Search Documents

By Scott Donald, Barry Esford

Cameco Corp. operates uranium mills and tailings management facilities at its Key Lake and Rabbit Lake operations in Northern Saskatchewan, Canada. Development at both mine sites began in the 1970s, with initial tailings deposition occurring within above-ground impoundments, which was common for these facilities at the time. As open pits became available at each site, and mining continued at other orebodies in the area, tailings management shifted to in-pit facilities to meet stakeholder expectations and improve the long-term security and environmental performance of tailings management at these facilities. The in-pit facility at Rabbit Lake (receiving tailings since 1984; Fig. 1), was one of the first (if not the first) engineered in-pit tailings facilities in the world and adopted a full pervious surround design concept with subaerial deposition. Under this concept, permeable sand and coarse rock are placed at the base of the pit, around its perimeter, as well as overlying the tailings at closure to promote regional groundwater flow bypassing the lower-permeability tailings. In contrast, at Key Lake, the in-pit facility (receiving tailings since 1996) adopted a partial pervious surround design concept. Under this concept, permeable materials were again placed at the base of the pit, and partway up the side walls; although for the upper portion of the tailings, the material is placed directly against the natural geologic materials. In the Key Lake case, the natural geologic environment provided the required bypassing of the tailings deposit to achieve the desired environmental performance while the base drain again facilitated pumping during operations to achieve consolidation objectives (Fig. 2). In both the initial design of the facilities, and through more than several decades of operation, it is clear that although in-pit tailings facilities provide common benefits with respect to long-term geotechnical stability, it is critical that their design approach take into consideration site-specific conditions

Jul 1, 2025

By Philip G. Meikle

The Bureau of Mines Coal Mining Technology program has developed new concepts aimed at improving the efficiency of underground coal product ion. Conceptual designs have resulted in equipment prototypes, some of which are currently undergoing proof-of-concept evaluations at Bureau and cooperator facilities. Several of these systems and concepts are described.

Jan 1, 1984

By Larry Diaz

A single stage ball mill-cyclone circuit was extensively tested for its reactions to step changes in three controllable variables: feed rate, water to cyclones, and water to the ball mill. A series of carefully designed tests are to be carried out in order to determine relationships between the various ball mill and cyclone parameters. Cyclone overflow particle size distribution is to be continuously monitored during the tests using an ultrasonic device. Other circuit variables that are to be measured and recorded are feed rate, ball mill mass flow, cyclone feed and overflow densities, cyclone feed sump level, water flows, etc. Once the circuit performance is defined, two types of grinding circuit control systems will be evaluated: (a) mass flow-based; (b) particle size- based. Results obtained by each approach in terms of feed rate and cyclone overflow size distributions are discussed. The high sensitivity of continuous particle size measurements to grinding circuit disturbances is emphasized.

Jan 1, 1971

By A. D. Davis

A ground-water flow model was developed to simulate the post-mining recharge rate at the Belle Ayr surface coal mine in the Powder River Basin near Gillette, Wyoming. State regulations of Wyoming require that reclaimed lands should provide a rate of recharge that approximates the pre-mining rate. Steady-state calibration and transient simulations showed that the post-mining recharge rate in backfill is at least five centimeters per year, exceeding the original infiltration rate of 0.4 centimeters per year to shallow, overburden aquifers. Major reasons for the increase include the flat topography of reclaimed areas and decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate less than five centimeters per year but somewhat greater than the pre-mining rate.

Jan 1, 1995

By Ellis J. Brien, O&apos

This afternoon I would like to talk to you about coal, its defi- nition, its constituents, its associated minerals and present and future coal preparation techniques. This discussion will be an attempt at presenting sufficient coal preparation and associated fundamentals to enable you to understand "deep cleaning", a more advanced beneficiation process which will be commercially practiced in the near future.

Jan 1, 1976

By R. E. Driscoll

The exploration, geologist of necessity has to have a wide working knowledge of many specialties other than hiw own, First he has to use his own technical background to find a deposit,, of a mineral that is of interest, Once found, his problems are Just beginning, He then has to assume the role of an economist, an accountant, a mining engineer, a chemist, a metallurgist,, a salesman and what-have you, In the economic field, he must determine the marketability of either the ore or the refined mineral. He must gauge the supply and demand for the particular mineral he is interested in and make his best guess as to ultimate cash flow from a deposit over the estimated life of said deposit, He must then assume the role of a mining man and estimate cost of recovery, including an, evaluation of the most economic mining method, cost of supplies and labor, and again estimate a net cash flow. He must then determine amenability of ore to economic metallurgical methods, he must determine the legal status of the property involved and, after analysis of the specific situation, determine the best approach to a deal, After all of this he must sell it to the people who will put up the money and then put his deal together and sell it to the people who own the minerals, if that be necessary. Then he has to sit back, with crossed fingers and crossed legs wondering for some months, and in many cases even years, whether or not he is right. The expenditures required to open up a mine in this day of wild inflation are such that he has to be right, and the responsibilities are awesome.

Jan 1, 1958

By G. P. Hand

Graphite usage in the United States during 1994 was fairly strong. The hearty showing of the domestic economy, along with sound performances from the major industries that use graphite, helped make 1994 a solid year for the graphite industry. Supply Virtually all natural graphite is imported into the United States, as there is no domestic production. The primary producers are Brazil, Canada, China, Madagascar, Mexico, Mozambique, Sri Lanka and Zimbabwe. Mozambique is a new producer. It is now supplying a high-carbon, large-crystallite flake in large quantities. Sri Lanka continues to experience problems with one of its two mines, closing operations in December 1994. The synthetic graphite used domestically was produced primarily in the United States as a byproduct of electrode production. Synthetic graphite was also imported from Switzerland for specialized applications. The purified graphites/carbons, such as Desulco and ThermoPURE materials, were also produced domestically. There was a sufficient supply of all types of graphite to meet domestic demand.

Jan 1, 1995

By Ivan Caetano Machado

Good morning ladies and gentleman. During 1995 Prof. R. P. King (University of Utah Comminution Center) presented 2 papers on new horizons in comminution: "Comminution Research in the United States " was presented at the 1995 Meeting of the National Mining Association, while "Comminution: Meeting the Needs of Fundamental Research in the Mineral Industry" was presented at the 2nd SME Research Forum - 1995. In both papers a very interesting graph named "Energy usage for various comminution schemes" illustrated some poignant issues proposed by Prof. King. We do think that some of Prof. King's ideas might very well serve as "warm-ups" for this Comminution Panel Discussion, which are ultimately the goals to be reached by the 3-minute presentations. Thus, we shall be addressing in the sequence Prof. King's most relevant ideas (as well as introducing his graph), intending therefore show how important creative and state-of-the-art Mill Modeling is, if it is to become a Tool to Effective Cost-Saving Optimization Strategies.

Jan 1, 1996

By M. Cambridge

The extractive industries are currently, and will continue to be, major contributors to the world economy, particularly in the developing world where economic growth is dependent upon a sound supply of primary materials. However, tailings dam and other mine failures have been very much a feature of recent anti-mining publicity, particularly in Europe, and thus instrumental in inhibiting new mine developments. Although, superficially, the record of dangerous incidents might support the anti-mining position, closer inspection suggests otherwise. This paper reviews the failures which have occurred over the last 50 years and demonstrates that, though poor practice is an ongoing problem for the industry, the record is one of improvement in both design and practice. Examples are provided of significant events which have led to dramatic advances in design and operation. The paper assesses the improvements made in technology and practice, and concludes that historic events must continue to form the underlying basis for design and operation of future mining projects.

Jan 1, 2005

By Edward M. Jacobs

In some ore grinding circuits it is desirable to make separations purely on size. The normal choice for this is vibrating screen equipment. Developments in screening process technology have led to improvements in the capacity and efficiency of vibrating screens, through the adoption "Thin Layer Wet Screening". This process can reduce recirculating loads and equipment requirements in the ore grinding circuit.

Jan 1, 1985

By W. E. Horst

In Part I of this paper we describe two techniques that were employed in the development of mathematical descriptions of the size reduction process which takes place in a ball mill. In Part II we show how the comminution model was imbedded in a process model to effect steady-state and dynamic simulation of a closed-circuit grinding operation. Increasing emphasis is being placed on development of approaches whereby the essential characteristics of a process can be succinctly represented in terms of a mathematical description of the relationships that exist among important process variables. This activity, commonly known as mathematical modeling, predates modern electronic computers: however, these computers with their tremendous computational capability have given new impetus to the whole field. Although the computer is quite helpful in the development of mathematical models, the real value to the engineer lies in the fact that computers represent such a powerful tool for simulating systems described by mathematical models. As a consequence, engineers may simulate and thereby study the behavior of complex. interacting, systems over a broad range of process variables and configurations once appropriate process models have been developed for the sequence of steps comprising the process.

Jan 1, 1970

By III Kimball

Mining wastes have received individual attention under the Resource Conservation and Recovery Act (RCRA) since its inception, in recognition of the special characteristics that distinguish mining wastes from other solid wastes. The Environmental Protection Agency (EPA) has recognized that: - Mining wastes are generated in much larger volumes than other industrial wastes. Most material handled in mining is waste (over 99% in many cases) and not marketable product, whereas waste is a small portion of raw materials used in most industries. Consequently, controls used for hazardous wastes may be technically infeasible or economically impractical. - Nearly all mining waste is managed at the site of generation and is land-disposed. . - Mining wastes typically pose lower hazards than other industrial wastes. Mining operations are located predominantly in sparsely populated areas and in arid or semi-arid areas with little surface water runoff and deeper water tables.

Jan 1, 1990

By A. S. Paschoa, A. W. Nóbrega

INTRODUCTION There are now over twenty years since the radiological characteristics of the brazilian regions of Araxá, Tapira and Barreiros, three locations adjacent to each other, in the state of Minas Gerais, Brazil, started being surveyed by investigators from the Instituto de Biofísica da Universidade Federal do Rio de Janeiro (IB/UFRJ), Pontifícia Universidade Católica do Rio de Janeiro (PUC/RJ), and New York University (NYU) (Roser and Cullen, 1958; Cullen et al, 1980). The importance of the Araxá apatite – Ca5,(P04)3(OH, F, Cl) - and pyrochlore - NaCaNB206F - for the production of large quantities of fertilizers and niobium was early recognized (Roser and Cullen, 1958). Interesting data have been gathered and published throughout the years on the contents of naturally occurring radionuclides in geologic materials, soils, grass, foods and waters of the Araxá region (Eisenbud, et al., 1964; Penna Franca, et al., 1965a, b; Roser et al., 1966; Penna Franca et al., 1970; Cullen, 1977; Penna Franca, 1977; Cullen and Paschoa, 1978; and Cullen et al., 1980). The radioactivity of the Araxá region is associated with mineral deposits of niobium rich pyrochlore and phosphate rich apatite. There are in this region mineral ores with 3 to 5% pyrochlore with 2 to 2.5% Th as Th02 and 50 to 150 ppm U308 in the matrix, while the apatite deposits contain up to 150 ppm U308 and a thorium concentration similar to that of the pyrochlore deposits (Paschoa and Palacios, 1981). As an indication of the high thorium content of the Araxá soils the 228Ra and 224Ra activity concentrations were reported to range from 10.6±0.2 to 62.4±0.7 pCi228Ra/g soil in 7 samples and 2.1±0.1 to 104±1 pCi224Ra/g soil in 19 samples (Cullen, et al., 1966). The uptake of radium isotopes by edible roots vegatables and fruits growing in the soils of the Araxá region can be illustrated by the data listed in Table I. The biological availability of natural radium isotopes in some segments of the Araxá soil allows a large variation in the 228Ra, 224Ra and 226Ra concentrations in vegetables and edible roots, as can be seen in Table I. This fact makes quite difficult a quantitative local assessment of the radiological implications of mining the Araxá mineral deposits of pyrochlore and apatite for production of niobium and phosphate fertilizers, respectively; since one cannot easily separate the naturally occurring from the technogically enhanced radionuclide contents of foods. The position of the city of Araxá inside the contour of the state of Minas Gerais appears in the upper part of Figure 1, which shows the outlined map of Brazil with the positions of the cities Brasilia and Rio de Janeiro also indicated. The lower part of Figure 1 is a representation of the Araxá region in an expanded scale, which indicates the locations of the pyrochlore and apatite deposits in relation to the city of Araxá, as well as the nearby hydrographic basins. The distance between the city of Araxá and the pyrochlore deposit is about 8 km, and between the pyrochlore and apatite deposits is 4 km. This paper deals tentatively with the radiological implications of the industrial operations taking place in the Araxá region for the exploration of the pyrochlore and apatite deposits. However, one must bear in mind, firstly, that the radiological implications of these industrial activities are by far too complex to be covered adequately by the limited amount of data to be presented in this paper, and secondly, that such implications cannot be considered of local character only. INDUSTRIAL OPERATIONS The commercial exploration of the Araxá deposits of pyrochlore and apatite started only few years ago, motivated by the increasing demand of niobium and phosphate fertilizers in Brazil and the world. As a consequence of the industrial operations in Araxá, a redistribution of the uranium, thorium, and radium originally present in the local deposits of pyrochlore and apatite started occurring in the seventies, with possible radiological implications for the Araxá region and its immediate surroundings, not to mention the destinations of the end products of such industrial operations. A literature review on the radioactivity associated with the extration industries of selected minerals was made by the USEPA (Bliss, 1978). The low level radioactive wastes of the industries for copper ore mining and rare metals processing have been object of particular attention (Fitzgerald, Jr., 1976; Eng, et al., 1979), but the short and long term implications of the radioactivity associated with the niobium industry were also subjects of concern (Knight and Makepeace, 1978). Recently, high 232Th and 226Ra concentrations in samples from the tin mining industry in West Malaysia were reported (Hu et al., 1981). A great deal of attention has been dedicated to the implications of the redistribution of radionuclides originally present in the mineral ores used by the phosphate fertilizer industry (Moore, 1967; Menzel, 1968; Spalding and Sackett, 1972; Eisenbud, 1973; Guimond and Windham, 1975; Guimond, 1976; Roessler,

Jan 1, 1981

By J. Hunter

The Highland Uranium Project in Wyoming is an in-situ leach (ISL) facility owned and operated by Power Resources Inc. It is the largest uranium producer in the U.S. and the largest uranium producer by ISL in the western world. With its limited capital investment and low operating costs, the ISL technique has been demonstrated to be an effective and environmentally sensitive method for recovering minerals from these low grade and otherwise uneconomic orebodies.

Jan 1, 1996

By A. W. Wensel

The adsorption behavior of sodium oleate on brucite, Mg (OH)2, has been studied by Fourier transform infrared spectroscopy. Both internal reflection and diffuse reflection (DRIFT) methods were used to characterize the adsorbed oleate on brucite. DRIFT measurements were shown to be quantitative, and an equilibrium adsorption isotherm was obtained. The conformational behavior of the adsorbed oleate was investigated as a function of adsorption density. It was found that at sub-monolayer coverage the alkyl chains of the adsorbed oleate had more ?gauche? character than at multi-layer coverages. Also, DRIFT spectra revealed that the adsorbed species were magnesium dioleate. For internal reflection measurements single crystals of MgO were hydrolyzed to form a thin Mg (OH)2 layer.

Jan 1, 1994

By J. LeRoy Peterson

This paper presents some of the theoretical aspects as well as some results of actual plant operation of the Ty-Hukki Classifier. Dual classification steps within a unit vessel are achieved by controlled separation of the sand product under turbulant flow conditions, followed by further classification under strictly laminar flow conditions. Plant operation has shown some of the benefits of the superior sharpness of classification to be reduction of circulating load in grinding circuits, prevention of overgrinding, increase in mill feed rate and consequent reduction in cost per ton of ore.

Jan 1, 1966

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits; thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium.

By W. C. Dailey

The National Steel Pellet Company is owned by National Steel Corporation, managed by the M. A. Hanna Company and located near the town of Keewatin in northern Minnesota. Annually, the concentrator processes 15.24-Mt (15.0 million It) crude taconite with eight 8.2-m diameter by 5.5-m long (27 ft x 18 ft) wet semi-autogenous (SAG) mills to produce 4.57-Mt (4.50 million It) of iron ore pellets. To improve operating costs and primary mill grinding circuit efficiencies, a task force on liners was formed with the operation, maintenance and engineering staff at N.S.P.C. along with the local supplier of mill liners. Results of the task force recommendations since 1980 along with improvements made in the primary circuit operations, are presented. Mill Liner Design and Metallurgy Changes The primary mill liner task force was formed in 1977. Its function was to improve the operating costs and milling efficiencies of the ten 8.2-m x 5.5-m (27 ft x 18 ft) wet SAG mills that were operating at the time. The SAG mills are driven by two 3500 HP motors drawing a total of 5450 kW at 76% of critical speed.

Jan 1, 1985

By Helmut Goehring

Surface mining has been used primarily where deposits of minerals were exposed or close to the surface. Surface mining can, therefore, be considered the oldest branch of mining. As the most accessible deposits became uneconomical because of the lack of suitable high capacity conveying systems, deep mining took its place. Only in the twentieth century was this trend reversed as high capacity production and conveying systems were developed. This rapid development was triggered by the steadily increasing demand for raw materials and fossil fuels, as well as by the ever increasing ratio between overburden and deposits.

Jan 1, 1982

By W. B. Weston

To mining people who have experienced the tremendous expansion of existing operations and the development of new properties over the last several years we do not have to point out the difficulties in hiring skilled equipment operators. To those of you who have opened operations in some of the more remote places in the world this is not just a difficulty. It is an impossibility. Your only recourse has been to try and train whatever manpower has been available. Depending upon your success in training, the next problem has been to keep them. On todays modern equipment, the skill of the operator remains as the greatest single variable affecting the performance of the machine. On a blast hole drill, for example, a skilled operator will get good production footage, acceptable bit life and minimal machine downtime The unskilled operator will not only fail to get the acceptable production footage but all too frequently this failure is coupled with low bit life, high repair costs and excessive machine downtime. Even between experienced operators, on identical machines, in the same kind of material we find significant variations in performance. It is, therefore, the skill of the operator, not just his experience, which makes the difference. The problem, as presented to us by our customers, has been to find a way for the unskilled man, with minimal training, to match the performance of the most skilled and experienced operator. The obvious answer is automation.

Jan 1, 1970