Search Documents

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By Don Rose

Steel-fiber-reinforced-shotcrete (SFRS) methods of testing and the wording of specifications vary from country to country. In the USA ASTM C1018 is widely used. The Canadians have taken a close look at C1018 and point out that exact determination of the first crack is very subjective, and they propose a method of design that eliminates this variable. The Europeans (EFNARC) have taken the principles of testing a step further than ASTM C1018, and have added a new step in measuring the effectiveness of SFRS. EFNARC uses an "energy absorption" of a plate loaded in its center, in addition to the principles of C1018. The principles of SFRS design are also used in Japan, Norway and elsewhere.

Jan 1, 1999

By Jr. Schnakenberg

In 1986 the U. S. Bureau of Mines (USBM) embarked on a major research effort to develop technology that can substantially reduce worker exposure to face hazards simply by relocating the equipment operators to an area of relative safety. This reduced exposure mining system (REMS) research effort enhances the USBM ongoing health and safety research efforts to reduce and control dust and noise and to reduce accidents through training and better mining practices. This paper reports progress of the research that is developing and will demonstrate the technologies required for the computer-assisted tele-remote operation of continuous mining machines, haulage systems, and roof bolting machines.

Jan 1, 1996

By H. W. Newcomen, D. R. Brox

Assessments of the stability performance of open pit highwalls have traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work have been reviewed and are generally endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on the observed trends in highwall strain data from the case histories presented.

Jan 1, 2004

By Ihsan Berk Tulu, Mustafa Can Suner

The synthetic rock mass (SRM) approach and discrete fracture network (DFN) model, generated from the field surveys, are novel methodologies to study fracture rock mass behavior. In this paper, SRM and DFN methodologies were used to understand the influence of natural fractures on the mechanical response and failure mechanisms of stone mine pillars. First, a multi-stage up-scaling procedure with the homogenization process is established. Later, a stochastic sampling process on the SRM model to have further insight on the stone mine pillar mechanics is performed. Two-dimensional Universal Distinct Element Code (UDEC) is utilized to represent intact rock with the Voronoi-Trigon discretized blocks and to capture fractured rock mass behavior. The laboratory-size limestone mine rock specimens are systematically up-scaled to the average width of the field-size stone mine pillars. Then, the DFN model, generated from field data, is sampled to construct the SRM of the field-size pillars. By doing so, the effect of discrete discontinuities on pillar stability is studied by assessing the pillar strengths and failure mechanisms in various width-to-height ratios.

Jul 8, 2022

By Robert H. Scott

Developments during the past few years have brought coal-based composite fuels to commercial readiness. During the next few years, composite fuels will become available from a number of suppliers. Potential users must evaluate the combustion properties of these fuels to determine equipment and operating changes required for their use. Most work to date has been done with boiler applications. However, many potential non-boiler applications exist in the metals and minerals industry. These applications require specific evaluations appropriate for the processes involved.

Jan 1, 1982

By Norman E. Lehman

INTRODUCTION The Washington Camp - Duquesne mining district is located on the east flank of the Patagonia Mountains, 98 kilometers south of Tucson and within 5 kilometers of the International border (Figure 1). Since the development of high-grade silver and copper ores by settlers in 1862, the Washington Camp - Duquesne district has yielded an estimated 450,000 metric tons of ore. The mined ores averaged 8% zinc, 2% copper, 3% lead and 124 grams of silver. REGIONAL GEOLOGY The Patagonia batholith, of Laramide age, crops out in the core of the Patagonia Mountains intruding Precambrian granite, Paleozoic sediments and Mesozoic igneous, volcanic and clastic rocks. This granodioritic batholith lies in a northwest-trending zone of Laramide plutonic rocks, which can be traced for a distance of 320 kilometers from the Nacozari district in Sonora, Mexico to the Silver Bell Mountains west of Tucson, Arizona. Several major porphyry copper systems occur within this plutonic belt including the Red Mountain deposit found at the northern end of the Patagonia Mountains. Data from more than 80 mineral deposits within the Patagonia Mountains show metal zoning symmetrical to the Patagonia granodiorite (Graybeal, 1975). Disseminated copper-molybdenum deposits occur within the batholith. Pyrometa-somatic, limestone replacement and vein deposits of copper, lead, zinc and silver occur in the wallrocks adjacent to the. granodiorite and epithermal manganese-silver deposits occur at the outer periphery of economic mineralization. GEOLOGY OF THE WASHINGTON CAMP - DUQUESNE DISTRICT Stratigraphy Nearly 900 meters of miogeosynclinal Permian and Pennsylvanian sediments are exposed in the district (Figure 2). In addition, 700 meters of older Paleozoic rocks crop out 6 kilometers north of the district. The Paleozoic rocks occur in fault contact with a sequence of Triassic-Jurassic pyroclastic and flow rocks, ranging in composition from latite to rhyolite.

Jan 1, 1977

By Y. Xi

In this paper we present an availability approach for determining the capacity of a major bucket wheel excavator (BWE) system to be used in Yuabaoshan surface coal mine in China. Based on previous time studies on other BWE systems for delay times due to internal and external causes, and a four-level maintenance and repair schedule, we develop a model taking into account all random failures and present a fast and simple solution to this highly complex problem. A procedure employing the Markov renewal theory for determination of the distribution of random failure times and failure rate of the whole system, as well as some other factors useful for calculation of the overall system capacity are discussed in the paper.

Jan 1, 1993

By Y. C. Guan

In an attempt to replace the traditional cyanide process of extracting gold, a new technology using ammoniacal solutions has been developed. In this study, the electrochemical behavior of gold in ammoniacal solutions at temperatures above 100°C has been investigated. An electrochemical cell in an autoclave has been introduced to carry out this study. The system consists of a gold working electrode, a platinum counter electrode, and an external saturated calomel electrode (SCE) which is connected to the autoclave system through a Birch wood plug. Techniques used in this study included potentiodynamic polarization, galvanostatic polarization, cyclic voltammetry, and Tafel polarization. The electrochemical reaction mechanisms governing the dissolution process are presented.

Jan 1, 1996

By D. M. Davidson

The economics of geologic exploration have changed materially in the past decade primarily due to the change in three basic factors, namely, increased wages and salaries, increased cost of materials, and a greater complexity in methods of exploration. Following the general economic pattern over the past ten years, exploration costs, have, in general, increased, although there is one heartening exception. A comparative picture is complicated because of advances in techniques which ensue from the introduction of new methods and devices largely for aerial exploratory work, Some of these methods were either in their infancy or unknown before World War II. Geological exploration may well be considered as a form of applied research. True, it has peculiarities from this standpoint some advantageous, others disadvantageous, Some of the advantages lie in the fact that exploration success does not involve the production of a new product which necessitates advertising expense and marketing problems. In normal times there is a well established market for the fruits of a successful mineral find. The outstanding disadvantage of exploration lies in the enigma of deciding when to quit if the sought fop prize is elusive. In the search for buried treasure, man?s curiosity is apt to color his judgment. Even the so-called detached scientist may fall 'all too readily into the wishful thinking of the old- time prospector who is lured on by the thought that the next pull from the drill hole, or the next round from the face will reveal a bonanza. It involves mature judgment and experience to ascertain the stage in exploration when further work is not justified.

Jan 1, 1958

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By H. M. Breza

Recovery of phosphate concentrate has received increased attention as the existing mine and plant production capacity limitations of the Texasgulf Inc. Aurora, North Carolina Mine are reached. Improved mining techniques and mineral processing of waste streams offer a potential to increase overall phosphate production without major expansion of the Mining facility. Innovative processes have been or are being identified to maximize pit mining recovery and to minimize losses in waste streams, resulting in more effective use of the valuable phosphate natural resource. This paper will describe the various continuous recovery improvement programs being implemented to achieve this goal.

Jan 1, 1994

By G. R. Burman

Gilsonite is a brittle, natural solid bituminous resin, classified as an asphaltite. It is found in near-vertical veins in the Uintah Basin of Eastern Utah. Discovered well over 100 years ago by Samuel Gilson, this unique material has, since its finding, enjoyed a variety of commercial and industrial applications. Early uses for the product included black automotive paint and beer vat linings. Among its many important uses today are additives for oil well drilling fluids and cements, additives for sand castings for the foundry industry, reinforcing agent for asphalt pavements, and dispersing agent for black inks. Gilsonite is mined and processed in Bonanza, Utah, by two companies, American Gilsonite Company (AGC), an operating division of Chevron Resources, and Ziegler Chemical, a privately held company headquartered in New York.

Jan 1, 1990

By V. Srivastava, T. Ghosh

The modeling and simulation of semiautogenous (SAG) mills have been widely used in the design and optimization of mill performance in terms of its power draw, processing capacity and product size distribution. However, these models are solved under steady approximation and do not provide any information on mill charge distribution in real time. 7KLVSDSHUDWWHPSWVWRFKDUDFWHUL]HPLOOFRQWHQWVE\VROYLQJ:KLWHQ¶V¿UVW RUGHUFRQWHQW EDVHGPRGHOLQWKH0$7/$% Simulink environment. The parameters in the model, such as breakage rate constant, discharge rate and appearance function, were estimated using process and design data collected from a gold mine operating in Alaska coupled with a nonlinear parameter estimation scheme. This model was then used to predict the dynamic responses of other key operational variables, such as mill power, bearing pressure, charge level and product size distribution. The transient response of mill behavior with respect to changes in feed size distribution, tonnage and mill feed water is also presented. This dynamic simulation approach can be used for practicing different control strategy and training purposes. The observed response of mentioned variables was validated using dynamic response data from the plant to encompass operational characteristics of SAG mill behavior.

By V. M. Lepetic

Large tonnages of copper and molybdenum sulfide ore are treated by flotation. Substantial savings could be realized, particularly in high-capacity concentrators, by use of a simplified flotation technique involving lower reagent consumption. Chalcopyrite and molybdenite from some deposits can be floated by use of only a frother as a single flotation reagent; acceptable concentrate grade and recovery can be obtained. Separation of molybdenite from copper sulfides may become simpler and less costly. The genesis of the ore and the ions present in the flotation pulp liquid phase appear to be the major success-determining factors.

Jan 1, 1972

By Christina Dahnér, Kristina Jonsson, Savka Dineva

The iron-ore underground Kiirunavaara mine (Sweden) has been seismically active since 2008. In 2021 the production is on levels 1079 and 1108 m, at the deepest. The seismic activity has changed in character over time with one step change in 2015 when the number of large (ML>2) seismic events increased, and another one when the mine experienced a seismic event with Mw 4.2 in 2020. In 2017, the mine evaluated Hydraulic Fracturing (HF) as a possible mitigation technique for larger seismic events and a one-hole trial was performed. The trial proved promising, and it was decided to go forward with a large-scale trial covering an entire production area in the mine. The large-scale trial consists of 25 fracturing holes, 50 – 100 m long, running along 500 m out of the ~4500 m long orebody and spanning between production levels 1108 m and 1252 m. The fracturing process continued for a year, resulting in ~38,000 seismic events with −3.3<ML<1.4. The breakdown pressure varied between fractures in the same hole as well as between holes in the same area. Average breakdown pressure per hole was between 12 MPa and 50 MPa. The seismic response to HF in 2021 varied greatly from hole to hole and between fractures in the same hole. The variation in response could be related to the geological conditions and the infrastructure, such as large caving ore passes. In this paper some details about the experiments and broad preliminary analysis of the effect of the HF by using seismic source parameters of the induced seismic events are presented: 1) Distribution of seismic activity, 2) the ‘equivalent’ magnitudes for each hole calculated from the cumulative seismic energy and seismic potency released during the fracturing, compared with the local geological conditions; 3) the predominant failure mechanism of the seismic events caused by HF was defined. A difference in the behaviour between larger and smaller events was noticed, as ML>0 events seem to be compression type failures and ML<0 events seem to be related to slip on pre-existing structures. No seismic events related to creation of a new fracture have been identified yet.

Apr 26, 2022

Application of flotation for the removal of hydrophobic compounds from soils was studied. Bench scale flotation tests were conducted on artificially contaminated soil, using both conventional mechanically agitated machine and flotation column. Flotation parameters tested include surfactant collector type, conditioning time, flotation time, surfactant dosage, pulp pH, solid/liquid ratio in conditioning and pulp temperature. It is found that with conventional flotation 74% removal of the contaminant was achieved from soil particles in the range of 75-830 µm; with column flotation up to 80% of oil could be removed from the 250-830 µm soil fraction, and 65% from the 75-830 µm fraction. Flotation was found to have considerable potential for cleaning up contaminated soils.

Jan 1, 1998

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006

By S. Anderson

Advances in inexpensive computer automation led to the development and utilization of a computerized ore control system at Cyprus Coppers tone Gold Mine near Parker, Arizona. These new ore control practices improved accuracy, performance, and productivity of the ore control effort. An automated system for data collection, including bar coding of blast hole samples, laboratory analysis, data management, grade estimation, cut delineation, and ore zone stakeout, plays a major role in ore control practices. This is of particular interest because of the large amount of blast hole information being processed, analyzed, and reported daily.

Jan 1, 1991

By R. Wisniewski

Every underground coal mine in the United States must deploy and operate a wireless communication and tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 96 hours, and the requirements in the MINER Act for the tracking systems to be ?calculated to be serviceable? and the communications systems ?redundancy?. These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using the tools that are available and commonly used by the Reliability, Maintainability, & Availability community.

Feb 23, 2014