Search Documents

By W. Marnette

Norddeutsche Affinerie is the largest West European copper producer with an annual output of more than 350,000 tonnes of refined copper, about half of which is produced from copper concentrates. However, in addition to concentrates, Norddeutsche Affinerie processes secondary raw materials and recycling materials which contain a combination of copper and lead. These materials were previously treated in blast furnaces, a technology which has meanwhile been superseded at NA by the electric furnace process, primarily owing to the necessity of complying with the increasingly stringent requirements for environmental protection.

Jan 1, 1994

By Esa J. Peuraniemi

Copper smelting to form blister in one single step has been possible for a long time even from low grade concentrates. In spite of obvious benefits, it has been economically viable only with few special raw materials having high enough Cu/Fe and Cu/S ratio. Outokumpu Blister Flash Smelting is currently applied at three operations, and three others will be commissioned in the near future. With typical chalcopyrite concentrates two main obstacles have prevented wider adaptation of direct blister processing: slag formation and heat generation. Oxygen potential in the reaction shaft must be high in order to produce blister with targeted sulfur content below 1%. When large amount of iron is oxidized, as well as sulfur, copper is inevitably also oxidized into slag. High copper amount in substantial tonnages of slag lead on to costly down stream recovery operations to obtain discardable slag. Almost complete oxidation of sulfur and iron releases a high amount of heat which traditionally has been solved by lowering oxygen enrichment of the blast leading on to oversized off-gas line and acid plant. One challenge in direct blister smelting relates to the attack of aggressive high-copper containing slag against furnace refractory lining. In continuously operated Outokumpu Direct Blister Flash Smelting this is taken care of by preventing vigorous melt movement in the settler. Stable bath conditions and stationary slag against refractory lining enable the formation of a protective autogenous layer between aggressive slag and vulnerable refractory. These direct blister smelting challenges are addressed from equipment and process development point of view. New solutions to overcome the obstacles are presented and discussed.

Jan 1, 2006

By Min Chen, Zhen Tian, Hongxu Cui

"The effects of adjusting technology on the phosphorous enrichment in converter slag were investigated. The results showed that the grain size of 2CaO·SiO2 with high phosphorus containing content increased slightly with the decreasing of cooling rate, and the proper cooling rate was confirmed to be about l.0°C.min-1. Moreover, the morphology of the phosphorus-rich phase of 2CaO·SiO2-3CaO·P2O 5 was changed from granular for the higher basicity of converter slag to the coexistence of granular shape and rod-like for the lower basicity of adjusted slag. With the addition of adjusting agent such as SiO2 to lower the basicity of converter slag, the phosphorus in converter slag could be transferred into 2CaO·Si02 phase effectively, and P2O 5 content in high phosphorus containing phase reached to above 30%.IntroductionThe yield of converter slag is very large in China, but most of the slag is stacked usually after the separation of iron, which not only takes up a lot of land, but also affects the ecological environment seriously. Therefore, improving the comprehensive utilization and value-added products of converter slag is of great significance to recycle the steelmaking slag[l-3]. On the other hand, the refining of hot metal with high phosphorous content is an unavoidable problem with the decreasing of high grade iron ore, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. However, the current recycle of converter slag is more focused on the emission reduction and reuse of steelmaking slag inside the iron and steelmaking process without considering the recycle of phosphorous resources[4-6]. At the same time, the development and utilization of phosphate ore as a strategic resource is drawing more and more attention, but the phosphate ore in China is mostly low grade and significant amounts of tailings are produced which is harmful to the environment. Therefore, it is important to separate phosphorous resources in steelmaking slag which can be used as phosphate ore for fertilizer material[7-9].Literature studies showed that most of the phosphorus in steelmaking slag existing as 2CaO·SiO2-3CaO·P2O 5 solid solution phase in 2CaO·SiO2 particle. The P2O 5 content in the phosphorus containing phase is very low due to the fact that the basicity of converter slag is usually high and the precipitated amounts of 2CaO·SiO2 particles during cooling are very large, resulting in the fact that the P2O 5 contents in 2CaO·SiO2-3CaO·P2O 5 solid solution phase are much lower which is impossible to be used as phosphorous resources instead of phosphate ore. Thus, the enrichment of phosphorus in steelmaking slag is need[ 10-14]."

Jan 1, 2011

By Shadia J. Ikhmayies

"Cadmium telluride (CdTe) is a very interesting material that has many applications. Thin films of p-type CdTe can be used as the absorber layer in the heterojunction CdS/CdTe thin film solar cells in which n-type cadmium sulfide (CdS) works as the window layer. A review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques was performed. The presence of defects and impurities such as oxygen and chlorine influence the PL spectrum. Copper and other dopants change the PL spectra and enhance the defects band. Chemical-heat treatment especially with CdCh is known to improve the quality of CdTe thin films because it decreases the Cd vacancies and quenches deep traps, so it enhances the PL signal. A discussion of chemical-heat treatment especially with CdCh, the effect of the ambient atmosphere, and that of the measuring temperature is performed.IntroductionCadmium telluride (CdTe) is a II-VI compound semiconductor that has a cubic zincblende (sphalerite) structure with a lattice constant of 0 A4~11]. Other than all of II -VI semiconductors, CdTe can be made both n- and p-type. But due to self compensation it is not easy to get p-type CdTe films [2]. Polycrystalline CdTe thin films are interesting because they have a lot of applications. Most of the problems associated with the use of these films are attributed to inhomogeneity, self-compensation, and the difficulty of forming a stable and lowresistivity ohmic contact [3]. CdTe technology has been established for a large number of applications, including solar cells, optical and nuclear detectors, and thermal- and radiationimaging devices [3]. At present, the highest demonstrated conversion efficiency for a CdTe based heterojunction (ID), with CdS as a window layer, is 16.5% [4, 5]. CdTe thin films can be prepared by different experimental techniques, such as thermal evaporation [l], electrochemical deposition (ED) [3], close-spaced sublimation (CSS) [3, 4, 6], physical vapor deposition (PVD) [3], chemical molecular beam deposition (CMBD) [7], and close space vapor transport (CSVT) [8].The objective of this paper is to make a review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques and discuss the factors that influence the PL spectra. The composition of the film is very interesting in determining its PL spectrum. Different kinds of defects, impurities and dopants have their finger prints in the PL spectrum. Deposition techniques and deposition parameters such as the deposition temperature and ambient atmosphere also have their influence. Heat and chemical treatments which are known to improve crystallization and reduce the defects change the PL spectrum."

Jan 1, 2013

By James C. Foley, David K. Rehbein

"In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent ·advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ evaluations of the acoustic attenuation and velocity as sintering proceeds. Pure aluminum (99.999%) and aluminum alloy powders were prepared with high-pressure gas atomization (HPGA). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and attenuation during sintering. The changes in acoustic properties were correlated with sample microstructures and mechanical properties. Evolution of the acoustic echo train during sintering is shown to provide information on the state of sintering as well as having the potential for detection of interior flaws.IntroductionThe versatility of powder metalallurgy (PIM) technology in the manufacture of complex shapes has enabled an increasing amount of wrought and casting production capacity to be converted to PIM technology. However, ultrasonic inspection of green components produced using PIM techniques remains a challenge and is not generally practiced [1]. Inspection of PIM components in the green state is highly desirable, because the green part can be reclaimed with only accepted components being subjected to further costly processing. Another potential benefit is characterization and greater understanding of the sintering process itself. An increased scientific understanding of the sintering process enables intelligent process control, greater reliability of the production process and a lower rate of rejection of the finished product. In order to realize these potential benefits, it is necessary therefore that accept/reject criterion be based on real time nondestructive evaluation of the green-state components and the sintering process.Most current nondestructive inspection techniques suffer from their inability to perform inspections below the near-surface region with the exception of X-ray and to some extent pulsed eddy current [2]. X-ray inspection requires extensive shielding of production personnel and expensive film and film processing. While development of pulsed eddy current techniques have lessened the impact of the well-known skin effect, the depth of penetration of the induced eddy currents remains somewhat of an issue [2]."

Jan 1, 2000

By Bohumír Cech, Jirí Hanika, Václav Veselý

"PET bottles are separated and subsequently crushed into flakes. Except for PET, these flakes contain PE, PVC, paper, adhesives, beverages remainders and mineral impurities. PET itself usually is a glycol and terephthalic and isophthalic acid polymer.The suggested method consists in PET flakes crystallization at 255°C. In the meantime, volatile substances evaporate and PVC disintegrates. Formed crystalline PET is crushed into small particles and then is subject to the basic hydrolysis at an atmospheric pressure. In addition to lye solution, glycol is added in the hydrolysis. Water is eliminated by boiling, which gives rise to suspension of sodium salt of terephthalic acid and glycol. The suspension is skimmed and the filtered glycol is vacuum distilled. Pure glycol is then the distillation product.Crystals are dissolved in water and the solution is filtered, which eliminates PE and impurities. Electrodialysis removes pure terephthalic acid salt from the solution. Glycol solution is returned to the hydrolysis. Terephthalic acid is precipitated by a mineral acid. Subsequently, it is washed and dried. The filtrate is separated through electrodialysis to lye and acid. The lye gets back to the hydrolysis and the acid is used for precipitation. Terephthalic acid and glycol are products in a “polymer grade” quality. The waste is a part of washing waters, distillation residues after glycol regeneration and a filter cake after the terephthalate solution filtration."

Jan 1, 2008

By F. L. Marley

Small and medium-sized flotation plants with no assaying instrumentation still depend much upon the art of the operator to produce acceptable and consistent results. Improved performance can be accomplished by the use of the simple microscope set up as a control device. The visual recognition of products in the circuit does much to eliminate uncertain shift operating decisions and is an easy technique to acquire. Mineral staining methods further assist in the determination of components within the mill products. Simple mounting upon scotch tape and other adhesives is rapid and convenient. The microscope also has a practical role for the plant metallurgist or laboratory technician when evaluating middling products, and their routing within the circuit. Examples are reviewed where the microscope has been used for operational control in both sulfide and nonmetallic mineral flotation plants.

Jan 1, 1981

By Merete Tangstad, Ragnar Tronstad

Ferromanganese production in electrical furnaces is quite an old process. However, as the furnaces are getting bigger, the requirements of cost, yield, product quality, emissions and security are raised. With the increased expectations, the fundamental knowledge must follow. Within the last 25 years there has been a great effort both in the industry as well as the academic environment to push the limits of this process. This article will show some examples of improvements within fundamental data, reaction mechanisms and emissions over this time period.

Jan 1, 2014

By Tracey Brommer, Britt Elin Gihleengen, Elsa Olivetti, Randolph Kirchain

"Increased demand resulting from the economic and environmental advantages of recycling secondary materials has constrained secondary material supply. As a result of constrained supply, the conventional strategy to maximize recycled content in an individual aluminum alloy must be expanded to maximizing total recycled content in a given production period. This work compares the performance over a two week period of an actual remelter for two strategies; a sequential charge-by-charge optimization framework and an integrated approach that explicitly incorporates the production schedule. Optimizing across the entire two week production is found to increase recycled content and minimize primary and alloying material additions. It is expected that as the scrap material market continues to be constrained by high demand, longer term batch planning strategies that can optimize material allocation will deliver improved performance.IntroductionIntensifying economic and environmental pressure to incorporate secondary aluminum into products is pushing remelters to explore additional strategies and tools to increase recycled content. Aluminum remelters are exploring alternative sources of secondary materials because of constrained secondary material supply and relatively high primary and secondary material cost [1]. Computational models, such as blending models are a tool that could help industrial remelters mitigate supply and cost challenges and thereby increase recycled content. In particular, computational tools can help manage the incorporation of new raw materials of variable quality. Blending models find many industrial applications and have been explored for over sixty years originating with the classic nut-mix problem dating back to 1950’s [2]. Blending models optimize the raw material input to make a desired product subject to a series of constraints such as product specifications and material availability. Deterministic and linear blending model formulations are presently implemented in some industrial aluminum remelters [3]. The primary reluctance of aluminum remelters against computational model implementation is the incapability of their blending models to reflect the intricacy of industrial remelting conditions [4]. For example, to reduce calculation time, industrial aluminum blending models usually optimize a batch plan for a single alloy and are not formulated to optimize several products simultaneously. Since such a model does not include knowledge of subsequent charges in the optimized batch plan, the resulting batch plans tend to deplete the “cleanest” secondary materials leaving the more uncertain and compositionally challenging materials for later charges. As a result, a remelter may override the calculated batch plan or leave certain scrap materials out of the material input to conserve these materials for alternative products scheduled for later production. This work explores an alternative aluminum charge planning tool that can optimize across an extended production schedule and compares it to a heuristic sequential optimization strategy reflecting an industrial remelter."

Jan 1, 2012

By Dariusz Kopyci ski, Józef Dorula

The study proves that by introducing the iron powder and disintegrated steel scrap to low-sulphur cast iron still before the inoculation carried out with a conventional graphitising inoculant, the mechanical properties similar to those obtained during the inoculation treatment carried out on cast iron with the recommended high sulphur content are achieved. The said operation increases the number of crystallisation nuclei for dendrites of the primary austenite. In this case, the iron particles act as substrates for the nucleation of primary austenite, due to a similar crystallographic behaviour of the regular face centred cubic lattice The more numerous are the dendrites of primary austenite, the less free space is available in the interdendritic spaces for the formation of graphite eutectic grains, which makes the structure more refined (more eutectic grains) and the mechanical properties higher.

Jan 1, 2016

By Jie Li, Liangxing Jiang, Yexiang Liu, Junfeng Gui, Bo Hong, Xiaocong Zhong, Yanqing Lai, Xiaoying Yu

"Pb-based alloys with Pr and Ag were prepared in vacuum electromagnetic induction furnace. The tensile strength, corrosion rate and anodic potential in sulfate solution were measured, and the experimental data were analyzed according to the metallographic phases of alloys, the micromorphology and composition of their oxide films. The results show that, with the addition of Pr, the ultimate tensile strength and corrosion rate of pure lead were increased, and the anodic potential decreased. The extra addition of Ag can improve the properties of alloy further. Comparing with Pb-Ag0.8 alloy which is widely used in zinc electrowinning industry, the ultimate tensile strength of Pb-Ag0.6-Pr2.0 alloy was increased by 31.75%, the anodic potential under 50mA/cm2 was decreased by 30m V.IntroductionIn zinc electrowinning industry, the Pb-Ag (0.5-1.0 wt.%, 0.8wt.% normally) anode is widely used as an insoluble anode['l. It can meet the basic requirements, but still has several problems such as high oxygen evolution over-potential (about 860mV), unsatisfactory corrosion resistance, lead contamination of the cathode product and high consumption of Ag etc.In order to reduce the energy consumption, enhance the corrosion resistance, improve the product quality and reduce the consumption of Ag (or even dispense with it), much research has been done, mainly focusing on Pb-based alloy anodes and Ti-based coated anodes. Detailed investigations have already been carried out on binary alloys (Pb-Ca and Pb-Co), ternary alloys (Pb-Ag-Ca, Pb-Ag-Ti, Pb-Ag-Sn, Pb-Sr-Sn, and Pb-Ca-Sn) and quaternary alloys (Pb-Ca-Sr-Ag, Pb-Ca-Ce-Ag, and Pb-Ag-Sn-Co)[Z-4l, Although these anodes can effectively reduce the consumption of Ag, only the Pb-Co and Pb-Ag-Sn-Co anodes perform well with regard to reducing the anodic potential. However, their complicated manufacturing conditions restrict further commercial use.Besides its application in nonferrous metal electro-winning industry, Pb-based alloy is also used as grid alloy for lead-acid battery, serving as active materials supporter and current collector. In order to enhance the corrosion resistance and deep-cycling performance, reduce the impedance of the corrosion film, the addition of appropriate rare earth elements into anodic grid alloys has become a research focus. Studies proved that RE can enhance the mechanical strength of grids, inhibit the formation of anodic Pb(II) film on the surface of grids and then reduce the impedance of the film[ 10-12l."

Jan 1, 2013

By David C. Lynch

FeCl3 particulate of 10 to 100 um in diameter was reacted with radicals produced in an oxygen plasma at pressures between 1 to 20 Torr. The particulate, in a fluidized bed, was positioned above the plasma to avoid over heating the oxide product which is known to lead to crust and clinker formation[ 1 ]. Reaction between the iron chloride and the gas phase occurred at temperatures between 66 and 226 °C. Oxygen radicals react with the surface material to a depth of approximately 2.5 4m. Surface material, analyzed with a x-ray technique, indicates that the maximum amount of FeCl3 reacted on a weight basis was found to be approximately 67%. More typically, 40 to 50 wt% of the chloride was reacted within 30 minutes to 1 hour.

Jan 1, 1996

By J. C. Agarwal

Most metals are produced from minerals containing one or more of the desired metals, some contaminating metals, silicate, oxides, carbonates, and sulfides. Therefore, in the production of metals, there is generally a gaseous effluent in pyrometallurgical processes and a liquid effluent in hydrometallurgical processes. There are also solid residues such as waste ore, tailings, dust, and slag, created by the metal recovery processes. There are two important distinctions between the effluents and the residues: I. Effluents ? gases and liquids ? affect the neighboring environment for miles from the point of emission, while residues affect only the soil on which they are stored or dumped. 2. The environmental and economic effects of effluents are known and felt essentially immediately. By contrast, the environmental effects of the residues may not be known for a long time. For these reasons, the economic impact and the potential corrective actions required are very different for effluents and residues.

Jan 1, 1992

By T. W. Gonzales

The refractory performance of Peirce-Smith converters is considered to be mainly determined by effects of process control and refractory installation design. BHP Copper has shown that, over the last four years, considerable improvements in tuyere line life can be affected .by maintaining a uniform temperature in the operating converter and by ensuring sufficient and specific placement of expansion allowance in the construction of the refractory brickwork. A combination of optimized crane availability, rapid matte transfer, converter operating practices, new refractory installation techniques and applications has minimized out-of stack time. In addition, larger diameter tuyere pipes and hard piping have increased blowing rates and lowered cycle times, which has resulted in a tuyere line performance in excess of 62,500 tonnes of blister copper before maintenance is required. This paper discusses the refractory installation design changes that were made to increase tuyere line life.

Jan 1, 1999

By Jeffrey L. Zelms

Environmental issues and how they are addressed -- or not addressed -- by the lead industry in the 1990s will determine the eventual fate of lead mining in both the U.S. and worldwide. Clearly, governmental regulation throughout the West will become harsher. Equally clearly, the industry has? failed to educate the public regarding lead. Instead of public support for a critical mineral, we face widespread public ignorance and paranoia. If we can demonstrate the public interest benefits of the industry, the 1990s will be a decade of continuing growth -- not dynamic growth, certainly, but growth at least comparable to the world economy. If, however, we fail to demonstrate the industry's public interest benefits, the 1990s could mark the beginning of the end of our business.

Jan 1, 1990

By Gervais Soucy

During mineral and industrial processing, contaminated wastewater can be generated such as cyanide liquors (free species or in complex form). This paper presents the treatment of cyanide solution derived from the aluminum industry, by direct contact of the solution with thermal plasma in a novel reactor. The reacation energy is provided by a plasma submerged in solution which allows direct contact between the plasma and the solution to be treated. The scope of this' study was to determine the feasibility of treating free and complex cyanides in solution through mini-pilot scale operations. An innovative reactor was designed and fabricated to provide stable: process operating conditions. Many parameters were studied. These experiments permitted the evaluation of the kinetics of complex cyanides decomposition under thermal plasma conditions. At atmospheric pressure (temperature about 100°C), the rate of cyanide decomposition by thermal plasma was 12 times greater than that of thermal hydrolysis in a plug flow reactor et the same temperature. The improvements in the decomposition rates are attributed to high thermal gradients at the plasma liquid interface and photocatalysis induced by the plasma UV radiation.

Jan 1, 1998

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

"The effects of five commercially available foaming reagents (range of 0 to 25 ppm) namely Dowfroth 250, Saponin, Yucca, Licorice and Meta-Para Cresol on acid mist control, current efficiency, polarization behavior, and deposit morphology and orientation were investigated. The deposition was carried out using a bench scale electrolysis apparatus (cell volume 3L) at 500 Nm-2 and 38°C for 3 hours from Kidd Creek zinc electrolyte. The acid mist control capability of the various reagents was studied and compared by characterizing the foam layer generated during actual electrowinning conditions and by direct quantitative measurements of acid mist levels on top of the electrowinning cells. Within the range considered, the addition of these reagents reduced the current efficiency, refined the grain size of the deposit, and changed to preferred orientation of most of the deposits. Among the reagents tested, acid mist measurements indicated that Licorice and Dowfroth 250 were the best acid mist suppressant at emissions of 0.30 mglm3 and 031 mg/m3 respectively while Yucca and MPC produced the most mist at 3.0 mg/m3 and 33 mg/m3 emission rates, respectively.IntroductionMost of the world's primary zinc is produced via a combined roast-Ieach-purificationelectrowinning process. Depending on the electrolysis conditions, several additives may be added to the electrolyte. Some (e.g. glue, antimony, sodium carbonate) are added to mainly counteract the detrimental effects caused by impurities while others (e.g. licorice, Saponin) are used as foaming reagents to prevent excessive acid mist formation. Acid mist emission is a problem in many electrolysis operations because it corrodes the equipment and is a health hazard to the workers in the tankhouse as well as it pollutes the environment. Due to recent trends towards more environmental protection and more stringent in-plant hygiene, there is an increasing need to minimize these aerosols. In order to eliminate or minimize these aerosols foaming agents are usually added to the electrolyte to produce a foam layer on top of the electrolyte, thus trapping most of the mist. The ideal foaming agent would trap all of the mist and would not interfere with the electrowinning process. It is also evident that the reagent toxicology, cost and availability are important factors that need to be considered.Review of the available literature clearly indicated that very little work has been done in the past on the subject of acid mist control in electrowinning operations particularly in the area of foaming and anti-misting properties of surfactants. Two papers [1,2] have reviewed briefly the existing technologies for acid mist control. Recently, most of the work in this area has focused on the development of special mechanical devices that could be attached to the electrodes and control the mist generation at the source before it is emitted to the cellhouse [2-5]. On the other hand, extensive body of literature exists that deals with the effects of anti-misting reagents on the electrowinning aspects [6-7]."

Jan 1, 1997

By Zhongming Ren

"A new process of near net shape continuous casting of metal pipe has been put out. The specialty of the process is that no inner core is used. The principle of the process has been presented, and the effect of several factors on the thickness of the pipe has been investigated experimentally and numerically. It is shown that the temperature and the level of the molten metal, cooling intensity of the mold, and the velocity of casting influenced the thickness of the pipe apparently. In order to improve evenness of the thickness of the pipe, the mold was dedicatedly designed, and special methods were taken. By this process, a metallic material like ""bamboo"" was fabricated.IntroductionMetal pipe is a widely used material. Up to now, many processes have been put out to produce the pipe. However, the processes are usually expensive and inefficient. For instance, the welding pipe, which is most widely used, is produced through continuous casting of slab, rolling of the slab into sheet, and welding, with several times of heating and processing. Continuous casting of pipe can not produce small diameter of pipe, which is mostly needed, due to the inner core. Even though. OCC process is novel in fabricating the pipe with small diameter, it is inefficient. In this paper, the no-inner core continuous casting of pipe was proposed. With this process, pipe with small diameter can be produced efficiently. The influence of several parameters on the thickness and evenness of piper wall. With this process, a ""bamboolike"" pipe was fabricated.ExperimentThe experimental apparatus is shown in Fig. I. It is composed of mold, furnace, melt level adjuster, and dummy pipe. In the process, the level of the melt was adjusted at a proper position, then the mold along with the dummy pipe was inserted into the melt in a certain depth. The melt in the mold began solidifying, forming a solid shell. After that, the dummy pipe was pulled upward in a certain speed, drawing the solid shell out of the mold. Thus, a pipe was continuously cast."

Jan 1, 2000

By Yoshiyuki Matsui

As one of the factors of frequent troubles on iron-making blast in recent years, increased size of the blast furnace and high-productivity operation are pointed out. Consequently, great importance is attached to deadman shape and solid flow at the lower part of furnace. In the present study, firstly, the blast furnace raceway formation under the intensive coal injection by measurement of micro wave reflection gunned through a tuyere is discussed. As the flow rate of coke as the momentum of coke into raceway decreases by combustion of coal injected into tuyeres, the depth of raceway defined as the maximum position of micro wave reflection is easy to contract. It is expected that this new technology could detect the raceway collapse phenomena in short time and that the stability of raceway in coal injection is different from that in all coke operation. Secondly, the reduced stockline surface profile was measured by the reflection intensity of microwave struck from the furnace top after blow-off with stockline reduced, and investigation was made on the countermeasures for changes in the raceway depth and furnace body profile during operation. As a result, it has been clarified that flow-down of coke into the lower part of blast furnace and inflow into the raceway are greatly subject to the existence of deadman which is the packed structure of the lower part of furnace, and further, they are closely related to dynamic behavior of the raceway, and affect changes of the furnace body profile.

Jan 1, 2006

By E. A. Trillo, L. E. Murr, R. D. Flores, J. C. McClure, B. M. Nowak

Complex vortex and swirl-like solid-state flow phenomena have been observed in the residual microstructures characterizing the friction-stir welding (FSW) of copper to 6061 aluminum; 2024 aluminum to 6061aluminum,2024 aluminum to 1100 aluminum, 2024 aluminum to 7039 aluminum and 2024 aluminum to 2195 aluminum. These flow phenomena are characterized by intercalation lamellae composed of dynamically recrystallized grain structures of the dissimilar metals which provide a super-plastic-like mechanism for the FSW flow in the solid state; there is no melting and temperatures at the weld center do not exceed about 0.8 TM (where TM is the absolute melting temperature (K)). In experiments to be described and illustrated, optical or light metallography (LM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques are utilized in examining residual FSW microstructures corresponding to tool rotation (stirring) speeds ranging from 400 to 1200 rpm, and traverse (or actual welding) speeds of 1 to 2 mrn/s.

Jan 1, 1999