Search Documents

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R and TGA testing setups in our ventilation laboratory, samples from US coal mines have been collected and tested. 70 The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal which is a good indicator for potential of self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential of coal self-ignition. The trend of activation energies determined using TGA techniques and adiabatic tests are reasonably consistent with each other. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal are easier to be activated with a small amount of activation energy at a relatively low temperature, the coal will has a higher potential of self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with low potential of self-ignition has low self-heating rate, high activation energy and high minimum self-heating temperature.

Jan 1, 2012

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

By E. Bakhtavar

Finding a ?practical spacing between the holes? for use of the expansive mortars is an important problem in dimension stone quarries. Objective has been to first introduce a relationship between this spacing and the dependent parameters in such a way that the required size and shape of the blocks is produced with the maximum efficiency and safety, minimum wastage, conservation of reserves and protection of environment. For this purpose, a dimensional analysis was used. On the basis of granite and marble rock types in Iran two separate relations are hence established to calculate the practical spacing between the holes.

Jan 1, 2011

By Roger Best

In the mining industry, where some of the vehicles are larger than a one-story house, tire maintenance cannot be accomplished by the tire shop alone. It takes an army of people to maintain a fleet of 100 trucks that may be transporting gold, iron ore, oil sand, copper or coal from an openpit to a refinery and eventually delivering the product to a customer. Everyone working in and around these mammoth machines has a duty to help with the maintenance of the tires, whether they know it or not. These responsibilities comprise observation and reporting hazards up to and including changing out a tire and recording the information in a tire-tracking program such as TreadStat.

Jan 2, 2010

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameters like commodity price, mining or processing cost, stripping ratio etc. The most important characterization of these push backs is that the inner most push back has the highest value per ton, the second inner most push back has the second highest value per ton and so on. These nested pits are generated based on the best estimates of grade within a representation of the ore body in a three dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduced a new algorithm that incorporates ore grade uncertainty during push back design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence.

Jan 1, 2007

By R. P. Gardner

Results of work on the development of a phenomenological model for the continuous flotation process using short-lived radioactive tracer techniques for the determination of model parameters is reported. A model that incorporates a flotation first-order rate constant and a residence time distribution based on the cross flow finite state (CFFS) model has been derived and investigated. The short-lived radioactive tracer techniques necessary to extract the model parameters have been developed as have the necessary nonlinear search methods. The conditions under which all the model parameters can be extracted from a single radiotracer experiment are detailed and illustrated. A microcomputer-based unique data logging system has been designed, assembled, and implemented for collecting the necessary transient radiotracer data. Results are reported for a continuous laboratory flotation system for the two systems mica ore and coal.

Jan 1, 1985

By Alexander Karim

This paper reviews the growth pattern in bauxite and alumina production, and primary aluminum smelting through 1980. Because the alumina and primary metal are intermediate products of the major integrated aluminum companies, it is not possible to determine their production costs. The costs indicated in this paper are order of magnitude costs based on published figures and the market price of these products. The conclusions in this paper indicate the general pattern of growth in the aluminum industry and are not meant to be a substitute for the feasibility and economic studies that are needed for individual bauxite mining, alumina refining and aluminum smelting projects.

Jan 1, 1968

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By Z. H. Zhou

It is difficult to remove cadmium from raw indium using only electrolytic refining because their standard potentials are similar. In this paper, physical and chemical methods were used to remove Cd from raw indium. Indium metal is vacuum refined for two hours at 400°C with a vacuum pressure of 20 Pa. In this process, 99.70% of the Cd can be removed. The removal rate of Cd reaches 90% to 95% when indium is further smelted for 10 minutes in a 20% glycerin solution of KI and I2 at 180°C. When pre-indium is electrolytic refined in an In2(SO4)3-H2SO4 system, in which the indium content is 80 to 100 g/L, the pH is 2.0-3.0 and the current density is 80 to 100 A/m2, the contents of the impurities decrease and the purity of the indium product reaches 99.99%.

Jan 1, 2007

By Michael S. Zhdanov

One of the major problems of mineral exploration is the ability to reliably distinguish between uneconomic mineral deposits and economic mineralization. While the mining industry uses many geophysical methods to locate the mineral deposits, until recently, there was no reliable technology for mineral resources identification and characterization. The main goal of this project is to develop a new geophysical technique for subsurface material characterization, mineral exploration and mineral discrimination, based on electromagnetic methods. The proposed new technique is based on examining the spectral induced polarization effects in electromagnetic data using the modern distributed acquisition systems and advanced methods of 3-D modeling and inversion. The recovered parameters of the relaxation model will be used for the discrimination of different rocks, and in this way will provide an ability to distinguish between uneconomic mineral deposits and zones of economic mineralization using geophysical remote sensing technology (Zonge, 1976). The proposed research and development is undertaken using multi-partner collaboration between the University of Utah, four major mining companies, Kennecott Exploration, BHP Billiton World Exploration Inc., Placer Dome Inc., Phelps Dodge Exploration, and Zonge Engineering Inc., which is equipment manufacturer and service provider to the mining industry. The multi-partner collaboration between the academic institution, the University of Utah, and mining industry helps to identify the appropriate mining target and conduct the field experiment for practical demonstration of the developed new technology, which is an important part of the this project.

Jan 1, 2005

By C. C. Hamilton, G. R. Lane

Traditionally, mineral sands are evaluated by preparing several mineral products using a combination of heavy liquid-, magnetic-, and electrostatic methods. Whole-rock assays (WRA) are then conducted on ilmenite, rutile and zircon products in order to determine trace element contents, which may affect project feasibility. Combined methods can be time consuming, expensive and even outdated due to the use of banned and toxic chemicals such as clerici solution. Coupled with large field-sample quantities, these procedures can potentially introduce unacceptable sampling and related errors. Modern mineralogical analysis techniques can provide complete mineralogical inventories on a single THM product, reducing the amount of processing involved in satisfactory characterization of early exploration samples. A small exploration sample can be processed to produce a small THM concentrate using readily available gravity/density methods. In turn, the THM product is submitted for Whole Rock Analysis (WRA) and mineralogical inspection by X-ray diffraction (XRD), and microscopic evaluation. Modal mineralogy and textural data can be determined using optical methods, automated image analysis, and scanning electron microscope (SEM) based systems. Benefits of automation are reproducibility and the capability of rapidly analysing thousands of particles as opposed to manual optical methods. Automated systems include the use of Automated Digital Image Analysis (ADIS), and SEM-based systems such as the Mineral Liberation Analyser (MLA) and QemSCAN. For detailed mineral chemistry, microanalysis techniques ranging from electron microprobe (EMPA) to Secondary Ion Mass Spectrometry and Laser Ablation Mass-Induced Coupled Plasma-Mass Spectrometry (LAM-ICP-MS) are used. Examples of these automated and analytical methods are presented. ADIS at SGS-Lakefield Research uses optical characteristics to identify and measure mineral species in THM samples; rutile, pseudorutile, ilmenite and leucoxene can be distinguished. Analysis of a single THM product provides bulk modal mineralogy and grain size distribution of particles and the individual mineral grains. Textural information is also obtained detailing mineral associations as well as degree of alteration. Where textural and chemical resolution renders mineral identification ambiguous, SEM-based methods offer better resolution. Examples of this ambiguity are shown in this paper, which leads to QemSCAN as the preferred method where within-grain variability is concerned. Sampling and measurement strategies are followed to meet study objectives, providing a value-added framework for a sequential, cost-effective strategy, which will meet due diligence and bankable accreditation criteria. Studying a THM product by electron microprobe and LAMICP-MS may reveal potential fatal flaws related to mineral chemistry. Low detection limits in the range of 200 to 500ppm are possible using electron microprobe analysis for suitable matrixes (U, Th in zircon). For the detection of ultra low level elemental contaminants, LAM ICPMS is the most accurate method of evaluation. Elements including U, Th, La, Ce, Nb, and V in Ti-minerals can be determined down to 50 ppm.

Jan 1, 2005

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By I. J. Duckworth

Due to improved, stringent safety regulations, many modern road tunnels are statistically safer, per kilometer, than above ground roadways. However, the public perception and reaction in the event of a serious tunnel fire is very different to that associated with a surface incident. Vehicle fires in road and rail tunnels are recognized to represent an immediate and extreme danger to the patrons of those systems. Unlike workers in the mining and civil construction industries, the general public are neither trained nor equipped to fight fires or evacuate under deteriorating smoke conditions. Accordingly, for the majority of modern transportation tunnels the ventilation infrastructure is sized on the requirement to control the combustion products from worst-case fire scenarios and to provide a tenable evacuation route for the tunnel users. It is common for these same emergency ventilation systems to be employed, often in a reduced capacity, for other operating modes such as the dilution of pollutants during congested traffic conditions. This is one of the fundamental differences to mine ventilation, where primary ventilation systems are not typically sized based on fire scenarios. This paper presents an overview of the subject of fires in vehicular tunnels. This includes a brief history of major transportation tunnel fires followed by a discussion on the resulting legislation and standards that govern the design and operation of tunnel emergency ventilation systems. A summary is provided on the common criteria, theory, and design techniques that are employed during tunnel emergency ventilation systems design. Information is provided on fire detection and suppression, with a discussion on the growing acceptance of wet suppression as a means to mitigate major fires in road tunnels worldwide.

Jan 1, 2009

By G. Kim

The influence of bacterial growth phase on the flotation behavior of malachite has been investigated in a well-controlled Hallimond tube system. The microflotation tests were conducted for malachite (45?53 µm) using different amounts (bulk phase concentration=1×108?5×109 cells/mL) of Rhodococcus opacus (R. opacus) as a collector, which was grown at mid-exponential versus stationary phase, at a constant speed (340 rpm), pH (6), and malachite-bacteria interaction and flotation time (each 10 min). Hug differences between R. opacus cells in mid-exponential and stationary phase was observed from the results for electrophoretic mobility and flotation tests. Specifically, the isoelectric point of the cells in the stationary phase was lower than that in the mid-exponential phase, suggesting that the amount and distribution of surface functional groups onto cell surfaces are likely different. Additionally, the cells in stationary phase led to significant increase in the flotability compared to those in mid-exponential phase over the background bacterial concentration level of 1×108?5×109 cells/mL. Furthermore, the flotation efficiency tended to increase with increasing cell dosage for stationary phase cells while no distinct difference was observed for mid-exponential cells.

Feb 27, 2013

By Steve Kral

Led by a surge in coal production and prices in recent years, Colorado’s mining industry is taking part in the same revival as others states and the world. Not too many years ago, the state’s industry was languishing in the same doldrums as the rest of the mining world. Ironic for a state whose history was based on mining. Now, however, Colorado’s mining can boast increased production in all commodities produced, along with prices that allowed companies to expand, increase work forces and post improved shareholder value. So there was a lot of optimism at the Colorado Mining Association’s (CMA) 107th National Western Mining Conference in February. The conference, held in Denver, attracted more than 500 attendees and 39 exhibitors. The theme was Colorado Mines the World.

Jan 1, 2005

By N. Aouad

The deployment of large machinery for low cost, bulk surface mine production operations has resulted in high-impact shovel loading operations (HISLO). In extreme cases, shovels load large dump trucks with 100-ton (or more) passes generating high-impact forces under gravity. HISLO generates high-frequency shockwaves that cause severe truck vibrations exposing operators to whole body vibrations (WBV). Current research study in this area has established that the vibration levels affecting the operator?s seat, lower-back, lumbar and cervical regions fall within the extremely uncomfortable zone compared to the ISO 2631 comfort zone. These results pose health threats to truck operators over long-term exposure to these vibrations. In this paper, the authors will examine engineered solutions to mitigate these health threats.

Jan 1, 2011

By J. Piper

Markets and Production Beryllium (Be), an extremely light metal, is used in many specialty applications. It the lightest element in Group 2A of the periodic table, with a specific gravity of 1.85 gm/cc, and a high melting point of 12850C (Calvert, 2004). The functional properties of beryllium are stiffness, strength, dimensional stability, resistance to corrosion from acids, and electrical and thermal conductivity. The ability to reflect neutrons and transmit x-rays, makes beryllium irreplaceable in uses such as precision optical components, inertial guidance systems, and in nuclear reactors (Anon, 1993). Beryllium is used in Cu alloys to strengthen and reduce corrosion in copper wire, and in lightweight oxide ceramics that are used as heat sinks, and as electrical insulators. The market revenue of beryllium can be broken down into the seven major groups below, and are plotted on the pie chart in Figure 1 (Anon, 2005). 1.) Telecommunications & Computer 2.) Magnetic & Optical Data Storage 3.) Aerospace and Defense 4.) Automotive Electronics 5.) Industrial Components 6.) Appliance, and 7.) Other.

Jan 1, 2007