Search Documents

By Robert L. Marovelli

The major mining health and safety problems of concern to United States Government and private industry researchers in 1981 included the difficulty experienced by longwall operators in complying with the Federal 2 .0-mg/m3 respirable dust standard, the accident rate associated with falls of ground and materials handling hazards, and the upsurge in the incidence of disasters after the steady decline in recent years. Although the many mines and manufacturing companies involved in the research projects to be described are not specifically identified, it is important to note their significant involvement. This is not by way of acknowledgement, but rather to establish that these projects, using mostly Federal funds, represent close cooperation between the U.S. Government and the mining industry. The ongoing work to be described on the development of critical longwall dust control technology is a classic example of Government-industry participation through the phases of problem identification, planning, cost-sharing, and implement at ion.

Jan 1, 1982

By I. B. Tulu, M. M. Sears

"In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial, yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground fall related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground fall related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 21 longwall mines were visited, representing about 40% of the currently active longwall mines in 4 of the 5 major US longwall producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. The results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries. INTRODUCTION Maintaining ground stability in gateroad entries is essential for longwall productivity and safety (Campoli, 2015). In 2015, 148 unintentional roof falls were reported in US longwall mines. About 34% of these resulted in mineworker injuries. Safety considerations not only include injury from roof and rib falls but also egress from the longwall face during an emergency (Mucho et al., 1999). Over the past 30 years, a number of researchers have studied longwall tailgate support performance (Mirabile, 2015). This research aims to take a snapshot of the ground support installed in modern US longwall mines and provide a supplement and update to the overview provided by Barczak (2005). This will provide a framework for future research into improving gateroad support systems. BACKGROUND Large unplanned roof falls at or above the primary support or those impeding travel and/or ventilation must be reported to the Mine Safety and Health Administration (MSHA). Reportable roof falls, normalized based on production in million metric tons, generally relate to the amount of roof exposed during the mining process (Pappas and Mark, 2012) and provide an evidence-based statistical background for this review of current support practices. Figure 1 shows the reportable roof fall rate in US underground longwall mines for the period 2006-2015 (MSHA, 2016). Over the past decade, roof fall rates have shown a gradual decrease with numbers now at a rate nearly half of what was observed just five years ago. However, over the past few years, roof fall rates in US longwall mines appear to have stagnated at levels just over 1 per 2,000,000 tonnes mined."

Jan 1, 2017

By Paul R. Weber

Open-pit mines are constructed in materials characterized by the complete range of geologic materials from the most recent alluvial sediments to hard intact crystalline rock. The determination of stable slopes in recent alluvium is in the realm of soil mechanics, an established engineering discipline, well founded on theoretical development and years of substantiating experience. The analytical tools of the soils engineer are chiefly derived from continuum mechanics wherein load-deformation response is governed by mass properties of the substance. At the other end of the spectrum, slopes in hard unweathered rock can generally be analyzed in a straightforward manner by the methods of discontinuum mechanics wherein the properties and orientations of joints control the response of the material. This approach is exemplified by the classical work of Terzaghi (1962). In between these two extremes is a gray area of material types which are composed of stiff soil and incompetent rock. This area is of importance to the mining engineer, since a large portion of open-pit mines is excavated wholly or in part into incompetent rock. This paper describes an approach to pit slope design in incompetent rock in which the material behaves essentially as a continuum. A wide range of geologic materials from stiff soil to poorly indurated sandstone and shale to crushed or weathered crystalline rock appear to fit in this category. These materials all possess certain mechanical properties which must be accounted for in a realistic assessment of slope stability. These properties include nonlinearity, s tress -dependency, and inelasticity. Further considerations involve residual stresses and time-dependent seepage pressures where groundwa.ter is present.

Jan 1, 1971

By M. T. Ityokumbul

The use of yield index, the product of the yield and gangue rejection, for the optimization of separation processes is presented. The characteristics of the yield index are contrasted with separation efficiency calculations and applied to laboratory froth flotation and washability data. Data from continuous froth flotation tests conducted to "optimize" froth flotation using process optimization software were also evaluated with the yield index procedure.

Jan 1, 1997

By E. J. Haas, K. A. Rost

"This study sought to identify changes in continuous mining machine (CMM) operators’ risk perception and risk behaviors as a result of adding a proximity detection system (PDS) into their environment. To accomplish this research task, 9 CMM operators from 5 locations were interviewed. Interviews were thematically analyzed for constructs including patterns in risk perception and behavior before and after PDS integration and the process of adapting to the PDS. Operators discussed standing in the red zone less than they did before using the PDS; however, they also discussed other risky decisions they made while learning how to operate their CMM with the PDS technology such as “cheating” the technology and working faster to meet production goals. The process of relearning job tasks with technology and unintended behaviors as a result of that relearning process need to be taken into account when introducing new technology into the mine environment. The study results show an in-depth view of mine workers’ perspectives and how their job tasks and environment could be or are affected when learning how to use new technology that are relevant to companies and mine operators when introducing new technology into the mine environment. INTRODUCTION Established “red zones” can help prevent striking and pinning incidents by providing guidance to continuous mining machine (CMM) operators about where they should stand and not stand while operating a CMM. Although red zones influence operator placement positions, these guidelines are not foolproof safety mechanisms. Depending on the job task and circumstances of the mine environment, a CMM operator may unintentionally or intentionally stand in a red zone. For example, CMM operators may work in close proximity to their CMM for better visual attention cues and the ability to work at a higher rate of production [1-3]. To further enhance protection and prevent collisions between vehicles and mine workers, a proximity detection system (PDS) was developed for the industry. The PDS determines an individual’s position relative to a specific piece of machinery, issues visual and/or audible warnings to the mine worker to change positions, and, if necessary, disables machine motion [4]. The introduction of new technology within other sectors has been identified as a factor that influences work decisions. Specifically, previous research demonstrates that when technology debuts there can be an initial intrinsic risk perceived among users about how the technology will interact with their current environment and behaviors; however, these ambiguities, including the possible risks and benefits, are seldom studied [5]. Some research suggests that the constant presence of technology can disrupt situation awareness and decision-making capabilities by increasing worker responsibilities and worker cognitive demands [6-8]. Further, if workers’ perceived risks both with and without technology are misjudged, unsafe decisions that result in human error and injury may be more likely [9-11]. Although these statements are provided within a broad contextual framework, they support the need to study how technology is perceived among end users in their own environment. Because research about technological impact on worker behaviors has suggested both positive and negative consequences of technology, this issue is worth addressing in the mining industry. Specifically, research has not determined whether CMM operators view their placement choices in the red zone as safe or risky and what effect PDS technology has, if any, on risk perception and subsequent risk behavior."

Jan 1, 2015

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous ones because of their fatality records. Statistical testing of 1993 West Virginia safety and production data indicated that the most efficient WV mines were not the safest ones, considering correlations between the severity measure and tons per employee-hour, except for very small mines. This paper will present the results of an extended analysis of WV mine safety using 1993 and 1996 data, concluding with the method used to suggest current priorities for focusing interventions.

Jan 1, 1998

By S. Uihteenmaki

Pyhasalmi is a massive sulfide orebody located in central Finland. The mine has been in operation since 1962. The flotation concentrator produces Cu, Zn, Pb and pyrite concentrates. The plant has used an on-stream analyzer for process control since 1968. The original analyzer has overlived a few generations of minicomputers, but the analytical parts are essentially unchanged. The on-stream analyzer is a critical component in plant process control system, which has made Pyhasaltni one of the pioneers in the art of computer control and optimization of flotation plants. The paper summarizes the experiences gained from the use of the high performance elemental analyzer system and the proven benefits from the use of on-stream analyzers at a complex sulfide flotation. The aging analyzer is approaching the end of its useful life. A new state of the art analyzer system is undergoing testing at Pyhasalmi.

Jan 1, 1999

By James Lett

The role of pre-conditioning in a caving operation has multiple benefits, ranging from assisting with improved caveability, normalising fragmentation and improving draw point hang-up frequency. At Newcrest Mining’s Cadia Operations, both the Ridgeway Deeps block cave the Cadia East Panel Cave have utilised pre-conditioning using hydraulic fracturing. Seismic response data inside and outside the pre-conditioned volume show the benefit of treating the full caving block. Cadia East has further developed pre-conditioning to mitigate developing seismic hazards associated with major structures (fault-slip events) and managing mine-wide seismic hazards in new caving operations where the potential for large damaging seismic events exists due to high stresses and hard competent rockmasses. A case study reviewing the impact of pre-conditioning to mitigate seismic hazard associated with fault slip is presented. Cadia East operation undertook a targeted hydraulic fracturing program and reduced the overall number of large events as an example of the benefits of pre-conditioning. This paper will review the application of Hydraulic Fracturing at Cadia and discuss the geotechnical and seismological parameters of seismic events that occur within and outside of pre-conditioned rockmass volumes to demonstrate the benefits that Hydraulic Fracturing bring to future caving operations.

Apr 26, 2022

The Putnam Coal Mine, at design capacity, will be the third largest underground bituminous coal mine in the world and will feature the world's longest single flight belt conveyor. Construction is now in process; initial mining will commence in early 1969 and design capacity will be reached in 1971. I'm Jerry Workman, Assistant Mining Manager for the Coal Group of the Mining and Metals Division of Union Carbide Corporation, and I am acting as Project Manager for installation and start-up of the Putnam Mine. The Putnam Coal Mine reserves are located in south-central West Virginia and contain approximately 27,000 acres of prime Pittsburgh No. 8 coal; reserves are sufficient to support a 3.5 MM tons per year operation for over 30 years. The mine portal area is located some six miles inland from the Kanawha River. The river loading facility is located approximately 156 miles by way of river from the market.

Jan 1, 1968

By Robert C. Maxton

The foundry industry is a basic source of structural component for all industry. Millions of tons of castings are produced annually in both ferrous and nonferrous alloys. These castings are subjected to a wide variety of heat treatments, finishing techniques, mechanical tests and machining operations. Through all of these steps the quality of the casting is of paramount importance to the end use of the product. The Quality Assurance Program at Minneapolis Electric Steel Castings Company is designed and established to provide a superior product for both original equipment manufacturers and the mining industry.

Jan 1, 1982

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By Jianbo Hu, Tao Zheng, Zhao Qihua, Rui Su

Rock mass discontinuities play a significant role in evaluating the stability of rock slopes. It is necessary to collect and analyze these discontinuities to fully understand the mechanical and deformational behaviors of rock masses. Based on the digital images of some slope faces, this paper proposes a framework based on machine learning for detecting and extracting discontinuities. First, digital images and photo poses are combined, the original scene is reconstructed, and 3D point cloud data are obtained. All captured point clouds can be mapped with each image by the direct linear transformation algorithm. Next, the detection machine learning algorithm is used to segment rock mass discontinuities on 2D digital images. Finally, based on the mapping relationship, the 2D digital images that were segmented are transformed into 3D point cloud data. The geometric parameters of the corresponding discontinuities can be extracted by the DBSCAN and the Skmeans algorithm and the characterization of specific rules. The proposed framework was evaluated utilizing a quantity of slope digital images in the Yebatan hydropower under construction, located in Sichuan Province, China, as a case study. The results illustrate that most deviations are less than 10° for the dip direction and dip angle, which verifies the reliability of the proposed framework and maintains acceptable measurement accuracy.

Nov 6, 2022

By W. G. Pariseau

"BACKGROUND Strata mechanics of three underground coal mines in central Utah were recently studied using a specialized finite element technique [1, 2, 3, 4]. The purpose of these studies was to examine relationships between mining and related seismicity. The longwall mining method was predominant, but room and pillar mining and barrier pillar mining were also used in the mines studied. In every case, high correlation between face advance and seismicity was observed. The specialized finite element technique allows for whole mine subsidence estimation at a kilometer scale and for stress concentration at a meter scale near a working face. Comparisons of observed mine subsidence with model subsidence allows for model verification and justifies detailed analysis of the evolution of stress at seam level. Yielding is expected near a longwall panel face and as the face is advanced the extent of yielding is expected to increase. The total number of element failures in a finite element mine model also increases, so a high correlation with associated seismicity, say, event count, is not so surprising. A brief review of recent coal mine studies in Utah is presented in the sequel. The procedures are given in some detail in application to trona mining. COAL MINES The analysis procedure begins with the geologic column and proceeds to specification of strata properties including elastic moduli and strengths. Joints are an integral part of the geologic model and joint set specifications include dip direction, dip, spacing, stiffness and strength. Spatial variability of strata properties in situ may be taken into account during analysis. Topography is important, especially to Utah coal mines that are developed from outcrop in regions of high relief. Mesh generation follows specification of data input. Finite element analysis is next, followed by reporting of results. In this regard, all finite element computations are based on first principles. No model “calibration” is done that involves adjusting computer input to obtain a fit to mine measurements such as subsidence profiles. Figure 1 illustrates the concept of a dual node – dual mesh finite element concept. Dual nodes are roof and floor nodes in mined areas. These nodes replace the seam. The dual mesh is a much refined mesh with displacement boundary conditions obtained from the big mesh and thus replaces the effect of mining in the region outside the dual mesh. The refined dual mesh allows for details of stress, strain and displacement near a working face of interest. Strata Properties Strata properties include elastic moduli and strengths of intact rock between joints and joint stiffness and strength for each joint set present. Both properties sets may be obtained from laboratory test data, although testing joints poses a sampling problem in the field. The statistical variability observed in laboratory test data, say, in unconfined compressive strength tests is often characterized by much variation. In fact, the coefficient of variation, ratio of standard deviation to mean, is often greater than 35 percent. When sample values are mapped back to the mine location, one may observe spatial variability as properties vary from place to place as shown in Figure 2. Spatial variability may be incorporated into a finite element analysis with probabilistic assignment of properties to elements in accordance with measured variability. The result is a more realistic model of rock in situ."

Jan 1, 2017

By Debasis Barman

TBM (TBM) mining in urban areas particularly under low overburden is a big challenge to design and excavate. During excavation of the Lucknow Metro project, in Uttar Pradesh, India the metro authorities encountered a design stretch where the TBM had to cross a sewer canal crossing of 15 m length under overburden of less than 1 m. Not only the stability of TBM due to uplift was of concern but also the stability of both banks. Most structures on the canal banks were non-engineered structures whose stability due to vibration of TBM was also of concern. Due to these risks, a method was proposed that met stability requirements for both ground and superstructures. The design was practical and cost effective to construct, and a collaborative exercise between the client, contractor and designer that took approximately 18 months to implement.

Jun 13, 2023

By Qingwen Shi, Gang Xu, Shuwen Wang, Brijes Mishra

Pressure relief borehole is one of the most effective methods to treat coal burst in deep-buried coal seams. However, due to the large amount of randomly distributed fractures in the coal body and the varying stress environments in underground coal mines, there is no practical method to assess relief boreholes by far, which brings problems for borehole design and construction. This study focuses on the assessment of relief boreholes in a single driving entry wherein the impact of mining panels on relief boreholes is eliminated. A practical method, focusing on field monitoring of borehole deformation with a new device, is developed to evaluate the single driving entry’s relief boreholes. This method is applied to a Chinese coal mine. The application results showed that the convergence process of the boreholes showed a three-phase characteristic. Phase one involves the fastest deformation, reaching up to 8% in the first 3 to 4 days. Phase two lasts longer and converges more, reaching up to 30% in 4 months. Phase three stays balanced until the excavating face moves. The three-phase characteristic indicates that a large diameter of the borehole ensures relief efficiency because the borehole provides adequate space for deformation throughout its life span. In addition, it is verified that long boreholes and slow footage improve relief efficiency by providing adequate time for the boreholes to work. The application proposes that boreholes in the test coal mine need to be drilled larger and longer for optimization.

Oct 19, 2021

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By J. P. McCluskey

The effects of air quality regulations passed in the last few years have been felt in a more pervasive way by the electric utility industry than by perhaps any other industry. I'm referring especially to those regulations dealing with the control of air emissions from stationary sources, and those specifying the quality of fuel used. Particularly, I would like to describe some of the effects that these regulations have had on the Commonwealth Edison Company. To put the subject into perspective, a brief descrip¬tion of the company will be presented first. Then, a historical outline of some of the efforts at control of electric generating station emissions will be described. Following this will be an indication of the Company's response to early State and local regulations prompted by the growing pressure for stringent envi¬ronmental control. Finally, the Company's plans to achieve com¬pliance with the most recent, Federally approved, State of Illinois regulations will be summarized.

Jan 1, 1973

By David D. DiPonio, John DiPonio, Roger Van Omen

The greatest opportunity to attain the most favorable prices for underground construction projects occurs during the competitive bidding period. The Owner, Engineer, and Contractor need to have a thorough understanding of the project’s design concept, how it is going to be built, and what it is going to cost. This paper presents the opinions of three engineering professionals who are well established in their sectors of heavy civil underground public works construction. This paper will outline and summarize the considerations that the three principal contracting parties of Owner, Engineer, and Contractor need to make to obtain good price quotes at the time of bids.

Jan 1, 2005

Computer programs commonly used to simulate mining operations generally require a fair amount of data. The common data input methods have been by either creating an ASCII data file or answering numerous questions during the data input phase. Both methods of data entry are tedious, time consuming, and inflexible. A screen handling system has been developed to drive FORTRAN-77 application software for the MS-DOS environment. The system utilizes keyboard functions with an aid of extended ANSI codes. It also allows a multi-view input data entries.

Jan 1, 1990

By Duane A. Smith

Introduction From the days of the Spanish in the eighteenth century, Colorado's San Juan mining district has attracted miners and public interest. The Spanish left behind names - San Juans, La Plata, Animas, legends of lost mines, and the remains of a few scattered mining operations. They came, but did not stay. Again in 1860-61, as a spinoff of the Pike's Peak gold rush, prospectors climbed the mountains and descended into the canyons searching for gold. They found some, not enough to convince them to remain and confront the isolation, often hostile environment and the Utes, who rightfully felt this to be their home. Not until the 1870s did miners come to stay. In their wake little camps grew in the high valleys and squeezed into narrow canyons. Nowhere else in Colorado were there more rugged mountains, a higher average elevation, nor a climate that one old Swede said was "three months of mighty late fall and nine months of winter." The San Juans proved eventually to be a mineral treasure chest. At the moment, however, the prospectors sought gold. Then they discovered silver deposits and the first rush was on. It got started just in time to be completely overcome by the Leadville excitement. At Leadville, investors almost fell over themselves to buy claims and stock in the hopes of becoming another millionaire like Leadville's own Horace Tabor. The San Juaners could only look from the sidelines and speculate how it might have been had fate been kinder. Fate was seldom kind, as these pioneers quickly discovered. From the mid-1870s on, the San Juaners wrestled with some major problems. And the fate of their district rode in the balance. The problems they faced were similar to those of other Colorado districts, compounded by their geographic isolation. Every mining district needed the best transportation system available, experienced investors combined with sound investment, and mineral reserves to develop. The San Juans offered the last in abundance. It was hoped the first two would appear. Railroads - much needed transportation link Nothing was more desired than railroad connections, the penultimate nineteenth century form of transportation. Colorado's own, the Denver & Rio Grande, resolved the issue with its mountain-hugging narrow gauge. As early as the mid-1870s, the D&RG dreamed of tapping this potentially lucrative market in southwestern Colorado. A national economic depression and then the Leadville silver excitement prevented immediate construction. Not until 1879-80 did survey crews start work.

Jan 2, 1988