Search Documents

By Eli Curiel, Ingar F. Walder, Patrizia P. Schuster, Walt Keyes

Mansfield Canyon, of the Wrightson Mining District, Santa Cruz County, Coronado National Forest, Arizona, was actively mined in the late 1800's and early 19001s, with minor activity until 1953. The main products were lead, silver, copper, zinc, and gold occurring in polymetallic quartz veins. The canyon contains numerous adits and waste dumps, some of which generate metal-loaded acid. Samples of seeps, waste dumps and bedrock have been collected for various analyses: metal concentrations, acid base accounting (ABA), and water quality to evaluate the extent of oxidation and metal release from the start of mining until present, the potential impact, and reclamation options. Although the waste-rock piles within the canyon are small (2,000-10,000 tons), they have a high sulfide content with little or no neutralizing capacity. It is planned, therefore, to move the waste piles either to a constructed repository site within the canyon or to a copper leach facility to be used as an acid generator.

Jan 1, 2000

By John R. Twining, Michael D. Lawton, Ross A. Jeffree

The Finniss River system in tropical northern Australia has received 'acid-drainage' contaminants from the Rum Jungle uranium/copper mine site over the past 4 decades. Following mine-site remediation that began in 1981-82 the annual contaminant loads of sulfate, Cu, Zn and Mn have declined by factors of 3, 7, 5 and 4, respectively over 1990-93, compared to the 1969-74 pre-remediation loads. Comparison of the frequency distributions of contaminant water concentrations over these pre- and post-remedial periods have shown varying degrees of reduction in the highest levels following mine-site remediation, that are consistent with reductions in their annual-cycle loads. Among the three selected major metal contaminants the reductions in maximum water concentrations are most pronounced for Cu. The demonstrated reductions in the highest water concentrations of all four contaminants are also associated with previously reported ecological improvement in the Finniss River system, compared to the benchmark of environmental detriment established in 1973fl4, prior to the beginning of remediation at the mine site.

Jan 1, 2000

By A. Mehmet, W. A. M. te Riele

A pilot-plant investigation in a NIMCIX contactor has shown that activated carbon can extract more than 93% of the gold in return-dam solutions. The average gold concentration in the barren solution was less than 0.003 mg/L from a feed averaging 0.048 mg/L. The carbon was eluted by the Zadra procedure. The operating conditions of the elution-electrowinning circuit are reported, and the elution of the gold and other metals is discussed. The reactivation of the carbon by use of the Rintoul kiln is described, together with the results of reactivation. The consumption of reagents in the process cycle is presented in sufficient detail to allow the economic viability of this technique to he evaluated for the recovery of gold from low-grade solutions.

Jan 1, 1990

By R. H. Seraphim

The name is derived from an Egyptian myth, "A beautiful lone bird which lived in the Arabian desert for 500 or 600 years and then consumed itself in fire, rising renewed from the ashes to start another long life." HISTORY This account of the first history is gleaned from old reports and documents which are listed in the Bibliography and from discussions with old-timers of the district. Prospectors were active in the vicinity of Greenwood in 189 1, and in that year staked the Mother Lode, Crown Silver, and Sunset. Henry White staked the Knob Hill claim in Phoenix on Jul. 15, 1891, and by the end of the year, other prospectors had staked most of the claims covering the valuable ore bodies in the camp. Much surface work done in the early years indicated that the values in copper, gold, and silver were low. Large capital investments were required to develop the ore bodies and build smelters. The discovery that the ore was practically self-fluxing greatly enhanced the value of the deposits. A map of the area showing the geology is given in Fig. 1. The bedded Brooklyn conglomerate is shown in Fig. 2.

Jan 1, 1991

By Jeffrey P. Chanton

A specialized Pore-Fluid Array sampler (PFA) was designed to collect and store pore-fluids to monitor temporal changes of ions and gases in gas hydrate bearing sediments. We tested the hypothesis that pore-fluid chemistry records hydrate formation or decomposition events and reflects local seismic activity. The PFA is a seafloor probe that consists of an interchangeable instrument package that houses OsmoSamplers, long-term pore-fluid samplers; a specialized low-dead volume fluid coupler; and eight sample ports along a 10-meter sediment probe shaft. The PFA was deployed at Mississippi Canyon 118, a Gulf of Mexico hydrate site. A 160-day record was acquired from the overlying water (OLW) and 1.3 meters below seafloor (mbsf). Fluids were measured for dissolved chloride, sulfate, and methane concentrations and dissolved inorganic carbon and methane stable carbon and deuterium isotope ratios. Chloride and sulfate did not change significantly over time, suggesting the absence of gas hydrate formation or decomposition events. Over the temporal record, methane concentrations averaged 4 mM at 1.3 mbsf and was thermogenic in origin (d13C-CH4 = -32.4±3.4?). The timing of an anomalous 14 mM methane spike coincided with a nearby earthquake (Mw=5.8), consistent with the hypothesis that pore-fluid chemistry reflects seismic events. Keywords: Osmosampler, gas hydrate, methane, stable isotopes

Jan 1, 2008

By Timothy C. Smith, S. Andrew Jacobs, Douglas E. Gonzales, Sandy J. Schexnailder, Carl Urban

At the Schwartzwalder Mine (Cotter Corporation, Golden, Colorado) ion exchange resins have been used in mine water treatment experiments. The experiments, initiated in October 1979 and currently in progress, demonstrate that mine water uranium values can be reduced to levels as low as 10 ppb. Duolite® A-101D, a strongly basic anion exchange resin, was tested in laboratory-scale columns (1 inch diameter) initially and then in pilot-scale columns (4 inch diameter), using both co-current and counter-current operational modes. Observations and conclusions resulting from these studies can be summarized as follows: (1) Duolite® A-101D appears to have successfully extracted uranium at influent levels of approximately 2.0 ppm over multiple loading and elution cycles, consistently producing effluent concentrations as low as 10 ppb uranium. (2) Based upon present test data, counter-current regeneration appears to be the key to successful operation. Upflow loading and downflow elution are the preferred modes for service and regeneration, respectively. (3) Filtration is a necessary pretreatment to remove fine clay and inorganic precipitates that will foul the resin, causing excessive pressure drop and poor loading and elution kinetics. (4) This waste treatment application is unique in that it offers the opportunity to recover some or all of the capital investment in the treatment facility

Jan 1, 1980

By L. B. Hales

The advent of the process control computer with its capabilities of monitoring, storage, and real-time control has revolutionized control technology in the mineral industry. Initial efforts to introduce the computer into process control began in the early 1960's. However, it wasn't until the last decade with the introduction of integrated circuits and minicomputers that truly successful applications became visible. Computer hardware and real-time operating software have improved to the point that they rarely provide major problems in the implementation of successful control systems. At this time the most prevalent problems and obstacles affecting the successful implementation of a control system are as follows: (1) reliable and representative sampling systems; (2) rugged and reliable process sensors; (3) the availability of well-defined control strategies; (4) the willingness of plant management to provide the continuous support necessary to acquire and/or train appropriate personnel in the operation and maintenance of advanced control systems. Discussion of these problems and of the instrumentation required for the successful application of computers in minerals processing plants follows. In order to enhance this discussion the remainder of this subsection is broken up into individual mineral processing categories.

Jan 1, 1979

By Abou Saghafi

In order to investigate the design parameters of a future longwall in a thick coal seam a numerical model of gas emission from the goaf area was developed. A Longwall goaf was modelled as a collection of different size coal blocks. For each coal block the partial differential equation of gas flow was independently solved. In developing the flow equations, both pressure-driven and diffusion driven gas flow regimes were considered. The total gas emission rate was calculated by integrating the gas release from each individual coal block over the whole goaf area. The main output of the computer program are gas flowrate from goaf and residual content of caved coal in the goaf as a function of distance from the face. The model was applied to a longwall face driven in a thick seam where large volumes of coal in the roof were to be left behind the face. The gas contained in the coal was mainly CO, with a high desorption rate. Simulations were under- taken to quantify the effect of size of the caved coal on the flowrate from the goaf. The flow properties of coal, such as diffusivity, permeability and coal swelling due to gas adsorption, were directly measured on coal samples from the seam.

Jan 1, 1996

By E. J. Meets, C. F. Meyer

Bord and pillar mining at shallow depth (400 m approx. maximum) is widely used in South African coal mines. One of the problems encountered in extracting coal in this manner is the ventilation of advancing bord and pillar headings. The traditional ventilation methods of force, exhaust and overlap (force/exhaust) are reasonably effective but tend to be both cost and labour intensive. Ducting often restricts the available free area of roadways thus impeding the transport of coal and other materials inbye the coal production section. Due to the above facts, ductless fans are currently being used to minimize the amount of ducting required in advancing sections. Two different types of fans are used, namely, vortex fans and the so-called `jet' fans. Vortex fans were developed from the fan blade design used for vertical take-off aircraft. The fans have the capability of delivering air over distances of about 30 m in the underground situation without any ducting attached to it. Jet fans are standard axial flow fans fitted with outlet reduction pieces which increase the velocity pressure at the discharge to such an extent that the air delivery distance is improved to almost match that of vortex fans. The paper describes some applications of both these fan types in advancing bord and pillar sections.

Jan 1, 1993

By B. Moudgil, Hassen El-Shall

Particle shape and size distributions are among the most important parameters that affect the filtration efficiency of phosphogypsum in wet- process phosphoric acid production. Cost-effective enhancement in filtration rate is desired by phosphoric acid producers for higher plant capacity and lower operating costs. In this regard, numerous research efforts have been carried out in different laboratories as well as in pilot and plant testing. Nevertheless, changes in phosphogypsum crystal shape and size distribution deserve special attention. In this study, the results obtained in the presence of Crysmod and Hiflo-S5 surfactants are discussed. The influence of such additives on crystal morphology and size distribution are studied under different sulfate contents (supersaturation). The obtained data are correlated with process efficiency parameters such as filtration rate, digestion of rock, and recovery of phosphate values. Up to 60% increase in filtration rate is obtained. In addition, an increase in digestion efficiency and P205 recovery is achieved due to addition of surface active agents. The observed beneficial effects are explained in the light of the changes induced in crystal habit, size, and size distribution.

Jan 1, 1999

By Scott G. Britton

Thin-seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges can be further amplified depending on such factors as labor unions, federal and state regulations and market characteristics. This article explores the turnaround situation occurring at Tanoma Mining Co. (TMC), a medium-sized, underground coal mining company in central Pennsylvania. The company has used a systematic approach of improving management controls and direction, labor relations and communications to improve its cash flow from negative to positive within a projected five-year span. An intensive upgrade-rebuild-replacement program for mining equipment and systems has also been established to support other management activities. Discussion Thin-seam coal mining is an industry within the broader industry of coal mining. Thin seam mining faces the same cost pressures and engineering problems as its higher-seam competitors, without the advantages of moving volume per foot of extracted material. To stay at economic parity with others requires additional creativity within the management team to extract higher productivity gains from the existing workforce and mining systems. The Tanoma operation is a deep mine in Indiana County, PA, about one hour northeast of Pittsburgh. Coal is extracted from the Lower Kittanning "B" seam. It lies about 91 m (300 ft) below the surface and averages 0.9 m (I ft) in height. Continuous mining units using mobile bridge conveyors or shuttle cars

Jan 1, 1991

By B. K. Mishra, R. K. Rajamani, A. D. Joshi

The liners are the most important part in the SAG mill operation. Hence, the liners and their design parameters are primarily studied to see its effect on SAG mill operations. Effective liner designs are directed to reduce downtimes, which is needed for the replacement of worn liners. There exists constant chance of improvement in the capacity of mill by studying the effect of liner design on the charge motion inside the mill. This need is satisfied by three-dimensional discrete element code "Millsoft", which uses Discrete Element Method (DEM) to analyze the motion of charge. This simulation of SAG mill keeps track of all the moving bodies like ball and rock and observes its interaction with liners and lifters. The recent work done on this software helps generating mill to more reality by putting conical wall at feed and discharge end, over the earlier flat walls. Millsoft is an effective tool to watch the change in the motion of the charge due to different types of lifter bars and different design parameters. It was concluded that by simply increasing chord length between the lifters and increasing the face angle of the lifters, capacity of the mill could be increased. On the other hand, this software can also be used to get power draft at the respective mill design.

Jan 1, 2002

By Hassan El-Shall, El-Sayed A. Abdel Aal

The major goal of this study is to decrease iron content in wet-process phosphoric acid. Reducing the amount of post-precipitated sludge in the acid is another important objective in this investigation. In order to achieve these goals, research efforts have focused on bench scale testing of an iron-chelating reagent to remove iron from phosphoric acid produced from South Florida high-iron and -magnesium phosphate concentrate, and plant testing using freshly produced concentrated acids for reducing the post- precipitated sludge. The data obtained in the above studies suggest that the addition point of the precipitating reagent is very important, as the precipitated iron compound has higher solubility at higher P2O5 concentrations. Up to 60% Fe2O3 removal efficiency is achieved depending on the amount of the reagent, concentration of acid used, and operating conditions. The addition of precipitating reagents to freshly concentrated phosphoric acid leads to a decrease of up to 84% in sludge volume percentage depending on acid type and clarification conditions. Decreasing the volume percentage of the sludge facilitates acid handling as well as decreases the adherent water- soluble P205 leading to lower total P2O losses.

Jan 1, 2002

By William S. Brack

The mining industry is very capital intensive. Competition for shareholder investment has never been greater. Among our challenges is the need to meet shareholder expectations (return on investment), and one area of focus lies in our ability to deliver value on our capital investments. Our ability to meet project expectations affects not only the economics associated with the immediate project but also directly influences our ability to finance future projects. Moreover, our ability as individual companies to attract investor capital is influenced by how we have done overall as an industry, and our industry track record has not been that stellar. With safety, scope, cost, schedule, and quality as guiding principles, our project managers today must address high expectations on every project. This paper examines some items that should be on today's project management checklist. PROJECT ENGINEERING Herbert Hoover, himself a mining engineer, said Engineering is a great profession. There is the fascination of watching a figment of the imagination emerge through the aid of science to a plan on paper. Then it moves to realization in stone or metal or energy. Then it brings jobs and homes to men. Then it elevates the standards of living and adds to the comforts of life. That is the engineer's high privilege.

Jan 1, 2004

By Numan Elmas

This paper presents detailed information on the genesis, formation, and industrial utilization of Yaylacik magnesites. Tectonically, the study area is located within the Tavsanli Zone, immediately south of the Izmir-Ankara suture in western Turkey. The geologic setting mainly comprises ophiolitic melangks basics, and ultrabasics associated with very rich magnesite deposits and lacustrine sediments. The ophiolitic unit tectonically overlies the schists and carbonate rocks. The presence of glaucophane and lawsonite indicates a low-temperature/high-pressure metamorphism. The ultra- basic rocks, which exhibit cumulate composition, have been mostly serpentinised and represent the oceanic floor of the Yaylacik ophiolite. Basic intrusives consist of dolerite and diabase, and they show the characteristics of within-plate dolerites. The magnesite occurrences are commonly observed in block, stockwork, lens, and vein forms and were deposited within the serpentinites. In most magnesite samples, secondary quartz/chalcedony formations are observed as fracture fillings due to the highly effective tectonic movements. Field surveys and microscope studies reveal that magnesites had been formed by the metasomatic alteration of serpentinites. Chemical analyses show that, although MgO content of the magnesites varies from 43.41% to 50.48%, Fe203 and CaO are lower than 1%. Silica contents are as high as 5.52% in a few samples. Although Yaylacik magnesites are not suitable for making basic refractory bricks, they are widely used as caustic-calcined magnesite in a variety of applications, including animal food, artificial fertilizer, chemical (acid neutralizer), medical and pharmaceutical, and water treatment.

Jan 1, 1999

By Byron V. Knelson

Although the concept of centrifugal recovery has been around in one form or another for many years, it has not been until recent times that it has become clearly understood and properly put into perspective. Simplistic in theory, it is when one begins to examine the variables involved that the true complexities of this matter begin to emerge. In creating an enhanced g force concentrator, there are many aspects both positive and negative that are encountered. Many conditions that are inherent to all conventional 1 g concentrators do not apply to centrifugal concentrators and therefore very few cm factors exist between them. In developing this technology, virtually all principles were proven by method of trial and error. Among the topics discussed are the effect of g force enhancement on particulate behavior with respect to size and shape, density, enrichment, fluidization, and the "teeter principle". In addition, we will discuss the physical effects of g force enhancement with respect to manufacturing in the areas of abrasion, bearings, and vibration. In discussing the recovery parameters of centrifugal concentrators we will draw direct comparisons to various other recovery methods, outlining the conditions most favorable to their application.

Jan 1, 1988

By M. Karmis

Surface subsidence has been recognized as an inevitable consequence of underground coal mining for several centuries. The damage resulting from this phenomenon has been witnessed in rural as well as in urban areas and ranges from simple land settlement to severe structural damage to buildings. Subsidence prevention is not feasible, at least under the existing technological and economic constraints of underground coal mining. Using a rational method of subsidence prediction, it has been demonstrated in many coalfields that subsidence control can be successfully practiced in order to reduce and accommodate subsidence within environmentally acceptable levels. This paper presents the development and testing of a subsidence model, based on the zone area method. This technique is a refined development of the influence functions and it is capable of investigating a mining plan of any shape, thus facilitating both longwall and room-and-pillar mining systems. More specifically, this study can be divided into two major efforts: (a) The development of the zone area model. This formulation was designed to accommodate the analysis of an optimum number of zones, over the area of interest, both accurately and efficiently. (b) The testing of the computer techniques with appropriate field measurements. In order to accomplish this, published as well as unpublished information was collected and analyzed according to a regionalized scheme. This procedure minimized differences in subsidence characteristics between the various coalfields and allowed a regional validation of the predictive capabilities of the model.

Jan 1, 1982

By Robert F. Randolph, Arnold C. Love

This study describes the positioning strategies used by operators of radio controlled underground mining machines. The observations have implications for task design to insure adequate visibility and task performance. Radio controlled continuous coal mining machines have allowed many mines to increase safety and production by placing human operators away from the hazards of an unsupported mine roof. The operator is no longer confined to an operators component and visibility can be enhanced with proper positioning. Also, the operator is no longer subjected to the shocks and vibrations of the mining machine. The operator's ability to move freely about the worksite requires a careful analysis of several competing safety and production considerations. Thirty-five operators of remotely controlled continuous mining machines were observed using work sampling followed by interviews to determine where the operator was positioned and what he or she was watching. These observations were separated according to the task being performed by the continuous mining machine and summarized as position density plots. The specific task of tramming in reverse through a crosscut is analyzed along with more general summaries of the time miners spend outside of the policy-defined operating positions while performing other production tasks. The operators were: observed to frequently vary from company standard operating procedures (SOP). Many of the variations from company SOPS were based on task demands. Interview responses indicated that portions of the mining task place visibility demands on the operators that are difficult to accommodate within existing procedures. An improved task design process would include these visibility requirements. Also, the operator's vision can be augmented thorough video cameras in future teleoperated mining systems, and the operator can be increasingly isolated from environmental hazards.

Jan 1, 1992

By E. T. Sugar

English China Clays, the world's largest producer of China Clay, has its main production capacity in the South-West of England, where a complex of pits, refining plants, dryers and ports covers an area of approximately 100 square kilometres. The possibility of a computerised information network was first considered in 1980. The system was required to provide information at the central level and also at local plant level to improve co-ordination and control. Immediate access by any authorised user, and flexibility of interrogation were important aims. A small micro-based prototype system was implemented in 1981, and later that year development of the mainframe system commenced. This latter system will provide at least one terminal in every works location and will allow inter-communication of laboratory test data as well as detailed stock levels and production data. An integrated system for order processing will allow stock levels to be monitored in relation to anticipated requirements. The system has been developed by the Data Processing Department using the IDMS database package running on an ICL ME29 mainframe. It was decided to use microcomputers as terminals, which although more complicated because of protocol emulation allows stand-alone applications to be run on the same equipment. Those applications concerning Production Planning are outlined in the paper. Communication on the network is by synchronous transmission over dedicated lines. All data is stored on the central database with terminals accessing it in a star configuration. The system is currently partially implemented with 30 available screens at 18 separate worksites.

Jan 1, 1986

By V. Enns, E. Soprovich, J. H. G. Laflamme

A mineralogical and geochemical characterization study was carried out on arsenic-bearing Ketza mine tailings to complement a column extraction test program with the purpose of assessing the potential of arsenic mobilization from the tailings. Two types of tailings samples (i.e., exposed tailings from the impoundment area and water covered tailings samples) were subjected to column tests under standing water cover and with no water cover but weekly flow-through flushing. The tailings have a uniform size distribution. The samples are characterized by high Fe2O3 (44.0 to 68.2 %) and As (3.7 to 4.4w%) concentrations. Ferric hydroxides are the dominant species that are mostly amorphous or cryptocrystalline. Arsenopyrite, scorodite, an Fe-Ca arsenate hydrate phase, an Fe-Bi-As phase and ferric hydroxides are the arsenic-bearing minerals. Arsenic is essentially contained in Ca-As goethite, Fe-Ca arsenate hydrate phase and scorodite. Goethite, although containing low levels of arsenic, could be a significant arsenic-bearing phase because of its high abundance. There does not appear to be any significant chemical or mineralogical difference between the original exposed tailings and the material left underwater with no flow-through for over a year. There are differences in terms of CaO, Fe2O3, SiO,, As, goethite, scorodite, calcite and dolomite concentrations between the exposed tailings and the column material after undergoing approximately two-year flow-through and aggressive leach tests. These differences are likely to be resulting from a combination of different column test conditions and sampling or heterogeneity of the material.

Jan 1, 1998