Search Documents

By J. A. Herbst, L. B. Hales, R. Zaragoza

INTRODUCTION The Control Problem The need for automatic control in flotation plants stems from frequent and randomly occurring disturbances to the feed slurry. Typical disturbances occur in the solids feedrate, the slurry percent sol ids, and the mineralogy and flotability of the gangue and valuable minerals. In plants where semi -autogenous grinding mills (SAG) are used, feedrate changes are very large and changes in feed percent solids of 1m or more are common. Mineralogy changes between valuable minerals are common, as are changes in the host gangue rock. As these changes occur, the operator can attempt to compensate for them by making adjustments to the flotation cell levels, the dosage rates of the collectors and frothers, the pH, and in some cases the aeration rate of the cells. This problem is sometimes complicated by the fact that different sections of the flotation plant will be processing different ore types at the same time. Potential Savings with Control Flotation control brings about savings or plant improvements in two areas; the first is in improved metallurgy and the second is in reagent savings. Improved metallurgy includes increases in the average plant recovery and achieves target concentrate grade level s more consistently. Average recovery increases between 1.0 and 5.0 percentage points have been widely reported (Paakkinen, 1979; Sutherland, 1984). Reagent savings of up to 40 percent have also been reported (Hales, 1985). VARIABLES OF IMPORTANCE Control led, Manipulated, and Disturbance Variables The initial step in the analysis of the flotation control problem is identification of important variables which can affect the efficiency of separation. The efficiency of separation is represented by a group of controlled variables which can quantify the performance of a flotation circuit. This group includes variables such as grade, recovery, tonnage through- put, and circulating loads. The efficiency of separation of a flotation circuit may generally be defined by a grade recovery map, where each point on this map re- presents a set of operating conditions (see Figure 1). However, the combination of operating conditions must be set to operate close to the economic optimum. The group of operating variables which are changed in order to achieve desired circuit performance are called manipulated variables and can be classified into two

Jan 1, 1986

By D. D. Harbuck

Previous studies at the U.S. Bureau of Hines have shown that only 70 to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the Bureau developed and researched the hypothesis that minor amounts of germanium and zinc silicate, both present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of silica gel formed increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1991

By Al Sylvester

The drill-and-shoot excavation of the two underground Pumphouses for the Metropolitan Sanitary District of Greater Chicago's Mainstream Pumping Station is described. The construction sequence involved the concurrent excavation and support of the two 19.2 m (63 feet) wide by 83.6 m (274 feet) long by 29.3 m (96 feet) high caverns. Excavation was interrupted after taking the 6.1 m (20 feet) high top heading in order to cast-in-place a 0.2 m (8 inch) thick by 19.2 m (63 feet) wide concrete arch. The remaining 23.3 m (76 feet) of rock was then excavated in benches below the concrete arch. PROJECT DESCRIPTION Twenty-four kilometers (15 miles) southwest of the city of Chicago, Peter Kiewit Sons' Co., in a joint venture with John F. Shea Co., and Kenny Construction Co., has successfully completed the construction of the Mainstream Pumping Station for the Metropolitan Sanitary District of Greater Chicago. The five year, 169 millon dollar project is a vital component in Chicago's Deep Tunnel and Reservoir Plan in that its function is to lift the sanitary/ storm sewage back up to grade from 107 m (350 feet) below ground, and pump it to the treatment facilities 8 km (5 miles) away.

Jan 1, 1985

By A. S. Malicsi, M. D. Baker, I. Iwasaki

Fine grinding may he required for- some coals to remove sulfur and ash or to prepare coal-water slurry. Fine grinding leads to increased hall wear and its effect on the surface properties of the ground coal becomes of concern. Marked hall wear - tests were performed to study the effects of oxygen, pH, the soluble species of coal, and the addition of pyrrhotite on hall wear. The synergistic action of coal and oxygen greatly enhanced the corrosion of mild steel halls during grinding. Elec.trochemica1 measurements on a mild steel electrode in coal slurries and SEM observations of grinding hall surfaces were carried out to explore the corrosive wear mechanism.

Jan 1, 1991

By Y. Lin

The objectives of this investigation were to study the zeta potential characteristics of a Powder River Basin coal in water and to study the effects of zeta potential on the agglomeration of coal particles. The electrokinetic measurements show that the zeta potential of the coal is dependent on pH, temperature, coal concentration and contact time with water. The effects of various additives for changing the zeta potential of the coal were also evaluated. It was found that the strength of the coal agglomerates is increased when the zeta potential diminishes. Neutralizing the zeta potential enhances agglomeration. Therefore, it is important to control the zeta potential of coal to achieve optimum performance in coal-particle agglomeration.

Jan 1, 1997

By R. E. Johnson, M. Schipper-Zablotskaja, B. R. Palmer, van Sandwijk A.

A procedure has been developed for the removal of zinc from acid solutions containing aluminum, silicon, calcium, magnesium, sodium, potassium and manganese ions and high concentrations of chloride ions. The first step of the procedure involves the precipitation of aluminum and silicon at pH 4.2. The second step, the removal of the zinc as zinc oxide, was studied in detail to get in- sight into the formation of oxychlorides. A diagram was developed giving the conditions at 75O C under which the formation of oxychlorides is avoided. Under optimal conditions a zinc oxide with less than 0.5 weight percent of chloride can be produced from 11 - 16 g/l chloride solutions.

Jan 1, 1993

By R. L. Miller

The potential for recovery of enriched uranium from spent nuclear fuel which has been consolidated into a nuclear waste form was explored in the studies reported here. The waste form of interest is iron-enriched basalt (IEB)--a silicate-based, fused-cast ceramic. IEB samples were prepared containing fuel assembly materials that simulate the core debris of Three Mile Island Unit II;1,2 the nominal composition of the consolidated waste form is given in Table 1. Ore Types The IEB samples, or man-made uranium ores (MMUO), are in two different mineralogical forms. Each MU0 was made by melting the constituent materials and holding at about 1500°C for 1 h. The MMUOs were then heat treated to control crystallization and crystal growth and then cooled to room temperature.

Jan 1, 1983

By E. C. Ekedahl, R. J. Heath

Introduction Potassium, together with nitrogen and phosphorous, is an essential nutrient required for growth. Since all living things need potash, the major demand for potash - about 95% of the total - is as a fertilizer. Agricultural productivity has increased dramatically in recent times. This increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows then that potash will always be in demand. There is no substitute. Other fertilizers that contain phosphorous (P) and nitrogen (N) are complementary and not competing products. Fireplace ashes (pot-ashes) have a relatively high potassium content. Their value as a fertilizer had been recognized for centuries. But today's potash industry did not begin until deposits of potassium-rich ore were discovered and exploited in Europe during the 19th century. Canadian potash development Potash in Saskatchewan was first recognized in 1943. It was discovered as a byproduct of an oil exploration program. But it was several years later before the existence of a major commercial deposit was acknowledged, and not until 1951 that the first attempt at development occurred. That attempt was unsuccessful. The shaft flooded and was abandoned. It did, however, demonstrate the need for new technology to penetrate the waterlogged Blairmore layer. This was eventually developed and the first mines were brought into production in the early 1960s. Once the technology was available, and the extent and quality of the potash beds became known, a number of companies proceeded to develop mines. By 1970, seven mines were in operation and three more were nearing completion. Combined, total capacity then was 7.6 Mt/a (8.4 mil¬lion stpy) K20. At that time, world potash consumption was about 15 Mt/a (16.5 million stpy). This increase in supply from Canada produced a large potential surplus that shattered the prevailing balance between supply and demand. Although world demand increased steadily throughout the 1960s and early 1970s, it was several years before world supply and demand were again in balance. Saskatchewan capacity has been expanded a number of times. It now stands at 10.7 Mt/a (11.7 million stpy) K20. Actual production has not approached this figure, however. Two new mines in New Brunswick have recently been built with a combined annual capacity of 1.2 Mt (1.3 million st) K20. Total Canadian capacity of about 12 Mt/a (13 million stpy) now amounts to 30% of world capacity. Central offshore marketing organization Canadian Potash Exports Ltd. (Canpotex) was created in 1970 as the offshore marketing organization for Canadian producers. Canpotex is owned by Saskatchewan producers and is their exclusive marketing organization for offshore business. Each company handles its own sales in Canada and the US, but all sales to other markets are handled through and by Canpotex. The Saskatchewan industry has an ore body of a size and consistency unmatched anywhere in the world. Large efficient mines have production costs that compare favorably with other producing countries. On the minus side, Saskatchewan is remote from most major markets. It therefore needs the ef¬ficiencies that stem from one organization that coordinates all offshore shipments and minimizes distribution costs. Agriculture guides potash market In the period following World War II, potash was a classic growth industry. World demand increased each year from 1945 to early 1970s. Since then, demand has been more erratic. Some years show substantial increases, but are followed by significant declines. For about the last decade, the pattern has been unclear and future demand has become correspondingly difficult to predict. North America and Europe together account for about 40% of the world potash consumption. In both areas, farming is characterized by surplus production, declining crop prices, and expensive government support programs. Under those circumstances, farmers respond by minimizing input costs. Fertilizer is one of the items they reduce. Potash is retained in the soil. It is possible to reduce potash application with no immediate deterioration in crop yield. The lower yields occur only when potash levels are depleted. So, farmers can econo-

Jan 12, 1987

By Tim O’Neil

Big and getting bigger. Barrick Gold Corp., the third-largest gold producer in the world, began production in September — ahead of schedule — at its Meikle Mine. At a scheduled full production rate of 12.4 t/a (400,000oz/year), it will be the largest producing underground gold mine in the United States. The $180-million Meikle Mine is located on Barrick’s Goldstrike property in Nevada and has 205 t(6.6 million oz) of gold reserves. The compact Meikle deposit has an average ore grade of 23 g/t (0.68 oz/st), making it one of the highest-grade mines in the country.

Jan 1, 1996

By P. Somasundaran, A. Sivakumar

Surfactants and polymers are used in a number of processes such as flotation and flocculation. The structure of the adsorbed surfactant and polymer layers control the interfacial properties of the solid and hence an understanding of the structure of the adsorbed layers at the molecular level is essential. In this paper, a review of different spectroscopic techniques (fluorescence, electron spin resonance and Raman) used to characterize the adsorbed layers [in-situ] is presented. Information on the micropolarity, microfluidity and size of the surfactant aggregates was obtained and the growth of the adsorbed layer was followed. [In-situ] conformational states of polymers at the solid/liquid interface were determined for different pH values.

Jan 1, 1989

By D. D. Harbuck

Previous studies at the US Bureau of Mines (USBM) have shown that only 70% to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the USBM developed and researched the hypothesis that minor amounts of germanium and zinc silicate, present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of formed silica gel increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1994

By R. Z. Pyrih

Pressure/ ,acuum lysimeters were used to instrument column tests containing several lifts of tailings slurry, and to sample pore water as the tailings lifts dried. The results of the column testwork demonstrated that air oxidation of sulfide minerals associated wilh the tailings residue neutralized the alkalinity of the tailings pore water. Neutralization of the alkaline pH volatilized cyanide which, in turn, destabilized copper-cyanide complexes and caused the precipitation of insoluble copper from solution. Analyses of pore water samples for microbial activity indicated high plate counts. The presence of viable microorganisms in the pore water implied that degradation of cyanide was enhanced by growth and activity of cyanide-consuming microorganisms in the tailings material.

Jan 1, 1991

By William E. Foreman

Editor's Note: For purposes of uniformity throughout this book, Coal Preparation, 5th Edition, the editors have advocated the use of the U.S.A. Sieve Series of testing sieves (see Table 6-2) as the testing sieves of modem choice. The adoption and use of the U.S.A. Sieve Series and its forerunner, the Tyler Standard Screen Scale, has for over seventy-five years introduced uniformity into reports; has simplified the comparison of results; and has provided control for operation of modem coal preparation circuits. While a full explanation of the differences, and more importantly the similarities of these two measuring systems cannot be stated here, it is felt that a brief clarification of terms is in order. The difference between the U.S.A. Sieve Series and the Tyler Standard Screen Scale Sieve Series is the identification method. Tyler Screen Scale sieves are identified by mesh designation with the width of opening varying by the square root of two, or 1.414 times the width of opening in the previous sieve. The U.S.A. Sieves are identified by openings in millimeters or microns and also arbitrary numbers which do not necessarily mean the mesh count; this series uses width of opening variations in the order of approximately the ratio of the fourth root of two, or 1.189. Tyler Standard Screen Scale and U.S.A. Sieves can be used interchangeably, and to avoid confusion the nameplate of all Tyler Screen Scale sieves show the U.S.A. Number, while all U.S.A. Sieves show Tyler Screen Scale mesh equivalent numbers on the nameplate. INTRODUCTION Sizing is the process of separating mixed mineral particles into groups of particles all of the same size, or into groups in which all particles range between definite maximum and minimum sizes. This chapter applies the modem mechanical screen and the liquid-solid cyclone (hydrocyclone) to the process of sizing solid particles as applied to coal preparation. Screening is a mechanical process that separates particles by size. Modem coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modem preparation plants is done for the following reasons: 1. Removal of fine coal before a size reduction step. 2. Size separation of the coal into a coarse and fine fraction for sized products or for processing in coarse and fine coal circuits. 3. Recovery of heavy media from heavy media coal cleaning circuits.

Jan 1, 1991

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

9.1 INTRODUCTION There are approximately 70,000 abandoned coal mines nation¬wide, which is about 35 times the number of underground coal mines presently operating. The US Bureau of Mines estimates that there are over 8 million acres of undermined land due to the extraction of coal, metals, and nonmetals. Subsidence has affected more than 2 million acres, and more than 99% of the subsidence is related to underground coal mining. There is reason to believe that some of the remaining 6 million acres of the undermined land have a high potential to subside. The expansion of housing, highways, commercial structures, and other facilities has required the use of many areas that are underlain by abandoned coal mines, and this growth will continue. Many subsidence problems are derived from the collapse of aban¬doned underground coal mines. There are numerous abandoned mine workings in the anthracite fields of northeastern Pennsylva¬nia, in the Appalachian bituminous fields, the Illinois Basin, the Rock Springs, Wyoming area, and other areas of the United States (Gray et al., 1976). Various room and pillar patterns of mining have been used in the dipping anthracite seams and the nearly flat-lying bituminous seams with considerable variation in the per¬centage of coal extracted. The progressive deterioration of pillars, mine floors, and mine roofs after long exposure to air and water may later result in the collapse of strata over the mine entries, the crushing of the remaining coal pillars, or the bearing failure of the mine floor beneath the coal pillars. Subsidence then results as the collapse reaches the ground surface in the form of differential strains, depressions, cracking of the ground, and sinkhole devel¬opment. Subsidence over active longwall mines, which occurs concurrently with mining or is completed within a short period following coal extraction, has been studied extensively over the past decade. On the other hand, subsidence over abandoned coal mines receives little attention by the researchers, mainly because it is difficult to predict and takes place decades after mining has ceased. The techniques of investigating the subsidence events over abandoned coal mines are similar to those employed for active mines except that at the outset, it is necessary to determine whether or not the subsidence events are mining-related (Chugh et al., 1986; Cummings and Singh, 1986; Peng and Hsiung, 1986). This calls for the identification and confirmation of abandoned mine workings under or near the affected surface structures. Gen¬erally old mine maps, if available, are acquired, the surface bore¬holes are drilled for confirmation of the accuracy of the mine maps and determination of the potential for continued subsidence. Sub¬sidence monuments are established and periodic surveys con¬ducted to determine the amount and trends of surface movement in and around the affected surface structures; surface boreholes are used to investigate the integrity of the underground structures (i.e., roof, coal pillars, and floor) by TV camera. They are also used for monitoring the vertical and horizontal movements of the subsur¬face strata by Sondex (FPBX) and inclinometer (PFBI), respec¬tively, for determining the continuity of the subsidence events. Tape extensometers, crackmeters, etc., are used to monitor the development trends of major cracks in the structures or on the ground. These data are used to identify the causes of the subsidence events. Finally, abatement methods are selected to stabilize the structures. It must be noted that most subsidence events over abandoned coal mines are reported after the fact, and investiga¬tions are begun some time after reporting, that the subsequent measured movements are generally much smaller than that at¬tained in the active mines, and that due to lack of knowledge about the damage conditions and the exact location of the abandoned mine workings with respect to the affected surface structures, the precise causes of surface subsidence or surface structural damages are in most cases very difficult to identify. 9.2 TYPES OF SURFACE SUBSIDENCE According to Gray et al. (1977), after examining 354 incidents of subsidence above abandoned mines in the Pittsburgh metropol¬itan area, the subsidence features have a mean diameter (i.e. the average of long and short dimensions) from less than 1 ft to 1600 ft, with 84% less than or equal to 15 ft; the subsidence features have a depth ranging from less than 1 ft to 48 ft, with 89% less than 25 ft; 66% of the subsidence features are deeper than they are broad. Nearly 59% of the subsidence features occur with overbur¬den less than 50 ft thick and 81% less than 100 ft thick. No subsidence features occur with overburden thicker than 450 ft (Fig. 9.1). Occurrence of subsidence incidents varies from imme¬diately to more than 100 years after mining (Fig. 9.2). In analyzing the characteristics of approximately 3000 chim¬ney subsidence features along the Colorado Front Range, Matheson and Eckert-Clift (1986) examined historical aerial photographs on 4- to 14-year intervals between 1937 and 1967 and found that the majority of observable surface subsidence features occurred within 30 to 40 years after mining. According to Gray et al. (1977), the most prevalent subsi¬dence features over abandoned mined land are sinkholes, with depths of more than 3 ft, and troughs or sags, usually less than 3 ft deep. Sinkholes are steep-sided pits, while troughs are shallow depressions much wider in area than sinkholes. A. SINKHOLE SUBSIDENCE A sinkhole is caused by the collapse of a mine roof that works its way upward. If it is not arrested during the process it will eventually reach the surface and emerge as a sinkhole. The process is governed by the thickness and character of the overburden, the width and height of the mine openings. Sinkholes are usually 3 to 20 ft deep and may be 2 to 40 ft in diameter, although most are fewer than 16 ft across (Gray et al., 1977; DuMontelle and Bauer, 1983). Newly formed sinkholes have steep sides with straight or bell-shaped walls. At times, they appear to be conical in profile with the apex upward. If the topsoil collapses, the top portion will widen to form an hour-glass shape. Sinkhole subsidence usually occurs over abandoned mines less than 165 ft deep (Hunt, 1979). Matheson and Eckert-Clift (1986) found that chimney sink¬holes are likely to occur when the ratio of overburden thickness to mining height (h/m) is less than 4 to 5. When h/m is between 5 and 10 to 11, the potential occurrence of chimney sinkholes decreases rapidly. When h/m is more than 10 to 11, less than 10% of the mine openings that collapse will induce sinkholes on the surface.

Jan 1, 1992

The main goal of this paper is to present readers with recommendations for choosing coaxial cables appropriate for mining applications of Time Domain Ref 1 ectometry (TDR) to monitor rock mass movements. Prior to discussing the recommendations, mining applications are illustrated with examples and the operating principle of TDR is discussed briefly. Items that affect the result of the monitoring system performance include the coaxial cable selected, the grouting material used, and the installation procedure.

Jan 1, 1986

By R. D. Doepker, P. L. Drake

The dissolution of metals from various metal- mine tailings has been studied through a series of submerged tailings batch tests at US Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97% saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79% or 70% saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained early constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1991

By Bok-youn Kim

Presently, mobile diesel equipments contributes a lot in improving the economical feasibility of underground mining and tunneling operations. Even in Korea, quite a large number of diesel equipments is being applied to the underground workings already. This paper introduced the production procedure, characteristics and evaluation technology on diesel particulate matter(DPM) that is known as a carcinogen For easy measurement of DPM using laser dust monitor, the conversion factor(K) to gravimetric concentration was acquired. The field measurement of DPM was conducted to make a comparison between locally manufactured on-road equipments and imported equipments specially designed for underground use. According to the Government regulation revised h 1996, it was learned that the critical pollutants among the diesel exhaust is DPM instead of NOx which have been considered as a critical pollutants.

Jan 1, 1997

By Frank R. Cappuccitti

This paper will deal with current market trends for sulfide mineral collectors in three distinct parts; the global market for sulfide collectors, collectors as tools to solve mineral processing problems and new collector Research in the 1990's. The global market and manufacturing of sulfide collectors will be detailed as well as the trend towards using increasing amounts of specialty products. The use of Total Quality Concepts for laboratory and plant evaluations of new products will also be discussed. Research in the 1990's for sulfide collectors will need to focus not on the development of new chemical species but on the application of the new technologies that have already been developed.

Jan 1, 1994

By B. P. Atkin, D. W. Brown

The handleability monitor has been specifically designed to provide a simple, rapid and on-site assessment of the whole or part consignment of a coal blend in its ‘as-received’ condition. Evaluation has been carried out at a number of coal-handling plants, on both metallurgical and power station coals from a variety of sources world-wide. The results which are used to predict which coals could routinely pass through a handling plant at line capacity, without causing blockage or delay, have also been correlated with moisture, ash and size analyses of the coal to develop a predictive model of handleability.

Jan 1, 2000

By V. F. Swanson

M&MP, Volume 6, No. 4, November 1989, pp. 190-196

Jan 1, 1990