Search Documents

By Fumio Wada

Kuroko deposit is a stratabound massive sulphide and sulphate deposit associated with Miocene submarine volcanics and has been considered to be a prototype of meta- morphosed Palaeozoic and Precambrian equivalents. Since the discovery of Uchinotai deposit of the Kosaka mine in 1959, Dowa and other mining companies have conducted intensive exploration work in the Hokuroku district of northeastern Japan. Dowa has been placing its first priority on the exploration of Kuroko deposits and made a series of remarkable successes in finding the Kuroko deposits, i.e. Uchinotai, 1959; Matsumine, 1963; Uwamiki, 1966; Fukazawa, 1969 and Ezuri, 1975. It is emphasized that our successes have resulted from the proper application of exploration technologies accumulated through our experiences. Firstly we defined the Kuroko horizon and favourable felsic volcanism based on the detailed structural and volczno-stratigraphic study of the Hokuroku district, and then delineated the promising areas by means of the quantitative evaluation of geophysical, geochemical and mineralogical parameters such as the magnetic susceptibility and contents of alkaline and alkaline earth metals in the foot wall dacites and clay mineral assemblages of both hanging and foot wall pyroclastics and dacites. Practical application of these techniques is essential to our routine Kuroko exploration.

Jan 1, 1982

By Karin Bäppler

Hydropower produces almost two-thirds of the world’s renewable electricity generation and delivers a major contribution on the ambition of the Paris Agreement and Sustainable Development Goals (SDG) with a range of benefits to society and environment. These include clean and flexible generation and storage in addition to reduced dependence on fossil fuels and avoidance of pollutants. The Limberg III PSP is one of the European projects that addresses the implementation of the UN SDGs. The challenge of the project is the construction of a 770 m long pressure shaft to be excavated with a TBM at an inclination of 42°.

Jun 13, 2023

By E. R. Palowitch

On February 5, 1973, Eastern Associated Coal Corp began shortwall mining in their Federal No. 1 Mine, thus marking the first attempt in the United States at modern shortwall mining, i.e., using a continuous miner to extract coal open-ended from pillars 100 to 200 feet wide, under the protection of a self¬-advancing roof support system (1)1/. Since then, four additional shortwall faces have been operated. While the number of face-years of shortwall experience in the United States is limited, this experience has been anything but uniform. Differences in operator motivation, coalbed parameters, geologic conditions, panel dimensions, and face equipment all have contributed to a wealth of knowledge which can provide guidance for the design of future shortwalls. The purpose of this paper is to review the history of shortwall mining in the United States and to assess its value to the U.S. coal industry in terms of the health and safety of the miner, the percentage of coal recovered, coal production, worker productivity, and relative cost performance.

Jan 1, 1976

By K. P. Chong

Fracture toughness of oil shale is an essential property in fragmentation to optimize particle sizes and permeability distributions in in-situ processes. Fracture mechanics of oil shale has been based on conventional fracture mechanics using notched samples and assuming the material to be isotropic and elastic. Oil shale is a layered material more accurately characterized as transversely isotropic. The senior author proposes to use a semi- circular core specimen with a center crack subjected to three point bending. Singular crack tip elements with isoparametric elements are used. The precracked semi-circular disk is modeled under displacement loading. The effect of crack length on the non-dimensionalized stress intensity factor is investigated by strain energy method, ellipse method, and stress method. Very close agreements are found. The fracture toughness is obtained by compressing the specimen in to failure. Parameters such as oil yield are investigated.

Jan 1, 1984

By F. J. Susko

The U.S. Bureau of Mines is using Fourier-transform infrared (FT-IR) analysis to investigate the bonding mechanism which occurs during the dewatering of clay slurries. High molecular weight polymers are used as flocculating agents in these processes. This investigation presents the results of an FT-IR study of calcium-exchanged montmorillonite treated with polyacrylamide (PAM) and polyethylene oxide (PEO). Both thin film and attenuated total reflectance (ATR) spectroscopic techniques were employed to study this clay-polymer system~ Results suggest PAM is adsorbed to the clay via the nitrogen atom of the polymer. A water bridge is involved in the bonding between the clay and PE~. Evidence also suggests that PEO may be adsorbed directly onto the surface of the clay.

Jan 1, 1990

By H. R. Coles

Test work conducted in the 6.4 and 10.52 m Aerofall Mills at the Iron Ore Company of Canada Carol Project showed that the conventionally used ?deflector?-type liners which form the basic principle of Aerofall Mill grinding did not necessarily provide the best grinding performance. A new design, using low profile liners incorporating radial ribs of a proper height, actually improved the mill throughput in the order of 9 to 20% without sacrificing grinding efficiency. In addition, the new design reduced liner weight and scrap losses, which resulted in a reduction of liner consumption by 25%. It provided better protection to the mill shell and reduced the overall maintenance cost for the mill

Jan 1, 1980

By N. P. Reddy

This paper describes an experimental setup for multiple-fan ventilation systems at the ventilation laboratory of the WVU Department of Mining Engineering. Housed in a 30 ft by 70 ft room, the experimental setup consists of three 18 in. variable-speed axial-flow fans, the 18 in. diameter fiberglass tubing and fittings for arranging networks, and the pitot tube measuring and data acquisition system. The fiberglass tubing and fans can be organized into the non-planner network of two fans or three-fans. It is mainly designed for studying the characteristic curves, operating points, and fan stall for the multiple-fan ventilation system.

Jan 1, 1992

By Gy. Deák Deák

The ECOMINING platform aims to develop a scientific and technical organization in order to promote within the natural resources industry a framework for environment-friendly exploitation technologies (on Best Available Technologies principle) and also to develop a solid basis for performing Research and Development projects. The ground of this project is the success of the First International Seminar: ECOMIN-ING - Europe in 21st Century1, organized by the Research and Development National Institute for Metals and Radioactive Resources Bucharest in co-operation with ITASCA Consultants GmbH Germany, the University of Petrosani and supported by the National Society of Salt Bucharest & Praid salt mine branch and the Ministry of Economy and Commerce. The platform provides a complex data base, for partners? selection and researchers? team structure. This can provide the scientific results with a high level of confidence for the projects of interest in the field of exploitation of mineral resources and for the participation on national and international project proposals competitions (i.e., target the 7th Framework Programme or any European / national programme, which can provide funds for the ECOMINING platform field of interest). The next step is the affiliation of the ECOMINING platform to the European ones, and to be compatible with them. The ECOMINING platform represents itself a 7th Framework Programme (FP) project idea.

Jan 1, 2007

By A. A. Campoli

A stress control design strategy was developed to minimize the explosive failure of highly stressed pillars, during room-and-pillar retreat mining conducted between stiff immediate roof-and-floor strata. A confined core coal pillar strength model was based on in-mine geotechnical evaluations of successful room-and-pillar and longwall bump control designs. Tributary area and linear shear angle approaches were used to estimate development and gob side abutment pillar loads for supercritical section widths. Subcritical width sections separated by barrier pillars to control stress within total extraction panels were optimized with the boundary element program MULSIM/NL.

Jan 1, 1994

By D. E. Larson

The U.S. Bureau of Mines has developed a image analysis methodology to correlate the energy consumed during the grinding of an ore to the mineral liberation achieved. Energy consumption values are obtained using a laboratory-scale ball mill equipped with a torque sensor, and an automated image analyzer is used to determine the liberation present in ground products. By combining liberation information with energy consumption data an appraisal can be made of the energy required to liberate the mineral(s) of interest. Results of tests performed on a complex sulfide material determined the effects of grind duration on the liberation achieved and the energy efficiency.

Jan 1, 1995

By J. K. Mudge, T. Allen, P. B. Johnson

Approximately 6 years ago, Newmont Mining Corporation (Newmont) initiated reclamation/closure at its’ Hollister operation in Nevada. Reclamation/closure challenges existed at three primary areas within the operation. One the open pits had a small, low pH lake. The primary waste rock dump had a collection system for seepage of low pH solution. The heap leach had a typical inventory of process solution. In each of these three areas water quality and water quantity challenges existed. Reclamation/closure techniques were employed that utilized run-on controls, re-sloping, capping/topsoil placement, pit backfilling and vegetation for water quantity control. Water quality controls included installation of passive, anaerobic systems. These mechanisms have effectively limited water volumes that require treatment and effectively treated the water to meet standards.

Jan 1, 2003

By James Paone

Subsidence movements have damaged houses, schools, streets, and public utility lines in some undermined sections of Belleville and Maryville, Ill. In cooperation with local officials and the State of Illinois, the Interior Department's Bureau of Mines is sharing experience in backfilling abandoned coal mines to demonstrate that bituminous coal mine workings in south-western Illinois can be successfully backfilled and subsidence-prone areas stabilized. Subsurface investigations revealed that mine workings are dry and underlain by underclay deposits susceptible to instability upon wetting. Backfilling will therefore be accomplished by pneumatic injection instead of the hydraulic methods used in previous subsidence-control projects.

Jan 1, 1977

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By David S. Young

All pigments and extenders or fillers whether organic or inorganic fall into the following broad general classes: I. Colored II.-White III. Black IV. Metallic A pigment- is any particulate matter that is essentially insoluble and chemically unaffected by the media into which it is dispersed. According to this very broad definition, colored pigments, white pigments, fillers, extenders, and functional pigments would all be included. The particulate size range would also be quite broad ranging from very fine colloidal particles (~0.01µ) to relatively coarse particles (~100.0µ). This broad definition is usually subdivided into more practical divisions which tend to relate the classification of the pigment to its primary function in the system in which it is used. Hence, the word extender implies that its major purpose may be to extend the system.

Jan 1, 1985

By Eugene N. Cameron, Igor N. Sviatoslavsky, Harrison H. Schmitt, Gerald L. Kulcinski

The recent discovery of large amounts of helium-3, a valuable thermonuclear fuel, on the surface of the Moon has prompted engineers and scientists to examine the commercial attractiveness, thetechnological feasibility, and the environmental features of this important resource. The main feature of this fuel cycle is the low (˜ 1%) fraction of energy released in neutrons. Such low neutron fluxes result in important reductions in the amount of radioactivity, afterheat, and radiation damage in a fusion power plant. On the other hand, the high fraction of energy in charged particles and synchrotron radiation can be directly converted to electricity, resulting in very high efficiencies of electricity production (˜60.70%). It has been shown that there is 10 times more energy in He3 on the Moon than there ever was in fossil fuels (i.e., coal, oil, and gas) on the Earth. The techniques and equipment needed to extract the helium-3 have been examined and internationally acceptable mechanisms for the industrial development of this resource have been outlined. This paper expands on the financial, environmental, and technical aspects of the recovery of helium-3 for use in the 21st century.

Jan 1, 1990

The dissolution behavior of gold and silver from Au/Ag alloys in aerated cyanide solutions has been investigated using rotating disc electrodes. The variables studied included concentration of cyanide, oxygen partial pressure and rotating speed of the disc. The dissolution potential and the rate of dissolution were obtained in view of the anodic and cathodic current-potential relationships. The results were discussed in terms of a mixed potential theory. The results showed that the dissolution rate of gold and silver from the alloys was partially controlled by chemical reaction, but largely by transport of either oxygen or cyanide, depending on their relative concentration under the experimental conditions employed in this study.

Jan 1, 1995

By W. R. VanSlyke

Scrubbing is gaining increasing recognition as a valuable tool in the treatment of Mesabi Range intermediate iron ores. In general, the earliest washing plants included log-washers in their various flowsheets. While log-washers certainly did impart a degree of scrubbing to the crude ore, such treatment bears little resemblance to the type of scrubbing being practiced today. At the time that these early plants were erected, only the true wash-ores were being processd. ("Wash-ores" are defined as crude ores in which relatively coarse chunks of almost completely liberated iron are found in a matrix of loosely-consolidated fine sand.) To treat ores of this type, sizing at approximately 65 to 100 mesh was sufficient to produce a merchantable concentrate. As crudes were being treated in which there was little "locking" of iron and silica, log-washers tended to disappear and large screens and classifiers took their place in Mesabi range flowsheets. The "screening and classification" type of flowsheet 'had its greatest usage in the 1945-55 period, generally speaking. During this same period, many operators found it necessary to supplement the "wash-ore" type flowsheet with heavy-media treatment.

Jan 1, 1959

By V. C. Koppe, J. F. C. L. Costa, D. M. Marques, A. Amaral

Errors associated with estimating the grade of an attribute of interest in a deposit can compromise planning, sequencing, and mineral beneficiation decisions. Several factors are associated with estimation errors. Among them, we can highlight the factors associated with sample spacing, the size of production volumes, and the variability of the attribute considered in the estimation. The access to estimation error can be obtained by some geostatistical methods, for example, by stochastic simulation. However, this is a process that in some situations is computer intensive and takes time. Previous works have proposed a simplified method to access the Maximum Estimation Error (MEE) associated with different types of grade variables, depending on the sample spacing, at small production volumes and considering specific coefficients of variation ranges. This paper presents an approach to assess the MEE associated with long-term volumes. Considering the methodology proposed, it is possible to approximate if a specific drilling pattern used in a deposit provides an acceptable pre-determined estimation error for Resource Classification. Results and considerations on the impact of the geometry of larger production volumes on the MEE calculation are also presented.

Jun 25, 2023

By S. D. Bearden

China was the world’s leading producer of barite during 1995 with 35%. The United States followed with14%. India produced 9%. Other producers included Morocco, Turkey, Mexico and Germany. Domestic production of barite during 1995 was estimated to be 600 kt (660,000 st). Nevada produced 85% of the total. Georgia was the second leading barite-producing state. The United States is the world’s largest consumer of barite. During 1995, it used 1.6 Mt (1.8 million st). US reliance on imported barite during 1995 was about 63%of total consumption, according to the US Geological Survey.

Jan 1, 1996

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018