Search Documents

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By Frank W. Pereira

The Montana Talc ore body was discovered in 1983 in Montana's Gravelly Range, about 40 km (25 miles) south of Ennis. Initial drilling indicated a 910-kt (1-million st) ore body of high purity talc. Preliminary analyses on ore cuttings included chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. Results indicated it was similar to talc currently being marketed from Montana and it would probably have good commercial value. Based on the positive test results, a test pit was made and a 180-t (200-st) sample of ore was mined. A portion of the ore was ground to various particle sizes and evaluated to determine its strengths, weaknesses, and other characteristics. The deposit is located close to the Cyprus Yellowstone deposit. It was therefore believed that Montana Talc ore may possess many of the same characteristics. Testing and analyses showed the talc to have a high purity and an extremely large surface area, even for Montanatype tales. The ore was also situated in a massive deposit, indicating low cost mining. While the lab analyses were encouraging, the true evidence would be obtained from commercial tests in the marketplace. About 91 t (100 st) of ore were ground to product specifications for pitch control, paint filler, and plastics filler. Consumers were contacted and requested to evaluate the sample talc products. A major trial for the talc as a pitch control agent was arranged at a Northeast paper mill. The trial indicated the new Montana Talc product performed as well or better than the current standard in the industry. In fact, due to a minor modification in the compaction process to make the transport of the talc easier, the product had substantially less dust than the currently used product. The operating people at the paper mill requested that management purchase this talc. Trials were also run at paint plants for use as a pigment filler. And the talc was fabricated into a number of plastics compounds. The initial product tests were largely positive and provided encouragement to proceed with the project. Different grinding mills were used and their performance evaluated. Significant data were generated by the custom grinders. They indicated how the Montana Talc ore ground and the particle size distributions produced at different grinding settings. Encouraged by the positive marketing tests, a prefeasibility study was commissioned. A talc grinding plant and mine plans were designed and capital and operating costs estimated. Initial economics showed an attractive return. The operating costs were among the lowest in the industry. The positive economics, along with the excellent results by the products in the marketing tests to the paper, paint, and plastics industries, led to the recommendation to proceed with the project. Plant construction began in June of 1985. The Montana Talc Co. (MTC) analyzed the data from the commercial tests. Based on the product's outstanding performance and the uniqueness of its high purity and platy structure, a strategy was developed to position the company as a premium talc supplier.

Jan 1, 1989

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By A. D. Davis

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well defined drainage in a heavily mineralized area of the northern Black Hills. The basin contains numerous inactive and abandoned mines as well as a currently active heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer and thus can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted, and two abandoned mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 1997

By Terry A. Rightnour

Multiple seam mining is predominant throughout the central Pennsylvania Appalachian coal fields. Wide ranges in individual seam thickness, coal quality, and overburden characteristics are common throughout the region. On typical mining permits, ranging from 404 x 103 to 2023 x 103 m2 (100 to 500 acres), often as many as eight seams are concurrently mined, with each interburden requiring unique economic and environmental consideration in the mine plan. Specifically, this paper presents several planning tools and operational guidelines developed in response to current regulations for the special handling of potentially acid-forming materials as they are related to development and operation of multiple seam mines.

Jan 1, 1984

By J. B. Webster

Health and Safety in the work place is of primary concern to the underground coal industry. Control of dust in the underground environment is of major importance in this concern. Utah Power and Light Mining Division has undertaken extensive studies to determine and control the various sources of respirable dust in underground high production sections. Determination of dust sources has been achieved by real-time aerosol sampling and standard gravimetric sampling on individuals and in various suspect locations. Some sources are diesel roadway dust, outby crushing, and handling equipment, face sloughing, water spray roll-back, and mining equipment. Once identified, the dust sources are suppressed or controlled and/or the workers are directed from areas of greatest potential exposure.

Jan 1, 1990

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968

By W. M. Luff

The Brunswick No. 12 Deposit is a large polymetallic massive sulphide deposit, occurring in Ordovician age rocks of the Tetagouche Group. Silver is contained within the sulphide zones and economically it is the second most important commodity produced. Brunswick is one of the largest silver producers in Canada. The distribution of silver within the mine is presented, with examples from various levels. The concentration of silver can be shown to be related to both stratigraphy and structure. The mineralogy of silver in mill products is also presented.

Jan 1, 1986

By K. W. Vincent

This paper, deals with the beneficiation of a low grade Western phosphate to ore. More specifically it summarizes the results of a study made to optimize a scrubbing step in the process, and to provide firmer data for use in plant design. The deposit is situated about 30 miles northeast of Pocatello, Idaho, in the Fort Hall Indian Reservation. It is a bedded deposit and throughout most o the orebody includes three contiguous layers of phosphatic material which differ in P205 content. The J. R. Simplot Company, as operator for a Simplot-FMC joint venture, mines the ore selectively by open pit methods The lower bed containing a nominal 30% P205 is shipped to the Simplot Company fertilizer complex near Pocatello; the middle layer averaging about 24% P205 supplies the FMC elemental phosphorus plant also near Pocatello, The top layer averaging around 16% P205 and designated as mill grade shale is stockpiled for future beneficiation. This paper is concerned with some aspects of the processing of this low grade shale.

Jan 1, 1965

By A. Toulet

Mining in Mexico has an immensely long tradition. In his first letter reporting to his sovereigns from Mexico in July 1519, Hernan Cortes wrote, "To our mind it is probable that this land contains as many riches as that from which Solomon is said to have obtained the gold for the temple ... " 1 But not only precious metals drew his attention; in 1524, short of tin needed for casting guns, he found it in Taxco. As an added bonus, those who went to find it "came upon a vein of iron which according to experts is of exceeding richness." 2 Since then, the mines of Mexico have yielded up enormous amounts of mineral and continue to do so. Mexico is one of the ten principal producers of minerals world-wide both in production volume and diversity. 3 Tens of thousands of tons of iron, sulphur, and coal come from its earth annually; it is the world's second largest producer of barite; third of antimony, fluorite, and graphite. 4 Copper, zinc, silver, molybdenum, arsenic and cadmium and others are wrested from its mines. The wealth is there; but maximizing its potential requires investment, technology, and markets that the government cannot itself provide. Thus mining, since the Mexican Revolution severely restricted by both law and policy, today looks to private investment to develop its potential. Beginning in 1989, Mexico's government cautiously moved to liberalize private sector involvement in mining; 5 using the experience gained from these initial regulatory changes, the current new Mining Law was adopted in 1992 6 and new Regulations were promulgated in 1993. 7

Jan 1, 1994

By John P. Mahaffey

Thank you Mr. Chairman, Ladies and Gentlemen of SME-AIM? for this opportunity to talk to you about, one of the most interesting and challenging facets of our mining industry. Because the need was then -we built in 1964 what is still today, one of the most sophisticated AC mining machine simulators for this or any industry. It simulated the electrical controls and circuits of an AC shuttle car. The student activated the controls on the main console, which represented the elementary control and power circuits. Its accompanying slide-tape program, student manual and worksheets provided our customers with an effective and highly motivational means to teach their face mechanics: 1. practical AC circuit and motor theory 2. print reading 3. troubleshooting techniques Nearly 10,000 men have put in over 100,000 manhours of training on the AC panel and its DC counterpart. The DC panel was modeled after the 14BU10 Loader. The success of these larger panels pointed out the need in our industry for an orangized, basic electrical program designed around mining machinery components & circuits. But probably more importantly, they brought to light the tremendous thirst for upgrading by our industry's employees. We then turned our attention to developing programs around very basic panels. The resulting programs were designed also to assure maximum student involvement.

Jan 1, 1975

By C. L. Schneider, R. P. King

The ability to predict the liberation spectra that will be produced by a closed-continuous grinding circuit is of fundamental importance for the design, optimization and control of most operations in an ore dressing plant. The only known approach through which such a calculation can be performed is the population-balance-model equation. The latest, and certainly most significant, advance made in this area is the solution proposed by King (1990), which requires one textural parameter measured directly from the ore being studied. The main advantage of King's solution is that, unlike the conventional solutions, it does not require the estimation of hundreds of arbitrary parameters that cannot be independently measured. However, King's solution relies heavily on a knowledge of the detailed internal structure of the Andrews-Mika diagram (Andrews and Mika, 1975), which has never been measured for any ore. The characterization of the internal structure if the Andrews-Mika diagram requires the measurement of the liberation spectra at several progeny sizes produced by the breakage of monosize-monograde particles at several different grades. In this paper, a procedure based on magnetic fluid fractionation for generating seven narrow-size, narrow-grade samples is presented. Each of these samples was then broken into six progeny size classes in an ultrasonic mill. The one- dimensional liberation spectra of each of the 42 progeny and seven parent particle samples were then measured by image analysis. The measured linear-grade distributions are presented in this paper. The calculation of the correspondent volumetric-grade distributions is discussed.

Jan 1, 1995

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982

By M. J. Virnig, G. A. Kordosky

Throughout time, the mining industry has been very successful in meeting the world's requirements for metals and materials while meeting the challenges of decreasing ore grades and increased emphasis on protection of the environment. This success has been due to the development and implementation of new technologies. A clear example of such a development over the past 25 years is the increasing use of leaching/solvent extraction/electrowinning for the recovery of copper from oxide and sulfide ores. The key to the successful introduction of this technology was the discovery and development of the hydroxyoxime liquid ion exchange reagents by General Mills Chemicals (now Henkel Corporation). An important role was also played by the close working relationships between General Mills Chemicals and Ranchers Exploration which resulted in startup of the first plant in 1968 and between General Mills Chemicals and Bagdad Copper which resulted in the startup of the second copper SX-EW plant in August of 1970. Following on the heels of the hydroxyoxime development came the commercialization of other new chelating reagents based on different chemical functionalities, i.e., beta-diketones, alkylated 8- hydroxyquinolines and sulfonamidoquinolines. This initial spurt of activity was then followed by a slowing of development in terms of new reagent functionalities. Activity has continued in terms of further optimization/improvement of existing reagent functionalities but the commercialization of new reagent functionalities has slackened. This observation reflects the fact that the development of new reagent functionalities for metal recovery has become increasingly more expensive such that the right combination of price and sales volume must exist in order to justify the investment required to bring a new reagent to the market place. Given the dependence of the mining industry on innovation to meet the needs of the future, one can ask how these new developments, particularly in new reagents, will occur. To arrive at an estimate of the costs involved in commercializing a new metal extractant functionality, particularly a chelating type functionality, a case study of the development of LIX ®* 34

Jan 1, 1994

By Sean Hunter

Artificial Intelligence has a long history but is currently coming strongly into focus with new advancements. This leads to questions many people are asking: what exactly is AI, how can it be used effectively in mining operations, and what foundation is required to make AI implementations successful? In mining, many AI applications exist, from drill pattern optimization to predictive maintenance. However, many implementations struggle due to data integration challenges. Mining operations generate large amounts of data from many sources, such as fleet management systems, drill sensors, process control systems, and laboratory results. Unfortunately, this data often exists in silos where it’s difficult to get it out, making AI applications unable to leverage it. Worse still, tools that use AI don’t always provide their data back to the system, creating even further data silos. All these problems make it hard to take advantage of the data at the mine, slowing down and reducing the effectiveness of AI. This paper presents a comprehensive approach to organizing mining data using an AI-ready knowledge graph system. We will first explore the evolution of AI in mining, from early expert systems to modern machine learning applications. Then, we will detail how a knowledge graph can integrate business context, operational data, and AI models into a cohesive system that enables more effective AI implementations across mining operations. The proposed method has been developed considering both the unique data challenges faced by the mining industry, while also considering best practices learned from the AI field at large. By following this approach, it’s possible to better utilize existing data, getting higher quality and more complete results faster, and in a way that’s reusable and composable.

Feb 1, 2025

By F. Grajales Munoz

The Cienega project, now under construction by Penoles group, is located in the mountains of the State of Durango, Mexico. The gold and silver deposits are found in the 4-km long system of veins, which will be extracted by underground methods. The planned 1000 tpd process plant will contain a countercurrent cyanide circuit for oxide ore and a flotation circuit for sulfide ore. Considerable resources have been devoted to development of infrastructure in the isolated location, as well as for the mitigation of environmental impacts. Startup is scheduled for the third quarter of 1994.

Jan 1, 1994

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By J. R. Nawrot

Reclamation of potentially acid producing coal processing waste requires a 4-foot cover, and/or treatment to allow vegetation establishment. If not planned properly, soil covering alone does not prevent refuse acidification or formation of acid seeps. Adequate neutralization enhancement prior to soil covering can maintain an alkaline environment in the soil refuse interface and prevent acidification. Direct vegetation establishment using only limestone amendment (without soil cover) can successfully reclaim aged and weathered fine (Blurry) and coarse (gob) refuse if adequate neutralization treatment is provided for the oxidized surface zone. Acid seeps, representing an "after-the-fact" verification of an imbalance of acid-base equilibrium may also be corrected using upslope alkaline recharge techniques. Concentrated alkaline recharge pools have been constructed above previously soil covered acid gob at the Peabody Will Scarlet Mine to abate acid seeps. Preliminary monitoring results (1989-1992) from a concentrated alkaline recharge pool demonstration project in the Pit 4 area of the Will Scarlet Mine have documented a 50 to 80 percent reduction in acidity in the principal recharge pool groundwater zone. A 22% reduction in acidity has occurred in the primary seeps located downslope from the alkaline recharge pools. The initial improvements in water quality are seen as a positive indication that groundwater acidity will decrease further and amelioration of the acid seep will continue.

Jan 1, 1993

By T. R. Ellis

Considerable movement is afoot internationally to rationalize standards and regulations relating to valuations and the qualifications for valuation professionals. In July 2000 the International Valuation Standards Committee released expanded standards, and additional important improvements are planned by 2003. Possible updates to the International Accounting Standards (IAS) and potential adoption of IAS by the United States could significantly impact minerals appraisers. Standards designed specifically for mineral asset valuation are under development in Canada and the United States, with Australia's internationally respected VALMIN Code providing the benchmark. In the United States, the all-encompassing Uniform Standards of Professional Appraisal Practice (USPAP) is annually modified and continues to gain deeper acceptance, while the SEC holds fast to its 1981 rule prohibiting reporting of a quantitative estimate and value for non-reserve mineralization. Some important international trade agreements are driving actions to free the trade in professional services. In July 2000, an international workshop was held to initiate discussion on minimum qualifications for appraisers to work internationally. Pressure for uniform minimum qualifications and rules for professionals internationally will continue to build. The United States is historically among the slowest countries to implement such initiatives, with its state level licensure barriers having the potential to cause some of its professionals to be stranded in an international backwater. Structural change is needed in Australia's VALMIN Code to remove conflict with the latest International Valuation Standards. The mineral valuation standards developers of Australia, Canada and the United States should work jointly on updating VALMIN for global use.

Jan 1, 2003