Search Documents

By Jian Liu

The study aims to leach copper from a low-grade flotation middling by optimizing the leaching process using response surface methodology. The effect of key parameters, i.e., sulfuric acid concentration, nitric acid concentration and leaching time, on the leaching efficiency was investigated and a quadratic model was suggested by the methodology to correlate the variables to the efficiency. The results indicate that the model is in good agreement with the experimental data at a correlation coefficient (R2) of 0.97 and the most influential parameter on efficiency was identified as sulfuric acid concentration. The optimum conditions for copper leaching from the middling were identified as sulfuric acid concentration at 103.74 g/L, nitric acid concentration at 12.50 g/L and leaching time of 30.98 min; under such a condition, an average leaching efficiency of 93.16% was achieved from the middling.

Jan 1, 2011

By Owens S. Roberts

The drive selected for any piece of machinery must adequately satisfy the application requirements both during the starting interval and at running conditions, All loading possibilities of the drive must be known and allowances made for any adverse limiting conditions such as extreme cold, or perhaps an intermittent excessive loading situation etc. In general, the drive must be selected to provide the required operating characteristics with maximum reliability and at minimum cost. Simplicity of overall design is always an advantage and care must be exercised to insure that systems incorporating unnecessary complicated parts are not indiscriminantly provided. Important non-technical considerations such as equipment avail-ability (on an overseas project) as well as standardization details also play a role in the drive selection process. Additionally, an assessment of the potential capabilities of the personnel that will have to maintain the equipment can have some influence on the final choice. Several types of prime movers are available but this article will restrict itself to the use of induction motors operating from an available alternating current power source. Many drive arrangements are possible, the most common being the direct coupled single motor arrangement. It is sometimes desirable to use more than one motor per machine, but these designs are usually more

Jan 1, 1971

By Wei Victor Liu, Omer Faruk Ugurlu, Chengkai Fan, Bei Jiang

Accurate prediction of truck productivity plays a pivotal role in improving the efficiency and profitability of openpit mining operations. This paper proposes a deep neural network (DNN) model to overcome the challenge of predicting truck productivity in openpit mines. The prediction model was built using eight variables and was optimized by considering different train-test split ratios, numbers of hidden layers and neurons, and activation functions. The proposed model’s performance was evaluated using various metrics and compared with other commonly used machine learning algorithms. The results showed that the proposed model outperformed traditional machine learning models by achieving higher prediction accuracy. Moreover, a single-variable sensitivity analysis showed that haul distance is the most influential variable for predicting truck productivity. This study marks a pioneering effort in employing DNN to predict truck productivity in openpit mining, signifying a notable advancement in the field.

Jul 1, 2024

By Drew Bazil, David Smith, Matteo Ferrucci, David Pittman

The Gateway program will provide additional rail capacity between New Jersey and Manhattan. This paper describes how a 70-foot-deep section of cut and cover tunnel was designed to directly support future high-rise towers. The tunnel will link previously completed tunnel sections under Hudson Yards to future tunnels under the Hudson River. The design aims to minimize constraints on future overbuild and future tunnels, while maximizing constructability within a small worksite. The tunnel will pass under the High Line elevated walkway, next to an active rail yard, and close to a subway tunnel. The design was developed by a tri-venture of WSP, STV and AECOM. WSP led the design of major underground works; STV designed utility relocations and the underpinning concept for the High Line; and AECOM designed temporary in-tunnel systems. Construction is expected to start in 2023.

Jun 13, 2023

By David Beck

In Australia, Safe Work legislation requires mines to have a documented ‘Safety Case’ explaining how a mine will safely manage all major hazards. A similar requirement is legislated or inferred by regulation in all jurisdictions. For small scale, instabilities leading to day-to-day seismic hazards, a ‘Stability Safety Case’ built around observational methods and measurement triggered responses can be effective because adverse situations are easily identified and the costs of lower control measures are not onerous. Also, if the influence of a volume of yield on the mine load system is small, the response of the system will be more predictable. However, for episodes of large scale mine instability, the hazard derives from the widespread, multi component influence of the event on the mine load system. As the system response depends on interactions between many parts, the resolution of predictions will be lower and situations can arise without local precedent. Further, as episodes of large scale instability change the stiffness and nature of the connectedness between parts of the mine load system, the behavior of the system before the event will be a poor empirical basis for forecasts of event related hazards. Most importantly, Triggered Action Response Plans (TARPs) and ‘traffic light’ warning systems cannot make design choices or identify new hazard phenomena. They are ‘lower’ control measures targeting explicit human-made instability hypotheses. As such, the Safety Cases related to management of hazard from potential large scale seismic events and mine instability cannot rely solely on TARPs. Mines that successfully manage meaningful dynamic instability always acknowledge the ultimate reliance on expert human intuition, knowledge and imagination to appreciate the range of possible hazard scenarios, to make stability hypotheses and propose solutions. Complex analysis, TARPs and measurements are critical steps in the human decision cycle, but only support the making and testing of ‘Stability Hypotheses’ made by expert engineers. Relying on expert skill and judgement as essential components of a Safety Case, however essential, introduces human vulnerabilities. Another challenge is that the expert decision making process is hard to document. Beck et al 2019 first described an organizational and procedural framework for maintenance of an ongoing large-scale ‘Stability Safety Case' where a degree of expert judgement and imagination is needed to manage a seismically active mine. The structured data appreciation process outlined sufficient measurements, analysis and appreciation to confirm the stability state of the mine and was applicable to all underground mines. After several years of implementation in various forms in stoping, caving and room and pillar mines, this update addresses lessons learned and describes some considerations for numerical forecasting to establish a base case, and some challenges for empirical hazard identification.

Apr 26, 2022

By Michael L. Maniocha

Most magnesia (MgO), whether of natural or synthetic origin, is used in the dead-burned or periclase form as refractory linings for the production of steel. Continued research in refractory science, combined with good refractory maintenance and improvements in steel-making processes, have resulted in decreased use of magnesia. To make up for this loss of business, producers of synthetic magnesia have started to manufacture a variety of magnesium-based chemicals that are used in many industries. There are three primary methods of producing MgO. The first involves the calcination of naturally occurring minerals species. Most of the magnesia produced by this method uses the rhombohedra1 carbonate mineral magnesite, MgCO,. To a lesser extent, the mineral brucite, Mg(OH), is calcined to magnesia. Magnesia produced by the calcination of minerals is called natural magnesia. The second production method uses magnesium-rich brines, or sea water reacting with lime or calcined dolomite to produce magnesium hydroxide. The magnesium hydroxide is subsequently calcined to magnesia. Material produced in this way is called synthetic magnesia. The third major method of production uses saline lake brines to produce magnesium chloride. Magnesium chloride brine is sprayed into a reactor where it thermally decomposes into MgO and HCl. The magnesia is purified by slaking to magnesium hydroxide followed by calcination. Magnesia produced in this manner is also know as synthetic magnesia (Duncan and McKracken, 1994). The degree to which the magnesium minerals or the synthetically prepared magnesium hydroxide is calcined governs the physical properties of the resulting MgO. It is the physical properties that dictate the end use for the product. The terms used to describe magnesia vary along with the degree of calcination. Table 1 summarizes the terminology used when discussing the various forms of magnesium oxide.

Jan 1, 1997

By G. Wayne Clough

During shallow tunneling in an urban environment, deposits or pockets of saturated soil or fractured, weathered rock are often encountered. Under such conditions, special problems with tunnel support, underpinning of structures adjacent to the tunneling, and/or flow of groundwater into the tunnel occur. If the ground conditions are appropriate, i.e., the soil is sandy, silty or fissured, or the rock is weathered or fractured, the solution to these tunneling problems may be chemical stabilization of the ground. Injection stabilization as an aid to tunneling is practiced extensively in Europe and its use is increasing in the U.S. The advantages of this technique over conventional solutions can be substantial in terms of cost and time, especially in mechanized tunnel boring where even a small zone of soft ground can bring the tunneling to a complete halt. In this paper European practice in using chemical ground stabilization for urban tunneling will be reviewed. In contrast to previous papers which have dealt with specific applications (1,5,8,9) this paper will broadly cover the subject, addressing itself to grouting techniques, costs, the reasons for grouting, philosophy of the users towards grouting, design of grouting solutions (or lack thereof) and methods of quality control. Differences with U.S. grouting practice are also noted. The information presented is derived from several visits to Europe, discussions with European and U.S. grouting personnel, and the available literature (2). The author's most recent European trip was made under the auspices of the U.S. Department of Transportation in conjunction with a research study being performed at Stanford University; a detailed report of this visit is available in reference (6).

Jan 1, 1976

By Rafael Moure

On April 21, 1980 the Oil, Chemical and Atomic Workers Union (OCAW) submitted a petition urging the revision of the Mine Safety and Health Administration (MSHA) permissible exposure limit to radon daughters in underground mines. This petition asks for: 1. Annual worker exposure to be lowered from the current 4 WLM/year to 0.7 WLM/year; 2. Full economic protection for workers whose exposure exceeds the proposed 0.7 WLM/ year; and 3. The primary means of lowering workers' radiation exposures shall be environmental controls. I will present the scientific rationale for the lower standard requested in our petition to the Department of Labor. [1. Radiation Exposures to Uranium Miners] Two types of radiation exposures are present in the environment of uranium mines: A. [External Exposure] to gamma sources which until 1978 was considered as negligible compared with internal alpha radiation. R. E. Utting (1), in an investigation of three Canadian uranium mines, found levels of exposures adding to an annual dose equivalent of 3 rems (30 mSv)/year. He concluded that gamma dosages may be a major fraction of the maximum permissible dose for many individual miners. The U.S. experience has shown that there is significant gamma exposure in U.S. uranium mines and, therefore, it could contribute to the total radiation exposure to the lungs in combination with internal alpha radiation. Before ventilation improvements in uranium mines, the contribution of external radiation to total lung dosage was relatively small. After improvements in ventilation, the reduction in internal radiation exposure appears to be in 1980 as low as 1/10 of the 1950 dosages. However, ventilation improvements do not affect external gamma radiation. Gamma radiation remains at the same 1950's level, and it represents today a higher proportion of the total radiation burden to the miner's lungs. MSHA regulations (57.5-47) state that if gamma exposure is below 2.0 milliroentgens per hour, then workers are not required to wear gamma dosimeters and cummulative gamma radiation records need not be kept. Assuming an exposure of 1.9 milliroentgens per hour per 173 hours/month for 12 months,a miner would accumulate a dose from external radiation of 3.9 rems/ year. This dosage would, of course, go unrecorded. MSHA, therefore, should consider a downward revision of the external radiation permissible exposure limit of 2.0 milliroentgens/hour. MSHA should make clear that this exposure level, when added to the internal exposure, does not make for sound health physics -even though the measured current levels do not approach 2.0 milliroentgens/hour. B. [Internal Exposure] to alpha radiation is still the larger contributor to lung irradiation in uranium miners. The target organ is still the lung. The parameters to be considered in determining the biological radiation load appear in Table I for radon daughters present in the upper respiratory tract (URT). TABLE I RADIATION DOSE PARAMETERS IN THE URT OF URANIUM MINERS Parameter Uranium Underground Mining [1. Quantity of the Absorbed Radon daughters (Po-218, Nuclide Pb-214, Bi-214) deposit in bronchial and lung tissue. (Measured by air concentration, Working Levels) 2. Type of Radiation Emitted Alpha Particles 3. Energy of Radiation High-Linear Energy Transfer 4. Half-life of the Nuclide Ra 222, 3.8 days in the Organ Po-218 (RaA), T1/2 = 3.1 minutes Pb-214 (RaB), T1/2 = 26.8 minutes Bi-264 (RaC), Vi = 19.7 minutes 5. Selection Factor of the Direct inhalation with mine Organ dust to be deposited in the tipper Respiratory Tract 6. Mass and Form of the Organ Especially cancer sensitive, tracheobronchial region and bronchi* 7. Distribution of the Activity Dependent on deposited dust in the Organ distribution in the Upper Respiratory Tract 8. Chemical Nature of All compounds (RaA, RaB, RaC) Incorporated Substance biologically insoluble. (Only localized, irradiation) *See Reference (2)] The parameters of Table I depend, in turn, on the demography of the exposed population, especially: 1. Age 2. Sex 3. Health Status 4. Genetic Constitution 5. Lifestyle (Smoking, Diet) Some of these demographic characteristics of uran-

Jan 1, 1981

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By Victor Despointes, Stephane Polycarpe, Kathryn Kelly, Chris Feeney, Brian Hann, Vojtech Ernst Gall

The Pawtucket Tunnel is a 2.2-mi, 30.2-ft diameter CSO storage tunnel in Rhode Island. The primary tunnel is built using a dual-mode open-EPB TBM capable of sealing the face within 120 seconds to manage poor ground and water ingress which is launched from within a SEM starter tunnel. The main tunnel connects to four adits along its alignment, three of which are SEM tunnels and one being a MTBM tunnel. This contribution describes the selection process, potential risks, and requirements for the TBM, as well as the design of the main tunnel, the adits, and the adit-bored tunnel connections.

Jun 13, 2023

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

By Jin Zhao, Weijie Wei, Jinwang Zhang, Xiaohang Wan, Shengli Yang

Reasonable mining-retention ratio (ratio of room width to pillar width) is vital to recovery rate and stope stability in underground mining of solid potassium salt deposits. Based on the engineering background of a solid underground potassium salt mine in Khammouan Province, characteristics of the plastic zone of the pillar, and the variation of recovery rate and stope stability under different mining-retention ratio conditions are discussed. The results show that compared with current room width (8 m) and pillar width (10 m), the optimization method of improvement of stope stability. The research results are helpful to recover as much solid potash resources as possible under the premise of ensuring the stability of stope.

Jun 25, 2024

By R. Y. Wan

Newmont Gold Company has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for pretreatment of low grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the "preg-robbing" characteristics of the carbonaceous matters in the ores. An alternative heap leach process using ammonium thiosulfate was developed to extract gold from the "preg-robbing" biooxidized ores. The ammonium thiosulfate leach process has been successfully practiced both in laboratory and pilot plant testing. Satisfactory test results encourage the continuation of process development.

Jan 1, 1996

By Anthony W. Garson

Good morning, ladies and gentlemen: It is a pleasure to be here this morning as a representative of Dean Witter Reynolds; one of the foremost international investment firms in North America. My colleague, Hugh Wilmer (who will be speaking to you a little later), and I are involved as research analysts in the research and writing of published reports containing recommendations on the buying or selling of North American and South African gold and silver mining shares. Our talk this morning will focus on the gold mining operating costs of North American and South African gold producers. However, I am not going to bore you with reams of statistics on the operating costs of large numbers of gold mining operations; how meaningful would this data be to you? Instead, I will discuss what the investor should look for, and how he should use this knowledge in making his investment decision.

Jan 1, 1984

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, MSHA began requiring the use of continuous personal dust monitors (cPDMs) to monitor and measure respirable mine dust exposures to underground coal miners. After the cPDM’s implementation, mine operators discovered that it interfered with proximity detection systems (PDSs), thus exposing miners to potential striking and pinning hazards from continuous mining machines. NIOSH was sought out by MSHA and mining industry stakeholders to determine how the cPDM and PDS interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments, and conducted lab evaluations. Some interferences were observed to be caused by electromagnetic interference (EMI) from the cPDM. Results showed that there was no significant interference when the cPDM and the miner-wearable component of the PDS were separated by distances of 6 inches or greater. In this study, the cPDM and PAD needed to be at least 6 inches apart in order for them to be used simultaneously and reduce interference potential. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis such as coal dust exposure, high noise levels, roof and rib falls, the potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 40 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (1,2). Proximity detection systems (PDSs) are designed to alarm miners and stop machine motion in order to protect miners from being struck, pinned or crushed by CMMs(3). Currently, MSHA-approved PDSs, installed on CMMs, are based on the principle of magnetic flux density (B-field) (4,5). The system generates a magnetic field around a CMM and determines the relative distance a miner is from the CMM based on a detected magnetic flux density. A PDS typically consists of multiple magnetic field generators mounted at different places around the CMM, and personal alarm devices (PADs), which are worn by the miners to detect the magnetic flux density. When a miner, wearing a PAD, gets closer to the machine, the PAD detects a stronger magnetic field from the generators and detects a weaker magnetic field when a miner moves away from the machine. The magnetic field generators installed on CMMs typically produce modulated magnetic wave signals at frequencies between 10 kHz and 120 kHz. The magnetic fields are measured by three small magnetic coil antennas mounted on orthogonal axes inside of the PAD worn by the miner. According to Faraday’s Law, the changing magnetic field induces a voltage in each coil antenna, and the voltage values are transmitted from the PAD back to a controller on the CMM wirelessly, typically at a frequency between 400 MHz and 2.5 GHz. These values are then used to determine the distance between the miner and the generators of the machine. Typically this information is used to determine when a miner wearing a PAD is in a warning zone or stop zone which would trigger different alarms and actions such as slowing the machine down or stopping it."

Jan 1, 2017

By W. Clark Ashby

Productivity is a fascinating concept. Like motherhood or apple pie, we know it as a good thing. Just what it means is not so clear. To a coal miner we assume it means tons of coal hauled from the mine. To the company president it means profit after capital, labor, and other costs have also been reckoned. To the government economist it means output in a balance of payments. What does it mean to the biologist, and can reclamation really be productive? In this paper we discuss productivity from a biological viewpoint, give some yield data for various types of reclamation plantings, and discuss how our demand for or acceptance of differing kinds of productivity is tied up in bigger questions of land use, environmental stability, and resource allocation.

Jan 1, 1981

By K. W. Lentz

The Maybell Mill of, Trace Elements Corporation, Unit of Union Carbide Corporation is located approximately five miles northeast of Maybell, Colorado, and twenty-five miles northwest of Craig. It is located in the midst of the uranium ore deposits whose presence, made it possible. In November 1953 Russel Cutter, Chief Geologist for the original Trace Elements Corporation, picked up high readings on a scintillometer while flying over this area. Later, with George Morehouse, Chief Engineer for the original. Trace Elements Corporation, he started a search for surface indications. In this search, they found an out crop which can be regarded as the discovery lode on this property. The actual locating of claims and acquiring free lands and state lands was begun in March 1954. During 1955 enough drilling was done to indicate that a sufficient tonnage of ore existed to make possible a mill. These ore deposits are located in the Browns Park formation which is an unconsolidated sandstone with a few hard lime ribs running through it. The geologists tell us that this region was once a vast basin which became filled with wind blown sand and volcanic tuff, Later on, ground waters brought uranium into the basin which precipitated out in the sand. During the late summer and fall of 1955, a small pilot plant was operated under the supervision of John L. Chapman testing these Browns Park ores. During the operation of the pilot plant, three small open pits were developed and the ore from these pits shipped to Union Carbide Nuclear Company, Division of Union Carbide Corporation, at Rifle. To date all ore is being mined from open ptis. In the fall of 1956 the original Trace Elements group signed a contract with: the AEC for a mill at Maybell and on November 5, 1956, Union Carbide acquired the Trace Elements Corporation properties and contract. During the next two months, intensive research was carried out on the Browns Park ores by our research lab at Rifle. They also checked some of the metallurgical results which had been obtained through the operation of the pilot plant by the original Trace Elements group. During this period, a report on Trace Elements Corporation ores was also prepared by the Colorado School of Mines Research Foundation. This report contained data on representative samples of the ore tested for the original Trace Elements group. From this research and study a flow sheet was decided upon.

Jan 1, 1959

By William F. Lawrence

Research performed by the West Virginia University Coal Research Bureau under the sponsorship of the U. S. Bureau of Mines has demonstrated that coal-ash can be converted into mineral wool insulation of a quality equal to commercial grade mineral wool. An unexpected benefit has been gained due to the discovery that the usual and costly fluxing agents employed when using conventional raw materials are not required when producing mineral wool from coal-ash. Because coal-ash sources are commonly located close to mineral wool marketing areas and because mineral wool is seldom shipped far as a result of its low weight and high volume, the use of coal-ash may offer the mineral wool producing industry profitable opportunities. Moreover, coal-ash produced from experimental limestone based air pollution control processes also yields high quality mineral wool which may aid in retarding corrosion of metals contacted by the wool. In addition, internal fluxing effects and possible sulfur oxide utilization could provide economic advantages to the use of these "modified" ashes.

Jan 1, 1969

By F. Ikumapayi

In order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the influence of major species, calcium and sulfate in process water on sphalerite flotation was investigated through Hallimond tube flotation, zeta potential, diffuse reflectance Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements using sphalerite mineral sample. Assessment of process water species in flotation was done using deionized water, process water and simulated water containing calcium and sulfate ions in experiments. Hallimond flotation shows increased sphalerite float-ability in process water compared to deionized water, but no significant effect on the presence of calcium and sulfate ions in deionized water using isobutyl xanthate as a collector. The presence of calcium ions reduced the sphalerite?s negative zeta potential, while at higher concentrations, a charge reversal occurred, at about pH 11. FTIR and XPS studies revealed the presence of surface-oxidized sulfoxy and carbonate species on sphalerite at pH 11.5 in deionized water, process water and water containing calcium and sulfate ions. These surface species do not influence xanthate adsorption.

By M. Springett

Organization of teams for rapid and effective evaluation of international mining properties requires special considerations beyond those needed for domestic activities. Experience, technical ability, a sense of perspective, humor and self-discipline are vital characteristics to look for in the selection of individuals for forming an efficient and productive team.

Jan 1, 1994