Search Documents

By G. Davis

Mineral properties and mineral firms often trade at a market value that is significantly greater than the value indicated by discounted cash flow (DCF) techniques. A possible explanation is that DCF analysis does not consider the value derived from managerial flexibility. Presumably, then, at least some of the difference between DCF value and market value is due to managerial flexibility. This paper surveys the recent attempts to empirically quantify the value of managerial flexibility using option pricing theory. The results indicate that managerial flexibility, at least as measured by the option pricing methodology, falls well short of explaining the gap between DCF value and market value.

Jan 1, 1995

By E. H. Cho

Pittsburgh #8 coal cleaned by the conventional froth flotation was oxidized in a 2-liter Parr Stirred Top Bench Reactor. The oxidation time was varied up to 5 hours; the temperature, from 150 to 225°C, the oxygen pressure, from 15 to 500 psi; and coal dosage, from 15 to 60 grams in 600 ml of distilled water. The oxidation of coal was evaluated by measuring total acidic group formed on the coal surface as well as by measuring the adsorption of calcium ion from a solution under standard conditions. It was found that the oxidation increased with increasing oxygen pressure without much leveling-off effect. However, the oxidation of coal increased sharply from 150°C to 175°C and then tended to level off above 175°C. The adsorption of calcium was reached more than 3% on the coal oxidized under favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The BTU loss was sensitive to oxidation temperature. This study concludes that the optimum oxidation of coal should be conducted at high oxygen pressures around (e.g. 500 psi) 170°C for 3 hours. This study also concludes that the oxidation in an autoclave is far superior to that in a fluidized bed in terms of calcium adsorption, BTU loss and reaction time.

Jan 1, 1994

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By Patrick Sullivan

Over the past few years, successful operations for processing phosphates employing the Grate-Kiln System have been achieved. Control and instrumentation philosophy followed in these installations are described and analyzed. Concepts utilizing digital techniques and computer systems appropriate for similar installations are also discussed.

Jan 1, 1967

By A. Davis, K. Nelson, C. Webb

Abandoned mines in parts of the Black Hills of South Dakota have the potential for acid rock drainage. For this work, ten sites were examined on Black Hills National Forest land or on private land whose drainage could affect Forest Service land. Water samples from all the sites had pH values less than 6. Results of analyses from water samples and rock samples showed a correlation between metals content and pH. Acid-base accounting was used to determine acid drainage potential of the sites. One site (King of the West Mine) had a high potential for acid generation; fortunately, little or no surface runoff leaves the mine site. Six sites appeared to have moderate potential, including the Minnesota Ridge Mine, which currently is being remediated. Three of the sites had low acid drainage potential.

Jan 1, 2004

By X. Wu

A quantitative damage evaluation caused by ground motions associated with strong roof caving is presented. The strong roofs are modeled as either cantilevering or bridging beams over continuous elastic foundations subject to an exponentially distributed vertical stress. Major factors influencing roof caveability and strain energy buildup are identified and investigated. A methodology to evaluate the strain energy accumulation caused by overhanging roof is presented. The potential for mine tremors is determined in terms of the local Richter magnitude ML which depends on the seismic energy transformed from the stored strain energy released when the roof fails. A particle velocity model is applied to estimate the damage area associated with roof collapse. A case study from a Utah coal mine shows that estimations of bump severity and damage area agree well with the field observations.

Jan 1, 1995

By G. R. Luster

In most current practice, the methods that are employed in technical evaluations of cement raw materials are deterministic; i.e., decisions among alternative raw mixes and alternative plant designs are reached with the aid of only "average" compositions and "representative" samples of the available raw materials. Nevertheless, cement plants are sensitive to raw-material variability, and uniformly high-quality raw materials are not so abundant as they once were. Some simple examples will illustrate how geological techniques can be combined with geostatistical and operations-research approaches to customize mining and processing systems to deal with variable raw-material compositions.

Jan 1, 1987

By J. E. Shearer

The state of Arizona produced 253,276.2 metric tons (279,000 st) of crude gypsum during 1986. This represents approximately 1.7% of the total U.S. production. Four mines provided Arizona's gypsum, three of these mines are in the San Pedro Valley. The uses of the gypsum produced in Arizona are for manufacture of cement, agricultural uses, and wallboard manufacture. The gypsum is used as a retarder in the manufacture of Portland cement. The use in agriculture is treatment of alkali soils to allow water penetration. Other deposits in the San Pedro Valley have production potential, providing there is sufficient market for additional wallboard. The author completed an evaluation of one property earlier this year.

Jan 1, 1988

By D. B. Sikka

Porphyry type copper ± molybdenum deposits typically occur in the Phanerozoic rocks and have been well documented. During the past two decades a number of porphyry type Cu ± Mo deposits which range in age from 1055 ± 35 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India, Namibia and Zambia. Kalanjkhand porphyry copper deposit M. P., India which is estimated to contain 789 million tonnes averaging 0. 83 percent Cu (millhead-grade); 0.004 percent Mo; 0.2 gm/t Au; 6 gm/t Ag and a cap of 7.532 million tonnes of oxide are averaging 0.8 percent Cu. The economic potential of the expanded copper mining milling, smelting and refining complex to be built in the future at Kalanjkhand, which is the largest porphyry copper deposit discovered to date in the Precambrian rocks of the world is presented.

Jan 1, 1992

By Edwin K. Maughan

The Rocky Mountain region contains part of the paleocontinental shelf that lay in Arizona and New Mexico through Utah, Colorado, and Wyoming into Montana and North Dakota. The shelf was bounded by the northeast-southwest-trending Transcontinental arch and the Cordilleran miogeocline in late Paleozoic and early Mesozoic time. Major tectonic features that affected middle Phanerozoic sediments on the shelf were the Big Snowy trough and Williston basin in the north and the ancestral Rocky Mountains in the central part of the region. The Zuni uplift and similar positive areas occurred along the axis of the Transcontinental arch in the southern part. The late Paleozoic and early Mesozoic sedimentary rocks record transgressive-regressive marine cycles in which the Cordilleran shelf and much of the adjacent craton were inundated by epeiric seas. Early in the Carboniferous, an epeiric sea covered most of the shelf. Greater topographic relief developed in Late Mississippian, was at a maximum in Middle Pennsylvanian, and then diminished through Permian and Triassic time. The development in the Pennsylvanian Period of horsts and grabens along northwest- trending faults on the northwest flank of the Transcontinental arch resulted in the ancestral Rocky Mountain system. The eastern part of the region was emergent by Middle Triassic, and the emergence lasted until Middle Jurassic, owing to uplift along the Transcontinental arch. During the early part of the Mesozoic, the sediments were dominantly terrigenous and were deposited mostly in shallow littoral marine environments shifting to continental. Most middle Phanerozoic structural elements within the area of the shelf are characterized by lineaments that have either an east-northeast or a conjugate north-northwest trend. The east-northeast lineaments closely parallel the northeast trend of the continental slope (miogeocline) in Nevada to southern Idaho. The conjugate set closely parallels the northwesterly continuation of the miogeocline north of an approximately right- angle bend in south-central Idaho. The northeasterly trending Transcontinental arch and the northwest-trending margin of the Canadian Shield are parallel structural elements with the north- east and northwest trends of the miogeocline. The rectangular lineament pattern on the shelf suggests a system of rectilinear fractures within the underlying Precambrian crystalline basement rocks that moved several times in the Phanerozoic in response to external forces applied against the continental crust. Movement of these blocks influenced erosion, deposition, and lithofacies of the sediments in middle Phanerozoic time. Zones of crustal weakness, represented by the lineaments bounding these blocks, probably were influential in localizing sedimentary mineral accumulations and petroleum deposits, as well as later igneous intrusions, volcanism, and emplacement of hydrothermal ores. Igneous activity in this region was rare during the middle Phanerozoic, but these conjugate fractures seem to have been avenues for later passage of hydrothermal solutions responsible for ore emplacement.

Jan 1, 2013

By J. L. Parks

Designs, installation procedures, and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install, and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic 12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.

Jan 1, 1992

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By R. R. Fernández

Newmont Mining Corporation has been processing refractory gold ores by roasting since January 1995. The ores are refractory due to the association of the gold with iron sulfides, namely pyrite and marcasite, and the presence of carbonaceous components and is oxidized in an oxygen-enriched gaseous atmosphere. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent upon the roasting conditions, mainly the roasting temperature. Originally, the sulfides and carbonaceous matter were oxidized at a temperature that typically ranged between 535 and 560 °C. Controlling the roasting temperature within the lower and narrower range of 510 to 515 °C produced a calcine with a larger surface area(e.g. higher porosity), which resulted in a gold recovery increase of3.3 percent in 2001 equivalent to 5.1 million dollars of additional gross revenue. The new strategies of operating at temperatures never tested before are discussed. It constituted a great challenge to the control room operators for the lower operating temperature falls much closer to the ignition temperature of the sulfide ore and smaller and more frequent adjustments in operating parameters were needed to improve and maintain high gold recoveries. Based on the encouraging results that were achieved in 2001, a decision was made to install a “smart” process control system because the roaster temperature control was performed by manual inputs from the control room operators. The development and implementation of the control system to reduce or eliminate the temperature variability between the different control room operators commenced in June of 2002 and was fully operational by the end of October. Lower roaster temperatures were achieved (500 to 505 °C), which resulted in further increase of gold recovery by about two percent. The overall recovery increase equated to 8.0 million dollars of additional revenue for the first 10 months of 2002.

Jan 1, 2003

By A. J. Kwitowski

Teleoperation is a technology that can provide significant health and safety improvements in mining, by relocating machine operators hundreds of meters away from the face area. The U. S. Bureau of Mines (USBM) has recently developed a teleoperation system for continuous mining and haulage equipment. This system features near-real-time closed-loop control. A prototype system was developed and demonstrated on the surface. This system could be used in thin-seam applications down to 914 mm. Details are provided on the developed teleoperation system, results of testing, and expected, future applications of this technology for improved safety.

Jan 1, 1994

By Ataç Başçetin, Hasan Çelt, Hüseyin Onur Dönmez, Kürşat Hasözdemir

Phenolic foams, known for fire resistance, show broader industrial potential, particularly in mining, through property enhancements. Adjustments to the formaldehyde-to-phenol (F/P) ratio, bio-based additives like lignin, and nano-silica improve foam strength and thermal stability. Density modifications allow foams to range from flexible, low-density forms to rigid, high-density supports. In mining, enhanced phenolic foams could reduce coal ignition risks by acting as oxygen-blocking barriers. Current findings suggest these foams offer viable, sustainable solutions for safety in hazardous environments. Continued development could make them essential for thermal and mechanical applications under extreme conditions. This paper aims to provide a comprehensive overview of the mechanical characteristics of phenolic foams, current enhancement strategies, and standardized testing methods used to evaluate foam properties.

Feb 1, 2025

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By P. Moyo, S. Dixon, R. Norcross

The separation and recovery of copper from cyanide solution has been investigated since the early 1900s. The precipitation of copper using sulfide ion was patented in 1911 by Williamson, published by Leaver & Woolf of the USBM in 1931 and Cyanamid in 1960s. The current practice of sulfide precipitation is used in various processes such as “SART" for cyanide regeneration and copper recovery. The precipitation of copper sulfide requires the pH of the clear solution to be in the range of 4-6. The precipitated copper sulfide can be sold to smelters. Alternatively, copper cyanide can be precipitated from clear solutions in the pH range of 2-3. However, selling copper cyanide is challenging because of its cyanide content. Past work has focused on the use of boiling sulfuric acid to convert copper cyanide to copper sulfate as published by Seracini in 1991. This paper describes a simple process to convert copper cyanide to copper oxide using sodium hydroxide at ambient temperatures. The cuprite can be sold to smelters or used as a feed to an electrowinning circuit to produce copper cathodes. The process provides an effective method to recover copper from cyanide solutions with a lower capital requirement.

Mar 2, 2022

By S. H. Amini, A. Noble

"While many classic mineral processing circuit design approaches rely on deterministic methods, numerous studies have shown that the uncertainty inherent to the various input parameters can significantly influence design decisions. In a separation circuit, many of the technical uncertainties can be mathematically represented as statistical distributions for the unit recovery and feed grade. These uncertainties are then propagated by the circuit design and reflected in the circuit performance indicators, such as product grade and global recovery. An effective design strategy entails identifying which units are most influential in this uncertainty propagation and thus merit further consideration. Unfortunately, few analytical tools provide this information, particularly those that rely solely on deterministic methods. However, one promising approach is through the application of Taguchi’s method, in a fashion similar to statistical tolerancing of manufactured products. Since the technical challenges are fundamentally similar, Taguchi’s method shows promise in evaluating the level of compounded uncertainty by various circuit designs while determining the role of each separation stage on the overall selectivity and variability of separation circuits. This paper demonstrates Taguchi’s method in several two and three unit circuit designs. INTRODUCTION AND METHOD DESCRIPTION Uncertainty in Mineral Processing Circuit Design Analysis and estimation of uncertainty propagation in mineral processing separation circuits is an essential and significant aspect of an optimal circuit design procedure. Most of the current circuit design methodologies have been constructed, implemented, and validated using a deterministic modeling approach. However, numerous studies have shown that the inherent uncertainty induced by uncertain design parameters can be a significant factor in many mineral processing applications (e.g. Kraslawski 1989; Xiao and Vien 2003; Ghaffari et al. 2012). Thus, an effective circuit design methodology must be able to quantify uncertainty in separation circuits with limited input data. This paper describes Taguchi’s method, as an experimental design technique, to approximate uncertainty in mineral processing applications, and then the similarity of results between Taguchi’s method and Monte Carlo Simulation is investigated. Monte Carlo Simulation The term “Monte Carlo Simulation” has been used to refer to a variety of stochastic simulation methods spanning a broad array of business, technical, and scientific domains. Most generally, Monte Carlo Simulation refers to numerical analysis which is based on (pseudo) random sampling from a domain of input parameters with a known statistical distribution. This methodology allows one to determine the distribution of expected results from a standard deterministic process model. Execution of a Monte Carlo simulation begins by identifying the domain of input parameters, statistical distributions for each parameter, and a deterministic process model which describes the anticipated result as a function of the inputs. Next, one discrete random sample is taken for each input parameter, considering the input distributions. The process model is then solved for this mix of input parameters, producing a single simulation result. This procedure is then repeated a “large” number of times, utilizing new randomly sampled input parameters for each simulation iteration. Once the desired number of iterations is reached, the results of each independent simulation are aggregated to produce descriptive statistics such as minimum, maximum, mean, standard deviation, kurtosis, and other distribution parameters. Given enough iterations, the Monte Carlo method fully explores potential synergies between the input parameters. The methodology does not require the process model to be differentiable, continuous, or even analytically defined. While the number of required iterations varies in relation to th"

Jan 1, 2017

By Peter B. Dowden, David T. Cass

A shield on a tunneling machine has two basic purposes. Firstly to provide temporary support in unstable ground, maintaining the integrity of the bore and protecting the operators, and secondly, in conjunction with other sealing devices, to prevent the ingress of water. In any specific tunnel, unstable ground and water may or may not occur together. Further, there are a number of different ground behaviors that may be termed unstable and these must be defined in order to determine the most suitable type of machine. Beyond the shield itself, the cutterhead and the mucking system design are critical in successfully traversing difficult geology. In any but the shortest tunnels, variations in the geological conditions and the requirement of an acceptable advance rate can impose increasing degrees of sophistication in the machine design. In this paper we will review current designs of shielded type machines and their application, and discuss new developments which blend hard and soft ground tunneling technology. We will also indicate that in some conditions, although first impressions seem to favor a shielded machine, in fact an open gripper TBM may be the wisest choice.

Jan 1, 1991