Search Documents

By Muhammad I. Kabir

The streamline method of recovery prediction reduces a two-dimensional problem to a bundle of one-dimensional ones. This paper presents the development and application of a novel scaling technique which, when used with a streamline model, causes s bundle of one-dimensional problems to further reduce to a single one-dimensional calculation. The one-dimensional calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desk-top calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the Interior Department's Bureau of Mines.

Jan 1, 1984

By Weibai Hu

Four methods to assess the relative flotability of fine coal have been tested: flotation with frother only, flotation with frother and collector, salt flotation, and timed-release analysis. A practical and simple criterion which combines the separation efficiency (capacity factor and kinetic rate constant (intensity factor) has been suggested. Five coal samples are chosen and tested. Based on test results, it is concluded that the flotability test with collector and frother is closer to practice, and, according to the suggested flotability criterion, coal fines can be classified into four categories of relative flotability: very easy, easy, moderate, and difficult.

Jan 1, 1987

By J. C. Motz

With ore grades continually decreasing and finer mill feed requirements, it becomes increasingly important to have the capability to handle the larger tonnages economically. With the 10 ft. Standard capable of reducing 1,633 metric tons per hour (1,800 short tons per hour) to 80 percent passing 50 MM (2 inches) and the 10 ft. Short Head following to produce a mill feed of all minus 12 MM (1/2 inch) at a rate of 608 metric tons per hour (670 short tons per hour), we feel significant savings will be realized in installation and operating costs. The largest concentration of cost in the secondary and tertiary crushing stations is the building itself that houses the process equipment. An example of the savings to be attained can be seen from an examination of a 40,820 metric ton (45,000 short ton) per day crushing plant. A total of nine 7 ft. Symons Cone crushers is used to generate 12 MM (1/2 inch) ball mill feed. The average center distance between units is 6.1 M (20 feet) and allowing a 6.1 M (20 feet) nominal distance from the centerline to the wails, the building becomes 61 M (200 feet) long. For this production rate, four 10 ft. Symons Cone crushers would be required. With the 10 ft. crushing plant requiring a center distance spacing of 7.6 M (25 feet), the building length totals approximately 38 M (125 feet). Construction costs vary depending on location, but a reduction in building length from 61 M (200 feet) to 38 M (125 feet) will result in estimated savings of between $2,500,000 and S4,000,000. While the 10 ft. Symons Cone has been involved in a number of feasibility studies for some time, the Process Machinery Division of Rexnord commenced detail design work on the 10 ft. Cone crusher in 1972. For comparison purposes, the 10 ft. and 7 ft. capacities are given in Table 1.

Jan 1, 1978

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment such as haul trucks often account for the greatest number of fatalities in the mining industry each year. Despite previous analyses that have identified root causes and other contributing factors, there is still a need to better understand the events leading up to these types of accidents, what lessons may be learned, and what strategies can be employed to prevent fatal accidents from occurring. This study examines Naturalistic Decision Making (NDM) using the critical decision method (CDM). The CDM is a retrospective interview approach used to explore timelimited, high-stakes, decision-making. In this study the CDM is used to obtain more information about what happens prior to, during, and after a potentially fatal situation such as a near-miss event, loss of control, or minor accident involving equipment damage. Researchers captured firsthand accounts from 21 haul truck operators involved in near-miss events from mine sites of various sizes and commodities throughout the United States. These accounts provide rich and detailed narratives from the perspective of haul truck operators themselves and reveal insights into what decisions haul truck operators make, what sensory cues they perceive, and what strategies they employ during challenging and non-routine situations. Decision-related themes that emerged from the data are presented and discussed. These results, along with potential solutions offered by study participants, can help to inform future research, raise awareness about hidden hazards, and build more creative interventions and realistic training scenarios for use by the industry to address haul truck safety issues.

Feb 1, 2024

By H. Kinilakodi, R. L. Grayson

In 2010, the U.S. Mine Safety and Health Administration (MSHA) began holding hearings on a new coal mine respirable dust rule, which proposed a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the “hot spots” where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines’ compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, average mining height and selected “hot spot” counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications for the need for better dust control methods.

Jan 1, 2012

By H. A. Kortmann

For the commercial production of iron ore pellets from hematite ores, as it is practiced in various pellet plants, the addition of lime has shown to be an efficient means with a view to improving cold compression and abrasive strength of the indurated pellets considerably. Unfortunately, it has also been shown at the same time, that the metallurgical properties as, for instance, swelling behavior, softening during reduction under load and disintegration of the grain, can be adversely affected to a high degree. In the course of smelting tests carried out by renowned steelworks, blast furnace operation was heavily disturbed by the swelling and early softening of the pellets, also by their disintegration in the low-temperature range, which altogether led to a considerable lowering of the smelting rate (1, 2, 3).

Jan 1, 1972

By Hossein Ghaedi, Hadi Fattahi

Despite the significant role of coal in the economic progress of nations, the occupational and health risks associated with its mining pose a major concern for industry stakeholders. The occurrence of roof collapses in coal mines remains a critical factor leading to substantial loss of life and financial damages for miners. Therefore, accurately predicting the roof fall rate (RFR) holds paramount importance. However, the uncertainty surrounding rock parameters in mines hinders the application of conventional methods to assess roof collapse rates in coal mines. To tackle the challenges associated with predicting roof fall rates in underground coal mines, this study proposes a novel solution by leveraging the Rock Engineering System (RES) method. The investigation is grounded in a dataset comprising 109 data points, encompassing crucial input parameters like depth of cover (DOF), primary roof support (PRSUP), intersection diagonal span (IS), mining height (MH), and coal mine roof rating (CMRR). In the model construction phase, 80% of the data (87 points) were utilized to build the RES model. A critical aspect of this study involves the evaluation of the RES model’s performance against alternative regression techniques, namely linear, power, exponential, polynomial, and logarithmic regression. This comparison was executed using the remaining 24 data points (20% of the dataset) for rigorous evaluation. Employing key statistical metrics such as mean square error (MSE), root mean square error (RMSE), and squared correlation coefficient (R2), the study systematically demonstrated the superior accuracy of the RES-based method compared to other approaches. In conclusion, the outcomes strongly support the efficacy of the RES method in predicting roof fall rates, not only in the specific case studied but also indicating promise for its application in other underground coal projects. This underscores the potential of the RES method as a reliable and versatile tool for forecasting roof fall rates in the complex and critical context of underground coal mining.

Mar 19, 2024

By M. Rieber

The potential for the wide-spread commercialization of superconductivity, the disappearance of all resistance to a direct current (D.C.) electric flow, began in 1986-87 with the development by Bednorz and Muller at IBM's Zurich Laboratory of an yttrium -barium -copper oxide conductor which attained zero resistance at 90t:. Although the status of superconductivity is still pre-bench scale, it is useful to forecast its probable effects on the copper industry. I t should not be forgotten that at their inception, the impacts of transistors, semi-conductors, thin films and fiber optics on the electric/electronics sector of this industry, were largely underestimated. Superconductors are not metals, but a class of ceramics. They represent an efficiency increase of one or more orders of magnitude. If their development is to be a boon to the copper industry, rather than a reduction of metal demand through miniaturization or material substitution, vastly expanded copper containing electrical uses must be in prospect. In this paper the projected uses of high temperature superconductivity are examined, followed by the remaining problems to be overcome. Assuming success, a time horizon for maturation is estimated. The penalties for the non-recognition of new markets and material substitution are shown on the basis of past forecasts. Finally, the application of successful superconductivity to the copper industry over the forecast period is estimated.

Jan 1, 1990

By D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, increasingly are becoming important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance techniques and correlated to flotation response. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for 1?) d at 65? C inhibited flotation of chalcocite, and chalcopyrite even after the addition of a large amount (1 x 10') M) of collector. Heavily oxidized (27 d) chalcocite remained unfloatable. However, longer oxidation of pyrite and chalcopyrite restored the floatability. Oxidation resulted in an electrically resistive, nonporous surface layer.

Jan 1, 1993

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By Earle Faig

Earle Faig Along with other transportation modes, the barge industry will be greatly affected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events has caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of its long experience in moving large quantities of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to that industry. Barge companies operate on a river system that is over 40 Mm (25,000 miles) long. It includes the East and West Coasts and the Mississippi River System comprised by the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior-Tombigbee, and Mobile Rivers, and some smaller tributaries. The Gulf Intracoastal Waterway stretching along the Gulf Coast from Brownsville, TX, to Apalachicola, FL, also is considered part of the inland waterway system. Approximately 1,800 companies operate on the inland river system and have a combined fleet of about 4,400 towboats and 28,000 barges. The fleet of towboats represents 4.8 GW (6.4 million hp) of power. The towboats comprising this fleet vary in size from a small harbor boat to a large line haul boat with 7.5 MW (10,000 hp) of power. The choice of size and power of the boat depends on a number of factors, including the size of the river and operational constraints, such as lock size, river-current rate, and water level. The choice also depends on the tow size. A single tow on a river capable of locking through 15 barges at a time handles up to almost 20 kt (22,000 st), whereas a tow on the lower Mississippi, which has no locks, can accommodate up to 41 kt (45,000 st) of cargo. Because the quality of coal is not typically damaged by exposure to the elements, it is usually moved in open hopper barges, although covered barges are used occasionally. The most frequently used size is the jumbo barge that measures 59 m (195 ft) long by 11 m (35 ft) wide by 4 m (12 ft) deep and can handle up to 1.4 kt (1,500 st) of coal. Advantages of Barge Transportation Barging offers several inherent advantages in transportation of bulk commodities like coal. First, barges can carry large quantities of product. A single jumbo hopper barge can handle 1.4 kt (1,500 st) of cargo while it takes 15 91-t (100-st) capacity rail cars or 57 trucks hauling 24 t (26 st) each to move an equivalent amount of cargo. Thus, barges can move more tonnage with less equipment than competing forms of transportation. Second, barging offers the most fuel efficient means of transportation. Less energy is required to push a load over water than to pull a similar load over land. The amount of pollution attributable to barge traffic is minimal because barges consume less fuel. Third, barging is an inexpensive form of transportation. The inland waterway industry transports about 12% of the nation's freight for about 2% of the total freight bill. This can be attributed to competition between the large number of companies on the river system and competition with other transportation modes. Fourth, barging is an environmentally safe method of transportation. Inland river routes expose fewer urban areas to hazardous substances than rail or truck. And barge spills occur less frequently than rail or truck spills. The industry does pose some disadvantages. The waterway system is constrained by the natural river network, so barges cannot travel on the most direct straight-line route. This means that barging is usually an incomplete form of transportation requiring interface with truck or rail. The industry's market is limited to those geographical areas that are located on or near the rivers. In addition, it is a time-consuming transportation mode, making it impractical for many types of commodities.

Jan 10, 1982

By G. T. Daware, M. J. Chaddha, S. P. Masurkar, P. G. Bhukte, A. Agnihotri

JNARDDC has evaluated bauxite deposits of India from the geo-technological point of view. During the evaluation studies, it was observed that bauxite deposits are associated with saprolite resources. During bauxite mining, various low-grade materials such as saprolite, laterite and low-grade bauxite are generated. These materials typically have low-alumina, high-iron oxide and high-silica content. Owing to their inferior quality, these materials cannot be used for alumina production and hence remain unutilized at the mine site. For the present study, the saprolite samples were collected from the Western Ghats bauxite deposits in India. The sintering studies were conducted on saprolite granules using a variety of parameters. The sintered granules were characterized, and their properties determined. The test results showed that bulk density, apparent density, porosity and refractoriness (PCE 1645–1659 °C) of the aggregates were within the range of refractory specifications. The feasibility tests carried out at the refractory industry indicated that the developed aggregates are suitable as refractory material and can substitute for calcined clay. Currently, high-purity clay resources used in the refractory industry are limited and fast exhausting; therefore, the industry is likely to face an acute shortage of raw materials, which will become more critical in the future. Therefore the sintered granules (aggregates) developed from saprolite, which is a mining waste, provide a low-cost, eco-friendly solution for the fast-exhausting resources of the high-purity clays. The developed process may change the Indian bauxite mining scenario because saprolite may substitute as a potential raw material for the refractory industry.

Apr 12, 2021

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By B. G. Hicks

The Manapouri Power Project is located in New Zealand's South Island Fiordland. The project is being constructed for the New Zealand Ministry of Works. Construction began in 1963 and is scheduled' for completion in 1969. The project will divert water from the natural, glacially carved Lake Manapouri, at Elevation 580, through vertical- penstocks into an underground powerhouse 364 feet long, 127 feet high, and 59 feet wide excavated about 700 feet below ground surface and about 560 feet below the present lake level. The possible ultimate power installation will produce 700 megawatts from turbines located in the underground machine hall. The turbine flow will discharge through the 6-mile, 30-foot diameter tailrace tunnel into a fiord arm of the Tasman Sea. The rocks in the project area are primarily Paleozoic Fiordland Complex gneiss, schist, amphibolite, and marble intruded by granitic rocks and pegmatite. Shear zones have been encountered in the tunnels and machine hall. These produce water and occasionally require steel support. The machine hall arch was stabilized entirely by rock bolt reinforcement. Rock mechanics instrumentation has been used throughout the project both for pre-construction design calculations and to monitor tunnel rock loads and movements of the machine hall roof and walls. About 28 miles of the 100-mile transmission line will be constructed across glacially oversteepened slopes and debris or swamp filled valleys between the power plant and the eastern edge of the mountainous area. Steep glacially carved rock slopes and locally unstable glacial till complicated construction of the transmission line access roads.

Jan 1, 1968

By Aimee A. Woolsey

Enterprise Unmanned Traffic Management is a holistic system concept evolving from technological developments in radio frequency where dynamic tracking can be added into current and emerging platforms. This is done through inexpensive RF sensors capable of real-time and cooperative, non-GPS tracking enabling digital visualization of assets, including unmanned aerial systems (UAS). The RF sensors are low size, weight, and power (SWaP), creating efficiencies in energy and material consumption while transmitting positions in real-time and at long ranges. Multiple UAS and other unmanned vehicles can be visualized for risk mitigation in operations,

Oct 17, 2022

By Lee W. Saperstein

In surface mining for coal, common practice for the disposal of preparation plant refuse is to bury it. As with surface refuse piles, these buried wastes can ignite and can also lead to ground and surface water pollution. Steps to ameliorate these problems have been devised over the years. C and K Coal Company, of Clarion, Pa., the largest Pennsylvania surface mining company, has incorporated all of these steps and added of few, of their own in their latest disposal practice. In addition to layering and compacting, C and K practices selective placement and dilution to minimize longterm problems.

Jan 1, 1977

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021

By A. D. MacPhail

The Highland Valley Copper partnership was formed in July 1986 and was the logical result of a mine with a large ore reserve but no adequate mill, and a mine with a large, modem mill but dwindling ore reserves. The original partners -Cominco and Lornex -were joined in January 1988 by Highmont Mining Co. which contributed a two-line concentrator. During 1988/1989, the Highmont mill was moved 7.5 km to adjoin the Lornex mill, forming what is now called the Highland mill, with a current nominal capacity of 130 000 tonnes per day. The mine is located 220 km northeast of Vancouver, British Columbia and is close to four communities in which personnel make their home: Logan Lake, Merritt, Ashcroft, and Kamloops. The map in Figure 1 2.2 shows the general area. Kamloops is a major service centre and is serviced by two railways, two major roads and a regional airport.

Jan 1, 1993

Iran possesses very large copper resources, estimated to contain around 4-5% of the world's known copper inventory. There are several small private sector copper mining operating in the country, but Iran's copper industry is dominated by the state-owned National Iranian Copper Industries Company, which operates the world-class Sar-Cheshmeh open-pit Mine. This mine was developed in 1970s before the 1979 Islamic Revelation by the Atlantic Richfield Company (ARCO), the former Anaconda Copper Mining Company. Current Iran?s copper cathode production is about 250,000 mtpa and recently it is targeted to reach to 700.000 t by 2014. The required finance for this target is estimated US $2.25 -b, i.e. US $5000 for each tonne capacity. The copper content of the mineable reserves of the country is estimated about 19 Mt. It is not unlikely this amount increases in close future. Currently, almost 30 projects consist of mine, concentrator, smelter, refinery, acid plant, leaching, bio-leaching are underway. These projects are a golden opportunity for the local and foreign companies, but the recent sanctions are very challenging that all studied in this paper.

Jan 1, 2012

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980