Search Documents

By R. L. Lewis

The White Pine Mine is the second largest active underground copper mine in the United States, covering an area of approximately 34 km2 in the Upper Peninsula of Michigan. A numerical flow model of the White Pine Mine was constructed to evaluate engineering controls that would reduce the rate of mine water discharge after closure. Of the passive controls evaluated, the placement of low-flow bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35 percent.

Jan 1, 1996

By D. Elroi

This paper addresses the sharing of 2D and 3D data between GIS and mine planning software. Two-dimensional (2D) data, and now three-dimensional (3D) data as well, can be formatted such that both types of software can use, exchange, and display the same datasets. This increases the ability to share data between such groups as environmental, exploration, and mine planning. It overcomes shortcomings of mine planning software in areas of open database connectivity, spatial analysis, and data input and output. It also helps to overcome shortcomings of GIS software in the areas of geologic modeling, three-dimensional interpolation, and visualization.

Jan 1, 1998

By Steven F. Hoerger

Newmont Gold Company is the largest producer of gold in North America. Accurate resource estimates are critical to planning the mining in a year of over 90,000,000 t (100,000,000 tons) of mill, leach and waste grade material, from which over 47 t (1,500,000 oz) of gold are recovered. Resource estimates are updated frequently to take advantage of new drilling, improved geologic understanding and additional production reconciliations. At Newmont Gold, indicator kriging is the primary method being used to create resource estimates. Indicator kriging (IK) is a well accepted method of resource estimation; however, many details of the IK process which are critical to producing a useful resource estimate have not been well documented. An IK model must have several characteristics in order to be a useful resource estimate: the model must take into account geologic features of the mineralization; model creation cannot require too .much time; the model must accurately reflect the effects of selective mining; the model must be stored in an easily accessible format; and the model must be useable with a variety of cutoff grades. This paper will show how Newmont Gold implements the IK process in order to achieve these goals.

Jan 1, 1992

By Sharanappa Yalal, Rakesh Kumar Khali

"Himalayan geology poses the most challenging ground conditions almost anywhere in the world, one of the reasons thereof is their evolution as the youngest mountain chains. They are demonstratively rising faster than any mountain elsewhere. The composition is also younger, and consequently less well consolidated than the other older fold belts. This is consistent with the fact that they constitute one of the most active of the plate margin zones rising at a rate that is almost double the Andes, which is in turn three times that of the Alps. Thus, stress conditions (Magnitude and variations) can potentially be more extreme and adverse on a Himalayan tunneling project. Tunnel excavation under the Himalayan Mountains will pose significantly more challenges than an equal length and equal cover drive almost anywhere in the world. These in-depth-tunneling difficulties through high mountainous terrains have posed major challenges for application of traditional drill and blast (D&B) and NATM methods. Handling such adverse geology at any depth is always problematic and generally leads, if not adequately foreseen, to the significant tunneling delays. The author wants to highlight the challenges faced and on the spot solutions adopted while executing most prestigious 273Km long Udhampur –Srinagar- Baramula Rail Link Project (USBRL) in the Himalayas in the state of Jammu & Kashmir, India. The main focus of the paper is on main stretch of USBRL Project i.e. T-80 (India’s 2nd longest railway tunnel & 3rd longest in Asia) where the team of the author has recently completed a 11.2 Km long tunnel and where the train track has gone operational from Qazigund to Banihal. The construction of this stretch posed several challenges akin to highly adverse geological conditions. Executing on -the -spot solutions, the project has been completed successfully. 1.0 INTRODUCTION Construction of Udhampur-Srinagar-Baramulla Broad gauge railway line is one of the Mega projects undertaken by Indian Railways to establish a dependable transportation in the state of Jammu and Kashmir. In engineering terminology, it is a challenging project negotiating breakthroughs against the complex Himalayan geology. The Project which has been operational over last 12 years , stretch by stretch, is in advance stage of construction . The purpose of the prestigious project is to connect the Kashmir valley to the mainland of the state of the country. On the date owing to the hurdles of the tuff terrain, the transport of this part is totally dependent on the surface transport, i.e., through a road which connects NH-1A from Delhi to Srinagar. The altitude of the region varies from 500.00 to 1700.00, ranging through Udhampur to Katra - Reasi –Sangaldan- Banihal-Quazikund-Ananthnag-Srinagar-and Baramulla. The main features of this project are its Pirpanjal Tunnel and T-48 & 49 tunnels which cover the maximum length of tunneling through thick hostile geological conditions, the total length being 138km. Details of Pirpanjal tunnels are shown in Figure-1."

Jan 1, 2016

By Carl D. Wood

Traditionally, when one considers the optimization of a flotation circuit, the scope of work focuses on a review of unit process equipment. This usually includes topics such as grinding ball typed, grind size, classifier efficiency, mill liner design, chemical reagent addition rates, alternative chemical reagents, on-line process analysis, and automated control strategy. However, since very few companies can afford the capital expenditure needed to completely automate the processes, the flotation operator remains as a critical link in optimization of the circuit. Therefore, upgrading of operator skills and knowledge through training must be considered as equally as important as unit process review. This paper will review some concepts and approaches to innovative operator training. INTRODUCTION Consider for a moment the fantastic changes that have occurred in process automation at many flotation plants during the last several years. Flowmeters, density gages, and on-stream analyzers now routinely measure process conditions and effect control strategy. These functions had until recently been entrusted to human flotation operators. Now with a little stretching of the imagination it is possible to envision a plant where very little human intervention would be required. However, when one begins to calculate the capital cost required to fully install automatic equipment, it quickly becomes apparent that many parts of flotation plants will continue to require skilled, knowledgeable operators to ensure successful operation. Additionally as these automatic systems are put into place, the operator's duties become increasingly complex. Therefore no flotation plant can be considered optimized without upgrading each operator's skill and knowledge to match the technology utilized. BACKGROUND At Henderson, one of the hardest steps towards the optimization of operators was to realize that present level of operator skill and knowledge was not sufficient. Since Henderson had a track record of producing the highest quality molybdenum concentrate in the world, it was difficult to accept the idea that change was needed, or even possible. This realization came about as Henderson began a program to modernize the cleaner plant circuit. Henderson utilizes a complex cleaner flotation circuit involving multiple stages of flotation, with a counter- current routing of flotation tailings. Since start-up in 1976 Henderson had relied upon next-day laboratory analysis techniques, that provided an after the fact measurement of process. Hour to hour process control was implemented by the operator, the basis for the operators' control decisions was primarily the individual operator's experience and "feel'. Bench marking of current flotation technology indicated that on-stream analysis was a proven state-of-the-art method for improving process control. An Outokumpu Courier 30 analyzer was purchased and installed to provide real-time analysis of critical cleaner plant flows. The analyzer quickly began to provide valuable assay information, allowing the metallurgists to develop specific target values for important flotation variables. However due to the complexity of the circuit, the analyzer information showed that a problem was usually caused when several targeted parameters went out of range simultaneously. This made it difficult for the operator to determine just where to implement the proper corrective action. It became apparent that to take full advantage of the new analyzer information each operator would have to become proficient at understanding the material balance of the entire circuit. TRAINING PLAN CONCEPTS With the goal of giving each operator a working knowledge of a circuit material balance the following concepts were applied to develop a training plan: - Most operators were high school graduates, but had fairly weak mathematical skills, and had very little experience at metallurgical calculations. - The training would have to address a wide range of topics from basic fundamentals to complex material balance. The basic sequence decided upon, was to present a fundamental topic to the entire group, break into small groups to work a “hands on'”case study example of that topic, and design the case study results so that they could be combined to highlight a major portion of the material balance concept.

Jan 1, 1993

By James R. Aggson, Verne E. Hooker

GENERAL CONSIDERATIONS The design of a mine or any underground opening in rock is similar to the design of any other structure, such as a building or a bridge, in one important way. This similarity lies in the fact that the stability of the structure is a function of the loads that will be applied during the structure's expected lifetime. In the case of an underground opening, the applied load is the product of the existing in situ stress field and the concentration of this field that is produced by the extraction of a load¬bearing material. Thus, a knowledge of the in situ stress field is considered a basic requirement in the design process and essential to the eventual stability of the underground structure (Duvall, 1976; Obert, 1972; Merrill and Peterson, 1961; Dahl and von Schonfeldt, 1976; Hedley and Wilson, 1975). The in situ stress field can be used along with the physical properties of the rock masses involved, the ge¬ometry of the various rock types, the geometry of the openings involved, and a failure criterion to evaluate structural stability of a planned mine by theoretical or numerical techniques. This same information can be used to investigate ground control problems in existing mines. In situ rock stress determinations can be separated into three categories: the determination of applied stress, also called the absolute or field stress; the deter¬mination of concentrations of the field stress near open¬ ings; and the determination of changes in rock stress as load-bearing material is removed. The applied stress field is more difficult to determine than are stress changes. Various instruments and techniques have been developed to determine applied rock stress and stress changes in rock. ABSOLUTE OR FIELD STRESSES Theoretical Considerations In the absence of actual measurements, it is often assumed that at any point, the vertical stress is equal to the weight of the overlying material. [ ] where S„ is vertical stress, S is average weight density of overburden rock, and h is depth from the surface. This is normally consistent with actual experience. The horizontal stresses are assumed to be equal and related to the vertical stress through the Poisson effect. [] where Sh is horizontal stress, S„ is vertical stress, and v is Poisson's ratio. The derivation of Eq. 2 is dependent on lateral con¬finement of the rock mass. An increasing amount of information is rapidly becoming available which indi¬cates that the in situ stress field at a particular location cannot simply be assumed to be a gravity-induced stress distribution in which the secondary principal stresses in the horizontal plane are due to confinement and Pois¬son's effect. Rather they can be a complex function of gravity loading, regional stresses, structural features, ex¬cavation geometries, and variations in surface and/or possibly basement rock topography. Furthermore, the underground principal stress dis¬tribution is not necessarily vertical and horizontal as is often assumed. The deviation of the three-dimensional stress distribution from vertical and horizontal can be due to a combination of both topographic (Hooker, Bickel, and Aggson, 1972) and structural features.

Jan 1, 1982

By R. Bruce Thorndycraft

Heap leaching should not be chosen for development of a property solely on the basis of paper studies. Management should be made to understand where the risks are in heap leaching, and management should be alerted to the variability of costs in heap leaching, many of which are based upon company philosophy. These concepts are complex, but easily illustrated with guided tours of existing heap leach facilities.

Jan 1, 1998

By Tyler A. Dawson, Ryan P. Butler, Timothy Gualandri, Jason R. Edberg

"In the early 1920’s, the City of Tulsa, Oklahoma constructed an approximately 8,238-foot long tunnel, the Tiawah Tunnel, through bedrock. Voids behind the concrete tunnel liner were detected via probe drilling in early 2000 as part of an interior visual condition assessment. In 2012 and 2015, conditions along the entire tunnel were efficiently assessed through geophysical investigation using ground penetrating radar (GPR) along the inner tunnel crown and at various select locations within the tunnel. Fifty-seven (57) potential voids, extending up to 19 inches in depth and 12 feet in width, were detected with 1,000 MHz GPR and confirmed through probe drilling with approximately 80% accuracy. GPR proved to be an efficient and reliable technology for void detection behind concrete tunnel lining. This paper highlights the geophysical investigation and how geophysical efforts were combined with other investigation efforts to definitively determine the presence of voids outside of the tunnel lining.INTRODUCTION The city of Tulsa, Oklahoma has a population of about 400,000 people. The original source of water for the city was the Arkansas River. The first pumping operation provided untreated water to homes and businesses in 1904. The residents of Tulsa found this water to be unacceptable due to the high levels of salt and gypsum present. As the city grew, land and storage/treatment facilities were acquired in order to obtain and distribute a more suitable raw water. The raw water needs for the city are currently satisfied by transport and treatment of about 100 million gallons per day (MGD) of water from surface water sources. Water is transported many miles from Spavinaw/Eucha and Oologah lakes to Yahola Lake and the Lynn Lane Reservoir (totaling over 3-billion gallon capacity). From here, the raw water is treated and transported to the various customers (City of Tulsa 2015). The Tulsa Metropolitan Utility Authority (TMUA) is responsible for the operation and maintenance of the raw water transport system."

Jan 1, 2016

By P. Oghazi

It is possible to have traceability in the mining industry, by parameters and signatures like particle mineralogy, mineral association, texture and mineral liberation. The study is on an apatite-iron ore deposit at Malmberget, Sweden, and characterizes an ore body both mineralogically and texturally in a quantitative manner by using analytical methods like optical microscopy, microprobe (EMPA) and an automatic SEM based system, Particle Texture Analysis (PTA). The mineralogy was evaluated by PTA and characterized by modal mineralogy, mineral liberation and mineral associations. Magnetite has a simple outline and straight grain boundaries and the gangue minerals have a finer particle size with a more complicated texture. The PTA analysis also shows that apatite is associated to magnetite as mixed particles, while smaller grains of magnetite are inclusions in feldspar. Result from particle texture analysis shows that there is a connection which link to the mine-to-mill context, and it may be used to create traceability. This link is not the associations of the main ore mineral magnetite, nor the modal mineralogy. Instead, it is the mineral associations of contaminating minerals (apatite and feldspar) that appear to be most promising since they survive from mine to mill. The modal mineralogy may be used to understand how contaminated minerals break into or out of particles size fraction during grinding.

Jan 1, 2010

By William J. Douglas

Defining Productivity Productivity is a principal concern to all organizations - industrial, commercial, government, and academic. As a ratio of output to input, productivity measures the efficiency of an industrial process, much as thermodynamic efficiency measures the useful work obtained from the available energy consumed. However, there is one important difference. Whereas thermodynamic efficiency is a dimensionless a ratio of energies, productivity output and input are usually measured in different physical units. Nevertheless, the resulting ratio is a normalized expression for unit of output per unit of input to the process. In the early days of coal, mining was essentially a hand loading operation. There was little expenditure of alternative forms of energy within the process. Loading required expenditures of human energy on the order of 1.2 MJ/t (1,000 Btu per st). And if we accept the conventional value "you load 16 tons," the output to input ratio is 14.5 t (16 st) per manshift. In energy terms, it is on the order of 116 MJ/t (100,000 Btu per st) produced per labor Btu expended. However, the latter measure of efficiency was not meaningful in economic terms, while the 14.5 t (16 st) per manshift was significant. Since labor was the principal component of cost, it represented a direct relationship to the cost of production: [ ] Furthermore, when workers were paid directly on the basis of tons produced, the labor cost per ton was specified directly by this rate. With the introduction of mechanized loading, significant increases in productivity occurred, when measured on the basis of tons per manshift. Electric power consumed about 11.6-116 MJ/t (10,000-100,000 Btu per st). This makes the 29-GJ/t (25 million Btu per st) coal output/input ratio between 100 and 1,000. That is one or two orders of magnitude lower than hand loading. However, electric energy was quite inexpensive compared to labor, which made the mechanization economically efficient. The accepted productivity measure continued to be tons per manshift. This measure includes some of the effects of mechanization: namely, the additional manpower needed to maintain the machines and support the equipment that uses electrical energy. However, it does not consider the capital and operating costs that relate to mechanized equipment. As a result, the concept of tons per machine-shift has emerged as an accepted measure of shift productivity. The only appropriate measure that encorporates the productivity of men and machines is an economic one. The output is the tonnage per shift and the impact is the cost per shift. [ ] This is simply the inverse of the cost per ton. In addition, much flexibility is available in allo¬cating costs to the three categories. This adds a level of intangibility to the measure. The amount of information needed to obtain all of the required costs is appreciable compared to the simple matter of counting tons and workers. Furthermore, financial information relating to production costs is closely held by mining companies, so historical statistics on economic productivity are not publicly available. To extend the concept further, consider the value of the tonnage produced, to obtain a dimensionless ($/$) measure of economic productivity.

Jan 11, 1983

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

The 71st Annual Meeting of the Minnesota Section of SME and the 59th Annual University of Minnesota Mining Symposium were held jointly April 14-16, 1998, in Duluth, MN. Registration was estimated at 450 people, about the same as last year's attendance. A short course on mine productivity and a trade show that included about 75 exhibitors were also held in conjunction with the SME meeting. This year's theme was "Iron ore and integrated steel - where are we going?" Although generally optimistic in the near term, the general feeling among the attendees is that the industry faces serious competitive challenges. The iron mining industry in Minnesota experienced a tremendous rebound from the devastating downturn of the 1980s. Today, however, all seven of Minnesota's taconite plants are operating at full capacity. And these high production levels are expected to continue during the next several years. Longer-term, however, Minnesota's producers face an increasingly competitive worldwide market, including stiff competition from Canadian operations. Because of the increasing competition, industry representatives in Minnesota believe that it is critical to strengthen their operations. To accomplish this, companies are looking to: ? Further reduce production costs. ? Bring new technologies into their operations. ? Develop value-added facilities such as direct-reduced iron. ? Expand their markets. The industry is also seeking more collaboration between industry and government. The National Steel Pellet Co. and Minntac are looking at using ported kilns, which would reduce energy consumption significantly. Cleveland Cliffs, EVTAC, Northshore Mining and Minnesota Iron and Steel are all looking at building value-added plants. One such project that received attention among the attendees was Minnesota Iron and Steel's proposed $1.2 billion combined mine, taconite plant, direct reduced iron facility and steel production facility. If the operation is built, it would produce about 3.4 Mt/a (3.39 million ltpy) of direct-reduced iron pellets. Financing is pending. An announcement is expected in the fall of 1998. The pellets, containing 70% iron, would be processed into steel in electric arc furnaces. The steel produced would then be processed into hot-rolled coil, which is used by the appliance and automobile industries. The keynote addresses and technical sessions focused on these issues as well as on environmental issues.

Jan 1, 1998

By Samuel W. Woods

The Tacoma, Washington plant is one of six plants in the United States Gypsum Company's Acoustical and Mineral Fiber Division. The Tacoma facility was acquired in 1959 along with six other mineral wool plants from the American Rock Wool Company. Originally, the Tacoma plant was built as a carbide plant during the Second World War and after that was converted and operated as a mineral wool plant by several insulation companies. Through these early years, the use of raw materials at Tacoma consisted primarily of slags along with small percentages and various combinations of silica (in various forms such as gravel), limestone and basalt. These raw materials were melted in cupolas using coke as the heat source. Raw material usage and types as well as mineral wool production methods and equipment remained without major changes for many years.

Jan 1, 1983

By John T. Langstaff

Rock bursts in the deep metal mines of the Coeur d’Alene district present an ever increasing problem in the safe and economic mining of the district’s silver, lead and zinc ores. Hecla Mining Company operates two mines in the district - the Star, a 1100-ton/day lead-zinc mine, and the Lucky Friday, a 750-ton/day silver- lead mine. Rock burst problems at both operations prompted Hecla management to make an all-out attempt to find a practical method of predicting and eventually controlling these bursts. Research by personnel from the Denver Research Center of the Bureau of Mines at ASARCO's Galena Mine indicated that a recognizable pattern of seismic activity preceded some bursts and this activity could be precisely monitored by present- day, off-the-shelf electronic devices. Using information gained by the Bureau and other sources, Hecla designed and installed a 24,- channel seismic monitoring system in the Lucky Friday mine. Installation was completed in December 1973 and after a year of successful operation, it was decided that a similar system would be installed in the Star mine. This second installation was completed in June 1975. Both systems are now operating and providing continuous information on underground seismic activity. Each monitoring system consists of a network of geophones with attendant amplifiers that are connected by shielded cable through an interfacing device to a computer. The origin of each seismic event is determined by the computer and a three-dimensional location is printed out. This information is plotted daily and is used to pinpoint rock burst prone areas and chart their relative seismic activity. This paper will review the causes and effects of rock bursts in the Coeur d'Alene district, the equipment and operation of the microseismic system at the Star and Lucky Friday mines, and the results obtained to date.

Jan 1, 1977

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery/throughput target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer -plant management system in the concentrator. The overall philosophy of keeping the implementation simple but not simpler was used.

Jan 1, 1989

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about 1 m (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1987

By Kenneth K. Humphreys

Over the past four years, the Coal Research Bureau of West Virginia University has presented a number of papers on operations research in the coal industry before various AIME meetings and meetings of other societies. These papers have been followed up by further presentations in the technical press. The emphasis of all of these papers has been to demonstrate applications of operations research to the solution of numerous types of coal industry problems. In each case, effort has been made to demonstrate that operations research does not require extensive knowledge of computer science or use of sophisticated higher mathematics. In fact, for most applications, satisfactory results can be obtained by a single individual in a minimum of time with no aids other than a pencil and paper and a knowledge of basic arithmetic. The most recent efforts by the Coal Research Bureau have been directed toward the continuing industry problem of optimizing the location of mining facilities. Preliminary work in this area was presented before the Central Appalachian Section of AIME and subsequently published in the May, 1972, issue of Coal Age. This initial presentation illustrated techniques for determining optimum locations of facilities based upon material transport effort under the assumption of constant cost per ton mile of haulage effort. The present paper will expand upon this earlier work and introduce economic factors. In the design of a mine or mining system, careful consideration must be given to the sites selected for each element of the system. Optimum placement of facilities is vital to minimize capital and operating cost. Thus, barring unfavorable geological conditions or other exceptional factors, facilities should be located at those points which represent the minimum cumulative cost over the life of the property. Most cost factors are independent, or essentially independent of the location of fixed facilities. Thus, for example, regardless of the location of the shaft, the direct cost to mine any given ton of coal is essentially constant. The major 1

Jan 1, 1972

By E. Stone, R. Reagan

Risk of hand injury is very real for operators carrying out conventional bolting operations with power torque tools, reaction arms and backup wrenches. Bolting operations of this type are common today in the installation and maintenance of heavy mining machinery and equipment. Newer solutions have become available that have the potential to dramatically reduce the risk of hand injuries in mining applications. MINING APPLICATIONS Within the scope of mining operations, various types of equipment are used such as tunnel boring machines, bucket wheel excavators, draglines, material handlers, screens, pumps, crushers, continuous miners and longwall systems. Design of these machines typically includes larger diameter bolts for strength and durability. Due to rugged use all machines require frequent maintenance and service which requires the use of heavy industrial bolting tools and methods. Those engaged in bolting operations include technicians working for end-users, equipment manufacturers, general contractors and others who provide services in mining operations. Most all personnel involved with these activities are engaged with use of high power bolting tools and procedures. Training is essential to raise the awareness of bolting safety and to avoid accidents. However improved bolting tools and procedures can play an even more significant role in further improving the safety of all those engaged with bolting in the mining industry. SAFETY CONCERNS Professionals working in the mining industry are constantly looking for ways to further reduce risk to health and safety. Bolting operations which are fundamental to service and maintenance of mining equipment are often overlooked as a potential area for improvement. Several areas of bolting operations offer potential for improvement in safety and avoiding accidents during equipment maintenance. This paper addresses the safety concerns associated with reaction arms and backup wrenches in conventional bolting applications (Figure 1).

Jan 1, 2019

By Faust William A.

At Gold Fields' Chimney Creek Mine, gold ore deliveries to the milling and leaching circuits will come from three separate pits. The challenges in mine scheduling are to combine tonnage flows from these distinct ore bodies to produce a minimum of 4.665 kilogram (150,000 ounces) per year while maintaining a stable workforce and constant mine equipment requirements. A secondary goal is to have the end of milling operations coincide with the completion of leaching of the oxide ore reserves. This paper discusses the techniques used to prepare the long range plan and some of the considerations and practices that will be required for the plan's accomplishment.

Jan 1, 1989