Search Documents

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Solomon J. Salat

During the major expansion of the Inspiration smelter, which took place in 1973, the bulk material handling system underwent a matching expansion in order to move the required materials. Inspiration is the first smelter worldwide to employ electric smelting in conjunction with the use of Hoboken converters (1), (2). The installation includes a 51 -MVA electric furnace, five 4.25m (14-foot) diameter Hoboken converters, rotary dryer, bedding plant, acid plant, heat recovery steam plant, and gas and dust handling system. See Figure 1, Plot Plan. As of today, the 51-MVA electric furnace is the world's largest in the smelting of copper. Engineering design for the installation was per- formed by Treadwell Corporation of New York. The task of designing the conveyor system was complex because the system had to be installed while the smelter was operating and with minimum plant shutdowns, and it had to serve both the existing and the new smelter. Existing conveyors were redesigned where necessary and incorporated into the new conveyor system. See Figure 2, Flow Sheet. The system encompasses the handling of such diverse materials as wet and dry copper concentrates, cement copper, silica flux, cold dope, and concentrate and flue dust.

Jan 1, 1979

By Dean Newman, Michael Behrens, Mark Trim, Justin Arifin

Road tunnels in recent infrastructure projects in Sydney, Australia, are designed to have a fire resistance level of either a 4-hour cellulosic fire or a 2-hour hydrocarbon fire. Where permanent ground support for tunnels consists of systematic rock bolts and relatively thin layer of shotcrete, it is important to ensure that during and after the fire event the ground support is designed/predicted not to pose risks to the tunnel occupant. The global behavior of the ground support can be predicted using finite element analysis, and its resistance is derived with consideration of the material strength degradation due to the elevated temperature.

Dec 1, 2022

By A. A. Compoli

Injecting water under pressure to wet the coalbed in advance of mining reduces mining-generated respirable dust. Owing to economic and geological barriers, water infusion for longwall dust control in the United States is currently limited to the Pocahontas No.3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob gas boreholes. Currently, 43% of the 72longwall mines in the United States employ vertical gob gas boreholes. Computer coalbed reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water infusion system for longwall dust control in the Pocahontas No.3 Coalbed.

Jan 1, 1995

By E. Oraby, S. Garcia, A. Thurgood, D. Bertoldi, G. O’Malley

Mining and Process Solutions (MPS) most advanced process, GlyCatTM is the only process that can be easily adapted to existing cyanidation plants in the market today whose real advantages over cyanidation are when treating copper containing ores, concentrates or tailings. With such complex material, GlyCatTM requires 70-90% less cyanide addition to achieve the same precious metal extraction. However, GlyCatTM is not simply cyanidation with added glycine. It is a completely different process where the solution chemistry and conditions needed to effectively leach the precious metals are quite different. Downstream however, the process is largely unchanged as the recovery of the leached gold and silver uses existing known processes such as conventional activated carbon or zinc cementation (Merrill-Crowe process). Another advantage is lower SCN, OCN, WAD and no free cyanide in the effluent which can substantially reduce cyanide detoxification requirements and decrease the OHS and ESG risk of the operation. This paper outline some of these differences and presents testwork, piloting and process examples to highlight the advantageous of this new process over conventional cyanidation.

Feb 1, 2023

By William Gleason

From Nov. 16-20, the Extraction 2025 Conference will be presented in Phoenix, AZ. The unique conference brings together the 12th International Copper Conference, the 6th International Symposium on Nickel and Cobalt as well as cross-cutting symposia. Extraction 2025 is co-organized by The Metallurgy and Materials Society (MetSoc) of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM), the Society for Mining, Metallurgy & Exploration (SME) and The Minerals, Metals & Materials Society (TMS). The previous, and first Extraction meeting (Extraction 2018) was held jointly by these three societies seven years ago in Ottawa and was a huge success with more than 90 percent of respondents indicating interest in attending a future event. Kimberly Mills, senior process engineer at Samuel Engineering, is the lead for SME. “This installment of Extraction is featuring Copper 2025, Nickel-Cobalt 2025 as well as crosscutting symposia,” said Mills. “All three societies participate on the International Organizing Committee for the Copper Conference Series and are well situated to host this event together. TMS is also hosting the Ni-Co conference this year and agreed to include it as part of Extraction. There are many aspects that can be shared between these commodities to share information on processing technologies and to learn from each other.” SME is the overall conference chair and running the logistical aspects of the event, which includes managing all aspects of the venue and the registration system as well as tours and short courses, Mills said. “SME has many dedicated members serving in various capacities on organizing and programming committees, including Nick Gow serving as Technical Committee Co-Chair for Copper and Adam House assisting on the Copper IOC.” When Extraction 2025 kicks off, it will be focused on the metals needed for the global energy transition with a special focus on copper and nickel-cobalt. “With as rapidly as the industry is changing and the huge demands for these metals we have some serious challenges ahead of us,” Mills explained. “These challenges require collaboration, creative solutions and engaging experts, both inside and outside of our fields, with a push for sustainable sourcing, ethical supply chains, environmental and social responsibility.” The International Copper Conference was started in 1987 as a collaboration between the Institute of Mining Engineers of Chile (IIMCH) and MetSoc of the CIM. The event is typically held every four years and has always been held as a standalone or headlining event at a society annual meeting, said Mills. “Over the years, this conference series alone has brought together members of IIMCH, MetSoc, TMS, SME, the Society for Metallurgists and Miners from Germany (GDMB), the Mining and Materials Processing Institute of Japan (MMIJ), the South African Institute of Mining and Metallurgy (SAIMM) and the Nonferrous Metals Society of China (NFSOC),” she added. “Being a part of Extraction allows for even more sharing of ideas and expansion of networking. This conference has not been held in the United

Oct 1, 2025

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By Vladimir J. Ovdenko, Sergey N. Lazarenko, Evgeny L. Schastlivtsev

The term sustainable development shortly appeared in international use in the run of UNO Environmental Protection Conference held in Rio de Janeim in 1992, bears the concept, that evolution process ( associated either with a region or society) should provide mutual interests concern in three aspects - environmental, economic and social ones, admitting as well the fact , that environmental protection should become an integral part of each process and cannot be regarded separately. In this connection it seems quite reasonable to employ the principal of sustainable development, while creating the model of industrial mastering the territory constraint lands viewing their future, for a example, in rich mineral deposit's development. In Kuznetsk coal basin in Russia ( west Siberia) the development of a big coal deposit Erunakovsky is now being underway. The major part of coal will be mined with open cast method, resulting the number of local environmental adverse impacts' occurrence. In such a situation mastering of sustainable development model is given the top priority, demonstrating the essential result of its application in a form of possibility to define the best correlation between economically expedient and environmentally tolerable loads during coal mining. The given paper is an attempt to work out the main principals to approach the creation of sustainable development model in regard of the definite region case. To simplify the presentation of employed approach's main idea, the given below accepts as its component only one of many actually existing environmental profiles, that define mining pro- cess impact on environmental situation -the size of infringed (de- graded) lithosphere surface. Basically, the actually existed correlation between spheres. grounding the model of sustainable development - economic, environmental and social- is given in a form of nomogram under Fig.1. On the presented graph the prognostic values of broken lands relative extent within Erunakovsky boundary ( to be compared with total region area taken as 100%) are arranged on axis x". Axis "y- demonstrates the main values associated with complete economic background, making the intrinsic part of the principal for sustainable development, i.e. annual coal output for the given area. It's top, used in assessment value relates to actual showings implied for the study region project and quantifies 60 min. tons. While regarding the social facet of principal for sustainable development, the applied mode to separate social issues into two types - one profiling a welfare standard of living and the other. pertaining the way environmental situation contributes to the degree of &ologica-1 comfort in people's living was defined as the most expedient and the most adequate in the matter of reflecting the actual terms of vital activity of the society. In accordance with the cited above the economic level showings are plotted on the graph on "-x” axis, while "-y" one obtains the values associated with the point of ecological comfort presented in conventional units. For the maximum possible conventional point of living (corresponding in nomogram to 1.0 value) a welfare level secured with industrial region economic activity revenue was assumed in case the top planned annual amount of coal is delivered ( 60 min. tons). While studying the index of public economic welfare, environmental conditions corresponding level in its original state i.e. prior to any industrial work carried in the region, was adopted as its top possible conventional rating (1.0). The given nomogram displays the integrity of x-f(y) type interrelations plotted on the basis of four separate dependencies, precisely a) the size (area) of infringed earth's surface as a function of coal output in the region; b) subordination of ecological comfort of people's living to the degree of lands infringement; c) interconnection of economic and environmental components of people living; d) interconnection of economic level of people's living and the amount of coal mined in the region. Linked to a single unit, these separate plain dependencies create, as seen from the graph, a more intricate system of bonds, that affords during defining or changing this or that system parameter to secure undergoing changes, that occur to other parameters of the system. The mentioned reason made it possible to consider and drive to mutual conformity ( as far as it is possible) all parameters values for the defined system's relations, that in their turn indicate the concern of other aspects of a sustainable development principal. According to the graph, in order to get not more than 50% of infringed land left after the deposit's mining, it is advisable to ex- tract not more than 40 min. tons of coal annually, gaining in this case the level of ecological comfort for living in the amount of not

Jan 1, 1996

By M. L. Free, N. Dhawan, M. S. Safarzadeh, J. D. Miller, M. S. Moats

"The drum agglomeration of nickel laterite and gold ores has been optimized through the design of experiments (DOE) using a Taguchi L16 (45) orthogonal array to determine the optimum conditions for maximizing average agglomerate size and minimizing the amount of fines. The effects of controllable operating factors including moisture content (nickel laterite ore: 34-37%; gold ore: 7-10%), retention time (2-3.5 min), drum speed (15-45% critical speed), drum load (nickel laterite ore: 8-32 %; gold ore: 6-22%) and acid concentration (150-600 g/L) on the performance of the agglomeration process were studied.For nickel laterite ore, maximum average agglomerate size and minimum percent fines (-1 mm) occurred under the following conditions: drum load (23.7%), moisture (36.5%), time (3 min), drum speed (30% critical speed) and acid concentration (150 g/L). Under the studied nickel laterite ore conditions, the most effective parameters for maximizing average agglomerate size and minimizing the amount of fines were found to be drum load and acid concentration, respectively. Drum speed had a statistically significant effect on minimizing the amount of fines. Maximum average agglomerate size and minimum percent fines (-1 mm) for gold ore occurred under the following conditions: drum load (19.3%), moisture (8.5%), time (2 min 15 s) and drum speed (40% critical). The most significant factors for maximizing average agglomerate size and minimizing the amount of fines for gold ore were found to be drum load, time and moisture.IntroductionSeveral heap leach operations have experienced problems in terms of poor recovery due to percolation issues caused by low-grade complex ores, tailings and clayey deposits. Poor percolation can lead to low metal extraction due to solution channeling or the development of impermeable/dead zones within the heap (Dhawan et al., 2012; Kappes, 2005). Improper heap building practices such as the use of loose agglomerates and inadequate attention toward the presence of clay minerals have been among the main reasons for percolation issues. During the transport of ore material, severe segregation of the material can occur. To overcome percolation problems, a major improvement was made through the introduction of agglomeration prior to ore placement. If the ore particles and agglomerates are of similar size, segregation can be avoided to a great extent (Dhawan et al., 2013; Kinard and Schweizer, 1987; McClelland and van Zyl, 1988). Agglomeration improves the uniform percolation of solution through ore heaps and is applicable to many ores, wastes and milled tailings (Bouffard, 2005; Dhawan et al., 2013). Manning and Kappes (2005) reported agglomeration/ stacking accounts for ~14% of the total heap leaching operating cost. The cost of binder is a primary contributor toward the total cost. Also, the lack of consistent quality control tests for agglomerate often leads to operational problems. The details are mentioned elsewhere (Dhawan et al., 2013). Considering the significant contribution of the agglomeration/stacking step toward the total heap leach operating cost, it is appropriate to study the agglomeration behavior and its optimization for two different ores. The reason to study the same parameters for different ores is the fact that significant variability in the agglomeration behavior of different ores has been reported to exist in industrial operations."

Jan 1, 2015

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By Katerina Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate the media wear but also adversely affect the flotation response of the sulfide mineral. A possibility of remedying the adverse effect on its floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy and x-ray photoelectron spectroscopy were used to study the surface properties of pyrrhotite. Although anodic polarization of the steels increased the metal loss by corrosion, the flotation recovery of pyrrhotite was increased. In the case of cathodic polarization, the flotation recovery improved in a narrow range of overpotentials. At higher cathodic overpotentials, however, the floatability of the mineral was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1984

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By A. D. Hammond

Vanadium is a transition metal, ductile, silver-gray metal. It is harder than most metals and steels and it has a good resistance to corrosion, it is stable against alkalis, sulfuric and hydrochloric acids. Vanadium is oxidized in air about 660 °C, although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states 2-5. In aqueous solution the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called, roscoelite K(V3+,Al,Mg)[(Si,Al)4O10](OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world's vanadium mine production comes from magnetite-hosted deposit and to a lesser extent, in sedimentary-hosted sandstone. Vanadium is also present in bauxite and in fossil fuel deposits such as crude oil, coal, oil shale and tar sands. In crude oil, concentrations up to 1,200 ppm have been reported. A significant vanadium production comes from the processing of petroleum residues, fly ash and recycling spent catalysts. In 2011, metallurgical applications accounted for 93% of the use of vanadium. Here, an alloy called ferrovanadium is utilized to strengthen steel to be used as rebar in the construction industry, in the manufacturing of axles, crankshafts, gears and chassis in the automotive and transportation industries and in the manufacturing of high-speed tools. In the aerospace industry, vanadium is utilized as a titanium alloy in the manufacturing of airframes and jet engines. The reason for the wide use of vanadium as alloy is its high strength-to-weight ratio, the highest of any engineered material on earth. The major non-metallurgical use of vanadium is in the production of catalysts for the chemical industry. The most commercially important compound is vanadium pentoxide (V2O5), which is used as catalyst in the production of sulfuric acid.

Feb 23, 2014

By A. Iannacchione

Most legacy drift mines entered the coal reserve from outcrop and developed up-dip. The Surface Mining Control and Reclamation Act of 1977 changed this way of mining, requiring all new mines with acid- or iron-producing coal seams to be designed so as to prevent gravity water discharges from the mine. This Act requires engineered barriers to contain the mine pool. In many cases, mine layout designs focus primarily on the size and hydraulic performance of the un-mined coal barrier between the up-dip mine pool and areas where down-dip surface discharge is possible. In other cases, designs focus on preventing discharges from barriers contained within the strata surrounding the mined coalbed. This paper focuses on a detailed analysis of the factors responsible for preventing mine pool discharges to surface waters. Important factors include: mine layouts, mining methods, hydraulic head and conductivity, and geology. While the exact causes for the successes and failures could not always be determined, reasonable mechanisms are presented.

Feb 23, 2014

By Edward S. Hsia

Pluor Utah has been closely associated with the engineering and construction of earth bottom thickeners for porphyry copper operations, for the counter-current decantation circuit of a gold cyanide plant and similar applications in mineral processing. During the past 13 years, some 18 of these thickeners have entered service and the bottoms have proved to be watertight structures with no particular problems encountered. In the course of this work, technological advances have been realized in the procedures for engineering and construction of these units to assure watertight basins and achieve all possible economies in construction. This paper describes the successful application of engineering and construction techniques for a number of these thickeners.

Jan 1, 1977

By V. A. Mironenko

The combined study of ground water regime and rock deformations has resulted in the theoretical substantiation of the common principles for analysis of the hydrodynamic and geomechanical processes Within the scope of unique scientific direction -hydrogeomechanics (Mironenko and Shestakov, 1974). The hydrogeomechanical models are widely used now for the analysis and forecasting the extremely important processes connected with the safe and efficient mining operations, as well as with the protection of geological medium. Among these processes are: -deformations of the open-pit slopes and spoil dumps; -consolidation of rocks due to the ground-water pressure drop; -water-end-rock material inrush into mine workings caused by deformations of the undermined rock mass; -geodynamical processes due to the changes in ground water regime; -artificial hydrofracturing in rocks; -transformations of clay linings under the tailing ponds and other technical water basins.

Jan 1, 1990

By L. G. Hagenbuch

Several factors need to come together in creating an integrate mining equipment dispatching system. At the hub of these factors ace the central dispatching formulas. This paper details the development of these central dispatching formulas and explores the combining of these formulas with other elements to create an integrated dispatching decision. WHY DISPATCHING? Truck dispatching implies and in reality should equate to mine equipment efficiency. Good truck dispatching will yield good mine equipment efficiency while poor truck dispatching will yield the alternative. Truck dispatching can either be automated through a computerized, process or it can be manual. Every mine with haul trucks has a truck dispatching system whether it is recognized or not. Even a system wherein the hauler operators determine where they are going for their next load is a truck dispatching system.

Jan 1, 1987

By V. T. McLemore

"Lindgren (1933) defined a belt of alkaline-igneous rocks associated with large quantities of gold and rare earth elements (REE) that extends from Alaska and British Columbia southward into New Mexico, Texas and eastern Mexico. The North American Cordilleran alkaline-igneous belt since has been exploited for numerous types of mineral deposits. In New Mexico, Mid-Tertiary alkaline to calc-alkaline rocks are found with seven types of deposits in these districts: (1) polymetallic epithermal/mesothermal veins, (2) gold-bearing breccias/quartz veins, (3) Cu-Au, Au and Mo porphyry deposits, (4) skarns and carbonate-hosted deposits, (5) iron skarns and replacement bodies (with some gold), (6) gold placers, and (7) Th-REE (with some U, Nb) epithermal veins. Some of New Mexico’s largest gold and REE deposits are found within this belt. Their origin is not well understood, but a compilation of new data (age dates, isotopic and chemical analyses) allows for a better understanding. The diversity of igneous rocks and associated mineral deposits along this belt suggests that this region is characterized by highly fractionated and differentiated; multiple pulses of magmas and involves both upper mantle and lower crustal sources. Once magmas and metal-rich fluids reached shallow levels, local structures and wall rock compositions determined distribution of and final style of intrusions and resulting mineral deposits. INTRODUCTION Lindgren (1933) was one of the first geologists who noted that a belt of alkaline-igneous rocks extends from Alaska and British Columbia southward into New Mexico, Trans-Pecos Texas, and eastern Mexico (Fig. 1) and that these rocks contain relatively large quantities of gold, fluorine, zirconium, rare earth elements (REE), and other elements. Since then, the North American Cordilleran alkaline-igneous belt has been explored and exploited for numerous types of mineral deposits, especially gold. The North American Cordilleran alkaline belt is a north-south belt of alkaline igneous rocks and crustal thickening, roughly coinciding with the Great Plains physiographic margin with the Basin and Range (Rio Grande rift) and Rocky Mountains physiographic provinces (Mutschler et al., 1985, 1991; Bonham, 1988; Thompson, 1991a; Richards, 1995; McLemore, 1996; Jensen and Barton, 2000; Kelley and Luddington, 2002). Deposits within this belt have produced significant amounts of gold in the United States and Canada and include Cripple Creek, Colorado (702 metric tons of gold production), Black Hills, South Dakota (235 metric tons gold production) and Landsky-Zortman, Montana. In New Mexico, the North American Cordilleran alkaline belt extends from the Sangre de Cristo Mountains near Raton, southward to the Cornudas Mountains, in the northern Trans-Pecos alkaline belt (Fig. 2). The alkaline-igneous related mineral deposits in New Mexico have been referred to as Great Plains Margin (GPM) deposits by North and McLemore (1986, 1988) and McLemore (1996, 2001). Alternative classifications by other workers include Au-Ag-Te veins (Cox and Bagby, 1986; Bliss et al., 1992; Kelley et al., 1998), alkalic-gold or alkaline-igneous related gold deposits (Fulp and Woodward, 1991a; Thompson, 1991a, b; Bonham, 1988; Mutschler et al., 1985, 1991; Richards, 1995), porphyry gold deposits, and the North American Cordilleran belt of alkaline igneous rocks (Woolley, 1987; Mutschler et al., 1991)."

Jan 1, 2015

By Jr. Watts

The American Mining Congress and the U.S. Bureau of Mines have formed a collaborative research team to develop, implement, and evaluate a comprehensive control strategy to reduce diesel particulate matter concentrations without degrading other air quality parameters at an underground noncoal mine. Other participating organizations include Caterpillar, Inc., the Mine Safety and Health Administration, and the University of Minnesota. After extensive baseline information and air quality data are collected, available control strategies to reduce diesel particulate matter exposures will be implemented, individually or in combination, and evaluated. This paper discusses the objectives and protocol of the collaborative effort to evaluate diesel particulate control technology.

Jan 1, 1995