Search Documents

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By Jerome A. Westphal

The Middle Mississippi River extends from the mouth of the Ohio River to the mouth of the Missouri River, a distance of about 310 kilometers (km) measured along the river. From its founding in 1764 to the first steamboat arrival in 1817, the City of St. Louis was little more than a trading post. However, with the advent of the shallow-draft steamboat, the Middle Mississippi River rapidly became a major thoroughfare of commerce. In this regard, its importance has been reflected by the development of port facilities at St. Louis and by Federal activity relating to channel maintenance and improvement. First Federal work on the Middle Mississippi River was autho¬rized by Congress in 1824. This work was for snag removal and bank clearing and was directed at reducing the hazards to steamboat traffic, particularly during low-flow periods. During the 1820's and early 1830's, the main channel threatened to move toward the Illinois shore and abandon the St. Louis port facilities. In 1836 and 1837, Congress authorized construction of permanent improvements to keep-the river next to St. Louis (Missouri shore). By 1880, it was recognized that bank clearing activities had resulted in a wider and shallower river which exacerbated navigation

Jan 1, 1977

By M. A. Mahtab

This paper presents the results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block-caving method. The two-dimensional finite element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1975

By Michael A. Trevits

A mine fire represents one of the most dangerous and challenging safety issues facing underground mine operators. Given the right circumstances, a mine fire can occur at any location in the active or abandoned mine workings, can quickly grow beyond control, and threaten the welfare and livelihood of the entire underground workforce. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), has been conducting an in-depth program of research addressing mine fire prevention, early and reliable fire detection, and mine fire suppression technologies. One portion of this program is focused on understanding the characteristics of mine fire combustion products and flame spread through large scale deep-seated (firmly established) fire tests and use of computational fluid dynamics (CFD) modeling. In this study, two deep-seated fire tests were conducted; one fire consisted of coal material and the other utilized the two most abundant fuel sources found in a coal mine: coal and wooden cribbing blocks. The fires were burned to completion while the combustion products were collected and analyzed. In addition, an array of thermocouples was placed within the body of the material to measure flame spread rate. The coal fire test information was then used to develop a CFD model of the fire. This paper describes the fire tests, provides insight into characteristics of flame spread, and presents the CFD modeling work results.

Jan 1, 2009

By O. M. S. Rodrigues

The kaolinite presence in bauxite ores increases caustic soda consumption during the digestion step in the Bayer process. Depending on the kaolinite content, the utilization of the ore in the Bayer process may be unfeasible. This investigation addressed the variables involved in kaolinite flotation through microflotation experiments in a Hallimond tube and zeta potential determinations. The tests were performed with a pure sample of kaolinite (96%). Five collectors were tested: Duomeen T (DT), cetyl pyridinium chloride (CPC), cetyltrimethylammonium bromide (CTAB), dodecylamine (DDA) and Flotigam EDA (EDA). Four of them performed well as collectors, at a concentration of 1x10-4 mol/L: CPC, CTAB, DDA and EDA. The kaolinite isoelectric point (IEP) was determined at pH = 4.6. The IEP was shifted towards higher pH values in the collectors? presence, indicating specific adsorption onto the mineral surface.

Jan 1, 2011

By M. T. Ityokumbul

The effect of reaction conditions on the desulphurization of oil sand coke residues has been studied. The variables investigated were temperature, reaction time, heat transfer resistance, and mode of caustic soda addition. The results obtained show that oil sand coke desulphurization increases with temperature, reaction time, and heat transfer rate. In an oxidative environment, coke combustion during molten caustic leaching (MCL) commences at temperatures above 500°C. The mode of caustic addition has no effect on coke desulphurization.

Jan 1, 1995

By H. Huang, R. N. Gow

"In Part I, Gibbs’ phase rule was applied to mass-balanced EH-pH diagrams for the Cu-As-S-H2O system. The diagrams were generated using the stoichiometry of enargite as a basis. In this study, the calculations were expanded to cover the stoichiometries of three other Cu-As-S minerals – tennantite, sinnerite and lautite – and compared with enargite. Stability regions within the resulting EH-pH diagrams were found to change with stoichiometry such that a particular mineral would predominate if its stoichiometry was used in the calculation. Solution speciation was also found to vary, with thioarsenate being the best example. This stoichiometric effect helps to explain results reported in the literature and would be difficult to realize if it were not for mass-balanced calculations. IntroductionA comprehensive thermodynamic review has been conducted on the aqueous copper-arsenic-sulfur (Cu- As-S) system (Gow et al., 2014, 2015a, 2016b; Gow, Huang and Young, 2016c). Data on the free energies of more than 100 species were collected from various authors, and thermodynamic databases collated to produce mass-balanced EH-pH diagrams using the thermodynamic equilibrium calculation software STABCAL (Huang, 2014). The full database is listed and discussed in Gow et al. (2015a). Diagrams were generated for enargite and confirmed with Raman spectroscopy using bulk mineral electrodes in order to identify reactions spectroelectrochemically. Theoretical calculations agreed well with the experimental results under alkaline conditions (Gow et al., 2015a), acid conditions (Gow et al., 2014) and alkaline sulfide leaching conditions (Gow et al., 2015b).In the present study, additional mass-balanced EH-pH diagrams were generated by changing the Cu-As-S stoichiometry from enargite (Cu3AsS4) to tennantite (Cu12As4S13), sinnerite (Cu6As4S9) and lautite (CuAsS). Regions for the thermodynamically stable species were shown to change with the four different mineral compositions. Potential leach conditions, both for co-dissolution and selective dissolution techniques, were examined for differences in predominant species according to changing copper-to-arsenic ratios, sulfur compositions and sulfur oxidation states."

Jan 1, 2016

By L. H. Munson, E. H. Carbaugh, D. E. Hadlock, L. F. Munson, R. L. Gilchrist

As a result of the Three Mile Accident and because of evidence indicating radiation protection problems, the U.S Nuclear Regulatory Commission (USNRC) undertook a major effort, with the assistance of the Pacific Northwest Laboratory (PNL), to analyze radiation protection programs at 47 commercially operated nuclear power plants. This effort, the health physics appraisal program (HPAP), using a modified management oversite and risk tree analytical logic methodology (MORT) which consisted of analytical trees with applicable questions for each tree, was subsequently extended to include USNRC licensed uranium mills. In the uranium mill appraisal, a team of four senior radiation safety professionals spent a week at each mill evaluating the total health physics program. Prior to the HPAP, the USNRC inspection efforts were designed to determine if the licensees were fulfilling the requirements of the code of federal regulations and the mills source material license. The HPAP, however, was designed and structured to facilitate an integrated look at the total program. It is also directed into areas for which explicit NRC regulatory requirements may not currently exist. The latitude of the HPAP was designed to allow professional judgement in the evaluation of program adequacy, because merely meeting the explicit regulatory requirements does not necessarily ensure an adequate and effective health physics program. The results of the first eight site visits and the generic health physics problems identified within the uranium milling industry will be identified in this paper.

Jan 1, 1981

By I. E. Odom

The rare magnesium-lithium clay mineral hectorite occurs at many places in the McDermitt caldera of Nevada-Oregon. Commercial development of several high purity deposits began in 1986. The hectorite was precipitated in a lake environment formed after collapse of the McDermitt caldera. Hectorite beds and lenses are associated with volcaniclastic sediments, limestones, dolomites, zeolites and locally sandy bentonites. The high purity deposits appear to be associated with hydrothermal areas. The hectorite consists of extremely small flake-shaped crystals, and Ca is the predominant exchangeable ion. Its color ranges from white to light green. Commercial uses developed to date include high brightness magnesium aluminum silicate products, organophilic clays, pulp retention, and ceramics. The MAS is used as a suspending agent, binder, stabilizer and thixotrope in aqueous solutions for cosmetics, household cleaners, pharmaceuticals and miscellaneous industrial applications. Organoclays are used in printing inks and paints.

Jan 1, 1992

By D. C. Yang

A packed column jig has been developed for sharp separation of fine particles--150 down to 1 micron--having different densities. The packed jig is a column filled with corrugated packing. A slurry of mixed particles is fed into the middle of the column. Water enters near the bottom of the column as both a steady state and a pulsating flow. The pulsating water sets up a jigging action that interacts with the packing causing the dense particles to sink and exit the bottom of the jig and the lighter particles to rise and exit the top of the packed jig. The result is a sharp, environmentally friendly, gravity separation machine with low operating costs. Grades and recoveries of iron ore exceed that of known devices. Grades as high as 95 percent purity with concomitantly high recoveries are common for iron ore concentration. Low silica, sulfur and phosphate are common. This paper is the first to unveil the packed column jig technology in detail and presents its physical model with performance data. The purification of iron ores and coal is the paper's focus.

Jan 1, 1997

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By A. Khan

The effect of sulfur dioxide on collectorless and collector induced flotation of chalcopyrite was studied by cyclic voltammetry on a rotating disc electrode. Contact angle measurements were made to determine the effect of sulfur dioxide concentration and electrochemical treatment. The benefits of sulfur dioxide in enhancing the selectivity of separating chalcopyrite from complex sulfide ores are discussed.

Jan 1, 1996

By Otis M. Clarke

The purpose of geochemical research in the Alabama copper belt is to re-evaluate geochemical prospecting methods as related to igneous and metamorphic rocks in a humid climate. It is also a correlation of laboratory research on copper mineral solubility with geochemical anomalies over known mineral deposits. Geochemical prospecting in warm humid climates involves different problems and conditions than geochemical prospecting in semiarid areas. Stems and others (1972) reported soil surveys in a humid tropical environment in Bahia, Brazil, were not effective in outlining areas of copper mineralization. Clarke (1971) reported false anomalies in lateritic soils in Alabama over mafic rocks. Bjorklund (1971) reported biogeochemical sampling in Finland was ineffective in detailed work outlining potential mineralized areas, although it may serve to indicate regional areas of high mineral potential. During this investigation, water, stream sediments, residual soil, and organic matter, mainly twigs, were collected from three known copper-mineralized areas. Samples were selected so as to cross mineralized outcrops and results were correlated with copper stability charts as reported by Silman (1958) and Schmitt (1962). The geochemical research performed in Alabama should be applicable to other humid areas. Geologic, Climatic, and Pedologic Setting The area of investigation is in the southern end of the Appalachian eugosyncline in eastern Alabama. It includes the Hatchet Creek prospect, Pyriton mining district, and Stone Hill copper mine. The copper mineralization is in calcium-rich metasediments that lie along the western flank of a high rank metamorphic belt. All three deposits are in the uplands of the Ashland Plateau section of the Piedmont physiographic province. The Hatchet Creek copper prospect (Clarke, 1963; 1971) consists of three mineralized areas that contain pyrrhotite, pyrite, and chalcopyrite in small crisscrossing veinlets.

Jan 1, 1972

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

The latest resource estimate for the Caspiche gold/silver/copper project in the Maricunga region of Chile was released by gold explorer Exeter Resource Corp. The resource is low grade, but bulk minable and drilling to date has shown a NI 43-101 compliant inferred resource of 1,117 Mt (1.23 billion st) grading 0.55 g/t (0.016 oz/st) gold, 3.81 g/t (0.111 oz/st) silver and 0.22 percent copper. Exeter said these findings make the in situ metals amounts of 609 t (19.6 million oz) of gold, 4.4 kt (137 million oz) of silver and 4.84 billion lbs of copper, which the company relates as 33.7 million gold equivalent ounces using assumed metal prices of $23.33/g ($800/oz) for gold, 35 cents/g ($12/oz) for silver and $2/lb for copper. The deposit is almost midway between Barrick?s Cerro Casale gold deposit and Kinross? Refugio Mine. In a statement Exeter chairman Yale Simpson said ?This updated resource estimate places Caspiche firmly among the world?s largest gold-copper discoveries in recent years and clearly supports our decision to aggressively drill the property, despite the global economic decline. ?We expect that the very substantial copper and silver credits will be extremely important, and will markedly impact the potential viability of Caspiche. Specifically, using metal prices of US$2/lb copper, $23.33/g ($800/oz) gold and 35 cents/g ($12/oz) silver, the 4.84 billion lbs of copper and 4.2 kt (137 million oz) of silver are equivalent to 376 kt and 62 t (12.1 and 2 million oz) of gold, respectively. ?Our recent drilling has defined what appears to be a coherent higher grade central zone associated with a definable early stage diorite intrusion. We expect this zone will be important in developing various mining and economic models for the project,? Simpson said. Exeter is still drilling the deposit to expand the re-source estimate further to the southeast and at depth and to upgrade the higher grade central zone to the indicated category. Simpson said, ?Exeter intends to enhance the value of Caspiche by continuing to de-risk the project through ongoing exploration, metallurgy, engineering, water and environmental studies. These studies will continue through the next 12 months and will lead to a conceptual development study. A timeline for the release of that study is being formulated. The project budget for the next 12 months is C$14 million.? Mineweb reported that Caspiche is likely too big of a deposit and at too high of altitude for Exeter to handle alone. Exeter will be looking to other majors, or perhaps the Chinese, to help develop this huge orebody. But, in the meantime, it also has its high grade Cerro Moro deposit in Argentina, which could be brought to production relatively quickly and at relatively low cost.

Jan 1, 2009

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities, or 82 percent, may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible.

Jan 1, 2016

By P. M. Hawley

Kennecott Corporation, in joint venture with Galactic Resources Ltd., recently began operation of an open pit gold mining and milling facility near Columbia, South Carolina. The deposit consists of two ore bodies (North and South deposits) hosted in deformed and altered meta-volcanics and meta-sediments of the Carolina Slate Belt. This paper describes the rock mechanics and engineering geology investigations conducted for design of interim, ultimate and final reclamation slopes for the South Pit. Emphasis includes the successful use of drill core orientation techniques to confirm complex geologic structure at depth; the development of a three-dimensional rock mass competency model, incorporating surface mapping data, results of bench mapping documentation, field index testing and laboratory testing; and kinematic assessments for design of optimum slopes.

Jan 1, 1991