Search Documents

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By R. E. J. Putman

The, principle purpose of applying control to any process is to improve -its profitability. Even when considering the impact of a plant on its surrounding ecology this is still, true, since the sanctions felt most immediately from violations of the regulations are the economic penalties or fines which result. 'Economic performance can be improved within a plant in several ways. Steps can be taken to cut the cost or quantity of resources (power, water, steam, reagents) consumed per ton of throughput. Alternatively the operation of the plant can be changed so as to increase product yield per ton of throughput. Or the cost of labor and plant overhead per ton of product can be reduced by raising the total 'throughput, assuming-that the increased amount of product can be sold for the same unit price. In designing a program to improve plant performance, all three routes should be borne in mind. To maximize the return on investment over a longer period, it is also desirable to set up a comprehensive plan of improvement, equipment being specified at each step in the implementation so as to ensure that it fits in with later requirements later implementation being either by means of modular additions or by having the necessary interfaces built into the original equipment. It is much cheaper in the long run to buy features which have been factory-installed, than to have to make provision for their later addition in the field. This paper examines some ways of improving plant performance by the application of various process control techniques using both analog and digital con¬trol equipment. A general philosophy of application is suggested and specific examples described.

Jan 1, 1972

By O. Ozdemir

Soda ash, an essential raw material for major industries, such as the glass, chemicals, soap and detergents, pulp and paper, mining and water treatment industries, is traditionally produced by chemical and thermal treatment of trona ore. The treatment processes for trona ore are not only chemically expensive but also energy intensive. Hence, the production of a high-purity trona concentrate at a lower energy and operating cost is of considerable interest to the trona industry. In this study, we describe a possible two-stage process for concentrating trona ore, involving dry magnetic separation followed by flotation, to remove insoluble impurities from the trona ore. The results showed that a trona concentrate of 91.7% purity with a recovery 91.1% can be obtained by two-stage magnetic separation, which could be further improved to 98.1% purity at a recovery of 83.8% by subsequent flotation of the non-magnetic trona product. The purity of trona concentrate is limited by the particle size and impurity content of the trona ore. The operating parameters for magnetic separation and flotation have been identified to obtain an acceptable quality concentrate.

Jan 1, 2011

By Tuncel M. Yegulalp

This article summarizes some of the results of the continuing research activity at the Henry Krumb School of Mines, Columbia University, directed towards a better understanding of the stochastic behavior of slurry flows in underground coal-slurry pipeline systems. The slurry system under consideration here replaces all conventional haulage systems between the coal face and the coal preparation plant on the surface. At the beginning of the pipeline system, flow rate and frequency of coal slurry is very closely related to the activities of production equipment at the coal face. Due to several scheduled and unscheduled interruptions in continuous miner's coal mining activity, resulting slurry flows possess stochastic characteristics. Proper understanding of these characteristics is believed to lead to a more realissic and economic design of slurry handling equipment. Fundamental ideas supported by field observations are presented and a Semi-Markov model of the slurry flows is developed. As a result of this formulation, behavior of combined slurry flows from N independent coal faces can be expressed in analytical form. The contents of a slurry surge tank receiving slurry flows with certain stochastic characteristics is investigated as a function of discharge pump characteristics and time.

Jan 1, 1981

By John E. Frost

Duval's (now Battle Mountain Gold Co.) copper and gold deposits in the Battle Mountain District in Nevada are in two subdistricts - Copper Basin and Copper Canyon - about 18 km (11miles) apart. Location of the two subdistricts is shown in Fig. 1. The two centers of mineralization have distinctive geologic and ore characteristics that required different innovative approaches to exploration and development. Nearly all of the copper from Copper Basin has been recovered by heap leaching. Because of relatively high gold and silver values in the Copper Canyon ores, a significant part of the sulfide copper ores has been recovered by a conventional flotation mill at Copper Canyon. Recently, this mill has been converted to the recovery of gold that is mined from zones peripheral to the copper deposits. Prior to Duval's entry, small amounts of copper, gold, silver, lead, zinc, and antimony had been mined in the district over a nearly 100 year period, beginning in 1866. The bulk of the $13 million total production to 1962 was derived from copper and gold lode ores and gold placers. Duval's interest in Battle Mountain-arose directly from a submittal by Asarco, which controlled key claims in both the Copper Basin and Copper Canyon subdistricts. Asarco acquired its holdings in the district in 1959 and undertook limited exploration until mid-1961. At that time, the company decided to dispose of its interests. Duval was invited to evaluate Asarco's properties and accepted. On Dec. 6 and 7, 1961, J.E. Frost, R.C. James, R.W. Sayers, and H.A. Schmitt, representing Duval, and K. Richard and E.W. New- man, representing Asarco, visited Copper Basin and Copper Canyon. Frost concluded that the properties were of considerable interest and prepared, by Jan. 12, 1962, a voluminous report recommending that Duval acquire and explore Asarco's properties. Furthermore, he recommended a large initial exploration program that included not only geologic mapping, geochemistry, and geophysics, but also the extensive drilling that was to involve, as the first phase of exploration, 49 drill holes in Copper Basin and 21 drill holes in Copper Canyon. Following property agreements between Duval and Asarco, and Duval and several other claim owners, geologic mapping, geochemical surveys, and drilling began in August 1962. Exploration drilling was completed in July 1964 and engineering studies in April 1965. Development of the Battle Mountain properties was authorized in July 1965, and production commenced in the first quarter of 1967. Because of the unusually high oxide copper content of the ore bodies, particularly in Copper Basin, a much larger than typical proportion of the copper in the deposits has been recovered by heap leaching. The generalized geology and ore zones of the Copper Basin are as shown in Fig. 2 and of Copper Canyon in Fig. 3.

Jan 1, 1991

By B. J. Huls

The commissioning of a Distributed Digital Control. System for the grinding circuit at Cuajone, was completed by mid August, 1985. Development of a successful strategy, excellent operator acceptability and the visual aspects offered by the display of the central console, improved mill throughput significantly. The inherent features of a digital system enhanced the flexibility in grinding control and allowed the mills and classifiers to be operated at maximum capacity. This paper discusses in detail the strategy development, the production restrictions encountered, and evaluates the overall performance of the digital control system. 1.0 Introduction In November 1976, the Cuajone Concentrator, located on the western slope of the Andes in Southern Peru, was commissioned to treat a nominal 41,000 TPD of ore. A systematic elimination of production restrictions has resulted in a continual increase of concentrator throughput to 48,700 TPD before the grinding control was in- stalled.

Jan 1, 1986

By D. B. Gentzler, J. L. Kohler

A method of monitoring production information (raw tonnage and machine state) from each working section has been developed. The method is based on the sensing of electrical parameters in each section load center, and the reporting of this information through the existing mine-wide monitoring system. A decision-theoretic type of pattern classification technique has been used to define the machine states. The basis of the method is presented in this paper, along with a proposed hardware and software implementation scheme. Information issues central to the development and use of the proposed production monitoring system are also discussed.

Jan 1, 1990

By S. S. Xue

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipex® extractant, P,P?-di(2-ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 10 6 Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By G. A. Kordosky

There are a number of reasons why the solvent extraction of molybdenum deserves attention: 1. The solvent extraction chemistry of molybdenum is interesting and complex, 2. The price of molybdenum is predicted to average about US$ 20.00 / pound in 2010 and, as China, India and other countries develop, the demand for specialty steels will increase putting long term demands on molybdenum supply, 3. Uranium ores often contain significant concentrations of molybdenum[1] and typically yellow cake will have a moly specification which when exceeded brings penalties, and 4. The valuable metal rhenium is a byproduct of molybdenum recovery circuits.

Jan 1, 2010

By Chao Zhang, Wenhao Xia, Jianxin Fu, Ling Yu, Weidong Song, Yang Li

Sanshandao Gold Mine is the only undersea metal mine in China. To deal with the collapse and pumping of stopes and roadways caused by complex ore-rock occurrence conditions, the mine conducts filling and sealing of some areas, and the remaining ore reserves will be mined after treatment. Therefore, it is urgent to evaluate the stability of rock masses, fault fracture zones, and aquicludes during the secondary mining process. In this study, displacement and microseismic methods are employed to monitor rock deformation and fractures. Additionally, FLAC3D was used to simulate the process of secondary mining, reproducing the evolution of stress fields, displacement fields, seepage fields, and plastic zones at different mining stages. The combination of numerical simulation and on-site monitoring verification demonstrates that the deformation of surrounding rock presents a rapid growth at the initial stage of mining, followed by a gradual decrease in the growth rate, and finally tends to stabilize; the fracture zone area at the 151–159 exploration line on the − 320 m level (near the 7# and 8# stopes) exhibits poor stability, and monitoring measures should be strengthened; the deformation value of the aquiclude is less than the deformation value of I protection level in the Code for Design, the impact of secondary mining on the aquiclude is limited; fault and fracture zone deteriorate rock mass stability, and their impact is related to their spatial locations. Hanging wall fault has a more significant impact on the settlement of the aquiclude, while the footwall fracture zone has a greater impact on the development of the plastic zone.

Feb 21, 2024

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960's. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By W. J. González

With the increasing demand for minerals and the decline in the quality of ore reserves, technologies to maximize recovery are critical to a mine?s economic success. Many mining waters exhibit the potential to form hardness-based inorganic scales, which inhibit effective mineral recovery. Often, a continuously-fed chemical deposit control program is implemented by the mine site to inhibit these scales. The use of retractable scale coupons is the current industry standard for monitoring these programs; however, a key drawback to their use is the limited, and sometimes untimely amount of information they provide. A proprietary fouling analyzer has been developed that can be used to continuously monitor the formation of inorganic scales in mining process streams. Consequently, it can be used to continually, and more effectively, communicate the efficacy of an antiscalant program, thereby providing the ability to compare different scale control programs and to optimize their feedrates. Case studies presented validate the applicability of this technology to help optimize mineral recovery.

Feb 23, 2014

By J. D. Forrester

In striving to develop this discussion about "Manpower for Industrial Mineral Industries" two fundamental classes of manpower are encountered. These are: 1) The Labor Force, comprised of unskilled and semi-skilled, nonprofessional personnel who participate in conducting economic, mineral deposit operations and; 2) The Professional People involved in the science, engineering, and management of such industrial enterprises. The commentary given here will be directed primarily to a review of the characteristics of the second or latter class. To pursue successfully a career as a scientist or engineer in today's industrial and social complex, it is necessary that technical knowledge must have been acquired by training and study in an institution of higher learning. Also, to act effectively, the individual must have achieved some degree of specialzation, although this element often is developed to most notable degree by post-graduate exposure and experience. In addition, and especially in the case of "management," it is desirable, indeed it is even necessary, that an individual recognize and appreciate the fundamental humanistic-sociological controls, and their nuances, as these elements exist to shape his total environment.

Jan 1, 1969

By James L. Evers

The development of hydraulic mining in the United States has had an uneven record of progress. The shifting of coal extraction from one government agency to another has not provided an environment for a focused national research program. This paper presents an update on hydraulic mining research in the United States. A comparison is made between the development of the technology in this country and the state of the art in other parts of the world.

Jan 1, 1983

By C. St. J. Lowe

Weir Minerals ? Linatex has developed a new approach to the dewatering of fine solids, particularly mine and process plant tailings and wastes. The Weir process, patented in 2009, uses standard process equipment in a standard flow sheet, but applies this approach to materials previously thought to be too fine to be dewatered with this type of equipment. The process can be applied to a wide range of materials, making lower moisture products that can be re-used elsewhere or sent to disposal. It has already been tested successfully on a small scale in Australia on coal fines, zinc mine tailings, red mud, iron ore tails, and copper/gold tailings. The principal factors affecting the solids recovery have been established as: 1. The % solids in the slurry feed to the process ? a higher % solids provides a higher recovery. 2. The particle size of the feed solids ? coarser feeds provide higher recoveries. The key factors affecting the % solids in the dewatered product have been determined to be: 1. The particle size of the dewatered product - coarser materials produce a higher % solids in the dewatered product. 2. The height of the discharge weir on the dewatering screen - a higher discharge weir on the dewatering screen also yields a higher % solids. 3. The angle of the dewatering screen. Setting the screen horizontal increases the travel rate, reduces the bed depth and reduces the % solids in the dewatered product. Back-sloping the screen up to 5° reduces the travel rate and increases the % solids in product. Eight plants ranging in size from 3 t/h to 40 t/h have been sold to a range of customers in China, for coal and iron ore tailings treatment. Australia has one plant, a small unit rated at 30 t/h of sand fines, and has recently completed test work on iron ore tailings for a dewatering plant rated at 135 t/h. Additional tests are under way with clients around Australia, to demonstrate the capabilities of this process on specific applications and to provide confirmation that materials can be processed successfully, before moving on to larger scale tests or full size plants. The advantages of the Weir process include - lower moisture in products, uses proven equipment, lower capital and operating costs, lower maintenance costs, reduced power consumption, compact footprint, can be used in parallel or in series with existing equipment, modular design to facilitate redundancy or expansion, efficient water recovery and simpler water management, reduced cement in backfill mixes, smaller tailings disposal footprint, reduced earthworks requirements, much lower seepage losses, more stable tailings mass, progressive site rehabilitation, reduced impact on local wildlife, reduced risk of dam wall failure, and reduced environmental monitoring and compliance costs.

Feb 23, 2014

By Peter Zhang, Todd Minoski, Gabriel Esterhuizen, Jack Trackemas, Berk Tulu, Morgan Sears

Longwall mining is a highly productive and efficient coal mining method used in the USA. During longwall retreating, the belt entry must be maintained stable, and any roof fall in the belt entry would jeopardize mine safety and substantially interrupt the continuous production of coal in the longwall face. Past experience of longwall mining has shown that belt entry stability was the greatest challenge in longwall ground control, and the occurrence of roof falls in belt entries was largely associated with high horizontal stress. To properly support the roof in the belt entry, it is important to understand how longwall-induced horizontal stress changes affect roof stability in belt entries and to strategically install supplementary support to prevent any potential roof falls. Researchers from the National Institute for Occupational Safety and Health (NIOSH) performed horizontal stress measurements in the immediate roof of the belt entries for two Pittsburgh seam longwall panels oriented unfavorably to high horizontal stress. Hollow inclusion cells (HICells) were installed in the immediate roof at the intersection in each of the belt entries, and stress changes were monitored as the longwall face was approaching and passing the intersection. Numerical models were set up to calculate the longwall-induced horizontal stress changes in the roof at the monitoring sites. With the verified model, investigations were made of how horizontal stress is concentrated and relieved in the belt entry roof near the face under different panel orientations. Both measurements and modeling results showed that high horizontal stress is concentrated in the roof in the belt entry within about 15 m outby the face when a longwall panel is unfavorably oriented to the major horizontal stress. The study demonstrated that longwall-induced differential horizontal stress can be used as an indication of the degree of horizontal stress concentration. Roof support strategies are discussed on how to maintain the stability of belt entry under high horizontal stress concentration.

Jun 14, 2022

By R. T. Hukki

The paper describes a two-stage industrial hydraulic classification system including hydrocyclones for primary classification and newly developed cone classifiers for secondary classification. Performance data based on large scale grinding and classification tests are presented.

Jan 1, 1981

By Olivier Martin

In busy and historic cities, traditional open box metro stations are becoming outrageously difficult, unacceptable for the citizen and uneconomical. Hybrid stations provide an interesting alternative. In-house experience of Gautrain (South Africa), West bay (Qatar), Cairo line 3A (Egypt), and Melbourne (Australia) all aim to reduce disturbance to the city and its inhabitants during construction. Constructed in rock or in deep soil under water table, they take advantages of the latest construction techniques from cement grouting to freezing, and from traditional excavation of cavern to large tunnels constructed by sophisticated tunnel boring machines (TBM). Today, they form the ultimate construction challenge.

Jun 13, 2021

By David L. Giles

The Lime Creek* ore body in northwestern British Columbia is one of the few commercial primary stockwork-type molybdenite deposits in North America. Others include the Climax, Urad-Henderson, Questa, and Endako ore bodies. They are mined on a low grade-high tonnage basis, and are open pit operations except for Climax and Urad-Henderson. Much recent geochemical research on both porphyry copper and stockwork MoS2 deposits has been concerned with dating of micas related to the mineralization and associated igneous rocks. The results appear to show that mineralization and the predominant magmatic events of the deposit are indistinguishable in age (1-5), except where dating has been in sufficient detail to resolve the analytical overlap (6). At Lime Creek, geologic information shows that the Main granodiorite, the major intrusive and dominant host rock for MoS2 mineralization, was emplaced and had solidified sometime prior to the introduction of MoS2. The first MoS2 episode is intimately related to localized bodies of kalialaskite which clearly intrude the older stock. K-Ar dating was undertaken to clarify the age relations between Lime Creek plutonism and the apparently younger hydrothermal event that began with kalialaskite.

Jan 1, 1975

By Zhan-fang Cao, Hong Zhong, Li-feng Li, Shuai Wang, Xiao-yu Cao, Guang-yi Liu, Ming-ming Wang

"In recent years, there has been an increasing focus on the hydrometallurgical processing of molybdenite, with the decline of high-grade and easily handled molybdenum minerals. In this work, a novel method of selective extraction of complex molybdenite concentrate, which is characteristic of high-grade copper ore, has been investigated. The results show that the leaching of chalcopyrite was impacted by the pH of the electrolyte when sodium carbonate and ammonium acid carbonate were added to the electrolyte. The leaching rate of molybdenum reached 99.39%, but chalcopyrite could not be leached at all in 240 min under experimental conditions of liquid-to-solid ratio 25:1, concentration of NaCl 4 mol/L, pH=9, room temperature and agitation speed 400 rpm. The grade of copper in the residue was 21.84%, with a recovery 99.93%. The technology of selective electro-oxidation leaching of molybdenum and recovery of copper from complex molybdenite concentrate is an effective separation method. The diffusion control model can be used to describe the process of leaching of molybdenum. The activation energy of the leaching reaction was found to be approximately 9.21 kJ/mol.IntroductionWorldwide, high-grade and easy-to-handle ore is decreasing, while the proportion of low-grade and complex ore is increasing. Porphyry copper ores with associated low-grade molybdenite are very abundant in China. Molybdenum is a valuable byproduct in the processing of porphyry copper deposits where the molybdenum is present in low quantities in the form of molybdenite (MoS2). In the conventional processing of copper sulfide ores by froth flotation, most of the molybdenite in the ore floats along with the copper sulfides. In this way, a bulk copper-molybdenum concentrate is produced. Afterward, the bulk coppermolybdenum concentrate is treated by differential flotation to obtain a rougher molybdenum concentrate, which requires several successive cleaning steps to produce a final molybdenum concentrate. However, it is widely recognized that flotation alone cannot economically produce a high-grade molybdenite concentrate, i.e., with less than 0.5% Cu. Therefore, in most cases, it is necessary to use a final step of chemical purification of the molybdenite concentrate to reduce the copper content to a level suitable for the market (Antonijevic and Pacovic,1992; Gerhardt et al., 2001; Fu and Zhong, 2003; Reza et al., 2006, Rafael et al., 2013)."

Jan 1, 2015