Search Documents

By K. A. Natarajan, J. M. Modak

A review of published literature on the biosorption of metals using nonliving biomass is presented. Factors such as pH, temperature, initial metal concentration, biomass loading, the presence of co-ions and the pretreatment of biomass influence the metal uptake by biomass. Although few generalizations are possible, unified theories regarding the mechanism of uptake are not available. Therefore, the above aspects of metal biosorption have to be defined individually for each biomass and metal-ion pair.

Jan 1, 1996

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985

By Eberhard Stolarski, Michael Tacke

When the oxidized surface gold deposits are mined out, the underlying refractory gold ores become the challenge of treat­ment systems. The size and value ofrefractory gold ore reserves are a function of recovery efficiency and operating cost. The start-up of LURGI's gold roasters at NEWMONT's Carlin site has established whole ore gold roasters as a key to high gold recoveries. The ores from several deposits of the Carlin trend are roast­ed utilizing LURGI / NEWMONT technology, which has achieved gold recoveries approaching 95%. This is in dramatic contrast to the traditional perception that roasting is limited to gold recoveries in the mid 80's. Extensive investigation in pilot scale is required to achieve stable high gold recoveries for most variables in the ore body. The key question for all pilot tests is the classic question of (ROM) run of mine ore roasting or concentrate roasting. All variables are dominated by the leaching/ recovery char­acteristics of the natural ores. The degree ofrecovery improve­ment by roasting / calcining establishes the frame of the eco­nomical conditions. The full range of flexibility is required for the design of the plant to allow for ore variations in heat values, combustible con­tents, agglomeration behavior and off-gas composition. The variables in the ore body influence, therefore, the price of the plant proportionally to its flexibility. Concentrates are usually fairly stable in composition, com­bustion behavior, heat values and particle size since they are a product of the very selective flotation process. Flotation is not the successful process step when the tailings remain high in refractory gold contents.

Jan 1, 1996

By August V. Castelli

Drilling fluids have changed over the years from water and/or water frequently mixed with local clays to scientifically com- pounded materials (mud). This change has occurred due to changes in drilling methods from percussion to rotary: depth maximum from 21 m in the first oil well to more than 9 000 m; and variety in types of well or hole to gas, oil, water, and mineral exploration. Environmental concerns about the composition of the fluid as to heavy metals and oil on the cuttings has recently caused changes in the materials used in the mud. The drilling fluid should perform the following functions (Darley et al., 1980): 1) Carry cuttings from beneath the bit, transport them up the annulus, and permit their separation at the surface. 2) Cool and clean the bit. 3) Reduce friction between the drilling string and the sides of the hole. 4) Maintain the stability of uncased sections of the borehole. 5) Prevent the inflow of fluids-oil, gas, or water-from permeable rocks penetrated. 6) Form a thin, low-permeability filter cake which seals pores and other openings in formations penetrated by the bit. In addition to these, the fluid should: 1) Not injure drilling personnel nor be damaging or offensive to the environment. 2) Not require unusual or expensive methods of completion of the drilled hole. 3) Not interfere with the normal productivity of the fluid- bearing formation. 4) Not corrode or cause excessive wear of drilling equipment. A number of industrial minerals, chemicals, and other materials are used as additives in the drilling fluid to accomplish these functions. Industrial minerals make up the highest percentage of the additives in a drilling fluid. Drilling fluids are classified according to their principal components: water, oil, and gas. If the major component is either water or oil, the component along with the suspension of solids, cuttings and additives is referred to in the trade as a mud. The largest use of some industrial minerals, such as barite and bentonite, is in drilling muds. For other materials, such as gypsum and limestone, drilling usage is only a small percentage of total demand. RAW MATERIALS [Table 1] lists the industrial minerals used in drilling fluids, their form, specifications, and uses. Each raw material will be discussed as to its mineralogy, physical and chemical properties, and the location of major deposits with respect to drilling fluids. Attapulgite Attapulgite is a crystalline hydrated magnesium silicate clay mineral, prized for its viscosity in saline waters. The particles are needle-like rather than the platelets common to most clay minerals. The specific gravity is 2.5 and the Mohs hardness is 1 to 1.5. Attapulgite is one of the materials sometimes referred to as fuller's earth. The major producing areas in the United States are southern Georgia and northwestern Florida. It also is mined in Spain, Senegal, the Republic of South Africa, Turkey, India, and Australia. Barite Barite is crystalline barium sulfate. It has a high specific gravity for a non-metallic mineral, 4.5 when pure, and is used as a weighting agent. Generally, the specific gravity ranges from 4.20 to 4.35. It is relatively soft with a Mohs hardness of 3 to 3.5 and is not very abrasive. Barite is inert, non-toxic, and clean to handle. Common contaminants are quartz, iron minerals, gypsum, and calcium carbonate. If there is considerable gypsum in the barite, it will thicken the mud. The major deposits in the United States are in north central Nevada, near Battle Mountain. The major producing countries, other than the United States, are China, India, Mexico, the former USSR, Turkey, and Morocco. The major deposits in India and Nevada, and some in China, are stratiform, commonly quite pure bodies in bedded sedimentary rocks.

Jan 1, 1994

By Donald A. Dahlstrom, Wai-Ping Kam

The mineral industry and individual processing plants are large consumers of energy. While energy conservation has received some attention in the present Federal Administration National Energy Strategy proposal it is obvious that the mineral industry should also continue to emphasize energy consumption reduction for important economic savings alone. As indicated by other studies, comminution is the largest single consumer of energy in the mineral processing plant (1.3% of total electrical energy consumption in the U.S.A.).1 Fine grinding is the largest portion of this amazing statistic. While substantial energy savings have been demonstrated by new machine developments and improved control methods, undoubtedly there are additional areas in comminution where substantial progress can be made. Some time ago, the U.S. Department of Energy published a report on "Comminution and Energy Consumption" by a committee composed of experts in the field of comminution from industry and academia. They identified the following potential for energy savings by specific areas? Classification device design 9-13% Comminution device design 3-16% Control 9% Grinding additive 3-6% Materials 3% It is apparent that the classification device had the first or second highest savings potential. Obviously, serious research consideration must be given to this technology area. A series of three papers have previously been written on the subject of two stage classification research work for ball mill operation by the authors. Accordingly, a brief review will be made. Previous Research Results on Two Stage Classification The hydrocyclone was selected as the type of classification equipment for this study as it represents by far the majority of the devices used in ball milling. While four different hydrocyclone circuits have been proposed by others,3 only two were considered in this work as illustrated in Figure 1. Flowsheet A is truly counter-current in nature in that the product from the ball milling circuit is taken from the first stage overflow

Jan 1, 1992

By S. Chander

The effect of pretreatment potential on the response of a gold electrode for Eh measurements in sulfide solutions was examined in terms of measured Eh values and electrode response time. The electrode response time is defined as the time required for the electrode to reach a steady-state value. The relationship between measured Eh values and the hydrosulfide ion concentration is established. The effect of pH, the reversibility of the gold electrode in the sulfide solutions, and the reproducibility of measurements are also investigated. A mixed potential theory is proposed to explain the observations.

Jan 1, 1989

By J. Hoover

Real growth in the economy, increasing demand for electricity, and consumer stockpiling for a possible United Mineworkers of America (UMW) strike in October made 1984 a banner year for coal. Production and consumption climbed to record heights. Precautionary purchases brought inventories close to the peak levels of early 1981 when coal miners walked out for 72 days. Production slowed in the fourth quarter after labor and management concluded negotiations without a walkout. But output in every major coal producing state showed significant gains during the year US coal production totaled 807 Mt (890 million st) in 1984. This is a 13.8% increase over 1983 output. Lower production rates, principally in Appalachia, and sustained demand in the final quarter put downward pressure on coal stocks by the end of the year. Demand All market sectors experienced greater requirements for coal in 1984. Electric utility coal consumption increased 6.3%; exports climbed 4.8%; coke plants consumed 18.9% more coal; coal requirements in the other industrial sector expanded by 11.8%; and consumption in the residential/commercial sector rose 8.1%. Domestic consumption of coal reached a record 718 Mt (791 million st) in 1984. This is a 7.4% gain over the previous consumption high of 668 Mt (737 million st) in 1983. Electric Utilities The 4.6% increase in electric power generation in 1984 was coupled with expanding coal use relative to other energy sources. This resulted in a 6.3% rise in coal consumption, totaling 603 Mt (664 million st) for the year. Thirty-eight of 45 states where coal-fired electric power plants were operating shared in the 36-Mt (39 million-st) increase in electric utility coal consumption

Jan 5, 1985

By Andres Salazar, Carlos Delgado Robles, Richard K. Preece

The paper discusses the evolution of the geometallurgical model at the Escondida mine in northern Chile, the world’s largest copper producer. It highlights the transition from early metallurgical forecasting methods to a comprehensive model that includes spatial distribution of metallurgical forecasts. This model helps in planning and adapting to the variability in ore characteristics, such as hardness and mineralogy, which affect processing performance.

Dec 1, 2023

By Young C. Kim

In the past, underground coal mine planning has traditionally focused on the mine design n aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most of the underground coal mines within the U.S. With the enactment of the clean air act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the BTU contents of coal are of equal importance from boiler efficiency standpoint. Thus, the time has come when the coal mine planning must incorporate the coal quality control aspects as well as the traditional safety and efficiency aspects.

Jan 1, 1983

By V. F. Hollister

Copper and gold were discovered in the Copper Canyon area of the Battle Mountain district of Lander County, Nevada, in August of 1866. By 1876 a gravity plant was con¬centrating oxidized Copper Canyon copper-gold ores. The history of mining in the district to 1967 has been summarized by John E. Frost (in press) as a case history of the discovery of the Battle Mountain porphyry copper deposits. His summary is not repeated here; rather, the present case history covers exploration since 1967, primarily for gold ores. Subsequent to the construction by Duval of facilities to mine the porphyry copper deposits in 1967, Duval established a geologic staff at the mine to continue district exploration. The staff was guided by David W. Blake, who acted as chief geologist for Duval's exploration in this part of Nevada. Blake's activities led to the publication of numerous technical articles, including his contribution to the US Geological Survey Professional Paper 798-B. A part of that volume is attached as a reprint (pages 23 through 66) as an explanation of the geological setting of mineralization in the district. The work by Blake and his staff recognized metal zonation in the skarn environment at Copper Canyon, and their studies were incorporated in the development of the Tomboy-Minnie gold deposits that are peripheral to the porphyry. Exploration continued beyond the immediate vicinity of the porphyry and the Fortitude ore zones were discovered. These skarn deposits are described in the attached article by Wotruba, Benson, and Schmidt, published in the July 1986, MINING ENGINEERING. The continued exploration successes at Battle Mountain reflect on the well organized and effective exploration team developed at the mine. The team has provided successive discoveries in a district known mostly for ore bodies that are exhausted in a few years' time.

Jan 1, 1990

By M. G. Gorman

The effects of particle size, particle shape and degree of aggregation on n-dodecylamine flotation of -20 µ m quartz and glass beads were studied. A microflotation cell suitable for use with very fine particles was used in the flotation experimentation. Degree of agglomeration of particles was estimated by comparing size distributions of the quartz and beads in a dispersed system to size distributions in systems in which the collector was present. Results obtained show that in such flotation systems the fine particles are not generally present as individual particles during flotation but rather as aggregations. However, the quartz floats more readily than the beads indicating that there are some shape effects in the systems, considering the large specific surface areas of the materials it also appears that substantial amine consumption in the systems may limit flotation or lead to a requirement of greater reagent dosage for equivalent flotation to that tor larger particles.

Jan 1, 1990

By Kyle A. Perry, Ethan A. Steward

The mining of underground coal presents several hazards for miners, including the risk of an explosion fueled by methane gas and coal dust. Methane gas, produced during coal formation, can continuously leak into old workings and build up through its lower explosive limit. Underground coal mines are required to maintain safe conditions, either by ventilating old workings or sealing them off using approved methods. Seals must be designed to withstand instantaneous pressures for a minimum of four seconds. A design strength of at least 50 pounds per square inch (psi) is required for atmospheres monitored and maintained inert, 120 psi for non-inert or not monitored, and greater than 120 psi for special cases. Due to the high cost and testing environment availability, most mine seals are designed through calculations and computer modeling and not subjected to full-scale testing in a representative environment. High pressure is not the only threat that mine seals may be exposed to. During an underground explosion, pressure waves and gas expansion may propel common mine items and objects to a high velocity, generating enough energy to damage mine seals and reduce their strength. Damaged mine seals may fail to contain their rated pressure, allow high pressure gas and fumes to vent through the seal during an explosion, or allow gasses to leak through the seal later after an explosion has occurred. This paper examines the effects of high velocity impacts of common mine materials and items on a reinforced mine seal rated to 120 psi.

Jun 2, 2023

By Edward J. Hasenohr

Geochemical studies were under- taken in the Breckenridge mining district to test the effectiveness of soil and rock-chip samples in high- lighting known mineralization in the district, and in locating sites of possible porphyry-type mineralization, if such mineralization is present in the area. Soil sampling can be done more quickly and more cheaply, but it does not provide a direct site- specific sample of mineralized rock. In well-developed soils, supergene effects may mask and/or displace primary hypogene effects; and even in places where the soils are poorly- developed, as in the Breckenridge district, the masking effects may be felt. Soil anomalies, if present, likely will be of lower amplitude and more diffuse (widespread) than corresponding rock-chip anomalies. On the other hand, detailed rock-chip surveys are more time-consuming and expensive, even though they yield direct geologic information in addition to the chemical data. The goals of the combined soil and rock-chip programs were (1) to com- pare the data from the two; and (2) test the effectiveness in identifying significant chemical anomalies with respect to the geology of the district, as it is presently understood.

Jan 1, 1982

By Robert H. Merrill

7.1-STABILITY OF SLOPES IN SOIL AND ROCK ROBERT H. MERRILL 7.1.1-DESIGN ANALYSIS APPROACHES The analyses of slopes in soil or rock can be made through application of soil- or rock-mechanics principles. In most cases, the material in the slope wall can easily be identified as either a soil or a rock. However, there will be instances where, because of unique characteristics, the soil may behave as a rock structure, or vice versa. By necessity, these unique cases must be identified through experience or critical observation by the engineer, because there are no definitive rules clearly establishing the differences. The most important step in a solution to a slope problem is to define it. Normally, once the problem is identified, a solution usually can be found or a reasonable estimate obtained. The design analysis of a slope wall implies an evaluation of the stresses or forces in the wall, and of the ability of the material in the wall to withstand them. Therefore, the factors influencing a design analysis can be divided into two categories: those which influence stresses, and those which influence the ability of the wall to withstand stress. For simplification, the latter is termed the strength of the soil or rock. Perhaps the basic difference between analyses for soils and those for rock is in the identification of the failure surface. Soils generally do not have an identifiable failure plane. However, some soil layers in a slope wall may have different strengths. A soil slope wall may consist of a thin layer of topsoil overlying a thick, uniform clay, or a topsoil over a gravel or other materials. Therefore, the soil generally does not have a potential plane of weakness that can be identified through observation. On the other hand, rocks normally contain planes of weakness in the form of fractures, faults, joints, bedding planes or other discontinuities weaker than the intact rock, which can be found through observation and/or tests upon rock samples. If the failure surface cannot be identified, the principles of soil mechanics should apply because, in soil mechanics, the failure surface usually is assumed. If it can be identified, then the principles of rock mechanics should apply. 7.1.2-ANALYSES OF STRESSES OR FORCES IN SLOPES All existing methods of soil-slope analysis are based upon interpetations of the Coulomb and Coulomb-Navier failure criteria, commonly termed the total-stress 2nd the effective-stress criteria (Sec. 6.1). The total-stress criterion may be illustrated by the diagram in Fig. 7-lA, which relates the total stress, S, to the cohesion, c: the normal stress, u, and the angle of internal friction, 9, by the expression

Jan 1, 1973

The transfer of Langmuir-Blodgett (LB) monolayers of collector molecules to the surface of mineral crystals is an excellent method for the study of collector adsorption phenomena and is of particular significance in the understanding and development of improved flotation separations. The fatty acid/fluorite and amine/sylvite potation systems were investigated by the Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) examination of transferred LB monolayers of collector molecules at the surfaces of the mineral crystals. The [ir]-A isotherm study of fatty acid and amine, typical anionic and cationic collectors, showed the different packing trends dependent upon the pH and/or type of subphase. This result clearly reflects the effect of pH on compound formation and dissociation of the collector molecules. Identification of the collector adsorption state and confirmation of the validity of the FT-IR/IRS adsorption density equation were included in this research effort. This allowed for a detailed discussion of collector adsorption phenomena. As a result of these experiments, it is possible to relate the hydrophobic character of a surface to the nature of the adsorbed collector structure and thus describe flotation behavior in greater detail. For example, it appears that in the case of oleate/ fluorite the equivalent of an LB monolayer can form spontaneously during adsorption from solution, and this structure is known as a self-assembled monolayer (SAM). Such a state is significantly more hydrophobic than the oleate structure which forms on the calcite surface at an equivalent adsorption density.

Jan 1, 1996

By R. W. Brann, R. C. Freas

Franklin Industrial Minerals operates several mines/quarries, including two room and pillar underground mines. Both of these mines are operated as multiple level room and pillar including heading and bench operations on one or both of the levels. This paper focuses on Franklin’s Crab Orchard, Tennessee mine, which produces both high purity chemical grade limestone and crushed stone for construction applications. The high purity chemical specifications for the chemical grade limestone and filler/extender applications are inconsistent with the non-chemical rock being produced to supply the crushed stone market. As a consequence Franklin has developed a unique mine plan and operation to maintain both product balance and a safe and stable working environment.

Jan 1, 2003

By Daniel Willis, Ryan O’Connell

An 8-foot tall horseshoe adit tunnel located within an abutment of the Mount Morris Dam in Mount Morris, NY required repair of a failed reinforced concrete liner. The adit tunnel is entirely founded within highly weathered shale bedrock units, which induced unloading stress on the original tunnel liner. An epoxy-impregnated carbon fiber fabric wrap manufactured by Sika was chosen to repair the failed adit tunnel liner. Kilduff Underground Engineering completed the design of the tunnel repair utilizing both empirical and numerical methods. Merco Engineering Contractors completed the injection of chemical grout and repair liner installation.

Jun 23, 2024

By David A. Fawcett

An auxiliary cross-pit mining system, working in tandem with the prime excavator, is evaluated technically, operationally and economically for application in the selective removal and replacement of soils and unconsolidated ovezburden. Previous studies on cross-pit technology and applications of this technology are briefly reviewed. Stratigraphy plus pit, operating and economic parameters are assumed and applied in the evaluation and comparison of a base case dragline system with two alternatives - a dragline/scraper-dozer combination and a drag- line/cross-pit system combination. The economics of the proposed cross-pit system favour it as a viable alternative to conventional systems.

Jan 1, 1981

By S. V. Krishnan

Stability of fine quartz suspensions in process water is of concern in several mineral processing applications. In alkaline solutions, the presence of magnesium ions, arising from such sources as water hardness and magnesium-bearing minerals, leads to the precipitation of Mg(OH)2 which coats the surfaces of quartz. The conditions under which heterocoagulation or surface precipitation of Mg(OH)2 on quartz occur and the manner in which they influence the settling behavior of ground quartz was studied by means of settling tests, coating density determinations, zeta potential measurements and electron microscope observations. Coating density was greater when Mg(OH)2 nucleated on the surface of quartz than when the precipitates heterocoagulated on the quartz surface. The settling curves of quartz suspensions in the presence of different concentrations of MgCl2 exhibited a maximum of maxima which occurred at 10-3M MgC12 and pH 11. Interactions between quartz and Mg(OH)2, and flocculation-dispersion characteristics of quartz suspensions in this system are discussed.

Jan 1, 1983

By Joseph L. Condon

The U.S. Department of the Interior, Bureau of Mines, is doing research on methods to obtain premining information on problems such as detection of old mine workings, abandoned oil wells, channel sands, faults, and other geologic features that are undesirable from a production or safety aspect. Techniques being developed to acquire the necessary information include seismic and electromagnetic. The seismic methods include high-resolution seismic and acoustic methods applied from the surface and inseam channel waves applied under- ground. The electromagnetic, or radar, methods are applied from the surface, from boreholes, and from the working face underground. All of these methods are useful under certain site-specific conditions, but none of these methods is universally applicable for all mining conditions.

Jan 1, 1980