Search Documents

By Cyril Heever

ROCKS outcropping in Elandsrand's lease area consist of quartzite, shale and lava of the Pretoria group and are underlain first by 1 300 metres of dolomite and then by the Black Reef series. This in turn rests unconformably on Ventersdorp and Witwatersrand rocks and truncates the basal member of the Ventersdorp Super group, the Ventersdorp Contact Reef (VCR), near the northern boundary of the lease. The Ventersdorp Super group is composed of lava and varies in thickness from nil in the north of the lease area to 1 000 metres in the south. The VCR, less than 100 cm thick, dips 210 to the south east and lies between 1 786 and 3 386 metres below datum. The Oberholzer dyke straddles the north-western corner of the property and separates the dewatered Oberholzer compartment, over which most of Elandsrand lies, from the as yet undewatered Turffontein compartment. As so much of the lease area is covered by thick impermeable rocks, the water-bearing capacity of the underlying dolomite was expected to be low. The man-material (MM) and rock hoisting ventilation (RU) shafts were sited well within and above a gravimetrically determined 200-metre 'safe-limit' contour of the northern slope of the Gatsrand. Two pre-cementstion holes were drilled and the cementation rigs were placed within a 15 metre annulus round each shaft to seal any likely water-bearing pockets in the proximity of the excavation during sinking through the first 300 metres of shales and the surface water-table.

Jan 1, 1981

By RETC2023

RETC2023

Jun 13, 2023

By Charles E. Barker

Striking similarities exist between the sediment features and facies formed in some modern heliothermal lakes and the characteristics of some ancient borate depositional environments. Heliothermal lakes are density-stratified with shallow submerged margins surrounding areally restricted deep pool(s) containing a dense brine overlain by a much less dense brine. The reflective brine interface allows solar energy to be trapped in the dense brine which may warn to over 900C. carbonate precipitated from the dense brine is the typical sediment produced in warm deep pool. The strong density stratification reduces turbulence in the lake so clastic sediment is deposited under most of the lake as finely-stratified mudstone-limestone couplets (varves). This depositional process results in clastic lake sediment interfingering with and enclosing a thick evaporite pod(s). Because deep pools can exist at the same time or through geologic time, the evaporite pod(s) may occur sporadically throughout the lacustrine beds.

Jan 1, 1988

By Roland W. Rammler

In recent years, the crude oil reserves of the world have increased at the same rate as the consumption. A Consideration of the global figures suggests that adequate supplies of petroleum will be available during the next decades. On the other hand, it in a fast of economic and political significance that the reserves in the industrialized countries increase much more slowly than in the developing countries. In Western Europe the reserves have even decreased. At the present time, about 70 % of the petroleum reserves of the world are in the Middle East and in Africa in regions in which political arises are prevalent or impending. For the industrialized countries, the discrepancies between the consumption and reserves in various regions of the world are a strong urge to investigate whether oil can be recovered from other sources. The situation will probably not be changed to a large extent by the discovery of oil in the north of Alaska. The main starting materials for the production of synthetic crude oil are coal, oil shale and tar sand. In North America, where the consumption of petroleum increases more rapidly than the reserves, there are enormous deposits of each of the three materials. This fact is another incentive toward the utilization of these unconventional oil reserves, which provide a reliable basis for a supple of energy for a long time to come.

Jan 1, 1970

By Markus Thewes, Mario Galli

"INTRODUCTIONProject-related studies showed that lab tests are a helpful tool for the planning of EPB tunneling and soil conditioning in cohesionless soils. This type of ground commonly represents the extended application range for EPB shields, which demands for a treatment with additives. Considering soil conditioning with foam, so far, approaches exist for the investigation of the foam quality and of the conditioning behavior of soils (e.g. (EFNARC GUIDELINES 2001 2003)), but not any standards for testing procedures related to soil conditioning. State-of-the-art research on the topic is and was conducted for example in Bochum (Germany) cf. (Budach 2012; Maidl 1995), in Lyon (France) cf. (Quebaud et al. 1998), in Oxford and Cambridge (Great Britain) cf. (Borghi 2006; Peña Duarte 2007), in Delft (Netherlands) cf. (Bezuijen and Schaminée 2001), in Turin (Italy) cf. (Borio 2010; Peila et al. 2013; Vinai 2006), and in Aachen (Germany) cf. (Vennekötter 2012). Additionally, applied science is reported by the tunneling practice and suppliers of conditioning agents. Although the research focus in all these and further studies varied, similar test methods and test series were applied. A standardization of essential properties and testing methods (setup and procedures) however did not take place. The results from laboratory testing can only function as index values for practice because in the studies, production and application of the conditioning agents mainly takes place under atmospheric conditions. Nevertheless, the tests enable basic understanding of feasibility as well as processes and interactions going on during soil conditioning. For recommendations for standardized and reproducible testing see (Budach 2012; Budach and Thewes 2015).The most extensive investigations on the flow behavior of soil-foam mixtures have been performed by using the slump test from concrete engineering, cf. (DIN EN 12350-2 2009-08), which originally is applied on evaluating the workability of fresh concrete. Although this test does not describe the actual flow behavior, it rather represents an index on the workability, very much experience exists with this test method. Besides others, the workability – or flow behavior – of the EPB support medium certainly is a major factor of influence on the properties of the material in the excavation chamber and thus, for effective tunneling with EPB shields, cf. (Galli and Thewes 2014). For a summary of various investigations on the workability of conditioned soils using the slump test and resulting recommended slump ranges see (Budach 2012; Vinai 2006). Thereof, slumps between 10 and 20 cm have been reported as suitable workability for EPB applications. However, there is actually not much known about the real flow behavior of soil-foam mixtures related to rheological properties such as the viscosity (?) or potential yield stresses (t0). These physical values are necessary for a realistic determination of face pressure, for the design of required torques, and for an evaluation of the material flow at different locations in the excavation chamber, in the screw conveyor or on the conveyor belt. To generate a linear pressure distribution at the tunnel face, as it is assumed a priori, a low-viscosity fluid is favorable, whereas in the screw conveyor, a high-viscous fluid is needed for a controlled pressure decrease. On the conveyor belt, yield stress plays an important role preventing deliquescence and spilling from the belt. Attempts in characterizing the actual flowing of soil-foam mixtures have so far only been made by few researchers, the application of rheometry is rare."

Jan 1, 2016

By Gerry Norton

The overall economics of a coal production unit are governed by a number of interdependent parameters which individually and collectively affect the final result. A business judgement is measured through return on investment considerations and in this respect, a sensitivity analysis proves useful. Figures 1 and 2 show how the various parameters affect return on investment through unfavourable change from planned or expected values. In the case of metallurgical coals, the selling price negotiated is the primary and most sensitive variable, followed by transportation, clean coal yield and capital funds invested in mining. It is clear that coal preparation plant capital and operating costs are the least sensitive to R.O.I. For energy coals, the selling price is determined by heat energy content (x cents per million BTU's) and is therefore not con¬sidered as an interdependent variable. In this case, transportation cost is the major primary factor affecting the level of income. Again the amount of saleable clean coal or total yield has a major effect on return on investment. Most of the factors considered in Figures 1 and 2 are fixed and unfavorable change from planned values becomes critical but clean coal yield is to a great extent controllable during actual operations. Once the theoretical yield for a particular coal has been determined, the optimum return is achieved by approaching this theoretical yield as nearly as possible in practical commercial operation.

Jan 1, 1975

By B. Hagemeyer

The trend to higher solids paper coating and to neutral/alkaline papermaking is causing an above average growth in the use of calcium carbonate as both a paper coating and a paper filling pigment. These developments are expected to continue well into the 1990s. Thus, calcium carbonate will account for a somewhat larger percentage of total paper pigment volume. Nevertheless, overall growth in paper tonnage coupled with an increase in filler pigment percentages will create a demand for larger quantities of other pigments as well. Kaolin will continue to be the dominant paper pigment by far, with continued growth though at a somewhat slower rate than calcium carbonate.

Jan 1, 1986

The leaching of gold and silver by ammonium thiosulfate solutions in the presence of copper has been actively studied in recent years. Newmont Gold Company has successfully tested the ammonium thiosulfate for gold extraction following biooxidation pretreatment of low grade refractory carbonaceous/sulfidic ores. In this paper, the chemistry of the copper catalyzed leaching process is reviewed. Factors affecting both the leaching reactions and the stability of the lixiviants are reviewed and discussed from a solution chemistry perspective.

Jan 1, 1996

By Jon C. Jenkins

In order to plan the most efficient mine installation, a company should take advantage of all available information and tools. One of the first factors of a coal reserve that needs to be determined as accurately as possible is the quality of coal the mine will have access to during the life of the installation. With the aid of many types of well logs and computor analysis, we are investigating several methods of log correlation to determine such data as moisture, ash, sulphur, and BTU on an in place basis. It may be possible to determine this data more accurately in this manner than by using diamond drill cores for analysis and thus allow for a more profitable mine installation. The production of an underground mine is based on many factors, two of these being roof control and line water, where present either in the roof or coal seam. Using many of the same logs obtained from reserve and active mine areas, we have attempted to determine roof and floor characteristics such as strength, lithology, and moisture properties. Using data obtained from this program, we will make comments on possible length of bolt to be used, possible mining width, and pillar size as they would pertain to these reserves and active mine areas.

Jan 1, 1969

By James A. Commins

Accurate engineering predictions of energy needs for pollution control equipment used in surface mining operations is critically important to sound management selection of control alternatives. This paper will describe a procedure for evaluating two control alternatives with different energy needs. Three steps are involved: an analysis of the pertinent regulations, a determination of the size distribution of the particles being emitted, a calculation of the energy needs and costs of the candidate control systems as a function of these regulations and emission characteristics. The principal air pollutant to be controlled in surface mining operations is particulates, or dust, some of which is already on the material introduced into the primary crusher and other dust which is generated by the various steps in the subsequent processes. The requirement for control stems both from regulations concerning workers at the operating site, and the community surrounding the operations. In order to speak quantitatively about the need for control we will use regulations that pertain in Pennsylvania although it must be borne in mind that such regulations vary according to juristiction.

Jan 1, 1975

By E. T. Pecina

Bioleaching is a viable option for the processing of auriargentiferous refractory ores with high arsenic content. The application of mesophilic (A. ferrooxidans and ?L. ferrooxidans?) and thermophilic bacteria of the genus Sulfolobus (S. solfataricus and S. acidocaldarius) as oxidant treatment before the cyanidation of an industrial arsenical pyrite concentrate is presented. The results show that extraction of gold and silver increases due to bio-oxidation caused by mesophilic bacteria and results in a maximum gold recovery of 68%. In all strains studied, biooxidation resulted in an average silver recovery of 50%. The results showed that all evaluated strains were sensitive to solids content (5 to 20%) and average particle size (75 and 38 µm) of the concentrate.

Jan 1, 2010

By Felicia F. Peng

Using a fuzzy logic controller, a signal applied on the processes may be generated through a linguistic protocol expressing an operator's intuitive control strategies. In this work, fuzzy logic controller and PID controller imposed upon the feedback liquid level control systems for a stirred tank are studied and compared. The construction factors including the shape of membership functions, number of fuzzy variables, number of inputs, number of rules, and different defuzzification methods are considered in design and formulating the fuzzy logic control strategies and algorithms. From the analysis of the strategies and control performances, an optimum controller may be generated by making use of the best combination of these fuzzy construction factors.

Jan 1, 1997

By Raj K. Rajamani

In ball milling the rates of breakage vary primarily with the size distribution of powder in the mill. In wet grinding viscosity of the slurry varies continually as size distribution changes and hence the breakage rates change. In this study a simpler estimation scheme is used to determine breakage rates in batch grinding. Using an approximate solution to the batch grinding equation, acceleration and deceleration of breakage rates of all individual size classes is determined when the grinding environment is varied. Experimental results with limestone and copper ore show time-dependent breakage rates under both dry and wet grinding conditions. In general the breakage rates increase for coarse sizes and decrease for fine sizes with increase in the fines present in the mill. Such variations have strong implications in closed-circuit grinding.

Jan 1, 1991

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1982

By D. Diggins

Experimental apparatus for the determination of powder wettability is described. The principle of the technique is based on the measurement of the equilibrium capillary pressure in a packed bed of particles. Both the macroscopic solid-solution-vapour contact angle, e, and the specific surface area, A(m2g-1), of the powder, can be obtained. Experiments on angular quartz particles have been performed. A wide range of situations have been covered: hydrophobic and hydrophobic particles wetted with water, a variety of organic liquids and solutions of surfactants. The results show that reliable and reproducible values for 0 and A for angular and relatively coarse powders can be obtained with the proposed equipment for advancing liquid fronts in the absence of soluble surfactants. In the latter case and for receding liquid fronts in general, only qualitative trends have been obtained.

Jan 1, 1992

By Wenbing Guo, Mingjie Guo, Hebing Zhang

As resources are depleted in coal mines, isolated support pillars are often mined. Cemented paste backfill has been used to provide support during the mining of these pillars due to its safe and green mining characteristics. However, traditional cemented paste backfill mining has some shortcomings, such as poor adaptability to geological structure, leakage of paste during filling, imperfect roof-contact in partially backfilled areas, and insufficient roof strata support before the backfill reaches its design strength. This paper presents the results of a case study where L-shaped interval cemented paste backfill technology has been safely used to mine an isolated coal panel beneath existing surface structures. This backfilling method has the advantages of preventing paste leakage, improving the backfilled ratio, reducing surface subsidence, and strongly adapting to geological structure. During this field application, the setting pressure of the backfill shield reached 20 MPa, the compressive strength of the backfilling body reached 2.0 MPa, and the backfilled ratio reached 93.7%. Observational ground monitoring showed that roof-to-floor convergence in adjacent roadways ranged from 132 to 167 mm. No obvious fractures or separations in the overlying strata were observed by a borescope. The maximum surface subsidence was 342 mm, the subsidence factor was 0.136, and the damage to surface buildings was within Grade I (slight damage). This case study clearly demonstrates that the L-shaped interval cemented paste backfill method can be safely used to mine the isolated coal panel beneath surface buildings.

Jul 1, 2023

By E. G. Loesche

Grinding mills in which the comminution takes place between rollers and the surface of a disc, table or ring are generally known as roller type mills. The Loesche Mill, also known as the Disc Roll Mill, is a special type of roller mill in which the grinding surfaces consist of two rollers assembled over a horizontal disc or table which rotates at a relatively low speed. This design is particularly applicable to industry's present day demand for large capacity grinding mills.

Jan 1, 1964

By H. Colijn

Weight may be defined as the gravitational attraction or earthpull on a body (mass). Thus, from a practical viewpoint, a scale or other form of weighing device is a mans for determining mss. Weighing devices fall into two principal categories: (1) gravimetric; and (2) non-gravimetric or nuclear devices. At present, after many centuries of use, the effect of gravitational force as a meas¬ure of mass in industry and commerce remains by far the most common method for mass (weight) determination. Non-gravimetric methods are just becoming established in the industry. The general trend is toward weighing materials on the Trove. The predominant advantage of continous weighing over batch weighing operations is its ability to handle large tonnages without interrupting the material flow. The accuracy and reliability ability of continuous weighing equipment have improved greatly over the past decade. However, static weighing equipment still outsells continuous weighing equipment, because it is considered more accurate. Batch weighing can also produce a continuous weighed delivery through automation where the process requires it. In caparison with continuous weighing devices, such as belt scales, the batch-type scales have same inherent advantages affecting their accuracy. For example, weighing 300 lbs. per minute on a belt scale may mean that only 3 lbs. will be on the scale mechanism at one time. In order to obtain a scale accuracy of 1/2%, the sensitivity must be at least 1/2% of 3 lbs. or 1/4 oz. On the other hand, a batch scale may discharge a 300 lbs. load every 60 seconds through a timing mechanism. An accuracy of 1/2% can be easily obtained with a sensitivity of 1/2% of 300 lbs. or 24-oz.

Jan 1, 1970

By Joe B. Rosenbaum

Waste solutions from sea water desalination processes are enriched in minerals by a factor of two or three. This suggests that extraction of selected mineral components from the concentrated brine might help pay desalination costs. The possible recovery of gold has received particular mention. Sonstadt, in 1872, reported the gold content of sea water as 65,000 micrograms per cubic meter, or 65,000 parts per trillion. At $35 an ounce, this is equivalent to $0.065 per ton of sea water. Fritz Haber, however, after his abortive venture to restore Post War I Germany to economic health by recovering gold from the sea, concluded the gold content was 4 micrograms per cubic meter. Haber's analysis is equivalent to 0.0004 cent per ton. In the past 10 years, investigators using advanced analytical techniques reported from 4 to 27 micrograms per cubic meter. Our brief experiments to determine a threshhold value for the gold in sea water employed solvent extraction for initial concentration, evaporation of the gold-loaded organic for further concentration, and atomic absorption analysis of the gold in the concentrated organic. Radioactive gold was used as a tracer for monitoring the gold through the concentration and analytical steps. Our method established that sea water contains about 11 parts gold per trillion parts sea water, or 0.001 cent worth per ton. This agrees closely with results of recent studies by other investigators employing ion exchange resins and neutron activation techniques.

Jan 1, 1969

By Dave D. Ferris

Today the coal industry is beginning to use some very fundamental economic evaluations to determine the most economical circuit to produce a specified saleable product. The fundamental economic methods used are standard return on investment and net present value calculations. By utilizing these economical evaluations, one can justify a larger capital expenditure and realize more return for an investment over the life of a coal property.

Jan 1, 1983