Search Documents

By G. S. Grainger, R. A. Cummings, F. S. Kendorski, R. L. Butts

Georgia Power Company's Rocky Mountain Project, located approximately ten miles northwest of Rome, Georgia, in the Valley and Ridge Physiographic Province, is a pumped-storage facility rated at approximately 800 megawatts of peaking energy. Geological field explorations and borings enabled the division of the rocks along the tunnel and shaft alignment into distinct lithologic units and defined the ground--water regime. Field explorations included a detailed analysis of the rock mass discontinuities at available rock unit exposures. Testing of rock strengths was performed in several phases in both the field and the laboratory. The field testing consisted of point-load testing, geophysical testing, in situ load testing, and hydro-fracture testing. Laboratory testing determined the Brazilian split-tensile strength, the unconfined compressive strength, the triaxial compressive strength, the joint-direct shear strength, and the pulse velocity. The rock mass along the tunnel and shaft was also characterized by empirical classification systems. The classification systems included the Rock Mass Rating (B1IR) and the Rock Mass Strength Determination (RHSD). The results of the field explorations, field testing, laboratory testing, and rock classifications were used to divide the rocks into two structural groups. These rock groups were defined as volumes of rock wherein the rock mass behaves similarly in response to the excavation. Each group, therefore, required separate rock engineering consideration.

Jan 1, 1986

By Naj Aziz

Both bolt profile shape and spacing (rib spacing) have been found to influence the bonding capacity of the grouted rock bolt. The bolt surface profile configuration has greater importance to rock bolting in strata reinforcement in mining than the steel rebar used in civil engineering construction. This is because a rock bolt in mining usually is subjected to greater dynamic loading than the steel rebar in civil engineering construction. The increased bonding capacity of a bolt is important when supported ground is either heavily fractured, faulted or the supported ground is of soft formation, typically that of coal measure rocks. Past laboratory studies have identified the bolt profile spacing as of significant relevance to bolt resin rock bonding increase, however, no attempt has been made to determine the optimum spacing between the bolt profiles spacing. Accordingly, a series of laboratory tests were carried out on 22 mm core diameter bolts, commonly used in Australian mines, installed in cylindrical steel sleeve. The study was carried out using both push and pull testing methods. The push test was carried out in 150 mm long sleeves while the pull testing was conducted in 115 mm long sleeves. Profile spacing tested include, 12.5, 25.0, 37.5, and 50 mm lengths. Additional studies undertaken include modelling the profile of the load-displacement data of pull testing. Bolts with a profile spacing of 37.5 mm were found to provide optimum load bearing capacity as compared to other tested profile spacings.

Jan 1, 2009

By Chris Mills

El papel de la separacion gravimétrica en la industria minera es brevemente considerado en perspectiva. Las pruebas e intentos de laboratorio y mineralógicas para el diseñio de los procesos gravimetricos son examinados poniendo especial énfasis en la selección de la tecnologia del proceso. Es tratado y comentado el material disponible en equipos para pequeña escala y trabajo de pruebas-piloto, particularmente en relación a la escalacion y a la adquisición de datos precisos y fiables. El transporte del comportamiento de los datos desde la planta piloto a la planta a escala es igualmente explicado. Son resefiados todos los tipos de equipos a escala total existentes para la separacion gravimétrica, poniendo de relieve las unidades de alta capacidad. Es considerada la disposicion de la planta y la seleccion de 1os equipos auxiliares.

Jan 1, 1982

By T. Hall, R. Ferris

Waterjets and diamond wire saws have raised the productivity and lowered the cost in dimensional granite quarries. While the cost of diamond wire sawing is substantially lower than waterjet, the judicial use of the waterjet can simplify and improve the overall operating efficiency and predictability. Granite is the hardest commercial stone and only the gem-stones garnet and diamonds are harder. The introduction of industrial diamonds has made it possible to quarry and process granite at costs equal to or less than other natural stones – making granite, with its superior properties, the best value available.

Jan 1, 2004

By Dirk Bleazard

Barrick Goldstrike Mines is improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. Identifying equipment failure modes and developing associated capital asset management practices can minimize failure consequences. Successful programs have included alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle. This results in an associated reduction to repair costs and equipment down time. Mining companies invest in their capital assets to provide the capacity necessary to meet operational needs. Over time, functional failures occur that reduce this productive capacity. Diagnostic technologies now exist that allow the condition of equipment to be monitored. Early response to this information minimizes the effects of functional failures and restores equipment re- liability. Reliability is a performance indicator of overall equipment condition. It is most often expressed in terms of mean time between failures. When the established objectives of a capital asset management program include the maximization of this failure interval, trailing indicators, such as availability and operating cost improve. The probability of equipment failure is influenced by engineering design and operating conditions. The performance level resulting from this operating environment is expressed as "inherent reliability." Without maintenance intervention, equipment will ultimately fail to perform its intended function and become less reliable. Therefore, maintenance must be managed as the supplier of reliable operational capacity. Maintenance can only supply equipment performance that approaches the level of inherent reliability. Actually achieving inherent reliability requires that all maintenance decisions are made at the economically optimal time. Enhancing performance levels beyond inherent reliability can only be achieved by altering operating conditions or practices or through physical equipment modifications. An evolution in maintenance management philosophy has been under way since the beginning of the industrial revolution. As equipment has become more sophisticated, so have maintenance practices. At the beginning of the industrial age, equipment tended to be over designed and slow moving. The first maintenance philosophy was one of reactive maintenance. Maintenance intervals were dictated by the operational status of the equipment. As a result, production interruptions were common and capacity needs were met through an investment in redundant capital assets.

Jan 1, 1998

By Sriram Padmanabhan, Jan M. Mutmansky

The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Utah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7. The results will be presented using two categories of data collected during two separate phases of the research: (1) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and (2) quartz concentration data from mines chosen at random. The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent.

Jan 1, 1989

By J. J. McDougall

The Windy Craggy copper-cobalt-bearing massive sulfide lies in the Tatshenshini map area of northwestern British Columbia, where British Columbia joins Alaska and the Yukon. The area is covered with numerous glaciers and ice fields that mask geologic detail and hamper ground access. In 1957, Ventures Ltd., the predecessor of Falconbridge Ltd., undertook a reconnaissance of the area using a float-equipped Supercub. At that time, large lakes and glaciers were unnamed and little was known of the geology. The prospecting team was led by J.J. McDougall with Stan Bridcut as pilot-prospector. Prospecting was directed at the St. Elias Mountains between the rich Kennecott copper deposits to the northwest and the Maid of Erin silver-copper mine on the Haines Road, BC. Reconnaissance flying in 1957 and early 1958 eliminated vast segments of the Kennecott-Haines Road terrain as being too inaccessible for mining. In 1958, the Supercub landed at an unnamed lake and the terminal moraine of an unnamed 12.9-km (8-mile) long glacier was prospected. The lake was called Tats Lake and the glacier named Tats glacier (short for Tatshenshini). Float of sulfide was found in the moraine. Follow-up investigation along Tats glacier led to the discovery of several small sulfide deposits and these were staked. Prospecting active glaciers in this area can be complicated because of drainage capture by eroding valley glaciers. Glacier capture resulted in the float from one mineralized area being deposited at different times in three widely separated moraines. Float of the Windy Craggy deposit, therefore, occurs along the course of older glaciers and at the base of the currently active ones. The problem of sourcing caused much additional Supercub reconnaissance. It is interesting to note that about 40 geographic names were given various features in this unmapped portion of the St. Elias Range, and these names were ultimately officially adopted.

Jan 1, 1991

By Barry J. Hansen, Ruston A. Ford

Production of mine backfill from the tailings produced in a proposed Crandon concentrator is described. A process has been developed capable of producing suitable fill for the mining method selected for the Crandon orebody. It maximizes the placement of pyrite underground as fill and segregates tailings into pyrite and nonsulfide fractions. To determine the suitability and engineering characteristics of the backfill product for use underground, laboratory and physical stope simulation model testing was conducted. The results of the testing and the application of those results to the design of the backfill system ultimately affecting mine geometry and subsequent mine production will be presented.

Jan 1, 1981

By H. L. Bourne

Not everyone understands the concept of mineral royalty. Mineral royalty is a fee paid to a landowner by someone who extracts a mineral commodity from the owners property. The royalty contract between the lessor and lessee contains clauses and conditions that are significant to both parties, e.g., annual m1n1mum, escalation factor, duration of the lease, reclamation and assignability. Comparison of royalty rates requires knowledge of many conditions that influence the value of a given deposit. People in several different professions benefit from shared royalty information.

Jan 1, 1989

By R. M. Wheeler

For years the blasting industry has recognized eight milliseconds as the minimum delay time interval required between charges in order for them to be considered to fire independently of each other. However, computer analyses of seismic recordings made of several surface mine blasts reveals that this time interval may not always be sufficient for adequate vibration separation to occur. In some situations a combination of short delay periods and low frequency vibrations can result in waveform reinforcement. Various analyses of seismic recordings obtained from single hole detonations can be used to predict delay intervals that may enhance or reduce blast vibration effects.

Jan 1, 1987

By Alexander Filimonov, Yury Bloshteyn

The development of a high-efficiency control system for mine ventilation is a complicated scientific and engineering problem. As a result of high-costs and difficult conditions involved in experiments for the development and investigation of mine ventilation systems, simulation is a critical task in cost reduction and productivity. The paper presents the description of a universal simulation model for controlled aerodynamic processes in an Underground ventilation Network (UVN). The high-efficiency programming tool to design and investigate mine ventilation control systems (MVCS) is also suggested.

Jan 1, 1991

By Haydn H. Murray

Common clay includes a wide variety of clay and other fine- grained rocks that are used in many ways. These clays are some- times classified as miscellaneous clay and shale. Most products made from them are fired and include such things as structural and face brick, drain tile, vitrified pipe, quarry tile, flue tile, conduit, pottery, stoneware, and roofing tile. Very large tonnages of these materials are bloated by firing to form lightweight aggregate, and large quantities are used in making portland cement (see the specific chapters in this volume). Uses not requiring firing of a finished product include filler for paint and other products and shale and clay used for packing dynamite in blastholes and for plugging oil and gas wells that are no longer in use.

Jan 1, 1994

By Henry P. Ehrlinger III, Latif Khan, John M. Lytle

The primary purpose of this project was to produce and test coal concentrates made from coal preparation plant waste fines for use in a slurry-fed gasifier. Concentrates from several individual waste streams were examined to determine their amenability as feedstock for a slurry-fed, slagging, entrained-flow gasifier. The tests included analyses of the plant feed and product, material balances, and estimates of gasification reactivity and of pumpability. The following preparation plant fines were examined: • fresh rejects produced in a plant processing underground- mined Springfield Coal • fresh rejects produced in a plant processing underground- mined Herrin Coal • fresh rejects produced in a plant processing surface-mined Springfield Coal and Herrin Coal • Five-year old impounded fines rejected during processing of underground mined Herrin Coal. At high coal recoveries the Btu content of the concentrates was greater than the Btu content of the utility product from the plant. The coal recovered from fines was found to be entirely acceptable for gasification and pumping without additives.

Jan 1, 1995

By Howard R. Postovit, Bonnie C. Postovit

Raptors are birds of prey. In recent years, these birds have become highly regarded and have been given protection under various state and federal statutes. Surface coal mining can have both negative and positive impacts on raptors. Mitigation strategies and enhancement techniques can be implemented to alleviate negative impacts. The success of habitat reclamation will determine the long-range impact of mining on raptors.

Jan 1, 1989

By Gao Zhizhong, Zheng Shibo, Gu Zhengxing

Extensive research on the beneficiation of Florida dolomitic phosphate pebble has been carried out by Lianyungang Design and Research Institute of China (CLDRI) in recent years. Test results indicate that the fine-particle flotation process could be used to effectively recover the phosphate values from Florida high-dolomite phosphate resources. With the CLDRI fine-particle flotation technology, a phosphate concentrate with 31% P2O5 and less than 1% MgO could be obtained from a flotation feed containing 25.8% P2O2 and 2.2% MgO at an overall P2O5 recovery of up to 85%.

Jan 1, 1999

By J. P. Savely, D. E. Nicholas, R. D. Call

Slope stability is a probabilistic phenomenon and as such should be analyzed with probabilistic methods. Fracture orientations alone, insufficiently model the rock mass. Other parameters describing the fracture set characteristics are required with distributions that can be sampled to fit mathematical stability models. Important considerations are length, spacing, dip, waviness angle, and overlap. These parameters are of major concern in design and are difficult to measure. Reasonable estimates of the characteristics can be used to provide distributions.

Jan 1, 1977

By Ralf Vergeiner

The most famous landmark of the city of Graz (Austria) is the clock tower on the castle hill. An underground chamber was built as a multifunctional structure beneath this landmark. The required structure was designed as cavern. The overburden to the clock tower in the north side of the cavern was only 30 m. To allow access from the city to the chamber and the clock tower, a vertical shaft was built near the cavern. Rock excavation was by drill and blast method. The pilot shaft was made by the raise-boring method. Because the location of the building site was in the center of Graz, special care was taken to minimize deformations and vibrations so as to protect surrounding buildings.

Jan 1, 2001

By Gerald J. J. Aleva

Lateritization is a surface and near-surface process enhanced by a humid and warm climate and by good drainage. It closely follows the development of the regional landscape. The cyclic landscape development on the Guiana Shield is accompanied by a progressively thicker and more evolved laterite mantle the older, and hence in most instances the higher the planation level. The known, economically interesting bauxite and aluminous laterite eposits of the Shield are restricted to the remnants of the oldest of the Cainozoic planation levels (level I1 and 111).

Jan 1, 1984

By D. R. Maneval

The vast coal resources of North Slope, Alaska, can be expected to attract substantial interest because the nearly flat-lying coal beds of the coastal plain are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large-scale coal mining and reclamation operations have not been carried out in the arctic. The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the inter-relationship between the problems due to permafrost and factors in reclamation of post-mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1987

By Mark Kuchta, Hans Engberg

The Swedish mining company LKAB operates two of the largest underground mines in the world today that together produce around 35 Mton of iron ore per year. During the 1990s, the company embarked on a massive effort to computerize its mine planning system. The goal was to combine various mine planning operations including mine surveying, geologic modeling, mine layout, production planning, and production follow-up into one modular based integrated system. The system was built around a large Oracle database and the Microstation CAD system. This overall design strategy and the various system modules are described, and some experiences gained using the system are discussed.

Jan 1, 2002