Search Documents

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham. Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By Hui Chen

The paper describes the use of a physical model technique to investigate the failure modes of mine tunnels with reference to the in situ stress field. The characteristics of stratification commonly encountered within UK coal mining conditions have been taken into consideration. The investigation has indicated that the weak floor strata in coal mining tunnels, under the action of high rock stresses, will be subject to the floor lift problem in both predominantly horizontal and vertical stress fields. However, the failure mode and mechanism varies between the two stress field patterns. In the predominantly horizontal stress field, the tunnel floor tends to fail by gradual bending of the laminations, whilst in the predominantly vertical stress field, the floor tends to fail by a shearing action with the failed material lifting in the form of a block. The failure mechanism is discussed with reference to mechanics theory.

Jan 1, 1993

By S. S. Peng

In recent years many roof falls have been conveniently attributed to the adverse existence of a high horizontal stress. The normal practice of not conducting a follow-up study in a roof fall investigation usually leads to a wrong conclusion. This paper describes two cases of massive oriented roof falls in two separate room and pillar mines. The investigation in each case involved the analysis of past history and current conditions from which remedial measures were recommended and implemented. A follow-up period of up to three years was performed to evaluate the effectiveness of the recommended remedial measures. In both cases, high horizontal stress was proven positively not the cause, contrary to the original conviction of mine management Rather, a weak immediate roof was the basic cause Under a weak immediate roof, a proper roof bolting plan and adequate entry width and intersection span must be strictly observed.

Jan 1, 1999

By Richard J. Perin

Subsidence monitoring was conducted in proximity to the 1-A and 2-A longwall panels at Consol Pennsylvania Coal Co.'s (CPCC) Bailey Mine slurry impoundment. Monitoring fullfills federal Mine Safety and Health Administration (MSHA) mandated requirements. Construction of the monitoring network was completed between May and June, 1986. Monitoring was conducted before, during, and after mining of the panels between June, 1986 and February, 1987. The embankment was not deleteriously impacted by longwall mining.

Jan 1, 1988

By Yi Luo

The severity of disturbances caused by longwall mining subsidence to various residential structures can be re¬duced. The success of such mitigation efforts depends on accurate subsidence prediction, correct assessments of the subsidence influences, and careful design and implementa¬tion of the proper mitigation measures. This paper presents the systematic approach involved in the subsidence mitiga¬tion efforts with a case demonstration.

Jan 1, 2003

By K. Haramy

Coal mine bursts or bumps involve the violent, rapid failure of coal and rock in or around a mine excavation. Failure is normally associated with high stress and brittle or brittle-elastic materials; in coal mining, bursting may also be associated with desorbing gas, and this type of failure is termed an outburst. This paper discusses factors affecting coal mine bursts and several methods to predict bursts, including microgravity, microseismic, rheological, rebound, and drilling-yield methods. Methods to avoid burst conditions using volley firing, hydraulic fracturing, and auger drilling are also discussed. A case study is presented in which the redistribution of stresses and displacements was found to be associated with a burst at a deep longwall coal mine. The research showed that stresses are redistributed following the burst.

Jan 1, 1984

By Jinsheng Chen

Longwall mining-induced abutment loads on the surrounding coal pillars can be grouped into two categories in terms of the relative position of the coal pillars and the longwall face. They are the front and side abutment loads. Even though a lot of research and efforts have been made to study the nature and behavior of these longwall mining-induced abutment loads, their influence zones and magnitude are still not well defined and fully understood due to the complexity of geological conditions and the longwall muting-induced overburden strata movement. The uncertainty about the mining-induced abutment loads often forces consultants and mining engineers to employ a conservative approach in designing coal pillars and entry roof control plans. The problems with this approach are that: (a) it increases CM development¬longwall retreat footage ratio, (b) it decreases coal recovery, and (c) it increases !Ill' operating costs. However, a more liberal approach may create safety issues and result in loss of production. Therefore, the importance of accurately defining the influence zones and magnitude of the front and side abutment loads induced by longwall mining can never be over emphasized. The authors in this paper attempt to define the influence zones and discuss the magnitude of the longwall mining-induced abutment loads by analyzing the field data measured at RAG American Coal Company's longwall mines. In addition, the relationship between entry stability and the balance among roof/floor conditions, pillar design, and roof control plan is also briefly discussed.

Jan 1, 2002

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

By Thomas M. Barczak

Roof support systems are necessary to provide stable mine openings and much research has been conducted to design a variety of roof support systems that will function in various manners to ensure that stable ground conditions are achieved. Despite these advancements in technology, mistakes continue to be made in the evaluation and/or installation that significantly degrade the support capability or lead to erroneous determinations of support expectations. The purpose of this paper is to discuss misconceptions about how roof supports perform and factors that impact their performance. The goal is to present practical information that will assist mine operators and engineers in selecting, installing, and evaluating roof support systems properly, and help them to avoid mistakes that can lead to erroneous expectations and potentially catastrophic results that may lead to roof falls. The paper is limited to a discussion of secondary roof support systems and powered roof supports such as longwall shields.

Jan 1, 2001

By Yunqing Zhang

Weak shales refer to those with lower strength, thinly- laminated structure, sensitivity to moisture and weathering as well as significant time dependent behavior. It has been said that many future coal reserves with good quality have weak immediate roofs. Therefore their geo-mechanical properties and behavior must be known before an appropriate support plan can be designed. In this study, four types of shales collected from underground coal mines were tested in the laboratory. Their modes of failures in underground were observed and correlated with their lab behavior. The failure mechanisms of thinly-laminated weak shales were analyzed by the means of numerical modeling.

Jan 1, 2004

In recent years, improvements made to the longwall system have accelerated at a faster pace than those made to the gate entry development system. As a consequence, unless planned years ahead of time, extending the panel length is nearly impossible without some innovative approach. At Cyprus Amax Coal's Emerald mine the G panel length was extended by 3,500 ft- by developing three entries across it to facilitate development of its headgate and tailgate entries simultaneously when the adjoining F panel was in operation. After evaluating alternative supporting methods and associated risks, determination was made to backfill these entries and crosscuts using a low strength flyash cement mixture prior to mining thru. Instrumentation was also used to monitor the stress change or front abutment stress in both the coal and the backfilled material ahead of the face. Longwall mining thru these three entries took about four eight-hour shifts and proved to be very successful. The designed flyash cement mixture provided adequate roof stability and caused no difficulty in the shearer's cutting while eliminating an in-panel longwall face move and minimizing the risk of roof or floor failure in the in-panel openings, or in the worst scenario loss of the face during the longwall cutting thru. This approach provided the intended result of extending G panel and recovered about one million tons of coal. This paper summarizes the engineering design of the cutting-thru project and flyash cement mixture, front abutment stress changes within the longwall coal block, backfilled material, and coal pillars ahead of the longwall face, and our underground observations

Jan 1, 1997

By Robert Trueman

This paper details the results of an assessment aimed at understanding the shield loading mechanisms associated with strata-related issues on a longwall face. Shield load cycle analysis theories developed by the authors were used to quantify the interaction between the shields and strata. Shield pressure data was back-analyzed using a version of the Longwall Visual Analysis (LVA) software that has been extended to enable efficient load cycle analysis to be undertaken. The software outputs enabled the shield strata interactions to be characterized. The results of the analyses indicated that the major cause of the roof falls was high-level periodic weighting, resulting in periodic shield overload. Exploration borehole data was analysed to identify and characterize the overburden unit that was the likely cause of the shield overloading.

Jan 1, 2011

By C. Thomas Blevins

This paper is intended to be a hands on experience account about ground control in a Southern Illinois coal mine. Its aim is to show how a combination of real world mining practices and constraints along with practical engineering theory mesh together to formulate a ground control program in adverse conditions. These conditions - your typical localized slips, splits, rolls, clay intrusions, water, changing types and thicknesses of materials, etc. - being amplified by a very strong horizontal stress field. A review will be made about the formation of the overall ground control plan and to what degree it has been successful. A presentation of the various roof control systems and their component parts, how these systems were developed, and the theory behind them will be made. The pointing out of some of the flaws that we found in the components, installations, and/or theory will be part of this presentation. A brief look at some of the efforts in the following items will be made: quality control of the roof control products; using the computer to help keep track of roof control information and soliciting help from various universities, governmental agencies and consultants to give different perspectives to the problem.

Jan 1, 1984

By Winton Gale

"The aim of this paper is to summarise the results and conclusions of Australian Coal Association Research Project (ACARP) Report Cl3013 which relate to water inflows into a mine which occur through the overburden above and adjacent to longwall panels. The study assessed available data of inflows into underground coal mines and utilised computer simulation of water flow through fracture networks. The study concluded that flow into mines is typically via an interconnected network of pre-existing and mining induced fractures. The height above the coal seam that mining induced fractures extend is typically related to the width of the panel. However the potential for those fractures to form a connected network which can facilitate flow, is related to the amount of subsidence and the depth of mining. The study compares model simulations with measured data and provides guidelines to estimate the average hydraulic conductivity of the overburden above extracted longwall panels in Australia.INTRODUCTIONWater inflow into coal mines has been a design issue for many years. Guidelines as to the potential for water inflow have been developed in many countries based on local experience and the form of mining being undertaken. In most instances, the guidelines relate to inflows which would endanger underground personnel and operations.In more recent times, water inflow criteria for mines has been widened to include lesser inflows which may not impact on mine safety or operations, but have the potential to reduce water flow within streams and surface aquifers. For the purpose of this paper the larger inflows which are readily measured in a mine or may impact on mining safety are defined as mine inflow and the lesser inflow relating to aquifer water loss as environmental inflow.The water losses referred to are those which enter the mine from the surface or from near surface aquifers.The empirical relationships developed as mine design guidelines or regulations typically relate to high flow (mine inflow) situations and in this paper, these have been reviewed as to their application to environmental inflow. In many cases environmental inflows were unlikely to have been noted or recorded in many mining operations in the past."

Jan 1, 2010

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017

By Samrat Mohanty

The construction of underground hydrocarbon storage caverns in Jurong Island, Singapore, is nearing completion. The facility, located beneath the seabed of Banyan Basin, is comprised of five storage caverns with a storage capacity of approximately 1.5 million cubic meters. The galleries of each cavern are 20 m wide by 27 m high and approximately 340 m long. In addition to the storage caverns, various access and operations tunnels are required to support the facility. Among these are water curtain galleries to ensure that hydrostatic pressures in excess of hydrocarbon storage pressure are maintained in the rock mass surrounding the storage caverns. Early in the design process, conventional steel rock bolts with resin polymer grout were considered for ground control. However, the construction contractor proposed using fibe-reinforced polymer (FRP) bolts with cement grout due to the corrosive hydrologic environment, weight and handling considerations, local construction preferences, and the requirement to have a cavern design life of 50 years. FRP bolts with cement grout were ultimately chosen for the project. The FRP bolting system has proven to be very successful, with no ground failures experienced where systematic FRP bolting has been applied. This paper discusses the properties of FRP bolt/cement grout bolting systems, their characteristics in relation to steel bolt/resin bolting systems, and numerical modeling results assessing their performance.

Jan 1, 2014

By Yang Li

For the study of overburden movement in longwall mining of shallow coal seams, most scholars merely consider the thickness of bedrock and top soils. In this paper, the overburden movement in longwall mining of shallow coal seams with thin top soils and key strata group was studied. By using numerical simulation, the development of fractures in the overburden was analyzed for different ratios of panel width to depth (W/D) and depth to mining height. The results show that the overburden movement changed with the variation of mining height, panel width and depth under the specific geological conditions. It also explain how different overburden disturbance structures, such as ?three zones? (caved, fractured, and continuous deformation zones), ?two zones?(caved and fractured zones) or ?steps-like collapse? are formed under different mining conditions. The results broaden the vision for research on overburden movement in longwall mining of shallow coal seams.

Jan 1, 2014

By Kristine L. Pankow, Keith D. Koper, Michael K. McCarter, Jared R. Stein

"The Wasatch Plateau region of central Utah contains a number of active underground coal mines in an area of well-documented natural seismicity. As a result, there are several hundred seismic events recorded in this region every year that may or may not be attributed directly to mining activity. Previous studies have linked the majority of this seismicity to mining activity through various means, but have not attempted to develop a method for categorizing individual events within a seismicity catalog. This study uses both relative relocation and waveform cross-correlation to separate events based on hypocentral depth and waveform similarity, respectively, in the area surrounding a single longwall coal mine within the Wasatch Plateau. We conclude that relative relocation can help with depth discrimination, but there are some unavoidable limitations caused by sparse seismic network coverage. The cross-correlation technique is more promising, with the ability to group events by waveform similarity and track mining progress over both space and time. With cross-correlation based clustering, we confirm that the vast majority (97.6%) of events in the study area are directly related to mining activity, but that a small population of natural seismicity is present as well. Eliminating this natural seismicity from the catalog of seismic events, leaving only those events related to mining, can give operators valuable information about the changing conditions as mining progresses and eliminate concern over events unrelated to mining activity.INTRODUCTIONA number of underground coal mines are located in the Wasatch Plateau region of central Utah, and have been in operation since the late 1800s. This activity has resulted in a well-known history of mining induced seismicity (MIS) (Wong, 1985). Additionally, this area is situated near the border of the Basin and Range and Colorado Plateau physiographic provinces, where naturally occurring tectonic earthquakes also occur (Arabasz et al, 1980). Seismicity separating these physiographic provinces is part of a larger band of seismic activity known as the Intermountain Seismic Belt (ISB) that runs from Montana to Arizona and cuts through the western boundary of the central Utah coalfields (Smith and Arabasz, 1991) (Figure 1)."

Jan 1, 2015

By Morgan M. Sears, Gamal Rashed, Jim Winfield, Brent Slaker

"Over the past decade, ground falls have resulted in five fatalities, representing over 40% of all fatalities occurring in underground stone mines in the United States. In conjunction with recent high-profile pillar collapses, the need for further ground control research in the nation’s stone mines is evident. Ground conditions are growing more difficult. Therefore, this research is focused on deep cover, steeply dipping, and multi-level underground nonmetal mines. The objective of this paper is to introduce a geomechanical study of pillar development in a steeply dipping limestone deposit. To accomplish this, a numerical model was developed using input from modified laboratory test data and in situ stress measurements provided by the mine to simulate the development of a pillar under these conditions. The model was then verified against field observations and stress mapping. The calibrated model was then used to calculate the estimated stresses in the pillar and immediate roof as development progresses around an instrumented pillar.INTRODUCTIONGround falls represent a significant hazard in the nation’s underground stone mines. In response to recent large-scale pillar collapses, as well as stakeholder interactions, researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at mines operating in challenging operational environments. These include deep-cover, steeply dipping, and multi-level mines where there is the potential for an increased risk of ground failure. The Pleasant Gap Mine, shown in Figure 1, operates in the Valentine Formation, which is typically light grey, extremely fine-grained limestone, and approximately 21.3 m (70 ft.) thick. The Centre Hall Formation makes up the immediate and main roof members and is approximately 9.1 m (30 ft.) thick, consisting of medium-dark-gray limestone (Murphy et al., 2018). Situated in a syncline, the top of the Valentine Formation dips at approximately 19° with a strike of approximately N54E in the area of interest (see Figure 2)."

Jan 1, 2018

By Joao Felipe Costa, Jair C. Koppe, Andre Zingano, Cleber Gomes

"Run-of-mine Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. A large amount of waste results from the coal preparation, and it must be disposed of in waste piles or waste dams, depending on the material size. These waste disposals are the cause of serious environmental problems, not only in the short and medium terms, but mainly in the long term, due to the risk of provoking acid drainage or spontaneous combustion. Waste disposal requirements also demand large areas. Other problems include the pillar and roof stability in abandoned and mined out areas, building of edifices on the old and active mines, and mining under urban areas. To solve these problems simultaneously, backfilling the entries in mined out areas began with two objectives: to understand the mechanical behavior of the filling material and to model the backfilling of room-and-pillar coal mine entries through numerical simulation. Laboratory tests were performed for different filling material (with and without cement) to determine its mechanical properties and failure criteria. Based on this study, it was possible to conclude that the backfill method is a good strategy to improve the ground stability in room-and-pillar coal mines for the long term, especially for weak coal seams, and to reduce the quantity of material on waste piles on the surface.INTRODUCTIONRun-of-mine (ROM) Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. Two types of waste are associated with power plants that bum coal for energy generation: 1) the waste from the coal preparation plant and 2) the ash from the power plant after coal burning.The Brazilian coal ash content in the ROM coal is between 45 and 55%. The clean coal is 20 to 30% ash for 4,500 kcal/kg (18,000 BTU). The coal preparation plant recovery is only about 35%. Santa Catarina State (SC) produces about 7 million tons/year of ROM coal, which results in a total of 4.5 million tons of waste. This is a large amount of waste that must be disposed of in waste piles or waste dams, depending on the material size. The waste and ash content is represented by silicate materials, such as clay and sand, and by sulfide materials, like pyrite and organic sulfur (between 1and5%)."

Jan 1, 2010