Search Documents

By Daniel E. Walsh

A pilot scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2"), crushed ore from Ester Dome, Alaska. 9.04 tonnes (9.94 tons) of crushed ore were sampled and processed through a Pan-American jig -Wifley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/tonne (22.4 oz/ton). The feed grade to the plant was calculated at 1.71 g/tonne (0.050z/ton). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/tonne (0.042), 1.30 g/tonne (0.038), and 5.47 g/tonne (0.16 oz/ton) respectively. Significant, coarse, free milling gold values were shown to remain in the jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1991

By Y. C. Kim

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that Ordinary Kriging (OK) cannot easily handle. With the recent introduction of the nonparametric, distribution-free technique of Indicator Kriging (IK), the above problems can be solved. This paper describes the results of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blast hole information. The IK estimator, although a bit optimistic, performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion. OK was found to be very biased and pessimistic.

Jan 1, 1986

By Thomas E. Finch

Coal produced from surface mines in the Western United States is becoming a more important part of this nation's economy as other types of fuels become scarce. This paper reports the investigation of alternative methods of handling the parting between two coal seams. The results of this investigation are presented as the engineering-economic aspects of alternative parting handling methods involving stowing or back filling techniques. The coal and parting characteristics were selected as being representative of those under consideration or actively mined in the West. The basic philosophy of evaluation is to establish a mine-within-a-mine where equipment selected for minimal capital investment can remove the parting and second seam nearly independent of the ongoing, present production. With proper consideration of design, this parting-coal removal is evaluated as a second operation within the first and has its own profitability measure. The Fort Union Area of Montana, Wyoming, and the Dakotas contains large reserves of low sulfur sub-bituminous coal. In many locations, several coal seams are close to the surface and are separated by relatively thin layers of parting. The removal of overburden and the mining of the upper seam is accomplished effectively with conventional mining methods and equipment. Mining a second seam of coal and handling the parting in accord with economic and environmental controls presents a number of problems. Typically, mining companies have adapted the conventional strip mining techniques used in the East. However, the extreme thickness of the western coal seams offers alternative mining method possibilities for parting and second seam removal.

Jan 1, 1976

By H. Maleki

This paper recognizes the 100th year of research accomplishments by the mining industry resulting from close cooperation among mining companies, geotechnical consultants and researchers from the former United States Bureau of Mines in stability assessments and development of improved and productive mine designs. The paper provides an overview of dramatic developments in geotechnical instrumentation, and its applications in the U.S. and around the world for enhancing the understanding of ground response to mining-induced changes in stress, resulting in improvements in ground control technologies.

Jan 1, 2010

By Jack V. Hill

A unique type of grinding mill liner has been developed by Waagner-Biro A.G. of Austria. This liner system, termed an angular spiral lining (.ESL), was, successfully tested by Magma Copper Company's San Manuel concentrator in both their 10 Ft x 10 Ft (3.05m x 3.05m) and 12 Ft, 6 In x 14 Ft (3.81m x 4.27m) grate discharge wet grinding ball mills. Magma Copper's savings in power and grinding balls justified conversion of more than half of their twenty-six ball mills to the ESL system.1,2 The ASL system was provided by the Capitol Castings Division of Midland Ross Corporation, the exclusive licensee for such conversions. Capitol Castings proposed the following as expected benefits from installation of an ASL system in an 18 Ft x 21 Ft (5.49m x 6.40m) overflow discharge wet grinding ball mill at the Pinto Valley Operation of Cities Service Company: "(a) Reduction of power consumption per ton of ore milled = 12%, (b) Increased throughput = 6%, (c) Reduction of ball consumption = 6%."

Jan 1, 1982

By James L. Withiam, P. C. Kelsall

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

By R. A. Seitz

Although the role of the collector has long been thought to play a predominant role in coal flotation, recent investigations by the authors show that the frother plays an equally important role. These investigations have included extensive testwork in several coal preparation plants and in the laboratory. The factors which were investigated include the absolute level of collector and frother addition, the ratio of frother to collector additions, the type of frother, and the particle size distribution of the feed. Results from this testwork reveal strong interactions between these factors as well as the necessity of considering these factors in order to optimize the reagent regime.

Jan 1, 1987

By David H. Carlson

Mechanical sorting of "poor" rock accumulated from past native copper mining operations has been under study at the Michigan Tech's Institute of Mineral Research for several years. Prior to this work, the poor rock dumps totaling approximately 9 million tons containing an estimated 35-70 million pounds of copper (1) have been considered mainly as a local source of road aggregate used from time to time and consequently of minor value. An electro¬mechanical sorting machine developed by International Sorting Systems Corporation of Santa Barbara, California has been tested for preconcentration of the waste rock before conventional milling (2,3). The ISSC machine has possibilities for underground preconcentration of crushed mine-run native copper ores. The objective of the study described here was to provide information about limi¬tations on sortability due to characteristics of the ore and present crushing practices. When the native copper mines were in operation prior to termination in 1969, two types of ore were produced, amygdaloidal and conglomeritic. In the first type copper occurs in vesicles left by gas bubbles entrapped during rapid cooling of the tops of lava flows. The conglomeritic ore beds consist of rounded pebbles and fragments cemented together by calcite, epidote, chlorite, and feldspar; the copper occurs around pebbles, in cracks, and sometimes as partial or total re¬placements of pebbles. The copper in the conglomeritic ore usually is in finer grain sizes than that in the amygdaloidal ore, and large (plus 4 inch) copper masses are virtually absent.

Jan 1, 1970

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By Steven Hoerger

Mixed integer linear programming (MILP) production scheduling models can be used to evaluate if tonnage improvement projects will deliver value over all time periods and whether new bottlenecks will be created. These MILP models can evaluate the interconnected effects of mine and process capacities, mining locations, cutoff grades, stockpiles, and orebody grade/tonnage distributions. A case study compares potential value creation from a mine capacity increase, a mill capacity increase, or a simultaneous increase in all capacities. For perspective, project valuations for capacity increases are compared against valuations for cost reduction projects, mine planning improvements such as phase design, dynamic cutoff grades and stockpiling, and the impact of geostatistics improvements in the areas of block model accuracy and ore control selectivity.

Feb 1, 2024

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By Paul C. Lingo

Two recent antitrust cases, coming from widely separated areas, different industries and involving wholly different facts were decided by the Supreme Court on June 7, 1965. The decisions in there two cases may well prove to be the most important and far-reaching decisions in the field of labor law that have been handed down in the last 24 years. These cases, although quite dissimilar factually, had one common element. In both, the gravamen of the antitrust violation was bottomed on the terms of labor agreements negotiated by a multiemployer group. These cases are usually referred to as Pennington1 and Jewel Teat. Since a number of references will be made to the antitrust laws, it may be well to state briefly the applicable portions. Section 1 of the Sherman Antitrust Act makes "every contract, combination in the form of trust or otherwise, or conspiracy, in restraint of trade or commerce among the several states, or with foreign nations, is declared to be illegal...". Section 2 imposes criminal sanctions against "Every person who shall monopolize, or attempt to monopolize, or combine or conspire with any other person or persons, to monopolize any part of the trade or commerce among the several states...". Under Section 4 of the Clayton Act a person who sustains damages as a result of a violation of the anti¬trust laws is entitled to recover treble damages plus costs.

Jan 1, 1966

By Dolf W. Fieldman

Most recently the geologic setting of the mineral deposits in the Silver Cliff district is described by William M. Sharp in ?Geologic Map of the Silver Cliff and Rosita Volcanic Centers, Custer County, Colorado?, (U. S. G. S. Map I- 1081). The discussion will relate only to the southern half of the Silver Cliff volcanic center and differences in geologic interpretation, which are largely structural, will be pointed out as they arise. Only the manganese/silver zone of the Kate Area will be discussed in detail.

Jan 1, 1980

By B. Denby

Recent advances in Virtual Reality (VR) technology have resulted in major opportunities to improve safety training of mine workers, supervisors and managers. The hazardous nature of both surface and underground environments limits the type of safety training that can be carried out. VR offers the potential to expose mine personnel to hazardous situations in a safe, highly visual and interactive manner. Customized simulations of mine layouts, dynamic operations and mine environment can be set up and mine personnel can be allowed to move around the virtual mine, making decisions at key points. The consequences of both correct and incorrect decisions can be immediately fed back to the trainee.

Jan 1, 1998

By Eva K. Fernandez, Paul Y. Louie, Derek S. Adams, Renée L. Fippin

The Folsom Area Stormwater Improvement Project is part of SFPUC’s flood resilience efforts under the Sewer System Improvement Program. This 4,000-foot-long, 12-footinside- diameter tunnel will help reduce the risk of flooding in San Francisco’s low-lying Inner Mission neighborhood. The project is in a high seismic hazard zone and extends through a complex geologic corridor that includes full-face soft, compressible Bay Mud, Colma Sands, and full-face rock with several stretches of mixed-face conditions. Additional challenges include removal of 99 piles beneath an existing box sewer, tunneling under commuter rail tracks, and an underground tie-in. This paper examines these challenges and how they are being addressed.

Jun 13, 2023

By J. P. Ducarme, J. L. Carr, C. C. Jobes

"An average of 1.2 fatalities occur per year in underground coal mines in the United States when a miner is struck or pinned by a remote-controlled continuous mining machine. Proximity detection technology provides a means to prevent these types of accidents by disabling all machine motion when a miner is in close proximity. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed the intelligent Proximity Detection (iPD) system, which continuously tracks the position of miners near the machine and disables only those machine motions that could cause a pinning accident. This system, previously demonstrated using non-permissible proximity detection hardware, has now been shown to be effective when implemented using an MSHA-approved system as a platform. Performance tests have shown accuracy, repeatability, and stop zone identification to be comparable to or better than the system demonstrated with non-permissible hardware. INTRODUCTION Underground coal mining room-and-pillar operations typically use Continuous Mining Machines (CMMs), such as the one shown in Figure 1. When CMMs first became available, they were operated from an on-board operator’s compartment that protected operators from roof falls and other hazards but severely restricted visibility and subjected them to machine vibration and high levels of dust and noise. To solve these problems, remote controls were developed to operate CMMs. Now CMM operators are free to position themselves for best visibility of each mining task and are no longer subjected to the rough motion of the CMM during mining operations or the dust and noise generated by the machine. However, this technological advance removed operators from the protection afforded by the operator’s compartment and exposed them to the hazard of being struck or pinned by the CMM or other large moving machines."

Jan 1, 2015

By P. Eger

In 1991, LTV Steel Mining Company decided to close an open pit taconite mine in northeastern Minnesota, using a passive treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. Over 50 million metric tons of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages, and prior to closure annual median concentrations ranged from 1.5-50 mg/L. Copper, cobalt and zinc are also present but are generally less than 5% of the nickel values. Median pH ranges from 5.0 to 7.5, but most of the stockpile drainages have pH greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential a stockpile had to produce acid drainage, the lower the permeability of the capping material required. Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to over 90% for the plastic liner. Five constructed wetlands have been installed since 1992, and have removed 60-90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Since mine drainage problems can continue for over a hundred years, the lower annual operating costs should pay for the construction of the wetland treatment systems within seven years.

Jan 1, 1999

By Manuel Viveros J.

This paper will deal with the type of rocks so called evaporites, which are sedimentary rocks produced by water evaporation from seas, lakes or marginal lagoons, in warm and arid climates. Salts derived from these deposits are precipitated according to their solubility; that is, the more soluble precipitates first, overlain by other sediments like silts, shales, limestones, sands, etc. The most common evaporites, according to their chemical composition, are : Chlorides Sulphates Carbonates Nitrates Borates Common salt, or halite, sulphates like anhydrite and gypsum, are the most important. Potassium chloride (silvite and carnalite) and potassium sulphate are of great commercial value.

Jan 1, 1974

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972