well as sinter and high ash content in coke[2]. And then this problem becomes common as higher alumina/silica ratio iron ore imported and used [2-5]. The most important problem caused by high alumina content is liquidus temperature and then viscosity of the slag.Generally speaking those reported works [2-5] investigated a pretty wide range of chemical compositions and then obtained complex model, respectively. In fact, every factory has its own interest because of different resources. For example, the Al2O3 content from 20% to 30% pct was studied in Tata Steel India [2], but it is too high for Baosteel Meishan. A very lower percentage of alumina content, 14-18 % pct, was mainly used."

Jan 1, 2008

By D. G. C. Robertson

Counter-current staged reactors offer several advantages over batch reactors for mass transfer between two phases. Several metallurgical reactor designs have utilized the counter-current principle, e.g. the WORCA and QSL processes. But before the principle can be widely adopted, it will be necessary to overcome several significant problems. These include the need to minimize longitudinal mixing in a single reactor or to use several separate staged reactors and to carry out different reactions in sequence, e.g. phosphorus oxidation and sulfur reduction. Theoretical and experimental approaches to these problems will be discussed in the paper.

Jan 1, 1988

By Kenji Monden

"The creep properties of tin-based lead-free solders Sn3.0AgO.5Cu and SnO.7CuO.1Ni and lead solders 10Sn90Pb and 50Sn50Pb were investigated at temperatures between 298 K and 398 K. The creep-rupture time decreases with increasing initial stress and temperature. The analysis of the solder creep curves uses the Omega method. The creep rate E is expressed by following formula: 1n ? = 1n ?0 + O?, where ?0 and O are experimentally determined. The parameter Eo increases with increasing initial stress and temperature. The activation energy for ?0 is 108 kJ/mol for Sn3.0Ag0.5Cu and 85 kJ/mol for SnO.7CuO.INi. These energies suggest that the lattice diffusion of tin is dominant. The energy of 1OSn90Pb is 37 kJ/mol and that of 50Sn50Pb is 67 kJ/mol. The creep-rupture time is calculated using the parameters, ?0 and O. The calculated creep-rupture time is in good agreement with the measured creep-rupture time.IntroductionLead-free solders are replacing traditional tin-lead solders as part of a major trend toward protecting the earth's environment. However, tin-lead solders are currently needed for a high temperature range. Since creep is the main deformation mechanism in solder joints, understanding a constitutive model for creep and examining creep data for solders are important for reliability analysis of solder joints. A steady-state creep equation is generally used for solders [1,2], and it supposes that the secondary-, or minimum-, creep rate occupies the entire creep life. However, secondary creep accounts for only about 15 % to 40 % of the entire creep life for solders. Thus, the equation may not represent the entire creep life."

Jan 1, 2012

By Romeo U. Pagador

After privatization in 1999, PASAR Corporation initiated a plant modernization program to optimize the performance of the smelter by increasing plant availability. This initiative required operational adjustments to the converting and anode furnace procedures, to support the higher throughput in the flash furnace, while continuing to meet government environmental regulations. The major shift in production direction was to eliminate the 30-35 day maintenance shutdown every two years, and replace it with a 15-day shutdown. This paper discusses the changes implemented in the converter and anode operation that have resulted in an increase of 10% in flash furnace throughput, an 18% increase in blister output, to 170 tonnes per cycle, and a converter campaign tonnage increase of 10%. Since privatization, PASAR has instituted a series of ?management of change? programs that have facilitated an industrial cultural change needed to achieve the company?s vision, mission and strategic goals.

Jan 1, 2005

By Xiangru Chen, Qijie Zhai, Wei Zhang, Haicheng Li, Chao Yang

In this paper, ductile iron material with different content of niobium was prepared by a scientific melting method. Image Analysis Software was used to studied the effect of niobium microalloying on both pearlite content and pearlite lamellar spacing in ductile iron quantitatively. The results showed that the addition of a small amount of niobium could increase the pearlite content and decrease pearlite lamellar spacing of ductile iron effectively.

Jan 1, 2015

By Norman L. Kotraba

Zia Metallurgical Processes, Inc. has developed and patented a steelmaking process capable of converting iron bearing metallurgical wastes into high quality steel products. The process utilizes a proprietary design rotary hearth furnace to convert iron bearing wastes, pelletized with coal, or other forms of carbon, into direct reduced iron (DRI). This DRI is fed, hot, from the rotary hearth furnace into a Zia All Purpose Vessel (ZAV) where it is smelted and refined into high quality steel. A specially designed turret with three independent arms, each supporting a separate ZAV, comprises the heart of the meltshop. No overhead cranes are required to transport molten metal from the smelting/refining operation to the ladle metallurgy station to the caster to an inspection station and back to the smelting/refining point. The molten steel is contained in the ZAV throughout the operations eliminating the possibility of steel con¬tamination by non-metallic inclusions occasioned by the exposure to ambient air during metal transfer into ladles. The result is the creation of very clean steel that can be alloyed to produce virtually any desired grade from stainless steel to common structural steel.

Jan 1, 1994