Search Documents

By Donald Lau, Adrian Crawford

In the field of grouting, practitioners fre¬quently advocate procedures that are often unique and contradictory. As a result there has been considerable debate as to what constitutes optimum grouting practice. A knowledge of both the rheological properties and the flow characteristics of grouts is essential to the development of a rational understanding of the grouting process. Flow models and viscosity experiments have been conducted using cement grouts comprising High Early Strength Portland and Microfine cements. The addition of superplasticizers was found to enhance the flowability of the grouts as well as to reduce the effective groutability ratio. Steady state flow equations and design charts for predicting the radial penetration of cement grouts have been developed.

Jan 1, 1986

By A. J. Friedrich

Conveyor belts are designed to go unnoticed. When they work well, they attract little attention. When they are not doing the job right, it is noticeable, and they need to be fixed immediately. Vulcanising contractors compete for the maintenance of belts in mining/quarrying and general materials handling worldwide. Damage repair is approached in similar fashion. The damaged section of belting is normally cut out and discarded, and the belt re-spliced using hot vulcanising, Cold splicing, or mechanical fasteners/clip joints. However, there is a cost-effective alternative, alleviating the need to remove damaged sections which are often perfectly recoverable. This is the use of cold-curing repair resins and adhesives.

Jan 1, 2000

By J. Paraszczak

With regards to the cost and profitability of a mining operation, the performance of the equipment employed is one of the key issues. Cost and profitability depend on, among other factors, the reliability and availability of the equipment. In an attempt to reduce equipment downtime, it is indispensable to collect and analyze reliable data and information on failures and maintenance actions. This paper reviews common problems encountered in this respect, with particular emphasis on the lack of uniform terminology and methodology. Recommendations concerning the standardiztion of reliability and maintainability concepts and measures are given. Regarding the benefits that the latter may bring, the paper concludes with a proposal for an industry-wide initiative in this respect.

Jan 1, 2002

By G. H. Jardine

Mine planning and production scheduling in surface mines are basically iterative processes which are ideally suited to the use of computer-based techniques. Both processes are truly three-dimensional and lend themselves to the application of 3-D interactive graphics. Until recently, this has applied the need for the costly, dedicated graphics screens and mid range minicomputers. However, ongoing advances in processor chip design led to the emergence of inexpensive and powerful 5 to 10 Mips desktop work- stations. These workstations have the processing power to support rapid, high resolution, 3-dimensional graphics. By combining these workstations with powerful 3-D CAD software and, with a suite of comprehensive mine planning and scheduling applications, Mincom has developed a most cost effective solution to modern mine planning challenges.

Jan 1, 1989

By Malcolm J. McPherson

This paper describes the algorithm used in a BASIC program for an IBMXT microcomputer, to simulate the underground mine climate. The program called CLIMSIM has been developed and refined over several years as a result of considerable use at operating mines. The program has been designed to be easy to use and be understood by the practicing mine ventilation engineer. It provides predictions of the work place climate, so that the optimum ventilation/cooling system can be designed to obtain a certain air cooling power or effective temperature at the work place. An example is given of the application of the program to a mechanized cut and fill stope at the Homestake gold mine in South Dakota.

Jan 1, 1986

By R. Costa, A. Kozak, B. Fukuhara

Introduction The Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc. The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain. The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mined has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. and now Yamana Gold Inc.

Jan 1, 2007

By J. R. Mattern

The engineering geology of the Rio Tinto Borax Boron Mine creates challenges in providing practical slope design recommendations to mine planning engineers. Low strength sedimentary units interbedded with very low strength lakebed clays surround the orebody. Faulting has offset and juxtaposed these units into variably adverse orientations, while groundwater is compartmentalized both vertically and horizontally within fault blocks. A collective program of geologic data collection, geomechanical strength testing, geologic modeling, slope depressurization, confirmation of underground stope locations, and documentation of slope behavior provides vital information for design investigations and sensitivities. Analysis results lead to risk assessments and operational procedures that add value to the business by optimizing slope configurations and minimizing risk.

Jan 1, 2004

By G. A. Munoz, J. D. Miller

Gold leaching of an auriferous pyrite ore from the Portovelo deposit in Ecuador indicates that noncyanide leaching systems, such as thiocyanate and thiourea, are not as effective as the traditional cyanide system. For example, whereas approximately 95% of the gold can be leached from the ore with cyanide, only about 50% gold dissolution can be achieved with a thiocyanate leaching system. Electrochemical measurements indicate that gold is not cathodically protected by pyrite in these systems. Based on the results of preliminary diagnostic experiments, it appears that gold dissolution in thiocyanate and thiourea systems is limited by passivation due to the formation of either elemental sulfur or sulfur compounds on the gold surface.

Jan 1, 2000

By Walter R. Jr. Hibbard, William A. Vogely

INTRODUCTION Volatile markets and pricing, increasing imports, constraining but effective laws related to the environment, health and safety and price controls lead to concerns which generated pious laws stating non-fuel policy and authorizing studies but resulting in ineffective implementation. Several commissions, reports by the Secretary of Interior and even the President have led to many recommendations but little or no action. No single comprehensive policy could solve problems which are diverse, commodity specific and not categorizable (Landsberg 1982, 1983). Thirteen laws administered by 27 agencies regulate or affect minerals and materials. Political instability created by communist regimes in Southern and Central Africa jeopardized sources of critical imported materials. This situation led to a Resource War mentality. It was feared that the U.S.S.R. was seeking to control this area and exclude the United States from resources (Vogely, 1980). The success of the Organization of Petroleum Exporting Countries with a petroleum cartel led to fears of an Organization of Minerals Exporting Countries which might create more cartels and/or make the existing ones more effective. Economic needs of developing countries required export to maintain employment and balance of payments have led to world surpluses, weak markets, low prices, and large loans from the World Bank which have under- mined U.S. industry (Landsberg, 1982a). Un- cooperative environmental laws, obsolete facilities and non-competitive costs have led to shipping U .S. ores to other countries for processing into ingot and bars which are imported back to the United States. Yet massive internal turmoil has interrupted supplies, and led to un- certain availability and higher prices. This situation could happen again. Included in this category of critical materials with uncertain sources are metals required in the manufacture of military aircraft, which has led to concern regarding the defense industry base (Morgan 1983). Remedies have been proposed which include: updated stock piles, material substitution, international cooperation and coordination, foreign policy aimed at resolving racial and national stresses in South and Central Africa, relaxing U.S. environmental and public land regulations and action under the Defense Production Act (Goth 1982). The President's report (1983) to Congress has stated a national materials policy which recognizes: that materials play a critical role in our economy, defense, and standard of living; that public lands contain a vast untapped mineral wealth; that the role of government is to identify mineral issues and act on them; and that there is a need for long term high potential pay off research (Bureau of Mines 1983). There is a serious question as to whether or not a comprehensive national mining, minerals, and materials policy is feasible let alone necessary. One solution is to abandon the attempt at comprehensiveness and to target specific is- sues with realistic policies (Comptroller General 1979). In the following sections, the major studies of the 1970s will be reviewed, major issues yet to be faced will be identified, the principles involved in these resolutions will be reviewed,

Jan 1, 1985

By D. E. Ranta, John G. Stone

One of the steps in an ore reserve estimate is customarily a rigorous calculation of the in situ grade of the orebody itself. The result of this calculation is usually reduced by some purely arbitrary factor to force the calculation to agree with the observed grade of ore actually mined. The failure of the calculation to realistically depict the grade of ore actually extracted is in many instances not the result of either an incorrect calculation procedure or of sloppy mining practice, but is a direct consequence of unsuspected irregularities in the contact between the orebody and the surrounding wall rock. A pattern of holes spaced at 1.5-3.Om foot intervals, drilled as part of a pre-development program, will often reveal that a presumed "regular' ore/waste contact is, in fact, so highly irregular that it will be next to impossible to separate ore from waste during mining. In such an instance, 'fingers' of waste projecting into the mining block will substitute for equal volumes of ore left outside the mining limits. As a result, the grade of material actually mined will be less than the grade envisioned for the orebody. The volume of waste substituting for ore in the mining block is about 0.4X, where X = the average error in projecting the ore/waste contact between alternate holes in the test pattern, and is expressed in units of volume per unit of area of the contact surface.

Jan 1, 1992

There has been some confusion over the selection of discount rates when performing stochastic simulations of a project's net present value (NPV) using risk- adjusted discounting techniques. Some argue that lower discount rates should be used when performing stochastic valuation simulations. This creates higher NPV values and improves the attractiveness of a project. Others argue that the discount rate should not be lowered for these simulations. This paper exposes the source of this confusion. It demonstrates that stochastic simulations do not remove the risk inherent in a project and, therefore-do not improve a project's value to the risk-averse investor. Risk-adjusted discount rates should, therefore, not be adjusted downward when performing stochastic NPV simulations. Stochastic simulations are, however, shown to he useful in several aspects of project valuation.

Jan 1, 1996

By John R. Turney

MARY KORPI: Harry Hinds will be filling in for John Turney today. Harry is an exception to the industry these days, in more ways than one. He has worked for the same mining company for 33 years. That is something very few of us can claim. He is currently metallurgical superintendent for Homestake Mining Company in Lead, South Dakota. Harry is also the envy of many of us as he will be retiring this year and working on lowering that handicap! Harry will be discussing the "Role of Consultants."

Jan 1, 1998

By Michael P. Foose

In 1994, more than 41 of the approximately 160 coal-fired, electrical- power plants within the six-state Ohio River Valley region used flue-gas desulfurization (FGD) units to desulfurize their emissions, an approximately 100% increase over the number of plants using FGD units in 1989. This increase represents a trend that may continue with greater efforts to meet Federal Clean Air Act standards. Abundant limestone resources exist in the Ohio River Valley and are accessed by approximately 975 quarries. However, only 35 of these are believed to have supplied limestone for FGD electrical generating facilities. The locations of these limestone suppliers do not show a simple spatial correlation with FGD facilities, and the closest quarries are not being used in most cases. Thus, reduction in transportation costs may be possible in some cases. Most waste generated by FGD electrical-generating plants is not recycled. However, many FGD sites are relatively close to gypsum wallboard producers that may be able to process some of their waste.

Jan 1, 1999

By S. Subramanian, K. A. Natarajan, D. N. Sathyanarayana

FTIR spectroscopy is used to study the ad¬sorption of an oxidized starch on hematite, corundum, and quart: substrates. The difference spectrum of the adsorbed starch on hematite indicates surface reactions involving -CH2OH and -COH groups and shows striking similarities with that of the ferric-starch system, suggesting chemical interaction between the iron of hematite and the starch adsorbate. The IR spectra of starch adsorbed on corundum and quart: show no evidence of chemical interaction, although hydrogen bonding is apparent. The extent of adsorption of starch on hematite. corundum, and quartz decreases along the series. The evidence for chemical interaction of starch with hematite is further obtained by the X-ray photoelectron spectra of starch adsorbed on hematite, showing noticeable decrease in peak positions of O(Is) and C(Is) of free starch. The Mössbauer spectrum of hematite with stanch adsorbed on it complements these findings.

Jan 1, 1990

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

By Donald E. Hulse

Selection of a block size for a computerized 3 dimensional ore body model is an exercise in compromises. Larger blocks decrease the use of computer resources and decrease the variance of the block estimates. Smaller blocks increase the resolution of the model and the selectivity which can be used in the planning, but increase the variance of estimates in the individual blocks. A common rule is that blocks can be as small as one fourth the average sample spacing, however this ignores the interrelationship between the block size, the sample spacing, and the variogram model. This paper will explore this relationship Kriging estimation variance will be used as a comparative measure of estimate quality. Graphical techniques will be used to show that there is a point where smaller block sizes cease to contribute to the resolution of the model. A method of evaluating the consequences of block size decisions will be examined.

Jan 1, 1992

When exploration shows a mineral deposit to be of importance, the subsequent work of defining the limits or boundaries of the ore body and preparing it for the extraction of the mineral is termed development (Young, 1946). In underground mining, development also connotes the work that is involved in opening up a deposit preparatory to stoping or productive operations. In this section, mine development is defined to include all studies and operations that will enable a sound evaluation of an explored ore body from the technical and financial standpoints. Though the ultimate objective of all mine development activities is the same, the scope and detail of these activities vary depending on the type of ore body (e.g., flat bodies, lenses and sheets, massive deposits, narrow veins, and bedded deposits), and the method of working the deposit (e.g., under- ground or surface methods or a combination of both of the methods). Therefore, the various contributions in section 3 address such topics as long-range planning, feasibility studies, and valuation for many types of ore bodies and different mining methods. This introductory review is divided into three major parts. In the first part, long-range planning aspects are briefly discussed with .an emphasis on current trends that affect mine planning. In the second part, an overview is provided of the contents in the mine development and valuation section. In the last part, remarks are made on the status, scope, and future of quantitative and computer methods in mine planning and development.

Jan 1, 1979

By M. J. Scoble

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1997

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991

By Brian Flintoff

Basic process control is an integral part of most mineral processing plants. It is widely acknowledged to have helped many operations reduce costs and increase productivity and performance. The research community is very active in the development and evaluation of both model based and Al techniques for advanced control applications. Vendors and specialist consulting or engineering firms are in business to help deliver these solutions to the plant floor. It would seem that there is a good balance between business needs and technology, and that the industry should be moving steadily forward in an aggressive pursuit of plant-wide automation. However on closer examination one sees some systemic problems which are sewing to inhibit progress. One of the mist obvious manifestations is the gap which exists between the available technology and current This paper explores the control of mineral processing systems, with a particular emphasis on some of these problem areas.

Jan 1, 1995