Search Documents

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By Lu Lin, Yan-ping Bao, Min Wang

In order to forecast the cost of dephosphorization during BOF process, and achieve economical dephosphorization of BOF. The mathematical model of dephosphorization cost for BOF process was established. The model calculations show that, when the silicon content and phosphorus content are increased in hot metal, and the final phosphorus content of BOF is decreased, the dephosphorization cost will be increased. The silicon content of hot metal is increased of 0.1% in the plant, the dephosphorization cost is added by 9 RMB/ton steel. The De-P cost of mode A is much higher than the other two modes for three typical production modes of single slag melting process, when the phosphorus content of hot metal is higher than 0.14%, an increase in the phosphorus content by 0.01%, the De-P cost of mode A is added by about 7 RMB/ton steel. Meanwhile, when the phosphorus content of hot metal is lower than 0.165%, the De-P cost of mode C is higher than mode B’s. For BOF single slag melting process, the dephosphorization cost calculated by model is between ± 2%, proving that the model is reliable for the prediction of dephosphorization cost.

Jan 1, 2015

By T. Asahina, M. Nakamura, M. Mabuchi, I. Shigematsu, M. Nakanishi, G. Yamauchi

"Commercial stainless steels (SUS304L and SUS430) were subjected to equal channel angular extrusion (ECAE) at room temperature to a total strain of 2.3 to 9.2. For each type of stainless steel, it was shown that the sample processed by ECAE showed higher room temperature strength than the as-quenched sample. This is probably due to the heavily worked structure. On the other hand, both strength and elongation of the ECAE processed SUS430 were increased by annealing at 773K. It is likely that higher strength is attributed to both the heavily worked structure and fine substructures. It is also likely that higher elongation is attributed to the fine substructures. It is concluded that ECAE is available for improving the room temperature strength of commercial stainless steels.INTRODUCTIONEqual channel angular extrusion ( ECAE ) is a technique that provides the repetitive deformation and allows to high intensity of deformation. With this procedure, a sample is pressed through a channel that has an equal cross section but bent at an angle of ?> [1-2]. Shear strain is introduced when a sample passes through the bending point of the channel. Repetitive processing is feasible because the cross-sectional dimension of a sample has no change during processing. To date, many reports have described that ECAE is available for the fabrication of fine-grained materials [3-14]. On the other hand, an ECAE processed sample can achieve high intensity of deformation through repetitive deformation. According to the equation given by Segal [ 2 ], a strain of about 1 is introduced in each pass through die if the angle ? is 90 deg.It is well known that high tensile strength can be achieved in metallic materials through work hardening [15]. It is also known that metallic materials with fine grain size show high strength [16]. Hence, it is expected that ECAE is available for strengthening method in metallic materials. In the present paper, we will report the mechanical properties of stainless steels processed by ECAE. As samples, SUS304L austenite stainless steel and SUS430 ferritic stainless steel were chosen. Each alloy has a single-phase structure (fee or bee) and shows no phase transformation, so that transformation strengthening cannot be applied. Hence, a heavy cold work such as ECAE may be effective for strengthening of this stainless steel. Annealing was conducted for the ECAE processed SUS430 to vary its microstructure. Then, the effect of annealing on the strength of the ECAE processed SUS430 was also investigated."

Jan 1, 2000

By G. Taylor, S. Bounds, G. Moran, M. Cross, K. Pericleous

"A variety of interacting complex phenomena takes place during the casting of metallic components. Here molten metal is poured into a mould cavity where it flows, cools, solidifies and then deforms in its solid state. As the metal cools, thermal gradients will promote thermal convection which will redistribute the heat around the component (usually from feeders or risers) towards the solidification front and mushy zone. Also, as the evolving solid regions of the cast component deform they will form gap at the cast-mould interface. This gap may change the rate of solidification in certain parts the casting, hence affecting the manner in which the cast component solidifies. Interaction between a cast component and its surrounding mould will also govern stress magnitudes in both the cast and mould - these may lead to defects such as cracks.This paper presents a multiphysics modelling approach to this complex process. Emphasis will be placed on the interacting phenomena taking place during the process and the modelling strategy used. Comparisons with plant data are also be given."

Jan 1, 1999

By M. Yoshida, S. Hanada, T. Takasugi

"A study has been conducted to examine the effect of ternary alloying elements on high temperature deformation of the C15 NbCr2 based intermetallics in Nb-Cr-X (X=V, Mo and W) alloy systems, which have attractive properties as high temperature structural materials. The high temperature deformation of the C15 NbCr2 intermetallics can be improved by two alloying methods. One method is based on geometrical consideration for site occupation and atomic size factor of component elements and additive elements in the single phase C15 lattice; addition of Mo and V can promote dislocation movement without introducing significant hardening. The other method is based on microstructural modification through ternary alloying; moderate addition of these elements results in a variety of duplex microstructure consisting of the C15 phase and bee solid solution without forming any intermediate phases, and can enhance the high temperature deformability. Particularly, alloys with duplex microstructure equilibrating with Cr-rich bee solid solution is shown to exhibit superior deform ability. Also, lattice property of the additive atoms in the C15 structure and phase relation between the C15 structure and the bee solid solution are investigated by OM, XRD, TEM and ALCHEMI observations and then discussed in association with observed mechanical behavior.IntroductionLaves intermetallics with AB2 stoichiometry belong to the largest group in a large number of intermetallics with various kind of crystal structures, and have a variation of the cubic CIS, the hexagonal C14 and the dihexagonal C36 structures, depending on stacking sequence of XYZ type, each of which consists of four interpenetrating atomic layers (1-3). Some of the Laves intermetallics have good functional properties and therefore are considered to be used as, for instance, magnetic materials, magneto-optical materials, hydrogen storage materials and superconducting materials (2). Also, the Laves intermetallics are considered to be good candidate as high temperature structural materials operating at high temperatures and in severe environment because they have high melting point, low density, and potential resistance to corrosion and oxidation. However, the Laves intermetallics are very brittle at low temperatures because they consist of complex crystal structures similar to many other intermetallics."

Jan 1, 1996

By P. Tapp, T. Evans, N. A. Molloy, J. Lucas

"Consideration of the protoype tuyere geometry for injection of inert gas through the bottom in a basic oxygen steel furnace and a requirement to specify an optimal flow for bottom wear and metal penetration led to experimental investigations[l,2] to apply the results of previous workers to this specific case, Flow velocity profile development within the tuyere was proposed as significant and the experimental scheme was designed to test this. It is proposed that the design criterion for the conditions of optimal flow of the prototype geometry be based on the non-dimensional mass velocity.INTRODUCTIONSharma[3] tested small diameter tuyeres in a laboratory hot model using molten iron to define a flow criterion for prevention of penetration of the bath liquid into the tuyere. Using argon, nitrogen and helium through a range of tuyeres (1 to 3 mm ill ) he proposed the jet Froude number C Fr' ) with the critical value being 2400 - 2500 or higher. Sonic or supersonic velocity was not a sufficient criterion. The tuyere design was a parallel tubular duct of moderate aspect ratio CAR) i.e. the ratio of length to diameter ranging from about 22 to 36 in the experimental furnace.Farmer et al[4] stated their their aim ""to develop a unifying explanation and procedure for the proper design of tuyeres"" but disagreed with Sharma's jet Froude number criterion. Recalculating Sharma's data they proposed instead a fully expanded Mach number of 1.75 with an initial expansion angle of ten degrees as the lower bounds of flow to meet the design requirement. They experimented with tuyeres in a water model using tubular, annular and convergent-divergent nozzles. The aspect ratio of the parallel duct tuyeres was from 533 to 762 using diameters of 1.4, 1.7 and 2.0 mm C the diameters being of tubes to be used full scale). Subsequently these results were applied to a prototype tuyere using a diameter of 1.7 mm with beneficial results in practice. This tuyere had an aspect ratio of 1067."

Jan 1, 1996

By Peng ZANG, Qihang Liu

Experimental work was conducted to determine the relationships of coal char conversion with temperature and heat absorption. The results show that at an earlier stage of the coke forming process, lump coal would absorb large amounts of heat but the increase of high temperature strength of lump coal was not significant. Contrarily, the lump coal’s high temperature strength was greatly improved at later stage of coke forming process. A number of residual coal was found in most tuyere coke samples illustrating that the lump coals added in the melter gasifier were not completely transformed into coke when they arrived at the tuyere region. The results indicate that the improvement of lump coal’s high temperature performance is limited in the melting gasifier by the low coke forming rate which could become the core factor of fines generation of lump coal in the melting gasifier.

Jan 1, 2016

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"In China, hazardous e-waste—cathode ray tube (CRT) glass is usually left around, and it is likely to contact with water resources directly. To identify the real leaching characteristics and bioavailabilities of heavy metals Pb and Ba contained in CRT glass in the nature environment, experiments were carried out by simulating the nature environment. The results indicated that Pb and Ba contained in CRT glass were stable in most conditions, which only showed obvious leaching toxicities in strong acidic/alkali conditions. EDTA and DTPA extractable Pb and Ba amounts were extremely high, e.g., EDTA extractable Pb of color funnel glass was up to 1960.07 ìg/kg, indicating that the potential bioavailability of waste CRT glass is very high. IntroductionIn recent years, cathode ray tube (CRT) contained monitors or TV sets has been substituted by novel and better electronic and electric equipments such as LCD and PDP, leaving huge amounts of end-of-life CRTs. 50~85% of the total weight of a computer monitor or a TV set is glass'1-21, which was classified to three categories: black & white glass (BW), color panel glass (CP) and color funnel glass (CF), according to their chemical compositions'3' (Méar et ai, 2006). In order to provide shielding from X-rays generated during the picture projection process, lead, barium and strontium oxides were used in the glass. In general, a color CRT contains 1.6-3.2 kg of lead'4'. Concerning the high toxicity of lead, these waste glasses have posed a potential risk to the environment and human health and researches on these glasses have been attracting wide and tense attention currently."

Jan 1, 2011

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the furnace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By James C. Sever

"With the advent of high energy costs and increasing concern for the environment leading to the incorporation the C02 life cycle as a criteria for the material used in a finished product, it is beneficial to analyze the plant and the process used in producing a raw material in order to identify practical, economic energy recovery opportunities. To this end a study was made of the proposed Nevada Clean Magnesium, Inc. Tami-Mosi reduction facility. Each source of waste heat is listed together with the assessment for potential co generation or direct recovery. The overall impact on energy requirement and C02 generation is provided.IntroductionHistorically metal reduction plants, large consumers of energy, do not recover waste heat. This occurred for many reasons:• Energy costs were low and the capital for a co-generation system could not be justified;• Waste heat sources contained entrained solids or liquids which would inhibit efficient energy recovery;• The exit temperature for the heat source was too low for efficient use by aaqueous Rankine cycle system.The business environment has now changed adding impetus to the recovery of energy previously discarded. Power costs have greatly increased. Global warming and the impact of carbon dioxide on the environment has become an issue which could impact the permitting of a plant. Technology improvements especially the development of a scaling environment waste heat boiler [l] and the development of the organic cycle Rankine cycle recovery system enable up to 70% energy recovery from ""low grade"" heat sources [2].With the inception of Nevada Clean Magnesium, Inc. 's (formerly Molycor Gold Corporation, Inc.)Northern Nevada Tami-Mosi project [3], an opportunity was presented to incorporate energy optimization from the initial design phase."

Jan 1, 2013

By Y. Prévost

The Noranda Continuous Converting Process was commissioned in November 1997 at the Home smelter in Rouyn-Noranda, Quebec, Canada. It has completed over 18 months of successful operation. Excellent team work and technical expertise contributed to achieve targeted production levels and environmental goals after only a few months of operation. The operating results have demonstrated the flexibility of the process in producing blister copper from a variety of copper feed materials including a combination of molten and solid copper matte, reverts and fluxes. This paper describes the startup activities and process optimization tasks performed during the first year of operation of the new Noranda Converter.

Jan 1, 1999

By Che Xin, Liu Tianlong, Bi Hongyun, Chen Lijia

"High-cycle fatigue experiments were conducted at 800°C in laboratory air for three ferrite stainless steels including 15CrNbTi, 15CrMoNbTi and 18CrNbTi, where the stress ratio of 0.l was adopted. The experimental results show that at 800°C, the fatigue limit of the 15CrMoNbTi steel is the highest, the fatigue limit of the 15CrNbTi steel is slightly lower than that of the 15CrMoNbTi steel, and the fatigue limit of the 18CrNbTi steel is the lowest. At the same maximum stress, the 15CrMoNbTi steel has longer fatigue lives than the 15CrNbTi steel in the low stress area, while the 18CrNbTi steel has the shortest fatigue life. In addition, the observations on the fracture surfaces of fatigue specimens reveal that the fatigue cracks initiate transgranularly at the free surface of the specimens and propagate in a transgranular mode.IntroductionIn modem automotive industry, the manufacturers have paid great efforts to clean exhaust gas and to improve fuel economy. It is thought an effective way to increase the temperature of combustion chamber in automotive engine. And thus, the manifold closed to the engine in automotive exhaust system can suffer high temperature up to approximately 1000°C. Because of their relatively low thermal expansion coefficient, high yield strength at elevated temperature and good fatigue resistance, ferrite stainless steels, especially added with alloying elements such as Mo, Nb and Ti, are increasingly used for automotive exhaust systems [1-3]. In fact, exhaust manifold operated under high frequency vibration and exposed to high temperature exhausting gas also requires good fatigue resistance at elevated temperature. Some studies on the high temperature fatigue characteristics of stainless steel have been documented. It has beeen found that the fatigue limit of four ferrite stainless steels including 409L, 436L, 429EM and 444 (18Cr- 2Mo) reduces significantly with increasing temperature [4, 5]. In the research concerning the effect of a-phase embrittlement on fatigue behavior in a high-chromium ferrite stainless steel, it is noted that the precipitation of brittle a-phase will reduce the crack initiation and growth resistances and result in a decrease in fatigue limit [6]. In this investigation, the high-cycle fatigue behavior of three ferrite stainless steels including 18CrNbTi, 15CrNbTi and 15CrMoNbTi at 800°C have been studied to address the mechanical aspect of high-cycle fatigue behavior for ferrite stainless steels and to provide the theoretical reference for the safe design of automotive exhaust system."

Jan 1, 2013

By Nils Eivind Kamfjord, Mari K. Næss, Gabriella M. Tranell

"In oxidative ladle refining (OLR) of silicon, the metal surface is oxidized resulting in the formation of a condensed silica fume (SiO2). In the current work, industrial measurement campaigns were performed aiming to measure the fume generation during OLR. A thorough discussion of the possible mechanisms has been included in order to improve our understanding of the Si(1)-O2(g) system.The measurement campaigns were performed at the Elkem Salten plant in Norway. In addition to fume generation from OLR, the metal temperatures and ladle purge gas amount were recorded. The results of this work suggest that fume generation during OLR results from splashing of the metal and/or oxidation of the metal surface, with oxygen transport to the metal surface being the limiting factor. Other mechanisms of SiO2 formation were investigated, however insignificant.IntroductionOne of the main environmental and economical challenges facing the metallurgical industry is fugitive emissions of both materials and energy. In the production of metallurgical grade silicon (MG-Si), refining of the silicon generally takes place through an oxidative ladle treatment (purging with an air-O2 mixture). In the refining process, exposure of silicon to air results in the formation of condensed silica fumes (SiO2) – one of the main sources of fugitive emissions in silicon production plants. The oxidation of liquid silicon, as opposed to solid silicon, has not been widely studied and described in the literature [1], thus a thorough investigation of the oxidation mechanisms, and factors affecting the oxidation reaction rate are essential in order to deal with the problem. In the current work, the rate of liquid silicon oxidation has been studied through industrial measurements of fume generation from refining adles, where the purge gas rate and composition have been varied. The results from these measurements were discussed in light of existing models describing the liquid silicon oxidation kinetics."

Jan 1, 2011

By Gerald Onyedika, Tochi Onwumere, Martin Ogwuegbu

"The kinetic study for the leaching of iron from cassiterite ore in KOH solution was studied. The effects of KOH concentration, particle size and reaction temperature on the leaching rate of iron were also examined. The results of leaching studies showed that the leaching of iron from cassiterite ore in KOH solution is significantly influenced by the reaction temperature, KOH concentration, and decrease in particle size. The study showed that 90.62% of iron ore was leached in 8M KOH solution at 80°C within 120 minutes. The experimental data were well evaluated using the shrinking model for surface chemical reaction and diffusion control through the product layer. The activation energies for the iron ore dissolution using the two models were calculated to be 32.06KJmor1 and 97.97 KJmor' respectively.IntroductionIn recent times, there has been increasing attention on the kinetic study of mineral dissolution. In most of these studies, the experimental results were analyzed with a suitable shrinking core model under the assumption that the ore is a homogeneous spherical solid phase [1-4]. A study of the dissolution kinetics of a Nigerian cassiterite ore by hydrochloric acid showed that increase in the hydrochloric acid concentration is accompanied with increase in the amount of cassiterite ore dissolved at various times [4]. The optimal concentration was found to be 4.0M HCl, after which there was a decline in the amount of the ore dissolved, which showed that the concentration of the reagent has a significant effect on the leaching rate of the ore. Also in studying the effect of stirring speed on the rate of cassiterite ore dissolution while keeping other conditions constant for 120 minutes, the result showed that the rate of cassiterite ore dissolution was dependent on the stirring speed over a range of 0 to 630 rpm. Above 360 rpm, the stirring speed no longer had any effect on the solid dissolution. The dissolution rates of cassiterite were analyzed using a suitable shrinking model. The results showed that the reaction was controlled by the diffusion of tin through the porous product layer, a reaction order with respect to hydrogen ion concentration of 0.92 M and activation energy of 50.05KJmor'. In another kinetic study on the leaching of a low grade niobium-tantalum ore with concentrated KOH solution the effect ofreaction temperature, KOH concentration, agitation speed, particle size and alkali-to-ore mass ratio on the dissolution rate of niobium were examined [5]. The result of niobium leaching from low grade niobium-tantalum ore with concentrated KOH, solution at different agitation speeds showed that the dissolution rate increased with increase in agitation rate. In the case of particle size effect, the results show that small particles require much shorter time for complete dissolution than the large ones."

Jan 1, 2013

By L. Petitnicolas

The experimental study of nitrogen absorption and its removal from a liquid Ni-20%Cr alloy at 1873 K has been undertaken, using an experimental, apparatus based on the Sieverts technique in order to determine the solubility of nitrogen in the alloy. as well as the kinetics of nitrogen transfer across the gas/melt interface. Experiments show that nitrogen solute equilibrium content can be calculated using the Sievens law. Measurements point out the nitrogen absorption reaction rate to be well described by first order kinetics, whereas experiments on nitrogen removal reveal that the rate is better expressed using a second order equation.

Jan 1, 1996

By Eric J. Grimsey

Steady state Excel models for a copper flash smelter and an iron blast furnace are used to enhance the teaching of pyrometallurgical smelting principles within a fourth year level process engineering unit delivered at the Western Australian School of Mines. A lecture/workshop approach has been adopted in which student teams undertake process simulation assignments that illustrate the multifaceted responses of process outputs to variation of inputs, the objectives being to reinforce their understanding of smelting principles. The approach has proven to be popular with students, as evidenced by the consistently high ratings the unit has received through student feedback. This paper provides an overview of the teaching approach and process models used.

Jan 1, 2014

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By Y. Y. Sheng

Plume flows created by gas injection into liquid metals have been studied extensively, however the dynamics of bubbles within the plume have not received adequate attention, particularly for large, irregular bubbles, characteristic of the processing of liquid metals. The present model uses a combined Eulerian-Lagrangian approach in which an estimated void fraction distribution is used to calculate the liquid flow field with a conventional Eulerian scheme. The trajectories of bubbles are then computed in a Lagrangian manner using the estimated flow field, and experimentally measured information on bubble drag coefficients', lateral migration due to lateral lift forces and interaction with turbulent eddies, and variation in bubble size due to break-up. Turbulence in the two-phase zone is modeled with a modified k-e model with extra source terms to account for the second phase which have been recently determined by the present authors. The computed void fraction and turbulent liquid flow field distributions are in good agreement with experimental measurements.

Jan 1, 1993

By Michael L. Free

Bacterial oxidation of an arsenopyritic gold-ore .concentrate was carried out with continuous-flow .operation in 14-liter, mechanically agitated reactors. Samples from the slurry reactors were separated into solid and liquid fractions and analyzed separately to determine the electrochemical rates of sulfide conversion by the bacteria and the rates of direct bacterial oxidation of sulfide. The rates of the individual mechanisms are compared to the overall rates of biooxidation in the continuous-flow slurry reactors. The results show that the commonly hypothesize4 direct and indirect mechanisms of biooxidation both play a significant role in the bacterial oxidation of sulfide ores.

Jan 1, 1991