Search Documents

By C. Haycocks

In spite of the increasingly high capital investment required for longwall mining equipment, there continues to be a steady trend towards this form of mining. This move is caused in large part by improved productivity of longwall mining systems combined with greater percentage of coal recovered over room and pillar mining, reduced manpower requirements, and the inherent safety of the system. Longwall mining is most amenable to the greater depths experienced by many mining operations, particularly in the coalfields of the Eastern United States. Two primary problems in the installation of a longwall panel are determining whether a particular seam is suitable for longwall and, secondly, type and capacity of equipment required for such a mining operation. In addition, recent legislation has forced an evaluation of the surface effects of longwall mining with a view to determining what, if any, surface damage might result from extracting any particular panel. These factors must be determined using large and often complex quantities of geological, structural, mining, and surface data. This makes the problem most attractive to solution using the computer.

Jan 1, 1979

By H. E. M. N. Moursy, M. N. Ahmad, C. R. Holland, G. M. Walker, R. D. Chandler

This work describes the effect of process parameters on the acidulation of Moroccan phosphate rock using nitric acid, i.e., the nitro-phosphate process. A series of bench scale experiments were conducted, using a stirred tank reactor (STR) system, to investigate the chemical reactions involved and optimum conditions for the formation of nitro-phosphate fertilizer. The effect of reaction time, temperature, mixing speed, acidulation ratio, and acid concentration were investigated, and were found to have an effect on the dissolution of P2O5 from the phosphate rock, using nitric acid. An increase in nitric acid concentration resulted in an increase in P2O5 dissolution, however, the dissolution was also found to be a function of acidulation ratio. A nitric acid phosphate rock ratio of 4:l ensured 90% dissolution for nitric acid concentration > 30%.

Jan 1, 2002

By Cathleen J. Webb, Arden D. Davis

Begun in 1992, an abandoned and inactive mine inventory in the Black Hills National Forest has resulted in a hazard ranking of the most severely affected sites. For purposes of the inventory, the Black Hills were divided into three main regions: the northern Black Hills, with primarily gold mines; the central Black Hills, with pegmatite mines and some gold mines; and the southern Black Hills, with primarily uranium mines. A computerized data base has been developed along with standard forms for field crews. The forms were designed to provide maximum compatibility with other abandoned mine inventories on various federal and state lands. Measures recommended for the most hazardous and heavily affected sites include regrading of unstable slopes, fencing of open shafts, and remediation of the most severe acidic mine drainage problems. Specific examples are illustrated where remediation and safety measures were recommended or have been implemented. The vast majority of the sites, however, needed little or no remedial action.

Jan 1, 1995

By A. F. Alsobrook

Specialty silica materials, as defined in this chapter, are rocks that consist predominantly of silica (SiO2) and are produced as chunks, round pebbles, and sawed or trimmed blocks and other shapes for nonconstruction applications. The rock types include quartzite, sandstone, novaculite, flint, chert, and vein quartz. Other terms used commercially include jasper, silex, lascas, and rock crystal. In its publication, Minerals Yearbook, the US Bureau of Mines (USBM) reports the production and consumption of some specialty silica materials under several headings. Quartzite, sandstone, and novaculite used in abrasive applications are addressed by the USBM under Abrasive Materials. Lascas, a type of vein quartz used in growing synthetic quartz crystals and in fusing applications, is discussed under Quartz Crystal. Silica gravel used in manufacturing silicon metal and ferrosilicon, as metallurgical fluxstone, and as a filtration medium is covered under Industrial Sand and Gravel. Information on

Jan 1, 1994

By M. Gaft, G. Panczer, R. Reisfeld, L. Nagli

Laser-induced luminescence and breakdown spectroscopy methods appear to be a good tool for real-time evaluation of dolomite content on moving belt. The distinctive feature for time- resolved luminescence is Dy3+ emission in apatite, which is excited by 251 nm laser light and detected with delay time of 5 ms and gate width of 1 ms. The distinctive features for breakdown spectroscopy are 604 nm line of F and P in apatite and 518 nm line of Mg in dolomite. The representative sampling of more than 200 pebbles has been studied by both methods. By luminescence method 100% of dolomite will be identified, while approximately 15-20% of apatite with extremely week Dy3+ luminescence may be mistakenly counted as dolomite. By breakdown spectroscopy the identification is 100% correct both for dolomite and for apatite.

Jan 1, 2002

By James L. Crowe

Electric-power-generating plants fired by fossil fuels are faced with increasingly stringent requirements for control of sulfur emissions. Several approaches for limiting these emissions, or for operating such facilities in an environmentally acceptable manner, are being pursued. Some of the approaches are based on the use of naturally occurring carbonate rocks or of materials derived from them. This paper discusses primarily the carbonate-rock-based processes being developed for control of sulfur dioxide emissions from fossil-fueled electric-power-generating plants. It includes a discussion of the role of carbonate rock materials in removal of sulfur dioxide from stack gases after combustion, capture of gaseous SO2 during the combustion process, and removal of sulfur from fuel prior to complete combustion. Materials derived from carbon- ate rocks are generally used in processes which convert the sulfur to a throwaway product, but there are also proposed processes in which the sulfur is converted to a useful product and the absorbent is regenerated for reuse.

Jan 1, 1974

By J. A. Procarione, M. K. McCarter, Bradley C. Paul

A numerical technique is described which can be used to model the quantity and distribution of air flow through broken rock. The method can also describe gas concentration and temperature distribution. A computer code implementing the numerical approach was developed to assist in determining the feasibility of a proposed modified in-situ leaching method for extracting copper from sulfide porphyry deposits. This mining method requires air to be forced through cells of rubblized ore. The flow serves to supply oxygen for the leaching reactions and to dissipate heat that would other-wise build due to the exothermic reactions. The method substitutes the Carman equation into the Laplace equation. The solution of the resulting non-linear formulation is done on a finite difference grid using SOR with iteration improvement of coefficients. This procedure yields the required air flow pattern and pressure drop. An equation for advection with absorption is then solved over the same grid using explicit schemes to yield oxygen concentration. Finally, a similar technique is applied to the convective heat transfer formula to yield the temperature profile. The model is potentially applicable to such mining problems as the prediction of leakage through caved ground, the prediction of methane concentration in gobbed ground, and the prediction of heat build-up in caved workings.

Jan 1, 1989

By M. Canty

This paper presents results from pilot-scale and field testing of an innovative technology that uses sulfate-reducing bacteria (SRB) to treat and control acid mine drainage (AMD). Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides. The bicarbonate produced serves to help neutralize the drainage. Pilot-scale metal-removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium and 96% for copper. However, the iron and arsenic removals were not as effective as the aforementioned metals. This was largely attributed to high levels of iron and arsenic that contaminating the organic substrate. There was evidence that both adsorption and sulfate reduction were occurring within the reactors. The SRB field demonstration involved using the flooded subsurface mine workings of the Lilly/Orphan Boy Mine near Elliston, MT, as an "in situ biological reactor." In the mine, high removal efficiencies were observed for aluminum, cadmium, copper and zinc (70% to near 100%) during the four years of monitoring. However, for reasons similar to the pilot scale testing, low removal efficiencies were observed for arsenic and iron. Sulfate reduction was evident by measured decreases in sulfate and the detection of soluble sulfide within the mine water.

Jan 1, 2000

By B. Tönjes

In the course of the last decade, the concept of sustainability has turned from a catchword into a vision - a vision to which politics and industry feel increasingly committed. In terms of the energy industry, the key criteria for sustainable development are supply security, economic efficiency and social responsibility. Coal is able to meet all these criteria if it is produced in conformity with high safety standards through the use of modern mining technology and converted into electricity with the aid of environmentally friendly methods. Among the fossil energy resources, coal will, according to the vast majority of global energy scenarios, continue to be the most important input energy in power generation for the foreseeable future. Coal is therefore today, and will in future continue to be, an important element in ensuring sustainable energy and raw material supply, worldwide, in Europe and also in Germany.

Jan 1, 2005

By D. A. Dahlstrom

Energy costs have had a serious impact on all basic industries today. This is due to the significant amount of energy that is used to convert natural resources into usable products. Other factors such as transportation with its major energy requirement and materials employed in processing that have already required significant energy input for their manufacture accordingly influence delivered cost to the user. The farmer is a good example of this. While his large capital investment for land, machines, and buildings is highly impacted by today's interest rates, his chemical fertilizer, herbicides, and pesticides as well as those same machines and transportation costs for his products have also been seriously affected by energy costs. With the many unit operations involved in mining and mineral processing, several of which require significant inputs of energy, one can only conclude that this industry has experienced a great increase in percentage of total cost for energy alone. Fuerstenau (1975) indicated that the minerals industry used about 12.5% of the total energy produced in the US. McNulty (1983) listed the total energy requirements for the production of 0.9 t (1 st) of various metals including the energy consumed in the manufacture of supplies employed, such as tires, explosives, chemicals, grinding media, etc. (Table 1).

Jan 1, 1987

By M. G. Ayat

In the previous work (1,2), initial developments in a novel tracing technique employing specifically prepared trace particiles were fully described. The synthetic tracers produced proved to represent coal particles in specific gravity based coal washing equipment in this work, a detection system has been developed that can detect the artificial tracers in the product or refuse part of the density-separating coal cleaning units and thus indicate the performance characteristics of the circuit. This system could not only be a simple, accurate, and inexpensive replacement for the usual time-consuming washability analysis, but it could also be used for diagnostic purposes in coal separatory devices.

Jan 1, 1987

By K. Irmscher

During the last years, using modular computer models on the software and distributed computer capacities on the hardware side has become quite common in the mining industry. When tackling real mining problems under the condition of heterogeneous systems, however, some problems become obvious: the incompatibility of the heterogeneous platforms in connection with the heterogeneously structured information and the necessity of interpreting the data. Knowledge based approaches are employed for solving different planning problems in the field of mining industry. The main problems here consist in the knowledge representation and data acquisition. Starting point of the investigation form classifications of mining planning problems and the corresponding models which can be transformed into information models for evaluation. With help of an expert system a practical solution is represented. Distributed systems with mobile computing and communication facilities for immediate access can be used as an additional support for planning and processing. On the base of public or private computer networks (including mobile networks) the foundation is given for a computer supported treatment of planning tasks. Additionally the use of teleworking scenarios in regions of mine planning and data collection in geological applications is prepared. Foundation forms a workflow system on an object-oriented distributed platform.

Jan 1, 1996

By Sharad Mathur

The purpose of this paper is to present the benefits of high reactivity meta kaolin (HRM) in high performance cement-based systems. HRM, unlike other pozzolans, is manufactured from selected naturally occurring kaolin ore and carefully processed under stringent conditions to result in a consistent product with highly pozzolanic properties. HRM is an ultrafine pozzolan that enhances the mechanical properties (workability and strength) and chemical stability (durability) of Portland cement concrete and cement-based products. HRM is unique with respect to its white color which makes it an ideal choice for architectural applications where visual and aesthetic concerns are critical.

Jan 1, 2003

By Eric Forssberg, Benny Andreasson

The paper describes experiments to stabilize mineral processing waste materials for use in construction. Fine mineral processing wastes from various mines have been mixed with binders and compacted. As binders blast furnace slag and other materials have been used. Experiments have been made in laboratory scale and in large scale. The results have been evaluated by means of determinations of compression strength and the modulus of elasticity. The paper also describes some experiments in laboratory and large scale to use stabilized mineral processing wastes for back filling in cut and fill mining.

Jan 1, 1992

By Jeffrey M. Listak, Gregory J. Chekan

The U.S. Bureau of Mines, in an effort to improve coal conservation and utilization is currently investigating longwall panel layouts to maximize coal recovery and minimize interactive problems in multiple-seam operations. When longwalling coalbeds in descending order, the transfer of stress from overlying gate roads is a major design constraint affecting pillar stability in the lower mine. The lower mine gate road pillars must be properly designed to withstand the additional load transfer if gate roads are superpositioned in successive seams. The Bureau's MULSIM/NL model was used to analyze load transfer mechanics for superpositioned gate road pillars. Analysis of Longwall Pillar Stability (ALPS), which is an empirically based design method for longwall gate road pillars, was used to calibrate model input parameters. The attributes of both the MULSIM/NL model and ALPS were combined to develop a modified method for estimating pillar stress for multiple-seam cases. The modified method uses a multiple-seam (MS) factor to estimate the stress on the lower mine gate road pillars when superpositioning is practiced. Numerical analysis shows that the MS factor is dependent upon the interburden thickness and pillar width and is presented in a series of graphs relating these two parameters. Several examples are included to illustrate the use of the MS factor for estimating lower mine pillar stress and resulting stability factors.

Jan 1, 1992

By David Caiden, Petros Fortsakis, Alan Hodgkinson

"1. INTRODUCTIONDo contractual practices affect project outcome? Can better contractual practices improve the likelihood of project success? The consensus amongst experts is that better contractual practices really do improve project outcomes. With this in mind the members of the International Tunnelling Association (ITA) Working Group 3 on Contractual Practices (WG3) pooled their collective knowledge to publish in 2011 the document entitled The ITA Contractual Framework Checklist for Subsurface Construction Contracts (ITA Working Group 3, 2011). Written for projects involving significant subsurface works, e.g. tunnels and caverns, the ITA Framework Checklist explains the major contractual issues that must be considered to ensure a successful project. Its goal is not to specify how each issue should be resolved, but rather to highlight the issues and give recommendations on how they should be addressed. The Checklist is compatible with, and provides guidance for reviewing, standard contracts such as FIDIC and NEC. One of the authors is a co-author of the Checklist and has contributed to previous papers describing the Checklist and its applicability to hydropower projects (Hodgkinson & Wilson 2014, Hodgkinson & Wilson 2015). The Checklist identifies a series of issues that should be contractually defined, which can be summarized as follows: •,Methods for dealing with geotechnical uncertainties should be defined in the contract •,There should be an appropriate level of geotechnical/geological investigation •,Sufficient mobilization periods should be allowed •,Sufficient time should be allowed for testing and commissioning •,Procedures for timely dispute resolution should clearly defined •,Quality and performance requirements should be clearly defined and measurable •,Provision should exist for cost consequences of unforeseen circumstances •,Dispute resolution processes should be clearly defined •,Payment processes should be fair and clearly defined •,Risk should be clearly allocated and parties should be able to bear the risks they carry •,There should be a mechanism for adjusting payments according to conditions •,The risk management approach should be clearly defined •,Admeasurement or unit price approaches are recommended •,The responsibilities of each party must be clearly defined •,The consequences of non-performance should be clearly defined •,The construction programme (schedule) should be realistic."

Jan 1, 2016

By J. Michael Howard

Holes cored through the Prairie Creek lamproite volcanic complex at the Crater of Diamonds State Park by companies interested in the site's commercial diamond potential give an opportunity to redefine the size and shape of the Prairie Creek pipe. Relationships of cored rock sequences and the discovery of a previously unrecognized major rock type allow a reinterpretation of the sequence and type of intrusive activity. Trench sampling of diamondiferous rock units yielded a diamond content far below what was anticipated based on an estimate from historical records. Inadequacies of shallow bulk-testing methods for a diamondiferous pipe are examined.

Jan 1, 1999

By D. H. H. Quon, A. Ahamd, G. Pouskouleli, T. A. Wheat

An outline of the contributions of hydro- metallurgical techniques such as sol-gel processing, direct precipitation and hydro- thermal decamposition for the development of high-quality ceramics is given and examples drawn from recent work on both structural (engineering) and functional (electrical) ceramics are discussed.

Jan 1, 1990

By Ralph H. Knode, Stephen P. Collings

INTRODUCTION The Crow Butte uranium deposit is located in northwest Nebraska near the town of Crawford (Figure 1). The deposit was discovered during the fall of 1980 by Wyoming Fuel Company, operator of the Crow Butte Joint Venture. The Crow Butte Joint Venture is owned 50 percent by Wyoming Fuel Company, a subsidiary of KN Energy, Inc.; formerly Kansas-Nebraska Natural Gas Company, Inc., 40 percent by Ferret Exploration Company, Inc., and 10 percent by First Exploration Company. A preliminary announcement made in January 1981 indicated a "probable potential" reserve in excess of 25,000, 000 pounds U303. Drilling during 1981 and 1982 confirmed these reserves and indicated the presence of more than 30,000,000 pounds U308 having an average grade in excess of 0.25 percent U308. Wyoming Fuel Company was initially attracted to the area in 1978 by favorable regional geology for sandstone uranium deposits and weak radioactivity noted in regional oil and gas holes. Exploration drilling began in 1979 following the formation of the Crow 3utte Joint Venture. Drilling has continued up to the present, at which time the Joint Venture is ready to proceed with a pilot scale solution mine. Environmental baseline data have been acquired and the permit applications for the pilot scale mine have been submitted to the Nuclear Regulatory Commission and to the applicable state agencies in Nebraska.

Jan 1, 1984

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another issue is how they compare to the peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1998