Search Documents

By Ralph van Rijswick, Erik Vlot

"Anglo American operates 18 Weir GEHO piston diaphragm pumps (PD) in the two pump stations of the 52-km (32-mile) long Minas Rio iron ore concentrate pipeline. The pipeline is designed to transport 26.5 Mt/a (29.2 million stpy) of concentrate from the mine to the export terminal at the coast.During the commissioning of the pipeline in the fall of 2014, high pressure pulsation levels were experienced, with peak-to-peak levels as high as 20 bar. Based on pressure readings it was concluded that hydraulic resonances were present in the system, which were excited by the third and sixth harmonic of the flow pulsation generated by the pumps.Based on this observation, Weir Minerals Netherlands, manufacturer of GEHO PD slurry pumps, recommended installing a phase shift controller that controls the phase shift between the crankshafts of the individual pumps, thereby minimizing the effect of the hydraulic resonances.GEHO piston diaphragm pumps and pressure pulsation analysisPiston diaphragm pumps are used worldwide to transport abrasive and/or aggressive slurries against high discharge pressures in the mining, mineral processing and power industries. The basic operating principle of a piston diaphragm pump is shown in Fig. 1.A crankshaft is driven by an external electric motor via a gearbox. The crank mechanism transfers the rotating motion of the crankshaft into a reciprocating motion of the piston. The piston displaces a hydraulic fluid, called the propeling liquid, which displaces an elastic rubber diaphragm. When the piston moves to the right, the pressure in the pump chamber drops below the suction pressure and the nonreturn valve on the suction side will open, allowing the pumped fluid to flow into the pump chamber. When the piston moves to the left, the fluid is compressed, and when the pump chamber pressure rises above the pipeline pressure, the nonreturn valve on the discharge side will open allowing a displacement of fluid into the discharge line. The main objective of the diaphragm is to isolate the piston and the drive mechanism from the abrasive and/or aggressive fluid and create a hermetic seal between the pumped fluid and the ambient environment. Piston diaphragm pumps as shown in Fig. 1 are among the largest positive displacement pumps in the world and have been produced with stroke volumes of up to 100 L (26 gal) per pump chamber for flow rates up to 800 m3/h, discharge pressures up to 250 bar and hydraulic outputs over 2 MW per unit (van Rijswick et al., 2010)."

Jan 9, 2017

By Rushikesh Battulwar, Javad Sattarvand, Joseph Seamons, Masoud Zare

In the last decade, new developments took place in the area of indoor positioning (or localization). Since the Global Navigation Satellite System (GNSS) cannot be used in underground mines, other technologies are needed for localization. Positioning and communication options today primarily include Wi-Fi, Bluetooth Low Energy (BLE), Ultra-Wideband (UWB), Radio Frequency Identification Device (RFID), etc. Smartphones and tablets currently have an array of sensors and radios, which can provide valuable information to allow indoor localization via various methods. Where mineworkers could keep smartphones with them, they can be highly effective at enabling localization and navigation. Recent applications of these technologies in underground mines have been thoroughly reviewed and examined for the likelihood of their utility for accurate localization where no other means exist. Some critical challenges and gaps that need to be addressed in future research have been identified.

Sep 5, 2021

By A. Adu-Acheampong

Photogrammetry and laser scanning has been employed at a number of Newmont mine sites to mitigate risks associated with conventional structural mapping, determining the geometry of voids from old underground workings, and generating topography in areas of slope instability. Laser scanning has also been used to evaluate as-built pit slope configurations with respect to design assumptions, operational practices, and rock fall potential. Recently, remote sensing applications carried on an unmanned aerial vehicle (UAV) were used to generate base topography at some Newmont sites. UAV are generally more convenient and less expensive and can be utilized in areas where cloud cover prevents manned aerial photography missions. This paper discusses these applications, and provides commentary on their benefits and limitations based on recent experience.

Feb 27, 2013

By B. Seegmiller, W. A. Hustrulid, O. Stephansson

Introduction The concept of in-the-wall haulage was formally introduced to the mining community in the early 1970s. The basic concept is simple. Rather than the traditional in-the-pit haulage/access ramp, single or twin ramps driven in the pit wall are used with crosscut connections on the working levels. The in-the-wall pit haulage system could be considered as part of the opening of a new mine, a way of completing to final depth an existing pit, or part of the transition from open-pit to underground mining with the ramp remaining as part of the access. This paper is intended to acquaint the reader, particularly mine planning engineers, with some of the possibilities presented by the concept. Nordstrom (1983) said, "In many countries, mining engineers are either open-pit or underground specialists and, hence, often don't consider the possibilities for combining the best aspects of each into a hybrid mining system." This is believed to be true. There are few "hybrid mines" employing, for example, open-pit methods with underground haulage systems. One reason is the variance with the experience of the mining company and the engineers involved. However, with today's low metal prices, innovative and unconventional thinking may be just what a property requires to remain in production. All the possible situations where an in-the-wall ramp might be considered cannot be presented here. Rather, a few examples will be discussed for illustration purposes. Potential savings in stripping costs A major cost in open-pit mining is associated with the removal of overburden and waste rock. Although much of this stripping cannot be avoided, the volume (V) associated with the presence of an in-pit haul road can be quite large, V 100 (pit depth) a (road width) 2 x road grade (%) As an example, consider a vertical ore body 400 m (1312 ft) long, 60 m (197 ft) thick, extending to a depth of 160 m (525 ft). Cross sections are shown in Fig. 1. Other data are: ore tonnage = 11 Mt (12 million st), ore density = 2.9 t/m3 (0.09 st per cu ft), waste rock density = 2.7 t/m3 (0.08 st per cu ft), road width = 20 m (66 ft), road gradient = 10%, and level interval = 10 m (33 ft). The evaluation has been made assuming that the pit slope (0) is constant around the pit except on the side with the haul road. On this side, the slope is decreased to allow for the road. Slope angles of 30° to 60° have been selected to indicate the dependence of stripping volume (V) on slope angle. The stripping at the ends have been calculated assuming representation by cones. The volume associated with the haul road is 2.6 Mm3 (92.8 million cu ft). A comparison of the strip volumes involved is shown in Table 1. As can be seen, the percent savings in strip volume varies from about 4% to 17% and depends greatly on the slope angle. It is perhaps more interesting to examine the savings in stripping costs that could then be used to cover the cost of the access ramp and the crosscuts for stripping costs of $3/m3 ($0.08 per cu ft). The cost with the road volume is 2.6 million x 3 = $7.8 million.

Jan 1, 1988

By Evan J. Owen, Virginia T. McLemore

The Zuni Mountains, located in Cibola County, New Mexico is an uplifted area that exposes Proterozoic igneous and metamorphic rocks overlain by Permian and younger sediments. Sedimentary-hosted Cu deposits and fluorite veins in the district have recorded production, but other deposits exist. Proterozoic ultramafic rocks may host Ni and PGE. A recent regional stream sediment survey collected 76 samples as part of an exploration geochemistry course at New Mexico Tech with the goal of assessing the critical minerals potential of the district. Whole rock and trace element chemistry of the sediment samples (<2 mm) show a variety of critical minerals possibly worthy of future targeted exploration including up to 700 ppm As, 2100 ppm Ba, 26 ppm Bi, 25 ppm Co, 640 ppm Cu, 145 ppm Ni, 110 ppm Sb, 170 ppm V, and 500 ppm Zr. Positive correlation between Bi, As, Cu, and Sb suggest that these critical minerals are found together within copper veins related to shear zones in the district. Samples collected from streams that drained outcrop of mafic and ultramafic rocks were found to generally contain more Ni, Co, and V. Samples elevated in Ni will be reanalyzed for PGE.

Feb 1, 2025

By B. Yarar

The critical surface tension of wetting (?c) of Cu2S, FeS2, PbS, and MoS2 were determined by plotting flotation recovery versus YLV which was arranged by methanol, and Extra-polating to % R = 0. ?c values ranged from 26 dyne cm-1 for MoS2 to 49 dyne cm-1 for PbS and elemental sulfur gave a value of 31.5 dyne cm-1. Minerals exhibiting natural flotability of different extents, could be separated from their mixtures in the absence of conventional flotation reagents, but controlled ?LV. Correlations between non-stoichiometry and degree of natural hydrophobicity for MOS2 are also reported in this paper.

Jan 1, 1983

By Steve Kral

The Clinton administration’s policies toward the environment have the mining industry on the defensive. The president and US Secretary of the Interior Bruce Babbitt continue to bypass Congress in their efforts leave an environmental legacy when they leave office in a year. So the mining industry must take its case to the public. And the public seems willing to listen if the industry is willing to tell its story, according to US Rep. Chris Cannon (R-UT). Cannon was one of the keynote speakers at the105th meeting of the Northwest Mining Association, in Spokane, WA. The conference, held in early December, attracted about 2,400 people and more than 200 exhibitors

Jan 1, 2000

By Hengwei Yan, Zhanwei Liu, Wenhui Ma, Ping Xiong

The sulfur in high-sulfur bauxite not only pollutes the environment but also harms alumina production. This study investigated the removal of sulfur from high-sulfur bauxite by adding Zn or ZnO during the Bayer process. The results showed that the different valence sulfur (S2−, S2O3 2−, SO3 2−, and SO4 2−) in sodium aluminate solution can be effectively removed by adding Zn during the digestion process. Adding ZnO removes the S2− in liquor, but the other sulfur compounds (S2O3 2−, SO3 2−, and SO4 2−) are not affected. The mechanism of sulfur removal has been elucidated, where the S2O3 2−, SO3 2−, and SO4 2− are first reduced to S2−, and after adding Zn, the S2− enters into red mud in the form of ZnS. The ZnO then reacts with S2− to generate the ZnS that enters into red mud. Thus, this is a new and effective method of sulfur removal by adding Zn during the digestion process. The results shed light on the removal of sulfur from high-sulfur bauxite during alumina production.

Jun 24, 2020

By Francesco Chiappalone, Filippo Azzarà, Raffaele Aliberti, Daniele Nebbia, Lance Waddell

As part of the 3RPORT and NEBT Projects, 5-mile Combined Sewer Overflow Tunnels were excavated with a 19 ft diameter Slurry and 26 ft diameter EPB Tunnel Boring Machines. Due to the difficult geological and hydrogeological conditions, both tunnels were excavated maintaining a ground support pressure between 2 and 5.5 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of both projects while the second part focuses on the challenges and technical details of the pressurized breakthroughs that took place in deep shafts excavated in urban environment as part of the projects.

Dec 1, 2022

By John E. Shively, Tracy K. Lundin, Francis Fong

The Superconducting Super Collider (SSC) features two 20 TeV counter rotating proton beams which will be housed in 87 km (54 miles) of tunnel. Four additional lower energy particle accelerators will be housed in 26 km (16 miles) of tunnel and underground structures. Physics experiments will be conducted in two underground detector halls approximately 67 m (220 feet) deep with footprints measuring about 30 m (100 feet) by 100 m (330 feet). Definition and design of underground facilities is advanced with construction of approximately one-third of the SSC program underway. This paper presents an overview and status of the SSC project.

Jan 1, 1993

By Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths (from 500 feet to 1000 feet) and six different diameters (from 14 feet to 24 feet) were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1977

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By A. L. Anderson, J. T. Rybock

Lime, soda ash and similar precipitants have been the industry standard for treatment of acid rock drainage (ARD) because of their proven ability and low per-gallon operational cost. However, these methods carry serious environmental drawbacks and high life-cycle costs. KEECO’s Silica Micro Encapsulation (SME) technology has all the positive characteristics of conventional ARD-treatment systems but none of the drawbacks. SME achieves highly effective treatment in a single step, provides options for ARD prevention and recovery of metals, requires lower capital expenditures, generates smaller volumes of higher-density sludge, consistently passes leach tests, and eliminates long-term liabilities associated with potential metal remobilization and hazardous waste landfilling.

Jan 1, 2000

By J. C. Stankus, K. J. Ma, D. Faulkner

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding-type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high, causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concern for the U.S. Mine Safety and Health Administration (MSHA) and ground control engineers. During the last few years, Keystone Mining Services, LLC developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents an impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development and laboratory testing of a waterproof coated impact-resistant lagging panel and (3) impactresistant steel set design based on the law of conservation of energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Jr. Matthews

The Candelaria copper-gold deposit is located in Region m of Chile, 805 kilometers north of the capital, Santiago. Candelaria was discovered in 1987, following a six month exploration program. In late 1986, induced polarization (IP) surveys outlined an anomalously high response within the area of interest. The first test hole bad three intersections totaling 49 meters, with an average grade of 1.97% copper. Drilling eventually outlined approximately 390 million tonnes, grading 1.09010 copper and 0.26 grams/tonne gold. Production began in early 1995 and is estimated at 120,000 tonnes copper and 80,000 ounces gold annually.

Jan 1, 1996

By Josh B. Taggart

Some twenty to twenty-five years ago we saw the beginning of mechanization in our coal mines, It has now progressed to the point Chat as instruments of production the pick and shovel are things of the past, They had to give way to better and more efficient methods--so mechanization, followed by and combined with automation, has become common-place in our mines. Our coal could not keep its competitive position without this progress Without it our industry could not look to the future with any degress of confidence. Today we lock back and see cases of regained and salvaged markets. We see better coal products being produced at decreasing costs. We see better utilization of manpower and a stronger, more confident industry, Our hats arc off to those mining men, equipment manufacturers, labor leaders, and others who had the foresight to work toward these ends and the ability to bring them about.

Jan 1, 1962

By James J. Anthony

High-angle in-pit conveying is an idea that is being seriously studied by a number of important mining companies in North America. Its application in coal, iron ore, and copper mining is expected to reduce mine operating costs considerably compared with the conventional discontinuous methods, such as truck haulage, which are fuel, labor, and maintenance intensive. Therefore, a mine introducing high-angle in-pit conveyors will gain a competitive advantage over mines which continue to use conventional haulage. While the capital outlay for in-pit conveyor systems obviously varies depending on pit depth, the angle of incline, and the capacity required, it generally will not exceed that of truck haulage when all Factors are taken into consideration. These factors include the cost of excavation, as measured in relation to the volume of minerals mined, the cost of building truck ramps and roads, and the capital outlay for the trucks and maintenance facilities. In many cases, in Fact, the capital outlay will be less than for truck haulage. This cost advantage will best be realized by new mines, whereas in existing producing mines the switch from truck haulage may involve the abandonment of a substantial capital asset.

Jan 1, 1983

By J. H. Kempton

Refinement of environmental procedures can produce significant cost savings at most mines. Grouting permeable aquifers reduces water pumping and disposal costs. Stable groundwater quality supports reduced groundwater monitoring; and for contaminated groundwater, in-situ or natural restoration should be evaluated. Waste-rock characterization can be minimized using fewer (but more representative) samples, inexpensive surrogate analyses (e.g., NAG instead of humidity cells), and appropriate tests (e.g., avoid meteoric tests on sulfide). Selective waste-rock handling should be compared to random emplacement, which is often cheaper and more stable. Finally, incorporating schedule uncertainty in modeling allows the flexibility to revise mine plans within permits.

Jan 1, 2000

By R. S. Jurani

Sunshine Mining Co.&apos;s Kellogg operation is the primary silver producer in the US. Maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and un-certain silver markets, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a two-year, $400,000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants. This saved the company about $650,000 per year.

Jan 1, 1988

By S. Mischler, J. Noll, G. Schnakenberg, A. Bugarski, M. Crum

Diesel particulate filter (DPF) systems and biodiesel fuels are two of the most promising technologies available to the mining industry to reduce the exposure of underground miners to diesel particulate matter (DPM). A study has been conducted to estimate the potential of DPF systems and biodiesel blends to reduce DPM emissions from production vehicles. Results of testing three DPF systems in an isolated zone showed 88% to 99% reductions in elemental carbon concentrations. The test results also show that biodiesel blends, B20 and B50, reduced the elemental carbon concentrations in the mine air by 26 and 48 percent, respectively.

Jan 1, 2004