Search Documents

By W. H. Jang

Although surface chemistry fundamentals of semi-soluble minerals have been studied by many researchers, detailed understanding of these systems is still incomplete. In-situ FT-IR/IRS techniques have recently been used to successfully describe the adsorption of carboxylates at semi-soluble mineral surfaces. However, the wetting characteristics of these adsorbed films require further consideration. In this regard, the hydrophobicity and stability of transferred Langmuir-Blodgett (LB) monolayers of fatty acids at fluorite and calcite surfaces has been studied by contact angle measurements with polar and apolar liquids. Generally, it was found that the transferred LB monolayers of fatty acids at a calcite surface are unstable whereas such monolayers transferred at a fluorite surface are stable, as revealed from advancing and receding contact angle measurements. These results are believed to be due to the incomplete reaction of fatty acid monolayer at the calcite surface. In addition it was found that a closely packed well-ordered stearate monolayer with good hydrophobicity, equivalent to that of a transferred LB monolayer, can be formed at fluorite surfaces by spontaneous adsorption and self-assembly from aqueous solutions.

Jan 1, 1995

By G. Schriever, H. Thiel, E. J. Foell

A long-term, large-scale, disturbance-recolonization experiment with relevance to the environmental effects of deep seabed mining is described. The study is funded by the German government and was launched in the abyssal eastern tropical South Pacific Ocean in February-March, 1989. After obtaining pre-impact baseline environmental data, a 10.8 km2 (4.2 sq miles) circular area of seafloor was disturbed using a specially designed "plow-harrow" device. An initial post-impact sampling series was carried out immediately after disturbance followed by a second post-impact sampling series six months after the disturbance. Plans call for repeated visits to the site at two year intervals to monitor the anticipated slow recolonization process until the area is inhabited by a new, stabilized community.

Jan 1, 1993

By Jian Deng, Hehua Zhu, Lianyang Zhang

Rockburst is defined as a sudden and violent explosion of rock on the surface of a rock excavation. Rockburst has been regarded as the least understood and most feared hazard problem for underground rock excavations. Traditionally, rockbursts were classified into the strain, pillar, and fault-slip categories. However, rockbursts are also known to occur at stress levels well below the rock yield strength, in mines where the rock is far from brittle, or without the presence of geological discontinuities. A plausible explanation of rockbursts is buckling, which has been identified as one of the main mechanisms for rockbursts. It is observed that rockbursts are often induced by dynamic loadings (pulses) from adjacent blasting. Therefore, the present paper studies the effect of pulse shape and amplitude on pillar rockbursts induced by dynamic loadings from blasting using the method of numerical analysis. The governing equation of a pillar’s motion is set up and the mechanism of pillar rockbursts is investigated through a practical example. The results show that it is not the shape of a pulse but the impact energy to decide the occurrence of pillar rockbursts. If all other parameters remain the same, pillar rockbursts are more likely to occur when the pulse duration is longer. The parametric resonance and the perturbation of dynamic loadings are also found to play an important role in the occurrence of rockbursts. These insights would provide invaluable clues about the mechanism and for better control of pillar rockbursts.

Apr 26, 2022

By H. V. Fairbanks

The following processes were investigated using ultrasonic treatment in mineral recovery: (1) cleaning coal from coal slurry ponds, and (2) extracting precious metals from tailings and other sources. The treatment entails the production of a water slurry of the material containing the mineral which is made to flow over the vibrating surface of the ultrasonic treatment unit. The vibrations transmitted into the slurry break up particle agglomerates and also produce a scrubbing action on the surfaces of the particles. The treated mineral particles were found to have increased settling rates, better compaction, and more rapid water drainage.

Jan 1, 1990

By B. Anameric

Considerable effort has been directed towards understanding the carbothermic reduction mechanisms of self-reducing, fluxing dried green balls to produce pig iron nuggets. Given the geometry of the situation, some investigators believed that the shrinking core model was applicable. Hence, this study involved investigation of the applicability of the shrinking core model to pig iron nugget production. The experiments involved heat treatment of dried green balls utilizing either a laboratory-scale resistance box furnace or a gas-fired muffle furnace at various furnace temperatures and residence times. The products were analyzed for the following: (i) preferred reaction pattern, (ii) distribution of the metallized areas, (iii) % iron content variation in the pig iron nuggets from surface to center, (iv) carburization pattern and (v) physical and chemical properties of the pig iron nuggets. It was determined that the reduction of iron oxide occurred simultaneously throughout the sample and not beginning at the surface and propagating inward; thus the shrinking-core model was not applicable. Heat transfer and gas diffusion from surface to center were not the rate-limiting steps for reduction and carburization reactions.

Jan 1, 2011

By R. S. Datta

In the article "Concentration of Oil Shale,"(1) Dr. N. Arbiter stated, "One of the major factors in the delayed utilization of oil shale as an energy raw material is the low grade or content of hydrocarbon (kerogen) in oil shale as compared with coal and even more so to the liquid and gaseous fuels. " When the availability of high-grade deposits decreased, mineral industries started adopting prebeneficiation procedures for the low-grade deposits. This practice, which is becoming standard in these other industries, has been largely overlooked by the oil shale industry in its drive to produce oil from oil shale. If a major portion of this mineral matter can be removed, there can be potentially large savings in the capital and operating costs of oil shale retorts. Moreover, the environmental impact, associated with recovering the shale oil, could be reduced considerably. In 1980 Roberts & Schaefer Resource Service (RSRS) completed successfully the first set of demonstration runs with a 20-ton oil shale sample from Cathedral Bluffs (C-b tract), Colorado. This relatively low grade (~12 gpt oil content) oil shale was beneficiated applying the Dutch State Mines Heavy Medium Cyclone process. (2)

Jan 1, 1985

By Kenneth N. Han

The effect of anions such as sulfate, chloride and nitrate on the solubility of rare earth element (REE)-bearing phosphates and fluoro-carbonates was examined using relevant thermodynamic data. The study found that these anions have significant influences on the overall dissolution of REEs from various sources in the aqueous media.

By J. B. Hiskey

The principle oxide minerals of molybdenum are wulfenite (PbMoO4), ferrimolybdite (Fe2(MOO 4)3.nH2O), powellite (CaMoO4), and ilsemannite (Mo304). Wulfenite is found in Arizona, New Mexico, Nevada, Utah, California, and Montana. It is also found in the states of Sonora and Chihuahua, Mexico. Prior to 1915 wulfenite ores were the primary source of molybdenum. The solubility of wulfenite in hot sodium sulfide was first noted by Bonardi(1) during attempts to sulfidize wulfenite material prior to flotation. He identified lead sulfide and soluble sodium molybdate as reaction products. Bacon (2) sulfidized wulfenite in preparation for flotation and by X-ray analysis found the reaction product to be lead sulfide. Holmes(3) made an extensive investigation of the extraction of molybdenum from wulfenite concentrates by leaching. Nearly 100% molybdenum extraction was possible from -100 mesh samples leached for 15 min with 10% sodium sulfide solution at room temperature. Molybdenum extraction from -100 mesh samples after leaching 30 min at a temperature of 45°C using 2, 4, and 6% sodium sulfide was about 32, 79, and 98% respectively. The extraction showed little sensitivity to time, temperature, or particle size using 10" sodium sulfide solution.

Jan 1, 1976

By Timothy J. Matthews, Timothy J. Batchler, Daniel J. McElhinney

The National Institute for Occupational Safety and Health’s (NIOSH) Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division was commissioned for operation in 1981. The MRS was originally designed for longwall shield research and was the only hydraulic press in the world with the capability to apply biaxial loads to these large structures. The results of this forty-year research program have contributed to improved performance and increased knowledge of longwall shields, mobile roof supports and hydraulic cylinders in the mining industry. Also, considerable research and development have been conducted to develop standing support technologies for the mining industry. The Support Technology Optimization Program (STOP) was developed to evaluate how these various technologies can impact and improve both ground control conditions and mine safety. Additional MRS research has included the performance of ventilation stopping walls including the development of a new testing protocol to evaluate the transverse loading capabilities under arching load conditions and evaluating the performance characteristics of welded wire screen as used in underground mine roof surface control. The NIOSH Mine Roof Simulator has been a reliable and valuable tool for the past forty years for the evaluation of safety structures used in mining, and this research has contributed significantly to the advancement toward safer mines. This paper will summarize those research results and provide a glimpse of planned future activities.

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes. Water is routed to the roof bolter from the main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/m3, and during the cleaning of the dry box the average respirable dust concentration was 1.188 mg/m3. The silica content of the roof material was high, ranging from 28.9% to 52.7% during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60%when cleaning the collector boxes. INTRODUCTION Currently, the dry vacuum dust collection system is the standard dust collector on roof bolters in underground coal mining. It has been proven to be an effective dust control to prevent roof bolter operators’ overexposure to coal mine respirable silica dust during roof bolting operations [Potts eta l, 2011 and Colinet, 2013]. The dry collection system works as follows: drill cuttings are vacuumed into the precleaner. The precleaner dumps oversized material onto the mine floor while undersized material enters the dust box via vacuum airflow produced by a blower. The cuttings entering the dust box are either deposited on the floor of the dust box or into a dust collector bag. The vacuum airflow leaves the dust box through a final filter which removes any small particles from the airflow. Figure 1 shows the internal view of two dry collection system boxes; one that does not use the dust collector bags and another that uses the dust collector bags. Dust collectors that use dust collector bags to contain material inside the dust collector box have been shown to provide better protection to roof bolter operators than dust collectors that do not use the bags [Listak and Beck 2008]. The dry collectors are very efficient at reducing respirable coal mine dust exposure from roof bolting activities. Recently, Blue Mountain Energy’s Deserado underground coal mining operation, outside Rangely, CO, made a modification to the dry collector system to convert it to a wet collector system with a unique exception from the Mine Safety and Health Administration (MSHA) for testing purposes. The wet collector system still uses a vacuum system to pull material from the vertical roof bolt hole, but incorporates a water spray nozzle located inside the dust box to wet the incoming material. The flow through the nozzle ranges from 1.9–7.6 lpm (0.5–2.0 gpm) at 0.69 MPa (100 psi). The conversion to the wet collector system removes the precleaner and the cyclones inside the dust box. The wet material (sludge) then empties through a specialized valve in the bottom of the box. The final filter is still used to prevent respirable dust from leaving the dust box through the exhaust. During operation, the wet collector dust box is opened and hosed clean after roof bolting every place. After every two entries the final filter is changed out. Figure 2 shows the inside of the wet collector box.

Jan 1, 2019

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper examines the effect of bucket geometry (cutting blade profile, floor profile, and blade thickness), speed, motor power output, and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scaled model of a load-haul-dump in full factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated to penetration and draft; muckpile particle size is positively correlated to penetration and negatively correlated to draft (p < 0.0014). The results show that buckets with a semi-spade cutting nose profile yield the highest penetration (mean 118.30 mm) followed by those with the spade (mean 108.88 mm), which also yield higher penetration than those straight blades (mean 95.19 mm). Bucket floor profile and blade thickness had no significant effect on penetration or draft. Also, we determined that increasing the speed and motor power output, simultaneously, can reduce bucket penetration. Thus, operators should not waste energy for no additional gain or even loss in bucket penetration. Also, the work finds speed and motor power output each combine with muckpile particle sizes to affect bucket penetration. This research furthers our understanding of the effectiveness of different bucket geometries in improving penetration and reducing draft for rubber tire loaders.

Oct 29, 2021

By D. Newman

Ground control is critical to the success of a safe and productive underground stone mining operation. The primary focus of the ground control engineer is the stability of the roof or back; development and benched pillar stability; stability of the sill pillar between vertically adjacent mining levels; and floor stability. Roof stability begins with the selection of a stable back horizon based on the presence of a thin shale parting, stylolite or other discontinuity from which the production shot can easily peel away, leaving a stable back stratum. Bed thickness, fracture spacing, jointing and the material properties of the roof strata control the room width; the decision whether to bolt the roof; the bolt length, type and diameter; and the spacing of the roof support. Horizontal stress controls the header and crosscut azimuth. The mine operator should avoid driving perpendicular to the maximum horizontal stress direction. Where this is unavoidable, narrowing the opening width, narrowing pillar centers, increasing the support density and using three-way intersections are alternatives to remediate shearing along the roof-rib interface. Stable pillar dimensions depend upon the interaction of the vertical stress resulting from overburden thickness and multiple-level interaction of overlying level or levels; the mining height during development and the final mining height after floor shots are taken during benching; the presence of faults, folds or joints passing through the pillar; and limestone lithology, recognizing that the presence of oolitic bands, shale partings, joints and bentonite beds creates zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone typically exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture-sensitive strata, weak stone bands or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. To illustrate these ground control issues, this paper presents four case histories that are a mix of ground failures and successful mining. The focus is on the geotechnical data required for roof, pillar and floor design and stability analysis.

Jan 8, 2017

By Keith Olson

In the heart of Appalachia, where coal mining has shaped communities and economies for generations, Bluefield State University (BSU) has made a landmark decision to reestablish its mining engineering technology program. This move comes at a critical juncture for both the university and the mining industry, which faces significant workforce challenges amid evolving technological demands and an aging professional demographic. The program’s revival represents an educational initiative and a strategic response to industry needs and regional economic development. Nestled in the mountains of southern West Virginia, BSU has a storied history intertwined with the region’s mining heritage. The institution’s decision to bring back this specialized program after a hiatus of several years signals a renewed commitment to serving both regional industry demands and providing career pathways for students in an area where the cyclical nature of resource extraction economies has often limited economic opportunities. “This program’s return reflects our deep understanding of this region’s needs and our commitment to preparing graduates for meaningful careers that support our local industries,” said Darrin Martin, president of Bluefield State University. “We’re bridging the gap between education and industry with a modernized curriculum that addresses today’s mining challenges while preparing for tomorrow’s innovations.”

Jun 1, 2025

By Paul W. McGann

This paper presents a methodology for long-range studies of petroleum supply, to meet projected demands, that involves modifications of procedures used previously. This paper continues a series of papers on this general topic in the AIME, the most elaborate recent one being that by Warren Davis given in February 1958. The procedures considered here begin with the assumption that the governmental framework of regulations and taxes remains fixed- but that price changes. After .these procedures have been reviewed, the effects of changing certain governmental controls, will be considered in order to judge their potential effects on future supply. This is an essential step because controls cannot be expected to&apos; remain static in a situation changing as much as the petroleum. industry and because such changes are within-the scope of alternative ways of adjusting to impending problems. The first procedure begins with: a) trends in drilling success, b) relation between field income from oil and gas and footage drilled, c) declines in capacity from production, d) trends in capacity of new and producing wells, e) all monetary values are in constant 1958 dollars, and f) target amounts of domestic crude petroleum production. &apos;From these components projections are obtained of: 1) numbers of future producing wells required, 2) footage drilled, 3) new wells drilled, 4) crude oil found, 5) capacity of producing wells, 6) completion costs, 7) finding costs, 8) production costs, and 9) average wellhead crude oil price consistent with the footage-field income relationship.

Jan 1, 1960

By S. J. Page

The personal dust monitor (PDM) is a combined tapered element oscillating microbalance (TEOM) respirable dust monitor and cap lamp, configured to have dimensions and weight similar to those of a lead-acid miner’s cap lamp battery. The Higgins-Dewell (HD) cyclone design operated at 2.2 L min-1 airflow has previously been reported to have low bias relative to the International Organization for Standardization (ISO) convention. Previous reports have described the PDM as meeting the NIOSH Accuracy Criterion. In order to avoid certain analysis anomalies encountered during these evaluations, a different method of establishing the PDM relative standard deviation was employed. Re-analysis of laboratory data for both the early prototype and precommercial PDMs indicates that the PDM still meets the NIOSH accuracy criterion, and that the precommercial PDMs are more accurate than previously reported.

Jan 1, 2011

By Fitzhugh T. Lee

Results from the first part of a two-part investigation of the stability of highwalls in open-pit coal mines in the Paleocene Fort Union Formation of the western Powder River Basin of Wyoming and Montana indicate that these highwalls are subject to time-dependent deformation. Field investigations and laboratory physical properties tests of coal and overburden rocks suggest that several factors influence highwall stability. Some of these factors are rebound of overconsolidated rocks, desiccation, water, orientation and spacing of fractures, and strength and deformation properties. Factors of safety for a typical highwall in the study area (calculated by the finite element method) may be less than 1.0 when open fractures are present and the highwall has degraded. Although it is concluded that most open-pit highwalls in the Fort Union Formation within the study area have adequate short-term stability, these highwalls do deteriorate and become progressively less stable. Because of this, postmining failures are common and stability conditions could become critical if mining were delayed and then resumed after a period of several months. The second part of the investigation will utilize field measurements of rock-mass properties and instrumentation of actively mined highwalls to obtain data for comparison with the results of the initial investigation. Because the height of highwalls will increase as the more shallow coal is exhausted, these data will also be used to predict the behavior of slopes higher than those presently found in the western Powder River Basin.

Jan 1, 1977

By Fiona M. Doyle Garner

Hydrolytic stripping is the process whereby metal ions in a loaded solvent extractant are hydrolyzed by water, typically at 130°-200°C. Equilibrium hydrolytic stripping tests were done on Versatic 10 solutions of various metals, singly and in mixtures. Single solutions of Fe, Xi, Cu, Mg, and tin precipitated aFe2O3, Ni(OH)2, Cu2O, Mg(OH) 2 and ?Mn203 respectively during hydrolytic stripping. Several mixtures containing iron precipitated magnetic spinel ferrites, MFe20k. No other combinations formed mixed oxides. It is proposed that the mechanisms for hydrolysis and precipitation of iron in loaded Versa- tic solutions are similar to those for iron hydrolysis in aqueous solutions. Infrared spec- troscopy and thin-layer chromatography of mixed iron-nickel Versatic solutions indicated that mixed Fe-Ni carboxylate complexes are present. Magnetic interactions between mixed complexes are thought to be responsible for the homogeneous nucleation of magnetic mixed oxides in preference to single oxides.

Jan 1, 1984

By Justin Cardwell, Alyson Cartwright

"Grade estimation is the cornerstone of longrange mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model.Certain deposits, such as the sedimenthosted deposits at Tenke-Fungurume, require an interpolation method that best suits the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the nonstationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface.Geology overview. The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Fig. 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Fig. 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006)."

Jan 1, 2015

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By Julián M. Ortiz, Antoine Caté, Oy Leuangthong, Ilkay S. Cevik

Mineral resource classification relies on the expert assessment of a qualified person (QP) to determine which blocks of a 3D mineral resource model are classified as measured, indicated, or inferred. The decision is often based on a combination of quantitative parameters related to the estimation process and qualitative decisions based on previous experience or preconceptions not captured in the numerical model. As such, the procedure is subject to inconsistency, that is, blocks with similar qualities may end up in different categories, mainly due to the subjective nature of the approach. In this paper, we present a methodology to assist the qualified person in this task by clustering blocks with similar parameters and then classifying them into categories in a consistent and automatic manner that only requires the specification of a few hyper-parameters. The result is a consistent classification into resource categories comparable to the result of a classification done by a qualified person but fully consistent and generated in a short time frame. The procedure begins with repeatedly sub-sampling the block model to determine a distance matrix using an unsupervised random forest approach and then clustering the blocks using the associated distance matrix. Then, all the blocks in the model are classified using a supervised random forest approach, which gives a probability of belonging to each class. The initial class can be determined from the class probabilities. Support vector classification with a radial basis function kernel is utilized to smooth the boundaries between classes and define the final classification. An approach to tune the hyper-parameters of smoothing is provided. The methodology is demonstrated with two examples from two gold deposits. Results are comparable to the classification done by the project qualified person using conventional methods.

Aug 17, 2021