Search Documents

By R. O. Ifill

Alternating current electrocoagulation (AC/EC) may be an alternative to chemical coagulation in the thickening of tailings in the mineral, coal and petroleum industries. In the current study, ground silica (d50 as received, 20 µm) served as the model tailings solid with characteristically poor settling behavior. Its natural initial settling rate was 1.6 x 10-3 cm/min. This paper discusses the indirect application of AC/EC via aluminum electrodes to the enhancement of the settling behavior of the silica. ?Indirect AC/EC? means that the silica was coagulated upon dispersion in water that had been treated by AC/EC. The effect of AC/EC retention time on settling behavior is examined and the water chemistry is analyzed. Test results show that the initial settling rate of silica was enhanced by a factor of 4,000 at its maximum of 6.4 cm/min, under the conditions employed. Settling enhancement was achieved upon contact between the AC/EC-treated water and the silica, and the enhanced initial settling rate was dictated by the floc size. The aluminum dosage increased with AC/EC retention time, reaching a maximum concentration that was equivalent to 13.1% of that predicted by Faraday?s law. Complex aluminum ions are considered to have adsorbed onto the silica surface and an adsorption mass ratio of 0.3 mg Al/g silica was the most effective in enhancing settling behavior. Owing to pH change or slow kinetics, aluminum hydroxide precipitation did not lower the ion product ([Al3+][OH-]3) below the KSP of 6.3 x 10-32.

Jan 1, 2011

By Abdelaziz Baçaoui, Imane Aarab, Mohammed Derqaoui, Abdelrani Yaacoubi, Khalid El Amari, Abdelmoughit Abidi, Abderahman Etahiri

Numerous researchers have addressed the complexity of the direct flotation separation of apatite from low-grade phosphate ore. The majority of these studies were limited to the micro-flotation scale. In fact, there is no warranty that a reagent scheme that showed a direct flotation of apatite at a micro-flotation scale on pure minerals would automatically replicate the same expected results on the natural ore in the mechanical flotation cell and so was the case for the phosphate ore studied. The overall trend was concentrating apatite in the non-float product. This study aspired to thoroughly assess the flotation performance of this never-exploited low-grade sedimentary phosphate using design of experiments (DOE). Unveiling new insights on such a strategy twist, various parameters and operating conditions, namely, desliming, type of collector and depressant, reagents dosages, conditioning times, flotation time, and pH, were addressed by multiple-factor screening using asymmetrical fractional factorial design followed by statistical interpretations. The collectors tested were the sodium oleate and a fatty acid mixture (FAM). The depressants tested were sodium alginate (NaAL), corn starch, carboxymethylcellulose (CMC), and sodium silicate. The results of the multivariable analysis revealed that desliming, pH, collector dosage, and flotation time significantly influenced the flotation process. Desliming was beneficial for the yield, P2O5 recovery, and SiO2 removal; however, there was still a compromise between grade and recovery. A strongly alkaline pH value of 12 stood out from the whole range. P2O5, CO2, and SiO2 grades of the products and flotation recoveries were improved, except for P2O5 recovery, which was negatively affected. A collector dosage between 2000 and 3000 g/t increased the P2O5 grade and reduced CO2 grade and recovery, enhancing the apatite/carbonates separation. A flotation time of 15 min was significant for P2O5 grade and CO2 recovery, nevertheless, at the expense of yield and P2O5 recovery. The products having initial concentrates of 28.08% P2O5 with a recovery of 88.96% and 29.41% P2O5 with a recovery of 62.71% were obtained using 25 g/t of NaAL and 2000 g/t of the collector FAM and sodium oleate, respectively, at pH 12.

Jun 5, 2022

By C. G. Anderson

Extraction of valuable resources from complex orebodies will become more common. This is obvious for two reasons. First, the cleaner and more readily processed ores have continually been depleted through centuries of mining. Second, new technologies have evolved for effectively handling complex ores. One of these new processes has been in place at Sunshine since 1984. Based on sulfuric acid oxygen pressure leaching with nitric acid as an oxidizer, this patented technology allows silver and copper to be efficiently recovered from a complex sulfide concentrate. As efficient as it is, this process represents novel technology found nowhere else on an industrial scale. As such, a research program was undertaken in 1989 to optimize this leach process and to better understand it. From this study, several potential plant improvements were found and recommended. As a result, two of these options, nitric acid replacement by sodium nitrite and concentrate regrind are now used in day to day operation at Sunshine. Patenting of these changes was recently accomplished (1). Thus, the development, perceived mechanisms, plant integration and potential applicability of this technology will be covered in this paper.

Jan 1, 1994

By W. C. Hirt

Deposits of ferromanganese crust containing cobalt and nickel occur on the seafloor in the Pacific Ocean near the Hawaiian Islands and Johnston Atoll. This paper describes developmental flotation metallurgy to separate crust from its associated substrate gangue. Important variables in ferromanganese crust flotation include reagent type, aeration rate, conditioning time and agitation intensity, pH, temperature, water type, and feed size distribution. Flotation in seawater of minus 600 ~m (-28 mesh) material assaying 6.2% Mn, 0.2% Co, and 0.13% Ni with diesel fuel-crude tall oil-sulfonate collectors produces concentrates assaying 15% Mn, 0.6% Co, and 0.3% Ni with recoveries of 89-95% while removing 62% of the feed weight.

Jan 1, 1990

By C. Villa Diniz

It is proposed that battery grade Mn02 can be produced directly from a manganese ore from Azul Mine in Brazil, by leaching with HCI to remove heavy metals selectively. We are working to find a way of selectively separating Cu, Ni, Co, Pb and Fe from the resulting acidic manganese chloride solution, to detoxify it and produce marketable chloride solution. Chelating ion exchange resins are proving more promising for this separation than solvent extraction with commercially available reagents. Results from batch and column ion exchange tests that characterize the behavior of copper, nickel, cobalt, lead and iron are reported.

Jan 1, 1999

By Tuanhui Wang, Qiwei Wang, Quanrui Liu, Jianhui Xu, Chao Wang, Yu Liu, Yuefeng Li

Rockburst is a highly destructive geological hazard that can cause casualties and equipment damage. To achieve highaccuracy discrimination of rockburst intensity, this article proposes an improved model that addresses the inefficient maximum membership principle used in traditional rockburst fuzzy evaluation models. The stress coefficient σθ/σc, brittleness coefficient σc/σt, and elastic deformation energy index Wet are selected as evaluation indicators for rockburst classification. Subjective and objective weights are obtained using the Delphi method and entropy weight method (EWM). Three types of membership function distribution forms are then used to obtain the membership degrees of each indicator to rockburst grades: trapezoidal membership function (TMF), normal membership function (NMF), and quadratic parabolic membership function (QPMF). Finally, six traditional models and six improved models are established using the maximum membership principle (MMP) and weighted average-maximum membership principle combination evaluation principle (WMP), respectively. Based on the analysis of 100 sets of rockburst field data, the accuracy, precision, recall, and F1-score of the improved evaluation model are increased by 11.3%, 0.097, 0.068, and 0.089, respectively, compared to the traditional model. The Delphi-NMF-WMP model is selected as the best model, with four performance indices reaching 97.0%, 0.979, 0.979, and 0.978. The best model is applied to evaluate the rockburst intensity of the Cangling Tunnel, Dongguashan Copper Mine, and Jiangbian Hydropower Station Diversion Tunnel, with evaluation results consistent with the actual situation, demonstrating the reliability and scientificity of the model.

Feb 28, 2024

By R. L. Loofbourow

The Sunro Copper Mine is near the south coast of Vancouver Island about 35 miles west of Victoria. Failure of the roof of a large open stope let a good sized mountain stream into the mine. Broken are, boulders and sand were washed into the underground mill and out through a 7 800-foot adit. The adit became plugged; water burst out an a ridge above the adit, washing out the portal and o trestle by which it was reached, Rock and ore are strong but several systems of steep, pronounced but generally tight fractures are found on and parallel to the walls of the orebody. The stope was started from a slusher drift 390 feet below the bed of the River and brought up to an elevation 155 feet below the River by blasting vertical and horizontal rings of longholes in the nearly vertical orebody. Mining was stopped there and five months were given to grouting and bolting the pillar under the bed of the River, During this time and for several months thereafter sloughing increased the width, length and height of the stope. At the last known observation the stope was 77 to 96 feet wide, 185 feet long and the highest point of the domed back was only 55 feet below the River. The flooding took no lives. In other respects, however, it might be difficult to find in mining lore o more savage example of the application of "Murphy's Laws".

Jan 1, 1968

By Jianbo Hu, Gang Han, Tao Zheng, Junfeng Jiang, Rui Su, Qihua Zhao

The rock quality designation (RQD) is a commonly used index for the classification and evaluation of rock mass quality and is widely adopted in mining and geological engineering. The traditional method of obtaining RQD still requires manual measurement of core length and calculation of RQD, which is inefficient. To address this problem, we propose a framework for drilling core image segmentation and RQD estimation from digital images of cores in core boxes based on the deep learning algorithm. The proposed framework is generated by combining the Mask Region-Based Convolutional Neural Networks (Mask R-CNN) instance segmentation algorithm, the U-Shaped Convolutional Neural Networks (U-Net) semantic segmentation algorithm, and the image processing functions of the Open Source Computer Vision Library (OpenCV). To demonstrate the accuracy of the proposed method, seven boreholes in the Xiushuihe vanadium-titanium magnetite mine, located in the Sichuan Province, China, were used as the case study. According to the comparison of the manual measurements and calculations of the cores taken from seven boreholes used to conduct this study, the framework can record the length of the drill cores and calculate RQD within an average error rate of 3.42%, while it saves about 85% of the working time. The results illustrate that the proposed framework enhances the efficiency of RQD calculation while satisfying the engineering requirements.

Jul 31, 2023

By Ting Ren, Jon Roberts, Zhongbei Li, Ming Qiao, Jianming Wu

Spontaneous heating of coal continues to present a health and safety hazard in underground coal mines. The influence of seam gas composition on gas flow dynamics and distribution characteristics in the active longwall goaf has not been studied in-depth, and corresponding effective proactive goaf inertization strategies for preventing potential spontaneous heating from occurring have limited investigation. To advance this knowledge, an 80-m-height goaf model was constructed and developed based on specific conditions of an Australian underground coal mine, and onsite gas monitoring data was collated to verify base model results, which allowed for various scenarios of seam gas composition to be simulated and investigated with confidence. This study involved modeling five different gas composition scenarios for the goaf atmosphere, namely, 100% CO2 (case 1), 80% CO2 and 20% CH4 (case 2), 50% CO2 and 50% CH4 (case 3), 20% CO2 and 80% CH4 (case 4), and 100% CH4 (case 5). Simulation results show that O2 is primarily distributed at the middle and upper part of the CO2- dominant goaf model, while it is mainly layered at the floor level of the CH4- dominant goaf model. N2 is superior to CO2 in the goaf inertization for the CO2- dominant goaf model, whereas CO2 performs better than N2 for the CH4- dominant goaf model. The optimal inert gas flowrates for case 1 to case 5 are 1.5, 1.75, 0.75, 0.5, and 1.0 m3/ s, and the oxidation zone area is reduced by 55.76%, 67.21%, 58.04%, 78.17%, and 81.82%, respectively. The simulation results allow for increased insight and understanding of the gas distribution patterns in the active goaf with different seam gas composition and the development of corresponding proactive goaf inertization practices, thus minimizing potential spontaneous-heating-related hazards and improving mining safety.

Sep 26, 2023

By A. Yadav, B. Behera, G. S. P. Singh

The size of chain pillars in the Indian geo-mining conditions is primarily decided in accordance with the regulatory provisions. These provisions are of little help for deep longwall workings, exceeding the cover depth of 360 m. Furthermore, these provisions are primarily meant to support pillars in bord and pillar workings. They may not be suitable for the chain pillars owing to a significant difference in layouts and functional requirements. Hence, it is imperative to develop a method to evaluate the stability of the chain pillar considering the complex loading and geo-mining conditions. To this end, a machine learning-based model was developed in this study to assess the stability of the chain pillars under high depth of cover considering the field-representative conditions. The data for this work was generated by conducting a parametric study using a field-validated numerical model. The strength and deformability parameters of the caved, fractured, and continuous deformation zones were established by calibrating the numerical model outcomes against the site-specific field observations. The developed ML model was used to evaluate the influence of pillar width, pillar height, cover depth, abutment angle, face length, coal strength, moduli ratio of the roof and floor strata to the coal seam, and the elastic modulus and unit weight of the overburden on the chain pillar stability. An interesting finding of this study showed that the factor of safety of the chain pillar increased with the increasing abutment angle, which may be indicative of the confining effect of the abutment angle on the pillar. Eventually, the ML model was verified by comparing its outcomes with the calibrated numerical model for a typical longwall working from Indian geo-mining conditions.

Oct 18, 2023

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By S. R. Brown

A number of relatively recent factors associated with the design of new metallurgical processing plants have made the effective training of operators a requirement for a successful start-up. Some of these factors include large capital investment in a minimum of processing lines, highly complex process control systems, and stringent regulations on plant effluent, to name a few. More than ever, operating mistakes during the start-up phase can lead to substantial delays in achieving design production, as well as problems with government authorities if permit limits are exceeded. The only way to assure your return on plant investment is to ensure new plant operators have the knowledge to properly run the plant from the outset. A comprehensive set of operating manuals specifically targeted for plant operators and foreman, written by experienced operating personnel, is the only effective way to provide the necessary information for start-up-related training.

Jan 1, 1995

By Taghi Sharizadeh, MAURICE SUNKPAL, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards that have adverse effects on the mine workers. The very nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources including autocompression, equipment, and heat from strata. This study investigated the effects of clothing insulation and acclimation on the thermal comfort ofmineworkers who are exposed to heat in underground working environments. Several clothing ensembles have been considered to analyze the effect of the thermal resistance of clothing on the thermal comfort of workers. To investigate the impact of the clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an 8-h shift. Parametric analyses were subsequently performed using an already developed thermal comfort model using MATLAB software. The results demonstrate that clothing insulation has a significant effect on the thermal comfort of mine workers. Increase in the clothing insulation decreases the maximum allowable exposure time of mine workers. This is especially true for the new and non-acclimated workers. Since acclimatized workers can tolerate a higher level of the dehydration and are capable of losing more water by sweat per shift, the maximum allowable exposure time for the acclimated workers are higher than non-acclimated workers. These analyses have shown that acclimated workers can have more continuous work per shift compared with non-acclimated workers. For example, in an environmental condition with clothing that a nonacclimated worker cannot work more than 5 h, an acclimated worker can work a full 8-h shift.

Jun 29, 2020

By C. Garcia, A. Potulska, J. J. Opazo, T. Comi

"The Sierra Gorda SCM sulfide ore processing plant began commissioning in the third quarter of 2014. Located in the Atacama Desert in northern Chile, the project is an open pit mine and Copper-Molybdenum processing plant is one of the most highly-instrumented operations in the world. It is the first hard rock operation in Chile and the second in South America to utilize HPGR technology. It is a significant Molybdenum resource especially in the first five years and the Molybdenum separation plant is complex. Designed to process up to 60 million lbs. of fine Molybdenum per year, it uses the latest technology and equipment to ensure superior recovery and product quality. It also has gas handling and alarm systems to fulfil the Company’s vision of “Zero Harm”. This paper discusses the overall operation and issues relating to the concentrator start-up. These include a review of the mineral processing design, the unified process control center and management information systems, and the correlation of geological and metallurgical performance data (mine-to-mill) for use in anticipating and preparing for treatment of diverse ore deliveries. INTRODUCTION Sierra Gorda SCM is a joint venture partnership with KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining, and Sumitomo Corporation (Japan) operating in northern Chile. The Sierra Gorda open pit mine and Copper-Molybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, well-instrumented mine in Chile. This paper contains a general review of the project including geology and history. This was a very fast-track project going from greenfield site acquisition to mill start-up in 10 years. Highly-experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied. The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (see Figure 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km from the village of Sierra Gorda at an elevation of approximately 1,700 m above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic, and Escondida, to name a few."

Jan 1, 2015

By Abdelaziz Baçaoui, Imane Aarab, Abdelrani Yaacoubi, Khalid El Amari, Abderahman Etahiri

Phosphate ores upgraded by flotation are widely used as vital raw materials for the sustainable production of phosphate fertilizers to maintain the food supply. High-grade phosphate reserves become more and more depleted. Low-grade phosphate mining and processing are in the spotlight of the fertilizer industries to cope with the exponential growth in the world’s population and meet the increased demand for fertilizers. As part of a series of research works conducted within a major project aiming at upgrading a low-grade phosphate ore never-exploited before, the present work endeavors to optimize the flotation of this ore using the response surface method (RSM) as a follow-up of a screening study. Unveiling new insights on such a strategy paved the way for improving flotation performances. This work demonstrated that an optimum 30.18% P2O5 with 88.07% recovery was achieved using 63.10 g/t of sodium alginate (NaAL) and 2484.72 g/t of sodium oleate (NaOL) at pH 11.40. This maximum was contrasted with a new formulation of fatty acids (FAM). The 30.76% P2O5 grade with a recovery of 89.72% was attained using 50.94 g/t of NaAL and 1455.40 g/t of FAM at pH 11.68. FAM collector markedly outperformed NaOL at low concentrations proving the efficiency of synergists.

Dec 7, 2022

By Osvaldo A. Bascur

Standards and technology for bringing information to the desktop have greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure cooperative effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and database layers are emerging in successful client/server applications, the three-tier architecture.

Jan 1, 1996

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. High-grade Transvaal chalcopyrite was neutron irradiated in a TRIGA reactor to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes during which time significant anomalies were observed. First, an initial period of rapid dissolution lasting a few minutes; second, an arrest or "plateau" region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effect of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured. The initial rate data were correlated by considering the rapid reaction to be due to the dissolution of surface oxidation products or the formation of an iron depleted surface layer. The data for the second slower reaction have been explained to be due

Jan 1, 1972

By R. L. Grayson, R. C. Althouse, L. A. Layne, M. J. Klishis

Introduction The researchers combine a detailed microanalysis of accident data and roof bolting field observations to develop new and meaningful risk indices for the roof bolter job classification. These indices incorporate information that has not been used in traditional measures of risk. The significant parameters that these new indices incorporate are the total number of accidents occurring within a particular work activity, the amount of time a miner usually spends performing the work activities in which the accidents occurred, and the average severity of the injuries incurred in the accidents. Being specific for a particular job, they aid comparisons among work tasks performed in the bolting cycle. The indices' specificity provide anew basis for reexamination of training and operational development of miners for specific jobs. Microanalysis The roof bolting microanalysis was performed by examining the empirical data and written summaries for all bolting accidents reported in the West Virginia Safety Information System (WVSIS) for the years 1983-1987. The WVSIS database contained more than 15,000 accident narratives. The microanalysis of bolting accidents covered 2083 reported personal injuries (RPIs). This large number of injuries, performed at an industry-wide level, provides a broad picture of the nature of roof bolting injuries. The analysis focuses on the activities associated with the cyclical routines of the roof bolting process. For this analysis, roof bolting tasks were categorized into work routines based on the sequence of work activities performed by roof bolters. Four work routines were identified within the overall bolting cycle. And these routines comprised 70% (1217) of all roof bolting accidents at the face. The routines include: face area preparation; tramming, positioning and setting the automated temporary roof support (ATRS); drilling holes; and installing bolts. The types of injuries most common within a routine and the average severity of those RPIs were also identified. Table 1 gives a breakdown of the percentage of accidents by the bolting routines. Another 19% of the roof bolting RPIs cannot be classified in a particular routine because of the vagueness of the narratives. However, it was clear that these accidents involved drilling holes or installing bolts. These results are consistent with previous research. It identified drilling and bolting, followed by tramming, as the most frequent sources of injuries (Helander, Krohn & Curtain, 1983). [Table 1-Accidents by bolting routines at the face Accidents Bolting routine Percent Number Face area preparation 18.2 222 Tram, position, ATRS 23.3 284 Drilling holes 34.2 416 Installing bolts 24.2 295 Total 1217] Roof bolter operators were involved in 82% (1706) of the 2083 accidents. The RPIs incurred by classified roof bolters occurred largely on working sections (95%) and at the face area on the working section (75%). Approximately 23% of the 1706 roof bolter RPIs occurred during tasks which were not part of the bolting cycle. These included belt utility work, providing supplies and section moves. Miners in other job classifications who were involved in roof bolting accidents accounted for the remaining 18% of the 2083 roof bolting RPIs. Among this group were section utility men and general laborers (41%), section machine operators (38%), and electricians and mechanics (11%). Another 9% were performing on-section supervisory functions. Face area preparation Face area preparation work led to a substantial number of injuries, although it accounted for the lowest number of injuries of the four routines. Several tasks were associated with the injuries incurred in this routine. Table 2 shows the percentage of injuries associated with face area preparation. [Table 2- Accidents occurring during face area preparation 26.6% Setting temporary and supplemental supports 24.8% Scaling roof and ribs 21.2% Installing ventilation devices 15.8% Handling supplies and materials 11.6% Miscellaneous tasks] The injuries commonly involved overexertion and 'struck by' falling coal and rock. Handling materials often led to overexertion injuries. Nearly 66% of the scaling-related injuries and about 33% of the injuries incurred during the setting of temporary supports involved 'strikes' by equipment, materials, top and rib. Tramming, positioning and setting the ATRS During tramming operations, workers were often struck by components of the machine and hit by loose roof and rib. Poor footing also led to slips, sometimes against the moving machinery. Table 3 gives a breakdown of accidents in this routine. Control levers were a significant problem in this routine.

Jan 1, 1993

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of fluorspar from 35 domestic and 50 foreign, mines and deposits in 13 countries. Only 6 domestic properties are considered to be economic reserves, as 29 domestic deposits were found to have an average total cost of production that was uneconomical at a breakeven (0 pct) DCFROR. The 50 foreign properties evaluated were selected to represent at least 85 pct of the known demonstrated fluorspar resources located in market economy countries and China. All evaluated foreign operations were found to be economic to marginally economic in January 1984 dollars. World demonstrated ore reserves of 344 million metric tons (mt) containing 123 million mt of CaF2 were evaluated for the 56 operations. Average total costs needed to cover all costs over the life of each operation were determined for all recoverable fluorspar products. Comparisons of mining, beneficiation, and transportation costs per mt of fluorspar concentrate illustrate advantages between countries. Of the three largest producing countries, China, with its high-grade, low-cost operations had the lowest weighted average total cost of production ($38/mt concentrate). Mexico was next at $54/mt concentrate, and South Africa needed an average of $90/mt of concentrate to cover all costs of production for its low grade deposits.

Jan 1, 1985

By F. W. Jessen

The production of salt through brining operations and the recovery of potash salts by means of solution with water constitute, in large measure, processes which have been used for many years. And although the salt industry has utilized dissolution techniques for years and years it has been only recently that a better understanding of the mechanism of solution has emerged. Greater adaptability of solution mining processes for recovery of valuable salts from ore bodies found at greater and greater depth has resulted in increased adoption of such methods. Because of the high costs of mining in beds of limited thickness, modifications probable when extracting mixed halites, and restrictions (mostly self-imposed) regarding the extent of cavern development to minimize or eliminate subsidence more information is needed on the solution mechanism. It is the purpose of this paper to present the fundamental aspects of the problem of total solution of salts and to point out the developments of certain solution mining techniques.

Jan 1, 1971