Search Documents

By R. A. Paul

The requirements for water inflow control for the Chicago Intercepting Sewer System are stringent. This posed special problems in grouting the bored and conventionally mined tunnels, shafts and chambers of the system. In adapting conventional grouting techniques to the specific problems encountered in the system's pilot project, numerous field procedures were developed. Careful preand post-grout testing and evaluation identified the most efficient and economical of these procedures. As an example of some of the conclusions reached during the project it was found that the mineralized groundwater in the Chicago area tended to reduce the efficiency of the grout holes, thus limiting their useful life. Pressure washing to remove natural fillings was a critical factor in achieving a permanent grout seal. The value of relatively thin lubricating grout mixes was definitely established. Although not an ideal situation, satisfactory results could be obtained by manifold grouting several grout holes simultaneously if done within specific limits of hole groutability, location and numbers. Caulking proved to be a primary controlling factor in achieving acceptable results. To achieve such a high degree of water inflow control requires close supervision by experienced personnel. "Temporary grouting as a construction expedient" produces seepage conditions which are extremely difficult to treat.

Jan 1, 1974

By Tony Weeks, J. Loah, Ian Mcgaffin

PT Newmont Minahasa Raya (PT NMR) operates a 700,000 tonne per annum open cut gold mine in the Minahasa region of North Sulawesi. The operation commenced production in the second quaiter of 1996 and is expected to produce an average of 150 000 to 180 000 ounces of gold per year for the mine life. The deposit is predominately refractory in nature and requires a complex treatment route incorporating dry milling and whole ore roasting followed by conventional cyanidation and adsorp­tion of the gold onto activated carbon. Gold is eluted from the carbon to produce <lore bars assaying approximately 94 percent gold. A scrubbing system for the removal of mercury from the roaster off gases was commissioned in late 1997. Due to the location of the operation, close to the coast and in seismic region with high rainfall submarine tailings placement (STP) was the preferred method of tailings disposal. Prior to dis­posal into the ocean the tailings from the CIP plant are detoxified in a three stage detoxification circuit to treat cyanide, arsenic and mercury. This paper reviews some of the design and operational fea­tures of the whole ore treatment process employed at the Minahasa Gold Mine.

Jan 1, 1998

By D. Legg

This is the first in a series of studies commissioned by the European Environment Agency that aim to raise awareness of the use of economic instruments and assess their effectiveness. The emphasis is on sharing good practice and increasing knowledge and understanding across European countries in this emerging policy area. A methodology for evaluating the effectiveness of economic instruments has been developed and this will examine whether the inclusion of economic instruments in complex policy packages can improve the overall performance, particularly as a prevention tool in terms of resource use and waste generation The focus for this initial study is the use of aggregate taxes in four EU countries which include the Czech Republic, Italy, Sweden and the UK so that a range of experiences (e.g. geographical, political etc.) can be included. The findings will be used to inform and influence future policy development in other EEA countries. The methodological approach is divided into two main sections: - Technical analysis, which covers quantitative and qualitative analysis. - Process design, i.e. who should be involved when, where and how. Process design is essential if the full learning benefits are to be gained from the technical analysis, which is the ultimate objective of these evaluations.

Jan 1, 2007

By R. F. Kovar, R. N. Torbin, R. E. Gundersen

I have to express my .surprise and must send a note of warning concerning the use of polyurethane foam as described in a paper by R.N. Torbin and R.F. Kovar, entitled "Innovative Shaft Lining Method," published in your February 1989 edition. In September, 1986, 177 miners lost their lives when they were exposed to fumes downwind from a fire in a tunnel lined with polyurethane foam. Whilst polyurethane exhibits reasonable fire retardent properties in small-scale tests, mass use in a tubular configuration, exacerbated by the furnace effect of cross-radiation, can lead to a rapid, uncontrollable conflagration. I do not wish these comments to detract from the engineering achievements of the authors but rather to sound a loud warning as to the application of the system. Any shaft designed for human access- be it for transport or shaft work - and any intake airway, should not consider the use of polyurethane foam. It only needs a slip with a cutting torch or an electric fault to initiate a disaster. Many countries have banned or restricted the use of polyurethane foam in the workings of a mine and maybe alternative foams (e.g. phenolics) can be used or developed

Jan 1, 1991

By Hugh R. Wilson

Echo Bay&apos;s Waste Management Program for its Lupin Mine was developed in response to the terms and conditions of the water license issued to the mine in 1981 by the Northwest Territories Water Board. The gold mine, located about 80 km (50 miles) south of the Arctic Circle, commenced production in 1982. The Waste Management Program was based originally on the total containment concept, contingent on future treatability testwork results indicating the best treatment method to ensure pond discharges would be in compliance with stated Northwest Territories Water Board discharge criteria. To assess the various treatment technologies, an investigative program was established to determine the most effective means for treating the tailings pond water. In the course of milling, about 850,000 m3 (11 million cu yd) of tailings are produced annually that require appropriate management to protect the environment. This annual tailings stream consists of about 175,000 m3 (229,000 cu yd) of solids and 675,000 m3 (883,500 cu yd) of water. Following the completion of the required waste management studies, a two-ponds-in-series concept of tailings impoundment was developed. To attain this concept, the tailings impoundment area would require modification and construction to enable the use of such a system.

Jan 1, 1991

By D. Rajkovic

Geothermal sources are exploited in two basic forms, i.e., the primary form of thermal energy and that converted into electrical energy by using an adequate thermodynamic cycle. There is a possibility of applying several processes for the conversion of thermal into mechanical or electrical energy, which depend on the thermodynamic characteristics of the geothermal water. Geothermal sources in Croatia do not contain steam of relatively high temperature, like in Italy, although both countries are nearly in the same position with respect to geothermal belt. Geothermal sources in Croatia are mostly so-called low-temperature geothermal sources with water temperatures lower than 100°C (Cubric and Jelic, 1993). A few of them have been exploited, although the percentage of utilization of their available power is still very small. The low-temperature potential is a major disadvantage when it comes to power generation, since state-of-the-art geothermal power plants require reheated steam or hot water to operate. There is a common belief that the optimum way of exploiting low-temperature geothermal sources is heat generation. Therefore, this analysis is especially aimed at potential users and showing the technical and economical possibilities of using low-temperature sources for conversion of thermal energy into mechanical work and electrical energy.

Jan 1, 2003

By Alan L. Mierke

West Virginia&apos;s economy has been closely linked with coal. West Virginia is consistently one of the top three coal-producing states. Its 149 Mt (164 mil¬lion st) produced in 1992 represented 16.5% of total US coal production. In recent years, the state&apos;s economy has experienced a diversification away from its traditional employment base of min¬ing and heavy manufacturing. However, the coal industry remains an integral part of the lives of West Virginians. Coal is mined in 33 of the state&apos;s 55 counties. In many of these counties, the coal industry is the largest private employer and contributor to the economy. West Virginia has three major coal-producing regions. The northern region produces coal high in gas and sulfur content (steam coal). It is consumed primarily by utility and industrial markets. The southeast region produces high-grade coal low in sulfur content but high in carbons and Btu (metallurgical coal). The southwest region produces metallurgical and steam coal. The high-grade metallurgical coal is used in the production of coke for steel manufacturing. Metallurgical coal also comprises the majority of coal exported from the United States. During 1993, West Virginia was the country&apos;s largest exporter of coal, accounting for 44.5% of total US coal exports.

Jan 1, 1995

By J. Craig Green

Companies mining for coal, oil shale, and minerals in the western US must often complete extensive geotechnical studies to satisfy federal and state regulations. The modern mining process is further complicated by the legal problems and liabilities associated with mineral rights and land leasing. Yet the study of water rights-unique to the West is often incomplete or ignored until the latter stages of mine planning. Water rights in the West are not adequately understood by many mining companies and their geotechnical consultants. Some firms, headquartered outside the western US, have not had to contend with the water supply problems of a semi-arid region. Water problems encountered by eastern mining companies, for example, are primarily water quality, drainage, and flood control. Even when water quantity is a problem in these areas, ownership and/or use of it is governed by entirely different legal and administrative concepts than in the West. Both legal and engineering issues have to be considered when studying western water rights. Legal issues, such as existence and title, must be addressed to insure that a particular water right is properly established and maintained. The exercise of a water right, however, often requires engineering analyses that focus on preventing injury to the properly established water rights of others.

Jan 8, 1981

By Frank E. Dalton, Forrest C. Neil

INTRODUCTION The Tunnel and Reservoir Plan (TARP) (Figure 1) was adopted in 1972 as the most cost-effective way to bring Chicago area waterways up to Federal and State water quality standards. TARP will significantly reduce pollution of these waterways and provide flood relief for Chicago and 53 adjacent suburban communities. These communities, covering an area of 971 sq km (375 sq miles), are at present served by combined sewers, which carry both raw sewage and stormwater. Because porous ground surfaces have been covered over in recent years by buildings, streets, and parking lots, stormwater runoff into sewers frequently exceeds the capacity of the sewers. When this happens, sewers back-up into hundreds of thousands of basements, and the overflows on the combined sewers discharge rainwater mixed with raw sewage directly into the area&apos;s waterways at 645 overflow points. The result is severe pollution of the waterways and flooding in 53 communities. During particularly heavy rains, overloaded rivers have to be relieved by opening the locks and allowing the polluted waterways to flow into Lake Michigan, the region&apos;s water source. Goals of TARP 1. PREVENT BACKFLOWS INTO LAKE MICHIGAN. 2. ELIMINATE WATERWAY POLLUTION CAUSED BY COMBINED SEWER OVERFLOWS. 3. PROVIDE AN OUTLET FOR FLOOD WATERS.

Jan 1, 1981

By E. B. Kroeger

One of the problems encountered when constructing a roadway is the planned route often needs to cross soils that are soft and highly compressible. An approach to dealing with soft and compressible soils is to construct the fill from lightweight materials, thereby reducing the stresses on underlying soils. Most lightweight fills have approximately the same cost, so the most important consideration when choosing a lightweight fill is that the material properties of the lightweight fill match the conditions existing at the site. Expanded polystyrene (EPS) has been used as a lightweight fill material for more than 30 years. The EPS used for road fills is typically in the range of 0.5 to 2 lb/ft3, and has a compressive strength of in the range of 10 to 30 lb/in2. If a higher strength material is needed, then the material density is increased, which also adds to the cost of the material. Another type of lightweight fill material that is commonly being used is lightweight aggregate (LWA). LWA can be created by passing slate or shale through a rotary kiln or reheating coal fly ash with other materials to form pellets or aggregate. Several companies throughout the U.S market these materials under a variety of names. LWA can have a unit weight from 45-80 lb/ft3. For sites where trucking granular fill does not pose a problem, this material may be an alternative to EPS. One of the drawbacks to using LWA is the availability of the material. Only a few companies are manufacturing LWA, so it may not be available or may be cost prohibitive in certain areas of the country. Lightweight flyash blocks have been produced which may fill the gap in unit weight between the EPS and LWA. Blocks have been produced with a unit weight as low as 30 lb/ft3. They are relatively inexpensive, easy to handle, and have a moderate compressive strength. Although the unit weight is dramatically higher than EPS, the strength is also higher. If lateral stabilization of the fill is a problem, then geofabrics or grids can be incorporated into the design to add lateral strength.

Jan 1, 2003

By A. Athousaki

The Ecological Footprint is a resource accounting tool used to address underlying sustainability questions. Aggregates consist of natural, artificial or recycled materials. The production of aggregates is the fastest growing activity worldwide since huge quantities are required by the construction industry. This paper presents a parametric investigation of the ecological footprint of transporting aggregates for urban use as a function of tonnage and distance.

Jan 1, 2008

By Priscilla P. Nelson, Steven D. Glaser, Thomas D. Rourke, O&apos

Construction records from six projects which employed full-face TBMs to drive 18 km of tunnel in sedimentary rock have been analyzed. More than twenty individual causes of delay could be identified. Delay causes are characterized on the basis of frequency and duration of incidents. Average utilization and downtime distributions are presented for each project, and frequency distributions of downtime per shift are discussed.

Jan 1, 1985

By John A. Kaufman, Terry D. Vandell

Recent mining regulations have increased the need for detailed engineering and environmental information pertaining to the hydrogeologic environment in mining areas. The cost of obtaining such hydrogeologic information has also increased. After mineralization of potentially economic grade ore and tonnage has been identified, and after completing preliminary mining feasibility studies (suggesting that development is merited), a second exploration phase can incorporate a simple, cost-effective baseline hydrogeologic data reconnaissance program that is limited but useful. Using exploration drill holes only, this program can provide a direct indication of where ground water is encountered. Also, reasonable estimates can be made on the relative production of water from various water-bearing strata, a composite potentiometric surface map can be prepared, and the general chemistry of the ground water can be characterized. This article outlines what typical baseline hydrogeologic data are needed and describes how it can be easily obtained during exploration drilling. Introduction Major engineering and environmental ground water parameters can be identified early in a project by using, drill hole data obtained from a mineral exploration program, designed by the mine geologist and hydrogeologist. Most importantly, data obtained in the exploration drilling program can be used to design a logical, defensible, and cost-effective baseline ground water data reconnaissance and monitor well program, which would be required for mine design and ultimately for mine permit approval. Drilling Where possible, exploration drill holes should be drilled with conventional rotary drilling equipment using air or, if necessary, water as the drilling fluid. Rotary air or water drilling generally allow good delineation of the first major saturated or water-bearing zone. If mud must be used during drilling, distinct hydrogeologic zones can still be defined, although the task may be considerably more difficult. Water Levels Static water levels can be obtained from selected exploration drill holes at specific depths while additional boreholes are drilled. Such measurements should not, however, be conducted until the hole has been developed with air (no water) and has stabilized at each of the depths to be measured. Such water-level information can be particularly useful when more than one aquifer exists. Where mine development is eminent, the hydrogeologist should install 50-100 mm (2-4 in.) diameter PVC casing in select drill holes. The PVC should be slotted, gravel packed, and properly sealed so additional hydrogeologic data can be collected for specific hydrogeologic zones at a later date. Such data could include water level information, permeability estimates based on injection and /or pumping tests, and water quality data. Where casing is not installed in drill holes, or when the drill holes are abandoned, the holes should be properly grouted and back-filled to the ground surface to prevent potential future ground water contamination. Monitoring Air Lift Water Production Estimates of the relative production from various water-bearing strata can be obtained from selected exploration drill holes. If ground water is encountered, its air lift (ground water flow) production can be measured at distinct intervals using a surface water flow measuring device, such as a portable Parshall

Jan 2, 1983

By Arnold Griffin

Numerous articles have been published describing the procedures and solvents used for the recovery of gold from ores and industrial products. I consider that the most innovative gold solvent is weak cyanide solution as described in the McArthur-Forrest patents issued in 1887 and 1889. This fundamental process is still applied in spite of the efforts of numerous researchers to develop more effective and economic alternative solvent.

Jan 1, 1998

By A. Bruynesteyn

Most ores and coals contain sulphide minerals such as pyrite, FeS2, the sulphur portion of which is a ready substrate for a variety of sulphur oxidizing bacteria. Although there are several bacteria capable of oxidizing sulphide minerals, the most often discussed culprit is Thiobacillus ferrooxidans.. Oxygen from the air slowly oxidizes pyrite into sulphuric acid, but T- ferrooxidans can increase this reaction rate several 100,000 times.

Jan 1, 1991

By Antonio Jorge de Sousa

In order to compare several mining variants, on the point of view of the variability of the ore quality parameters, a conditional simulation technique is applied to a complex pyrite deposit (FEITAIS orebody, Portugal). Exploitation methods such as cut and fill and sublevel stoping are studied by the a.m. methodology. For each mining variant, it is assessed the influence of several mining operators on the variability of grades.

Jan 1, 1982

By S. Dinescu

The paper deals with the modeling of longwall shearer cutterhead interaction with the coal, in order to study the influence of different limiting factors of the haulage speed, and the cutting regime ensuring optimal energy consumption A computer simulation model is used to draw-up the torque vs haulage speed and the haulage force vs haulage speed dependence diagrams, for different strength of coal and different degrees of bit wear.

Jan 1, 2008

By Dennis A. Giardino, Leonard C. Marraccini

This paper surveys noise levels, noise exposure patterns, and frequency spectra found in the mining environment; the effects of mining noise on the working population; and the quantification of hearing loss in the coal mining industry. Federal mining noise regulations and the present state of the industry, with respect to noise control technology, are discussed. Examples of proven noise controls for mining are included along with measured noise reductions.

Jan 1, 1986

By Heinz Hofmann

In order to drive tunnels with low overburden in town regions, it is necessary to give a quantitative prognosis for the deformation of the underground as well as of the tunnel-lining and of its stability. These problems and their solutions are illustrated by the works for a two-track-railway-tunnel in Bochum (Ruhrdistrict). In this case the most important problems consisted in passing below buildings in a vertical distance to the fundamentals of only 3.20 m and a railway earthdam with rapid train traffic in a distance of 4 m under the dam. The results of measurements from other comparable tunnels and finite-element-computations were used to prognose the settlements on the surface and in the ground, their distributions and their development in time. To obtain these values at the site, a special system of tunnel driving was executed. The tunnel was excavated with the newest type of tunneling-machine from DEMAG, cutting an inclined front, immediately followed by a special temporary support of shotcrete and inclined steel-ribs. By using theoretical and empirical methods to assess the behavior of the tunnel and underground and by executing an optimal driving system in technical as well as economical aspects, the expected behavior, expressed in quantitative values, was almost equivalent to those received by control measurements.

Jan 1, 1974

By Kathleen A. Altman

INTRODUCTION The basic premise of the ideas presented in this paper are as follows: Engineers believe that "theoretically" it will work. Operators ask what they must do to make it work. And, people can screw it up. r Today the challenges conf onted during the engineering, startup and operation of mines are becoming more complex. As mining and processing professionals, we are called upon to trav­el all over the world, are subjected to a wide variety of climates and must deal with a numerous cultures and people. Historically, for the majority of the people working in the mining industry, the primary challenges related to projects have focused on the differing perspectives of the disciplines involved. For example, geologists focus on resources and reserves, mining engineers relate to tons or tonnes, metallurgists count ounces or pounds or kilograms of product, mechanics emphasize availabil­ity, human resources personnel deal with absentee rates and turnover and accountants watch the bottom line ($$'s). As the world has become "smaller" and the mining industry has become more globalized, the puzzle is becoming increasingly difficult. Even the most experienced in the crowd of mining profes­sionals are oftentimes surprised by the types of problems that are encountered. Try as we may, we cannot anticipate the complex­ity of dealing with the human side of an operation.

Jan 1, 1998