Search Documents

Tailgate pillar and tailgate-face corner humps have been a major threat to longwall coal mines where hump-prone conditions exist. The yield pillar design concept, in which the longwall chain pillars are designed in such way that they can yield in a nonviolent or controlled manner during longwall retreat, has been used in many longwall mines to prevent tailgate pillar humps. However, this practice often shifts the side abutment load onto the tailgate-face corner especially when a massive and strong sandstone member is present within the caving zone or in the vicinity of the coal seam. Therefore, the abutment pillar design concept has also been used in some hump-prone coal mines to minimize the stress concentration on the tailgate panel rib for the control of tailgate-race corner humps. The disadvantage of using the abutment pillar design concept is that it is more costly and puts additional pressure on mine operations for gate entry development and significantly reduces the recovery of coal reserve. In addition to pillar size, panel layouts. such as the panel width and panel orientation also play a critical role in pillar or face humps and should he taken into account. Based Upon the Cyprus mine design and operational experiences at Willow Creek and case studies at other bump-prone longwall nines in the U.S., the authors attempt to identify the critical factors causing coal mine bumps and to introduce some guidelines and criteria for the design of both yield and abutment pillar systems and panel layouts.

Jan 1, 1999

By M. Zaki Rashad

In this paper, if three slant distances are measured from three given points of known coordinates to an unknown point, the position of this point (X, Y, and Z coordinates) can be determined. A computer program was designed for observing the movement of a point in the roof in Abu-Tartour mine (western desert, Egypt) to measure the convergence. This method, for general using, is very fast and can be applied without any restrictions.

Jan 1, 1990

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By R. J. Morrell

The Bureau of Mines developed a ground support system for use with an underground coal auger. The system consists of inflatable airbags that are inserted in the holes as they are drilled, and then gradually deflated to provide controlled roof caving. This paper presents results of laboratory and field tests of the system that show it to be technically feasible.

Jan 1, 1988

By Alan A. Campoli

Fosroc continues as a leader in the development of cementitious technology for the mining industry. The considerable expertise accumulated in the development of the Fm cement line has been employed in the development of two pumpable, supplemental roof support systems. The Tekprop system is a unique combination of steel and concrete, specifically designed as a viable alternative to conventional wooden supplementd support. The second system is the Fosroc mineable mi which is a cost competitive variable yield system designed to support longwall ventilation and predriven recovery room entries. Two, separate, ongoing, full scale applications of these systems will be discussed during the inference presentation

Jan 1, 1997

By Stephen C. Tadolini

Cable supports offer several advantages over traditional secondary support methods. Cable supports enhance stress redistribution to pillars and gob areas, minimize or eliminate timbers and cribs which reduce ventilation capabilities, eradicate material handling injuries related to the placement of crib supports, and provide a cost-effective alternative to secondary support. The U.S. Bureau of Mines has designed and installed cable supports to improve the stability of tailgate entries in an underground western coal mine. Two entries closest to the Iongwall panel were solely supported with high-strength cables installed with cement grout. Basically, with modifications in the intersections, 360 ft of roadway nearest the longwall panel was supported with two rows of 22-ft-long cables installed on a 7-ft spacing. Approximately 250 ft of a second bleeder entry was supported with two rows of 16-ft¬long cables installed on a 7-ft spacing. Individual cable loads were monitored with hydraulic U-cells and pressure pads. The roof behavior was simultaneously monitored with differential magnetic sag stations and closure meters on 25-ft spacing during longwall panel retreat to evaluate the response of the immediate and main roofs. Cable supported gateroads appear to be a viable alternative in secondary support when compared to wood timbers and cribs. This paper describes the theory, application, and advantages of cable supports and presents the results of the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1993

By Francis S. Kendorski

Underground stone mines tier construction aggregates and industrial minerals are being planned in increasing numbers throughout the United States. At the middle of the last century (1950s) underground stone mines were much more common, and characteristically had no thorough site characterization other than proving reserves and trial-and-error planning. Ground control employed was minimal. Consequently, there was a tendency to conduct minimal pre-mining studies. However, the deposits that lend themselves to little site characterization and minimal ground control are few today, with the best being mined out. Failures of a number of underground stone or similar mines from that era are more common than realized, Underground stone mines almost always use some combinations of square or rectangular pillars, sized to support the overburden load, and spaced to allow the use of larger, more-efficient equipment. Heights are controlled by the available stone quality, interbeds of waste, or technological or safety considerations. Prior to committing to a specific mine plan with subsequent significant capital investment, and prior to having available the wealth of knowledge and experience gained once mining underground, a safe and workable mine layout must he achieved. Early attention to the several different rock units involved (roof, mine level. floor) and their strength as a rock mass with the inherent discontinuities, will allow first approximations of acceptable mine geometries and sequencing.

Jan 1, 2000

By Roy H. Grau

The trend in underground room-and-pillar cod mining is to employ remote-control continuous mining machines to take extended cuts of 40 A or more. Roof fall safety hazards to the mine worker associated with 4ed cutting are not completely de6ned but are known to include removal of the miner operator from the protective canopy, non-compliance with approved cutting depth and CM operator positioning. This report summarizes ground control research performed by the National Institute for Occupational Safety and Health (?-JIOSH) researchers at the Pittsburgh Research Laboratory concerning extended cuts. A combination of statistical analysis and underground investigations have been conducted. Statistical analysis of extended cut use, along with roof fall accidents and fatalities data delineate the extent of the problem in U.S. coal mines. Additionally, an underground study is described where the long-term roof stability of extended cut areas are compared to standard cuts.

Jan 1, 1997

By James Pile

Since C.C. White introduced coalmine roof trusses in 1967. many different systems have evolved. Beginning in the mid 1990's, several types of bar/cable truss systems have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, this new truss increases operator safely. In order to fully benefit from the new truss system, a closer look at the individual components and their interaction was undertaken to understand critical implications on preload and overall support capabilities.

Jan 1, 2004

By Winton J. Gale

The subsidence over a longwall panel at Tahmoor Mine in the Southern Coalfield of NSW, Australia, was found to be approximately twice the size it had been in previous measurements. An investigation into the potential causes was conducted using computer modeling together with hydrological characterization and detailed geotechnical characterization of the strata. The abnormal subsidence was found to be consistent with localized weathering of joint and bedding planes above a depressed water table adjacent to an incised gorge. The study showed that other factors such as variation in stress field, joint zones, variation in rock strength and topographic factors did have sufficient impact to induce the abnormal subsidence. The results have significant implications to subsidence prediction in areas that may be prone to the phenomenon found at Tahmoor. Key indicators of the potential for this form of abnormal subsidence are presented.

Jan 1, 2011

By Brian E. Travis

The recent development of polymer grids for the underground coal mining industry has created new alternatives for supplemental ground control practices. The grids utilize strong, lightweight polymers - usually special grades of polypropylene. High tensile strengths and resulting load support characteristics are achieved by molecular orientation of these polymers in the manufacturing process. One of the most important applications of polymer grids as supplemental ground control is in longwall shield recovery. When shields are moved from one face to another, the determining factor in the success of the recovery is the ground control provided by roof support structures along the old face. Whereas primary support is usually provided by roof bolts and cables which run the full width of the panel, supplemental support is often provided by metallic meshes of welded wire or chain-link fence. lightweight, high-strength polymer grids replace these heavy, cumbersome metallic meshes, giving the operation increased productivity by decreasing installation time and reducing injury downtime.

Jan 1, 1990

By Thomas M. Barczak

Wood cribs have been the dominant form of supplemental support in coal mining for many years. Recently, there has been a renewed interest in prop supports as a replacement for wood cribbing due to the increasing cost of mine timber and engineering advancements in prop design to improve their stability and yield capability. Prop supports generally consume less material, can be installed in less time with less labor, and provide less restriction to mine ventilation than wood crib supports. Several prop supports are now available or under development'. These include: (1) Strata Products Propsetter? Support System; (2) Heintzmann ACS and Super Prop; (3) MBK-Hydraulik MEGA prop; (4) Advanced Mining Technology Inc. (AMTI) BTS Mortar prop; (5) Dywidag Coal Post; (6) Western Support Systems YIPPI support; and (7) "The Can" support by Burrell Mining Products. A comparison of the performance and cost of these support systems to wood cribs is made to provide mine operators with information needed to assess their application potential. Examples of current underground installations are discussed. Included in this assessment are full scale tests of these supports conducted in the U.S. Bureau of Mines' Mine Roof Simulator.

Jan 1, 1995

By George S. Kalamaras

Coal strata strength is included as a vague term in most of the pillar design formulas, either as a questionable fraction of the intact coal strength or a size-dependent relationship for scaling down a laboratory value to the in situ strength. In order to introduce a coal mass strength criterion which would be compatible with current design trends, the Rock Mass Rating (RMR) system was revised to incorporate factors governing coal seam behavior under load. A number of adjustment factors have been proposed but, the most significant change, is the introduction of a parameter representing the heterogeneity of the seam. When developing a rock mass strength criterion, it is necessary to find the constants of appropriate intact rock strength criteria and to establish a correlation to scale down these constants as a function of the RMR. For four intact rock strength criteria, the constants for coal were found using the Nelder-Mead method. To correlate the constants of the strength criteria with the coal seam quality values (RMR), a procedure was developed based on finite element modeling of in situ large scale tests for which the RMR was known. A new coal strata strength criterion is proposed, in a principal stress formulation, for modeling coal pillar behavior when the stress field in a pillar is known. A linear relationship is also given, to be used when empirical pillar strength formulas are used to design pillars. The proposed criteria have been evaluated in a case study.

Jan 1, 1993

By John K. Wood

The development of an expanded cement product represents a major advance in the technology of roof control systems. Such a product is gaining recognition as a valuable tool in today's cost- conscious coal mines. The National Coal Board's Bretby Research Lab, in conjunction with Polement Ltd., developed the first lightweight cement for use in the mines of the United Kingdom. The product, Aqualight, is a low-density (about 12.5 PCF) cement with a typical compressive strength of about 19 p.s.i. The final product increases in volume by approximately 15 times its dry powder volume. Aqualight gels in about 2 minutes, becomes self-supporting in 15 minutes, and fully cur& in 24 hours. When subjected to a load, the "cells" within its bubble structure collapse so that the product gains in density and compressive strength while retaining its integrity. Traditional methods to contain and support roof fall cavities through cribbing and blocking are both dangerous and labor-intensive. Aqualight represents a significant advantage over such traditional methods. It is non-toxic, non-cmbustible, and very easy to install. Aqualight can be pumped to the worksite from re- mote locations (as much as 600 feet), thereby reducing danger to men and equipment. Addition- ally, the strength of the cured product can be varied by adjusting the expansion ratio and resulting density. A compressive strength of 150 p.s.i. can be obtained in this manner. Although primarily designed to fill cavities resulting from roof falls. Aqualight has found a wide range of applications in mining industries around the world. In addition to cavity- filling, Aqualight has been used for ventilation stoppings, fire stoppings and emergency fire control, backfilling between arches and the roof and ribs, and backfilling of old workings. Since its recent introduction into the United States. Aqualight has been used by MICON SER- VICES, INC. to fill several roof fall cavities along headgate entries. In all cases, the cavities were contained and the longwall moved through without problems. Roof Pall cavities along main haulage entries and at shaft/slope bottoms have been successfully filled. MICON has also installed Aqualight as backfill material around arches. A current major project is the installation of trial ventilation seals using Aqualight as an alternative to traditional block and mortar construction. Pending MSHA approval, MICON anticipates the use of Aqualight in the construction of both ventilation seals and stoppings. In addition to new construction, Aqualight can be employed to repair stoppings damaged by roof convergence and floor heave. In labor savings alone, this is very attractive for remote stopping repair. Among the many other uses of Aqualight is the backfilling of old auger holes, which will support the highwall and allow access to coal re- serves which are presently sterilized.

Jan 1, 1986

By Jaco J. van Vuuren

Modikwa Platinum Mine, in the Eastern Bushveld of South Africa's Limpopo Province, is a new operation employing a hybrid mining method where mechanised methods are used for the main developments and the narrow, 60cm reef is conventionally stoped using a down-dip conventional mining method. Throughout the mine, the hanging wall immediately above the reef comprises 3 jointed and laminated layers of varying thickness, commonly known as the triplets, below a non-cohesive leuconorite parting plane. At North shaft, using pre-stressed standing support and mechanically anchored rockbolts, it was found difficult and hazardous to hold all three triplets in the hanging wall, however bringing them down caused a significant increase in dilution and therefore cost of mining. A novel solution was conceived whereby two of the triplets are kept up using short, stiff resin anchored rockbolts installed systematically within 0.5 m of the face. This resulted in both safety and productivity benefits. The rockbolts create a stable and safe hanging wall and allow the mine to extract UG2 reef more economically. New drilling equipment, developed locally from available drilling technology, can be operated from a safe position, and in situ tests and measurements are made to confirm effective support. The technology and underlying concepts were successfully tested in a trial stope prior to rolling out the new support system across all the stopes at North Shaft. This has involved an extensive training programme to ensure that the rockbolt system is installed correctly and that the conditions are appropriate for this technology. The paper describes the motivation behind the project, the underlying technology and its application to Modikwa, and the benefits now being realised.

Jan 1, 2004

By Kenny D. Basnett

An analysis of the Roof Falls Data Base (RFDB) for underground coal mines in Illinois for the period 2004?2008 indicated that about 80% of the roof falls occur at intersections and are associated with geologic anomalies or a rapidly changing geologic environment. Most falls are associated with anomalies such as clay dikes, differential compaction faults, shear zones, joints and fractures, and geologic structure. Therefore, a better analysis of the geology with emphasis on mapping anomalies such as joints and fractures and their application is necessary to improve ground conditions and safety. Such studies within Illinois Coal Basin are limited. This paper presents a mapping study of the joint orientations with documentation of dip of the several lithological units that lie directly above the Herrin No. 6 Coal seam around southern Illinois. These units include the Energy Shale, Anna Shale, and Brereton Limestone. The mapping was done in three mines and the data were plotted on a stereographic projection to determine the average characteristics of joint planes. The study mines included two deep underground mines and one shallow highwall mine. This study has helped identify favorable mining and support orientations in areas of highly variable geology. These are currently under review by the cooperating coal company for experimental roof control studies.

Jan 1, 2011

By Christopher Mark

Mines with exceptionally low-strength roof (UCS <3,500 psi and CMRR <40) are much more likely to struggle with roof falls than other mines. Weak-roof is a particular problem for many room and pillar mines in the Midwestern and Northern Appalachian coal basins. Traditional roof support techniques are often not up to the challenge at these operations. This paper focuses on two mines, one operating in the Upper Freeport seam and the other in the Herrin No. 6 seam. Together, the two mines had more than 300 roof falls during a recent 5 year period. Each has experimented with a variety of roof bolt types and lengths, and with different supplemental supports. Detailed statistical analysis was conducted to determine which support combinations have proven to be most effective. Geology, horizontal stress, and time are also important at both mines. Successful control techniques have included; ? Identifying particularly troublesome lithologic roof units; ? Installing longer and stronger roof bolts; ? Installing supplemental support in intersections, and; ? Limiting the duration that a panel remains open. The lessons learned from these mines, and others like them, could help improve ground control safety for the entire U.S. mining industry.

Jan 1, 2004

By M. Guana

Island Creek Corporation is predominately an underground mine operator deploying room-and-pillar and retreat longwall mining methods for extracting coal. Wide variations are encountered in overburden depth, stratigraphy, and insitu stress fields. This requires major adjustments in mine design among mines and occasionally within a mine. Simple rock mechanics principles are utilized in mine design to optimize safety and productivity. Physical observations and micro deformation monitoring of roadways are the primary techniques employed. Pillars and artificial support systems are the primary design elements modified. The specific case histories reviewed in this paper include narrow panels with high extraction for conventionally mined rooms, pillar sizing for longwall gate entries at great depths, and bolt type selection for difficult ground conditions.

Jan 1, 1988

By H. N. Maleki

Tension-torque relationships were investigated *n a coal mine for bath standard 5/8 in. (16 mm) bolts and a vibrating wire instrumented bolt, using conventional and controlled installation techniques. The instrumented bolts differed from the standard bolts by their head size and hole preparation procedures. The controlled installation technique developed by the U. S. Bureau of Nines (USBN) involved using hardened washers and lubrication in the bolt assembly, and maintaining a minimum thrust level during bolt installations. The object of this study was to determine the tension to torque ratio (lb/ft-lbs; for standard bolts and instrumented bolts for both conventional and controlled installation techniques, and to modify the bolt assembly so that the ratios would be equal for the instrumented and standard bolts for both installation techniques. It was shown that the instrumented bolts installed in faced holes had a similar tension torque ratio td that of standard 5/8 in. (16 mm) bolts installed in unfaced holes for each installation technique, and thus they were representative of other uninstrumentea bolts. This was achieved by evaluating the influence of several factors oh the relationship, including: facing the hale surface, introducing washers and lubrication in the bolt assembly, and applying different levels of thrust at installation due to bolter operator practice. The tension to torque ratio fur conventional bolts was only 21 (lb/ft-lb) for the coal mine, resulting in an installation tension of 4000 lbs (17.8 kg) with the typical installation torque of 150 to 400 ft-lb. This tension level was approximately 50 percent of the required bolt tension, and thus, it was concluded that torque standards are not sufficient to assure adequate bolt tension. .he low tension levels were due to the particular wait hardware in use, operator practice, and bolt fencing.

Jan 1, 1984

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994