Search Documents

By Stella Agatzini

Column leach tests were conducted to evaluate the amenability of poor Greece nickel laterites to heap leaching with dilute sulfuric acid at ambient temperature. The ore tested was a limonitic laterite with less than 1 % nickel and it was subjected to a suitable pretreatment with water prior to it being loaded into the columns, following findings of preliminary research work. The acid solution was recycled after suitable pH adjustment. Factorial designs were used to determine the effects and interactions of the following factors: sulfuric acid concentration, ore column height, ore grain size and ratio of leach solution volume to the ore quantity. The response which were investigated included nickel and cobalt recoveries, codissolution of iron, calcium, magnesium, aluminum, chromium and silica and also sulfuric acid consumption. Experimental error was also detennined. The tests showed that a nickel recovery of 88% could be achieved in 60 days.

Jan 1, 1993

By Massoud Hassanabadi

Filtration using Ceramic Foam Filters (CFFs) is a method widely used to separate inclusions from molten aluminium. In the present work, the specific permeability and form drag coefficients of nominal 50 mm thick commercial Al2O3- based CFFs, of grades 30, 50, 65 and 80, have been calculated from pressure drop experiments using high (60–500 mm s−1) and low (0.2–10 mm s−1) water velocities. Moreover, 2D axial symmetric Computational Fluid Dynamic (CFD) models have been developed, using COMSOL Multiphysics® to validate the experimental results. The empirically obtained values were defined as global parameters used to model the pressure, as well as the velocity fields in the water pipes and in the CFFs. The modelled pressure drop over the filter thickness for the high water velocity experiments showed < ± 1% deviation from the corresponding experimental results for all CFF grades. Moreover, the developed model also showed good agreement with the experimental results obtained from the low water velocity experiments, where the deviation of the pressure drop for the CFF samples of grade 30, 50 and 65 were ≤ ± 4.6% and for CFF samples of grade 80 ≤ ± 13.4%.

By R. P. Rao

In rare earth (RE) based phosphors, high luminous efficiency is possible due to their restricted emission limited to specific narrow bands. In general, these phosphor materials consist of RE ions as activators/sensitizers and/or hosts. Development of various phosphor host matrices such as alkaline earth chlorophosphates, aluminates and silicates activated by Eu(2+) as blue component, borates and phosphates of lanthanides and alkaline earth aluminates doped, with Ce/Bi and Tb as green component and Eu(3+) activated yttrium oxide and vanadate as red component has been described. Luminescent characteristics, color coordinates and suitability of these phosphor materials in high efficiency new generation lamps are presented and discussed.

Jan 1, 1989

By Alex Probst

With low metal prices and increasing value placed on plant water and tailings disposal areas, it is becoming essential to maximize the efficiency of solid-liquid separation processes. Since its inception over 25 years ago, the use of flocculants has grown exponentially. While flocculants play a crucial role in the sedimentation process, they are also a major operating cost. Recent innovations are revolutionizing the industry once again. New thickener designs are doubling thickener-loading rates while reducing flocculant consumption. The feedwell, as the heart of the thickener, is undergoing many significant metamorphoses. With CFD and other advanced computational analysis, feedwell technology is being examined more thoroughly than ever before, The result is that the thickener previously thought of, as a "Black Box" is now being mapped and controlled with state-of-the-art technology. This paper will examine recent design improvements in all aspects of thickeners in order to project the look of the thickener of tomorrow.

Jan 1, 1999

By Anastasia Alksnis

Pyrrhotite is an iron deficient, low nickel content sulfide mineral that is commonly associated with pentlandite, a nickel-rich sulfide; and are both main components of the nickel ore mined in Sudbury. Pyrrhotite tailings generated in the concentration of Ni ores are stored in tailing reservoirs and presents serious environmental risks including acid mine drainage. This study investigated the potential of converting pyrrhotite into a valuable resource through the use of fluidized bed roasting, in which the mineral will be oxidized to produce iron oxide and SO2 gas. These products can then be used to create iron for high-grade steel and elemental sulfur. Thermogravimetric analysis of Sudbury pyrrhotite was performed to study the oxidation kinetics, supporting the feasibility of this process. Further, energy and materials balance was carried out to establish the basic parameters of a possible roasting process.

By He Jing, Wang Changhong, Chen Yongming, Wu Yanzeng, Yang Xiyun, Tang Chaobo, Yang Shenghai

Pitting of Hf in Et4NBr t-butanol and acetonitrile (ACN) solutions was studied by means of cyclic voltammetry, potentiodynamic anodic polarization,galvanostatic, potentiostatic and impedance techniques. The potentiodynamic anodic polarization curves did not exhibit an active dissolution region near corrosion potential due to the presence of an oxide film on the electrode surface, which was followed by pitting corrosion resulting from the passivity breakdown by the aggressive attack of bromide (Br−) ion. The pitting potential (Epit) increased with increasing potential scanning rate but decreased with increasing temperature and Br− concentration. Cyclic voltammetry and galvanostatic measurements allowed the pitting potential (Epit) and the repassivation potential (Ep) to be determined. Analysis of the potential/time transients revealed that the applied anodic current density had a significant influence on the values of Epit. On the other hand, the Ep values were independent on the applied current density. The current/time transients indicated that the incubation time (ti) for passivity breakdown decreased slightly with increasing potential and solution temperature. The impedance spectra showed that the resistance of passive layer decreased with increasing potential.

Mar 1, 2017

By B. Manana

In heap leaching, the oxidative dissolution of value minerals encapsulated deep within large particles cannot be fully understood on the basis of the bulk solution conditions relative to variable solution conditions near the mineral surface. In the present study, the diffusion of the oxidising species through inner particle pores is simulated in a model apparatus that separates an inert platinum electrode under controlled reduction potential from the bulk solution through narrow pores of varying length. The Cu-NH3 system was selected as a model system and Cu(II)/Cu (I) as the redox couple of interest. Platinum probes inserted in the pores allowed the measurement of varying redox potentials along the pore length. Results showed that in a 10 mm pore, there exists a narrow (0.5 mm) zone near the reduction surface that is depleted of the oxidant and in which its supply is strongly diffusion limited, even if it is in abundance in the bulk solution. The consistent presence of this narrow diffusion region across all experimental results indicated that the transportation of the reduced species away from the reaction surface had the most significant influence on the potential variations within the pore. This was further supported by the minimal effect of varying concentrations of both Cu(II) and dissolved oxygen on the solution potential within this region.

By Raj Mutharasan

The phenomena of gas-molten metal reactions for the production of metal matrix composites consist typically of a combination of one or more gas transport steps and a liquid gas reaction step. Reaction products include such strength enhancers, grain refiners, or high thermal conductivity phases as TiC, AIN, SIC, Si3N4, TiN in aluminum alloys. Nitrides, carbides and oxides can be produced at various volume fractions and in fairly fine sizes (500 am to 5 um) in laboratory melts by Reactive Gas Injection method (RGI). Gas injection methodology to produce the reinforcements is attractive because it can potentially be scaled to production scales in excess of 10,000 kg/h. For continuous production, the reactant molten metal can be continuously fed into the .crucible where the reactive gas is injected. The molten metal phase reactant may also be involved in a controlling transport step, depending on its concentration and viscosity. It is well known that the reaction product reinforcement size and shape of these phases have significant impact on the physical, mechanical and thermal properties. The current state of knowledge is unable to predict the kinetics and growth of solid reaction products obtained. The primary goal is to develop a fundamental framework for the understanding and prediction of the particle size in such reaction systems. In addition, the role of gas transport, liquid hydrodynamics and decomposition are important issues. A reaction-transport model is being developed using a reaction, transport, and thermodynamic framework, both at macro and at atomistic level to assess gas - liquid interactions.

Jan 1, 1996

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Jie Qiu, Yun Chen, Kai Tang

Isothermal reduction kinetics of CF2 by 30% CO and 70% N2 at 1123, 1173 and 1223 K was investigated by TGA in this study. The reduction rate analysis indicated that reduction of CF2 comprises three stages during the whole reduction process, Apparent activation energy of samples CF2 reduction is 34.37 kJ/mol. The ln-ln analysis implied the reduction of CF2 was expressed initially by a 2D subsequently by 3D shrinking layer reaction.

Mar 1, 2017

By F. Raupp-Pereira, G. G. Cunto, J. A. Junkes, D. Hotza, V. P. Della

"The present work investigated the valorization of wastes as alternative raw materials for ceramic industries. Different industrial wastes based on the SiO2-Al2O3-CaO system and classified as non-hazardous were selected: sludge from varvite cutting process, sludge from gneiss breaks processes, sludge from filtration/clarification of potable water and a clay classified also as waste. All as-received residues were characterized by X-ray fluorescence, differential thermal analysis, thermogravimetry and particle size distribution. The applicability of these materials in ceramic formulations was then evaluated. The formulated mixtures were subjected to forming by pressing and extrusion followed by thermal treatment. After optimization of the processing conditions, the properties of the samples sintered at different temperatures were also evaluated. The waste materials studied proved to be alternative raw materials to natural mineral resources for the ceramic industry.IntroductionOne of the most important problems that have accompanied the humanity in recent decades is the environment’s degradation. In the same context, the natural resources exploration and technological development are phenomena which, if aren’t controlled, can cause ecological disequilibrium with unpredictable consequences [1]. It is in this perspective that recycling of various wastes assumes relevant importance.The recycling, understood here as the waste process reuse, is a common practice in the First World countries, where the raw materials have strategic aspects and the disposal techniques of solid wastes have considerable economic costs. In Brazil, the ecological conscience begins to be aroused due to, in the last ten years, the implementation of stricter laws for environmental control, in general, and licensing of waste generating from industrial activities, in special. The terms “residue” or “waste” are normally used to describe what remains of a production process; when an application for this material is not found. When wastes or residues are susceptible to be incorporated as raw materials or energy sources in a new material production, they can be understood as by-products [2].The valorization of industrial wastes is important, due to the need to pollute less and give an ecologically correct destination for wastes. The waste recycling, independent of its kind, presents several advantages in relation to using primary natural resources, such as reduction in the volume of raw materials extraction, lower energy consumption, lower levels of pollutant emissions and improvement of the health and safety of the population. The most visible advantage of recycling is the preservation of natural resources, extending its life and reducing the destruction of landscape and ecosystems [3]."

Jan 1, 2008

By Jinqian Zhao, Jiarong Li, Shizhong Liu

"Creep cavitation of in single crystal (SX) superalloy was investigated. The constant load creep tests, in single crystal superalloys DD6, were conducted at the conditions of 800°C/700MPa, 850°C/550MPa and 900°C/450MPa, respectively. It was found that there were square facets on the stress fracture surface, and microscopic cavities in the ruptured specimens in the vicinity of the fracture surface. Both the square facets on the fracture surface and microscopic cavities in the section of the ruptured specimens show the morphology of the same thing at the different views, namely creep cavities, which are take the form of flatten cuboid. In fact, creep cavities are the longitudinally tensiled creep cracks slowly growing during the stress tensiling. The factors of creep cracks nucleation and growth conditions include: (a) enough high temperature to activate diffusion (b) casting pores as nucleation origination (c) high strains and strain rates. Eventually, the instantaneous fracture mechanism of creep specimen is cleavage fracture.IntroductionFor the materials used in elevated temperature service, creep behavior has to be accounted for. It is well recognized that creep rupture in polycrystalline materials at high temperature occurs principally by the nucleation and growth of microscopic cavities at grain boundaries, followed by microscopic cavities linkage to form micro- and eventually macro-intergranular cracks[l,2]. Without the usual grain boundaries, SX superalloys have superior capabilities at high temperatures to polycrystalline superalloys, and have become an established feature of gas turbine technology where they are commonly employed in the manufacture of high performance blades[3]. A considerable amount of work has been done over the past tens of years, and many models for nucleation and growth of creep cavities have been proposed, however, those are mainly for polycrystalline materials.In order to improve creep resistance that single crystal superalloys, in which grain boundaries are removed, have been developed. Because there don't exist grain boundaries in SX superalloy, the mechanism of nucleation and growth of creep cavities must be different from that in polycrystalline materials.Understanding the formation and characteristics of creep cavitation is crucial to model the lives of single crystal superalloys.M. Marchionni and L.G. Zhao et al. found that there were square facets on the stress fracture surface [4,5]. Roger C. Reed pointed out creep cavities lie in the necked region[6]. In this paper, the effects on the formation of creep cavities are discussed, as well as the morphology of creep cavities and fracture mechanism of SX superalloys."

Jan 1, 2013

By Nobuaki Sato, Tetsuo Fukasawa, Akira Kirishima

To apply the fluoride volatility process for the treatment of fuel debris formed in the damaged nuclear reactors, study on the fluorination behavior of main constituents, such as fuel and cladding is essential. The mixture of uranium and zirconium oxides is formed under severe conditions such as high temperature and oxidizing atmospheres. In this paper, fluorination and volatilization behavior of uranium and zirconium oxides have been studied by TG-DTA method in the presence of fluorine. From the TG-DTA result of UO2 in F2 atmosphere, the weight gradually increased up to 7% at 350 oC followed by rapid weight decrease with exothermic peak showing the vaporization of uranium as UF6. ZrO2 showed similar fluorination behavior to that of UO2. However, fluorination of UO2-ZrO2 seemed to be suppressed with increasing ZrO2 amount. This may be caused by the formation of solid solution.

Jan 1, 2016

By Shengping Li, Wei Lv, Gangqiang Fan, Xuewei Lv, Yingyi Zhang

The electrical conductivity of high titania slag, as being an important fundamental physical property utilized in the theoretical understanding of mass transfer phenomena and requirement of practical electric smelting processes, were measured by AC Impedance Spectroscopy using four-electrode method for ternary TiO2–FeO–Ti2O3 slag system based on 85 type of titania slag in Panzhihua in this work. The experiment results show that the slags have a high magnitude of the order of 80–180 s/cm−1 in the whole experimental temperature range from 1523 to 2013 K. The Ti2O3 exhibits very strong effect on increasing the electrical conductivity of high-titania slag since the specific values averagely increase by 55 s/cm−1 with corresponding Ti2O3 content range from 10 to 16 wt%. the X-ray diffraction gram and phases calculated by FactSage are presented and interpreted to discuss the impact of phase change on the electrical conductivity.

Mar 1, 2017

By Guanyong Shi, Zhihe Dou, Cong Wang, Ting'an Zhang, Hongyan Zhang

We prepared the CuCr alloy by thermit reduction-electromagnetic casting. But there are the defects such as stomata and oxide inclusions in CuCr alloy. In this paper, the existing state and distribution of inclusions and stomata in CuCr alloy are systematically analyzed. The alloy was characterized via SEM, EDS and metallographic microscope, in which the existing state and micro-structural defects of inclusions are analyzed. The results show that: there are three distinct areas: copper-rich areas, chromium-rich areas and the inclusion areas. Inclusions are mainly in the form of stomata and Al2O3 phase, mainly locating in the copper-rich phase and the interface area of chromium-rich phase and the copper-rich phase. Then, the composition of phases of the smelting slags and alloy were characterized via XRD. The results show that: the slag consists of Al2O3 and a little of Cr, the alloy consists of Cr, Cu and a little of Al2O3.

Jan 1, 2015

By Henrik Gudbrandsen, Anne Støre, Ana Maria Martinez, Karen Sende Osen, Ole Kjos

The light rare earth metals Nd, Pr, La, Ce as well as some alloys with Fe, are today produced in China by electrolysis in molten fluorides using oxide raw materials. A major challenge is to obtain a good cell operation without de-composing the electrolyte leading to emissions of per fluorinated carbon (PFC) green-house gases to the atmosphere. This work is focused on understanding the fundamental requirements to run the electrolysis cells for DyFe alloy production in an ef ficient and environmental friendly way. Electrolysis experiments was carried out in DyF 3-LiF melts at 1050 °C. A Fe rod was used as consumable cathode and the (consumable) anode was made of graphite. To establish at which anode potential PFC occurred and thus enabling optimisation of the oxide batch feed rate, analysis of the anode gases was performed with Fourier Transform Infrared Spectrometer (FTIR). The produced DyFe alloy was characterised by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS).

Mar 1, 2017

By F. L. Meng, C. S. Henkel, R. M. Alchalabi

For secondary aluminum producers to maintain a profitable melting operation, five technical factors have to be taken into account from the initial furnace building decision to the final operation and production. These factors are furnace design, furnace equipment selection, furnace control, furnace charge selection and inventory, and furnace operation. Any of these five factors, if not chosen or performed wisely, will likely result in sub-optimal melting operation. As a result the MeltSim melting optimization package has been developed by the collaborative effort of Chinook Sciences and AMCS Corporation to take into account these five factors. The package is a mixture of hardware, software, science and experience. The package incorporates years of reverb furnace operational observations, start-up installations, furnace operator experience and furnace physiochemical mathematical model development. The optimization package enables aluminum producers to design new furnaces, select and place proper equipment, optimize existing furnace operations, and convert air-fuel installations to oxy-fuel. The package provides furnace operation monitoring and advisory signals, and furnace automatic optimal control to furnace operators, shift supervisors and plant managers, all customized, based on plant and melter need and ease of information management.

Jan 1, 2000

By Coida D. S. Renata, Gerald Okwuchi Onyedika, Moura E. B. Esperidiana, Graca Valenzuela-Diaz, Martin Chidozie Ogwuegbu, Francisco R. Valenzuela-Diaz, Amauche Cyprian Achusim-Udenko

This work aims to incorporate Mgbee clay, vegetal fibre (Costus afer) in recycled low density polyethylene (rLDPE). The incorporation of clay and vegetal fibre in rLDPE was carried out using a twin screw extruder machine and the nanocomposites were obtained. The nano composites were characterized by the Young’s modules test, tensile tests, bending test, XRD, SEM, DSC, and TG and other properties evaluated. The results of morphological and thermal properties showed a good interaction between the clay, and rLDPE as compared to neat rLDPE.

Mar 1, 2017

By Wenxuan Xu, Shusen Cheng, Guolei Zhao

Nowadays,the flow pattern and stress distribution o burden material sin blast furnace has been widely calculated by discrete element method. In this study, the influence of operation conditions such as ore batch, the root position of cohesive zone and the slope of cohesive zone on the flow pattern and stress distribution of burden materials in blast furnace were investigated. The normal stress of burden materials in deadman increases with the increase of ore batch, but the normal stress of burden materials in deadman decreases with the increase of the root position of cohesive zone and the slope of cohesive zone. The average descending velocity of burden materials increases with the increase of ore batch, but the average descending velocity of burden materials decreases with the increase of the root position of cohesive zone and the slope of cohesive zone.

Mar 1, 2017

By Vineet Kumar Yadav, Akshay Dvivedi, Pradeep Kumar

Near-dry electric discharge machining (EDM) is a process variant of EDM, which uses two-phase flow of liquid and gas as dielectric medium. This article reports the results of an investigation pertaining to the drilling of holes on high speed steel (T2 grade) by a rotary tool near-dry EDM. The One-Factor-At-a-Time (OFAT) approach was used for experimentation. The effects of process parameters, viz. tool rotation speed, peak current, pulse duration, gas pressure and liquid flow rate on material removal rate (MRR) and overcut were investigated. The dielectric medium used was a mixture of glycerin-air. The experimental results reveal that rotation of the tool electrode along with high pressure of two-phase dielectric medium contribute in an effective flushing of inter electrode gap (IEG). Further, in rotary tool near-dry EDM process, higher values of current can be used. This improves process economics in terms of MRR. The MRR measured with rotary tool near-dry EDM was three to four times higher in comparison with conventional EDM. Additionally, appreciable surface quality was achieved.

Mar 1, 2017

By Ximena Diaz

Mercury is one of the most undesirable contaminants in gold bearing ores. During cyanidation mercury cyanide compounds accompany gold in all the extraction and recovery processes. Of course mercury in the carbon eluates creates environmental problems in subsequent refining steps. One possible process alternative for the separation of gold from mercury in such concentrated alkaline cyanide solutions is the selective solvent extraction of gold by undiluted Dibutyl Butyl Phosphonate (DBBP). In order to describe the behavior of mercury during extraction by DBBP, the results from a preliminary research program are presented. In this study, temperature and cyanide concentration have been found to be the most significant variables which influence the separation of gold from mercury by solvent extraction using DBBP. It was found, using plant eluate from a carbon strip, that excellent separation of gold from mercury can be obtained at 60&apos; C with 98% gold recovery and complete mercury rejection in a single stage of extraction. The influence of pH is also discussed in terms of the extraction chemistry. These results complement previous research which described the DBBP solvation extraction of an aurocyanide ion pair. In addition, these results extend our understanding of the alkyl phosphorous ester extraction systems by illustrating that neutral ionic species such as Hg(cN)02sq, can be extracted at low cyanide concentrations, a phenomenon which had not been observed previously for other cyanoanions.

Jan 1, 1993