Search Documents

By W. Petruk

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections in order to characterize a mill product and to determine the apparent mineral liberation. It was found that a representive polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly individual screened' fractions are not representative of the sample because minerals are partitioned during screening. Consequently the quantities of soft brittle minerals are increased in fine grained fractions and quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (1 Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analysing each fraction and combining the data. Somewhat less accurate data would be obtained by analysing a series of screened, fractions that have a wider size range of particles (5 Tyler size ranges). Mineral liberation analyses show that the most reliable apparent mineral liberation in each screened fraction is a value taken from a smooth curve drawn through the lowest points on a graph of % free vs size. A correlation between the apparent mineral liberation in screened fractions and calculated mineral liberations using Kings liberation model is good for sphalerite but not for chalcopyrite and galena.

Jan 1, 1985

By Dirk van Zyl

Natural materials can be used successfully in the construction of heap leach pads. The use of these materials usually result in the least expensive approach for such facilities. Sufficient geotechnical experience has been gained in the design and construction of clay heap leach pads so that they can be used with confidence. A number of operators presently use clay pads in their heap leach facilities; these include Alligator Ridge, Ely, Nevada (gold), and Union Carbide, Gas Hills, Wyoming (uranium). This paper describes the construction and field investigation of a clay pad for the heap leaching of agglomerated precious tailings. The project is located in the Mojave Desert, Southern California. The design had to satisfy operational requirements as well as regulatory requirements. The California Water Quality Control Board (WQCB) was one of the agencies which had to issue a permit for the project. Their biggest concern was the discharge or escape of cyanide into the environment. Rather stringent requirements were therefore placed on the pad design criteria, especially in terms of permeability.

Jan 1, 1983

By A. H. Farazi, C. Quamruzzaman

The freezing and subsequent solidifying of unstable, weak (sands, silts and clays) and/or wet soil to form a desired-shape frozen barrier around a construction area are possibly the main features of the freezing method for shaft sinking. The barrier, along with strengthening the soil, provides a dry environment to ensure sustainable subsurface construction work before placing a permanent lining. The freezing method requires the installation of freezing pipes in boreholes around the construction area and the circulation of chilled salt water through these pipes and has long been a proven technique for dry shaft sinking through unstable and water-bearing seam around the world. As removing heat from the ground is the main feature of the method, an efficient thermal design of the freezing process is mandatory to ensure success of the shaft sinking operation. This applies to both the sustainability and economy of the intended structure. The design presented in this paper is aimed at figuring out the heat-removing ability and operating time of the refrigerative equipment using some simple formulae. The authors adopted a theoretical approach to determine the quantity of heat to be removed from the ground. The amount of energy for the equipment was found to be greater than that for freezing, which proved the validity of the design. The active freezing period was calculated to be 121 days. The authors followed the structural design of the freezing process they proposed in their previous work (Farazi and Quamruzzaman, 2013). Though the first coal seam in the coalfield was encountered at a depth of approximately 352 m in the subsurface, the target depth for cooling and freezing was decided to be 162 m. The formation demands extra care to nullify its risk of the temporary structure collapsing and water rushing in (Farazi et al., 2012). Discussion on the determination of refrigerative equipment parameters was excluded from the scope of this work.

Jan 1, 2014

By G. S. Dobby

The Cu-Au flotation cleaning circuit at Freeport Indonesia consists of three stages: two flotation column stages, in series, followed by one stage of mechanical cells. Concentrate from both column stages is combined as final concentrate. The mechanical cell stage has two parallel rows of seven Wemco 500's. The Wemco concentrate is recycled to feed of the second column stage and Wemco tails report to final tailings. This paper examines cleaner circuit performance, focusing on size-by-size performance of the individual stages and the individual mineral groups -copper sulfides, gold and in sol minerals. The recovery mechanisms of insol minerals are examined.

Jan 1, 1995

By J. N. Cox

Coal preparation is based on the properties of noncombustable materials (impurities) in coal being different from the organic constituents. The most commonly used property difference is density, via its affect on settling rates; and either gravitational or centrifugal forces can be used to remove impurities. However, examination of various particles settling rate correlations shows that at smaller sizes, particle drag becomes a very important factor. Classification, based on differential settling rates, becomes impractical and some property other than density must provide the basis for fine coal cleaning. Froth flotation and agglomeration employ differences in surface properties to clean coal. These methods are very successful except that the oxidized surface of a pyrite particle is somewhat hydrophobic and will tend to be collected with the organic portion of the coal. Surface property cleaning techniques have not been very effective in rejecting sulfur, except for two-stage flotation.

Jan 1, 1984

By J. Pancher

"Stainless steel castings are used in abundance in the mineral processing industry. In rotary kiln-based processes, these castings are typically exposed to high loads, corrosive elements, mechanical abrasion and cyclical temperature exposure. In the processing of iron ore pellets, it is typical to use a traveling grate preheater or a straight grate furnace to heat the pellets. Both machines have a conveyor that is mainly comprised of high temperature stainless steel castings. It is these castings which are the focus of this study. The expected life of these castings can be quite short, their cost quite high and the effort to replace them very labor intensive. The goal of this study was to gain a better understanding of the failure modes of these castings. With that basic understanding, modifications to the alloy content could be made to achieve a new operational paradigm. That paradigm could be a cheaper casting, a longer lasting casting or a casting tailored to special operating conditions (for example, highly corrosive gases or sudden temperature shocks). Over the past 4 years, Metso Minerals has sought to achieve a better understanding of the failure modes through modeling, laboratory testing and sampling of used castings from various end-users. In addition, we have tested new alloys in a laboratory setting and also in the field to see how they would perform compared to the existing ""standard casting"". Our testing has revealed interesting data concerning the impact toughness, sigma phase content and formation, chloride attack and other performance attributes of various grades of stainless steel when exposed to cyclical temperatures. Interesting results were also obtained concerning the addition of rare earth elements (Niobium, Boron, etc), nitrogen and manganese to a typical ASTM A297 grade of stainless steel. To date, a few hundred test castings have been installed in iron ore pellet plants worldwide. Many of these test castings have already experienced a year or more of operation with good results.INTRODUCTION Cast stainless steels (ASTM A297 and similar) are a main constituent used in the construction of iron ore pelletizing equipment. A typical straight grate pelletizing machine would contain upwards of 160,000lbs of ASTM A297 Grade HH castings. With a typical casting lasting only two to four years, and a casting costing around $35USD, it is easy to see that the castings are a main contributor to the overall cost of producing the pellets. Grade HH and HI (see chemical composition listed below) became the “go to” materials in the 1960’s and very few changes have been made to this day (the exception being plants that switched to flux pellet production in the 1980’s)."

Jan 1, 2015

By R. R. Dorfler

The existing regrind circuit at the Climax Operations uses sodium cyanide and Nokes reagent to reject pyrite, copper, and lead minerals. Laboratory flotation studies were performed using feed to flotation following first-stage regrinding. The effects of conditioning time, pH, and the concentration of depressants such as Nokes reagent and sodium cyanide on the rejection of pyrite, lead, and copper minerals were investigated. The metallurgical results indicate that, in the presence of depressants, the rejection of copper is strongly dependent on the pH. Preliminary mill testing confirmed the finding. The rejection of impurities is also dependent on conditioning time. The recovery of molybdenite is independent of the variables investigated.

Jan 1, 1981

By J. Helton, J. L. Bellanca, M. McNinch, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Accident data indicates that mobile haulage poses a significant pinning, crushing, and striking risk. Proximity detection systems (PDSs) have the potential to protect mineworkers from these risks. However, unintended consequences of mobile PDSs can undermine the safety benefit they provide. Soliciting iterative user input can improve the design process. Users help provide a critical understanding of how mobile PDSs may hinder normal operation and endanger mineworkers. Researchers explored users’ perspectives by conducting interviews with mineworkers from seven mines that have installed mobile PDSs on some of their haulage equipment. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance, and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure, and risk. Mineworkers also suggested that improved task compatibility, training, logistics, and PDS performance might help address some of these identified issues. This paper also gives additional insights into mobile PDS design and implementation. INTRODUCTION Pinning, crushing, and striking accidents are a large problem in underground coal mines, especially for mobile haulage. Between 1984 and 2014 there were 179 non-fatal and 42 fatal pinning, crushing, and striking accidents involving mobile haulage vehicles, including coal hauling machines and scoops [1]. Proximity detection systems (PDSs)—automated systems that decelerate and stop a vehicle in order to prevent a collision—have the potential to protect mineworkers in these situations. In fact, PDSs are now required on all place change continuous mining machines as of March 16, 2018, as a result of the final rule published in January 2015 (30 CFR 75.1732) [2]. To address mobile haulage, later in 2015 the Mine Safety and Health Administration (MSHA) also proposed a new rule that would require PDSs on mobile haulage vehicles [3]. Though there has been no additional actions related to the proposed rule and it is not currently required, mobile PDS can still help to save lives. MSHA estimates that the adoption of mobile PDSs could prevent approximately 70 injuries and 15 fatalities over the next 10 years [4]. As of June 2015, the underground coal industry had already equipped 155 of the 2,116 mobile haulage vehicles in use [1]. In order to capitalize on the projected safety gains afforded by PDSs, it is important that the systems are designed and implemented effectively. Along with others, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been exploring PDSs for more than two decades [5-7]. Throughout this time, NIOSH has also held several stakeholder meetings (2010, 2014, 2016, and 2017) in order to disseminate information and provide an opportunity to discuss on ongoing issues and concerns. Despite some progress, human factors remain a key concern. Previous research examined mineworkers’ attitudes towards PDSs on continuous mining machines [8] as well as how continuous miner operators’ perceptions of risk have changed as a result of PDSs [7]. However, stakeholders have still expressed a need to better understand how mobile PDSs affect the mining process, the mineworker, and whether and how they may present previously unidentified risks.

Jan 1, 2019

The properties of interfacial water at hydrophilic surfaces are of great importance in many technological areas including flotation, solid-liquid separation, dispersion and emulsions, flocculation, adsorption, corrosion, and soil contamination. This paper examines the use of FTIR/internal reflection spectroscopy (FTIR/IRS) to study the spectral characteristics of interfacial water at silica surfaces. FTIR spectra were characterized by consideration of the OH stretching region (3000-3800 cm-1) associated with the vibrational spectra of interfacial water. The broad peak in this region was deconvoluted in order to isolate overlapping spectral features that describe the nature of hydrogen bonding in interfacial water. Three distinct bands were found; -3600 cm-1 (free OH), -3400 cm-1 (incomplete tetrahedral coordination), and -3240 cm-1 (complete tetrahedral coordination) and the variation of their intensities with pH was found to be significant. This spectral information helps to explain orientation and bond ordering of interfacial water molecules at hydrophilic surfaces.

Jan 1, 1998

By Z. Hajnal

Three years ago a research program was initiated at the University of Saskatchewan to develop seismic surveying techniques for use in the Precambrian geological environment. The success of the reflection method in many younger geological settings suggested that this is the technique which would be the most suitable for experimentation. A successful adaptation of this technique to the Shield environment would make mapping of rock formations possible to much greater depth than is possible at the present time with any other applied geophysical technique. This presentation attempts to illustrate the advances which have been made in this program and will provide some insight into future plans. The field investigations were limited to the Flin Flon basin near to the town of Flin Flon, Manitoba (Fig. 1). This area was chosen because the surface geology has been mapped in great detail and it is a very important base metal producing region. It is an ancient sedimentary basin with some characteristics similar to areas where the reflection method has been successful.

Jan 1, 1976

By M. Z. Mubarok, Z. T. Ichlas, A. T. Sugiarto, K. Sukamto

The use of ozone as an oxidant for the direct leaching of zinc sulfide (sphalerite) concentrate in sulfuric acid medium under atmospheric pressure was explored. The influence of acid concentration, feed gas injection rate, particle size distribution, stirring speed, temperature and slurry density on zinc extraction efficiency was examined. The experimental results showed that the leaching efficiency depends on all of these operating parameters except for stirring speed. It was found that essentially complete dissolution of zinc from the concentrate with the present method can be achieved in only about seven hours under the conditions of sulfuric acid concentration of 2 mol/L, particle size smaller than 74 µm, slurry density of 50 g/L, stirring speed of 420 rpm and feed gas injection rate of 1 L/min at ambient temperature. The experimental results suggest that the dissolution reactions produce independent elemental sulfur that is readily floated and can be easily separated rather than forming a layer on the surface of the reacted particle, as usually observed in a system with ferric-sulfate as oxidizing agent. It was therefore determined that the dissolved ozone play a key role in improving the rate of zinc dissolution from the concentrate. Analysis of the leaching kinetics indicate that the leaching rate follows the shrinking particle model, and the overall dissolution rate of zinc is controlled by a surface reaction.

By Barbara J. Arnold

A coal's size distribution, clay content and moisture content can affect its handling behavior, but the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.' s (formerly EPRI' S) Coal Quality Development Center (CQOC) and at Iowa State University (ISU) will answer these questions as part of a four-year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of various coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that, while moisture content-is the most important variable, the amount of -325M (-0.044 mm) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1990

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By D. R. Taylor

The use of clay granules as carriers for pesticides dates from the early 1940's and by the present day represents a business conservatively estimated at between 200 -300 thousand tons / year in the U.S. alone. Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits which will be reviewed. Topics to be discussed will include: I) drift control (versus liquid sprays), 2) mobility (in the environment), 3) worker safety, and 4) transportation (spill) safety.

Jan 1, 1999

By R. W. Carn, D. Vincent

During the next 15 years, US coal production is expected to double, with the increased production evenly divided between the East and the West. Along with greater production, coal export markets should increase dramatically from East, West, and Gulf Coast ports. The annual overseas export capacity of US coal-loading terminals is expected to rise from 147.1 Mt (162.1 million st) in 1981 to a minimum of 278.1 Mt (306.6 million st) in 1985, according to the US Maritime Administration. Increased coal production and use will lead to more development of import and export terminals, a vital link in the coal transportation chain. With continually escalating capital costs and the competitive markets that the terminals will serve, a well designed and efficient terminal is necessary. This article begins a two-part series that presents concepts presently used in coal export terminal design. Part I looks at site selection factors and equipment needs, while Part II will examine environmental considerations in building a terminal as well as typical capital and operating costs. The world is nearing the end of the oil era. In a few years oil will not be available to sustain the growth rate and increasing standard of living we have known in our lifetime. The big question is what energy era are we moving into? With the decline of readily available oil reserves and rapidly increasing prices, many countries are trying to switch to alternate energy forms. While intensive efforts to find new oil reserves continue, alternate energy sources such as natural gas, coal, synthetic fuels, nuclear, hydroelectric, solar, and wind power are being developed. Recent indications are that coal is expected to bridge the energy gap over the next 25-30 years until the technology and economics of the alternate energy forms reach satisfactory levels. Use of coal for energy is receiving strong attention due to its long-term availability (200-300 years minimum), relative ease of development, and its low cost per unit of power produced. By the year 2000, it is expected that 25% of world energy supply will be met by direct coal combustion and possibly another 5-10% by synthetic fuel from coal. Coal's expanding share in the world energy market, along with an increase in coking coal requirements, will result in a large increase in the world's seaborne coal trade. Recent statistics and projections for the future are shown in Table 1. This phenomenal development rate includes increases in both coking and thermal coal requirements. Because of the rapid increase of seaborne coal trade during the last 10 years and the even greater projected increase of trade to 2000, various sectors of the coal industry are faced with enormous technical challenges and huge investments in equipment, land, transportation systems, and port facilities. Very large bulk terminals are under development throughout the world. Latest surveys indicate that there are about 30 new coal export and import terminals under consideration and at least 30 existing terminals have expansion programs planned or underway. With the high cost of borrowed capital and rapid inflation rates there is great emphasis on new planning and design techniques to minimize capital and operating costs of coal transportation systems. Terminals A total coal supply system can be considered to consist of one or more mines; a train, barge, truck, or other haulage system; an export terminal; a fleet of bulk carriers; a receiving terminal; and possibly, local inland distribution networks that include barges and railways. Terminals, though only a small link in the total transportation system, play a key role in overall system efficiency. At ports or inland distribution centers, terminals act as transportation links bringing trains, ships, barges, or trucks together for cargo transfer and temporary storage. A well-designed terminal can provide maximum independence between two modes of transportation and optimum freedom for intermodal interference. A terminal acts as a buffer between the two transportation modes by providing sufficient storage capacity so a ship need not wait for its cargo on, for example, a train-by-train basis, but can load immediately from the ready stock. Similarly, a train need not wait for a ship to unload its contents but can dump immediately into storage. A terminal also can be used to properly mix various types of coal to satisfy a buyer's requirements. Consider the relative value of various production and transport segments for a typical steam coal

Jan 6, 1983

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By Jr. Foot

EIMCO Process Equipment Company has introduced the new SmartCell series of conventional flotation cells. The flagship of this new development is the 5000 ft3 cell that is the largest available in industry. This new series of cells includes a cylindrical tank design, a conical draft tube and froth crowder. Optional air control, wash water addition and embedded expert control are available. A discussion of the design parameters, energy efficiency, testing, and commercial plant results are presented.

Jan 1, 1997

By J. M. Dean

The MANpower SUPport Program (MANSUPP), a part of the Mine Management Support System (MMSS), allows an underground coal mine site user to determine manpower requirements for production support work by considering ongoing operations and current mine conditions. The objective of MANSUPP is to plan a detailed manpower structure for a mine by incorporating a production schedule, condition-modified work standards and management preferences to predict required manhours for various activities, for example, belt moves. The program is written in Quattro Pro version 3.0 (Lotus 1-2-3 compatible) utilizing the command language, macro and formula capabilities.

Jan 1, 1992

By William Gleason

"With desert temperatures climbing high at Caterpillar’s Tinaja Hills Demonstration and Learning Center near Tucson, AZ in September, a group of editors were given a reprieve from the sun and stepped inside the new Cat Minestar Command Center. The movie theater-like temperatures inside were a welcome relief, and the computer screens stationed around the room were an indication of not just how much things have evolved in the mining equipment sector, but also a peek into the future of where mining is headed.Equipment manufacturers like Caterpillar have always had to deal with peaks and valleys in demand that come with mining, perhaps never more so than in the last five years. Sudhanshu Singh, global product manager for Caterpillar, said that in one month in 2012, at the height of the mining Super Cycle, Caterpillar produced more than 150 large mining trucks (haul trucks that carry 136 t/150 st or more). By contrast, Caterpillar produced about 80 of those trucks in the full year of 2016. Between 2012 and 2016, Caterpillar saw its profits drop by 40 percent.“This shows how cyclical the industry is, and it is a testament to the strength of Caterpillar to be able to tolerate the wide swings,” said Singh. Demand for commodities is once again on the rise as are commodity prices with many signs pointing toward a recovery for the mining sector, and Caterpillar has positioned itself for the recovery. During its 2017 press event in September, company officials emphasized that Caterpillar has added strength in its technology divisions by forming new partnerships and adjusting its operating plan.“At the heart of our enterprise strategy is the operating & execution (O&E) model, a strategic framework to identify areas of the business that either create or consume the most value,” said Caterpillar chief executive officer, Jim Umpleby. “Using the O&E model as a guide, we gain a deeper understanding of where we have a competitive advantage, which is key to generating high returns.”"

Jan 11, 2017