Search Documents

By Rob Robertson

The problem of fine coal slimes has been addressed in a unique way at A. T. Massey Coal?Company. Several plants have employed two-stage classifying cyclones to separate the minus 1 mm raw coal into 3 sizes. Larger cyclones make the initial cut at approximately 150 µ (100?mesh) sending the underflow to a cleaning circuit (usually spirals) while the overflow is pumped to a secondary cyclone circuit using smaller cyclones. The small cyclones make a cut at near 70 µ (200 mesh) and produce an underflow that is a des limed flotation feed. The overflow is discarded to refuse due to its high ash and superfine size which would produce a high moisture product even if suitably recovered.

Jan 1, 1998

By Robert F. Reeves, Stephens A. Avary

Introduction People, systems, methods, and organization make up maintenance productivity. Methods promote efficiency in operations, systems ensure consistency and continuity, and organization maintains direction and control. The common denominator in these techniques, though, is people. Management systems can be technically correct, but fail to work because management systems do not work by themselves - people make them work. Therefore, the foundation for mine maintenance productivity must begin with the people involved. Traditionally, the emphasis placed on mine maintenance, as opposed to production, is not proportional to the impact that maintenance has on a mining operation. The performance and productivity of mine maintenance substantially affects the operating costs, revenues, and profits of the mine. The mining industry has recently experienced a period of economic depression. While it has created financial problems in all segments of the industry, it has caused the industry to focus on the need for improved productivity. Mining companies that have made investments in productivity during this period will have a competitive edge during the recovery, and mine maintenance may be the best place to put that investment. Future lost production and maintenance cost problems can be avoided if mine management has the foresight to seize the opportunities that now exist. Background Technological improvements over the last 30 years have been dramatic in the industry. Before these changes, mining equipment was not very sophisticated. So maintenance needs were not very sophisticated. Maintenance people were not required to have any formal training in mechanical or electrical skills. At many mines there was no formal maintenance organization. The mechanic was a part of the section crew and received direction from the face boss. Mine maintenance was not a function, it was a task. Technological change in mining came about in response to an expanding economy and greater demand for mined products. The past 20 years brought about a change in the kind of individual needed to mine ore and coal, and an even greater change in the person needed to maintain equipment. Equipment went from mechanical and pneumatic to complicated electrical and hydraulic. Maintenance progressed from being a task to being a function. Types of Mechanics Mine maintenance workers can be grouped into three categories based on experience: mechanics with more than 20 years, five- to 10-years, and less then five years. These groupings have influenced mine maintenance productivity. The 20-plus mechanic has been the foundation of the maintenance force. He had no formal training and his skills were acquired on the job. As new equipment was introduced, he learned to repair it by trial and error. Not all of what he learned was correct. Personal initiative and conscientiousness are characteristics of this group. They have experienced the bad times and the good, and appreciate the opportunity to work. The five- to 10-year group worked with the older, more experienced mechanics to acquire maintenance skills. These mechanics came in during industry boom times, and many progressed quickly by being in the right place at the right time. Many in this group have difficulty with diagnostic trouble-shooting, and depend on changing out parts to identify problems. This group is generally more mobile and less apt to have a strong work ethic. Mechanics with about five years experience have vocational training, some formal education or basic skills training. Like the five- to 10-year group, these miners are mobile and tend to move readily to satisfy their changing needs. These two younger groups are less apt to feel any loyalty to the employer or obligation to be productive. Their attitudes and abilities reflect the influence of their general age groups, and has a definite impact on mining productivity. Past Requirements In the 1960s, the basic requirements for a maintenance supervisor was that he be a top mechanic, get along well with the men, and be a hustler and improviser. He learned the details of new equipment as repairs were needed. Oftentimes, this individual would be the only person on the property with the ability to read prints, use diagnostic testing equipment, and troubleshoot using an analytical approach. This approach to maintenance is sufficient when the equipment design is reasonably uncomplicated. Management Changes As technology progressed, organized labor gained strength, government regulation increased, and the job of supervising and managing people had to change. The environment has changed and

Jan 11, 1983

By D. Marsh

The feasibility study for the Grasberg Block Cave mine, finalized in May 2008, indicated a production capacity of 160,000 tonnes per day. A rail haulage system was an integral part of the mine design. This paper describes the simulation process used in optimizing the design and discusses the key factors and variables that impact the capacity of the system. The final recommendations for the haulage level layout and associated equipment are also included.

Jan 1, 2010

By Robert J. Gorney

This paper deals with the actual application of a direct digital control to simple as well as complex industrial process control loops, Fundamental descriptions of preliminary research and design are described briefly, as is the development of the present day controller and control computer. The results and effects of direct digital control in various types of single and cascaded loops as opposed to the use of conventional controls are discussed. Computer supervision of a process and control override are taken into account, in addition to methods of short and long term plant economic optimization.

Jan 1, 1965

By Chris D. Breeds

Northwest Boring, Inc. (NWB) deployed a skinned up AVN 2000AB Microtunnel Boring Machine (MTBM) to install 7.5-foot long, 118-inch outer diameter reinforced concrete pipe (RCP) sections along an alignment between the Fremont (FRS) jacking shaft and the 3rd Avenue (3RS) receiving shaft for the Ship Canal Water Quality SCWQ Project. The alignment includes: a 67-foot long straight section, a 367-foot long curved section excavated along a 650-foot radius curve, followed by a 182-foot long straight section. This paper describes the project including planning and design, manufacturing, equipment installation in the 90-foot-deep FRS jacking shaft, egress through the secants and microtunnel operations required to complete the shaft and install the required casing pipes.

Dec 1, 2022

By M. L. Matt

The Pittsburgh Safety and Health Technology Center of the Mine Safety and Health Administration has developed the Mine Emergency Responsiveness Development (MERD) program to improve the reaction and response of mine personnel in mine emergency situations. The MERD program simulates problems that may be encountered in underground mine fires, underground mine explosions or surface mine accidents. Since its inception in 1982, the MERD program has been presented to MSHA, Industry, Labor and State Government Personnel. The program is extremely versatile and is easily adapted to suit various training requirements. It gives the participants the opportunity to experience some of the emotions, frustrations and successes of a mine emergency in a controlled environment without having to be involved in one. Past participants have indicated that this training has better prepared them in actual emergency situations through increased awareness and advanced preparation of plans and resources. In 1992, a Mine Simulation Laboratory, which simulates a coal mine and metal/nonmetal mine, was built to improve training for mine emergencies and prevention and fighting of mine fires. This facility has been included in the MERD Program to provide realistic and practical training for mine rescue teams and MERD participants in advanced mine emergency operations. This paper presents an overview of the MERD program.

Jan 1, 1993

When I wrote the Railroad portion of "Mining Engineering" magazines 94 Powder River Basin (PRB) Coal Article I described to you some definite destinations the Railroads had in mind. As with many destinations, the ones I wrote of turned out to be merely stops on the way to places that we have yet to reach. Somewhere along the way we discovered that making it better is a continuous process not just something that you can do in phases I, II, III, & IV. We always knew this I suspect, but perhaps not at the awareness level that exists in RR environments in 1997. The purpose of this article is to update the 94 article, which I could do very quickly. Everything I told you we were going to do in 94 is done, end of story! But in addition to making it a very short article it would not be telling you the things RR has done beyond what we were planning in 94 and for the future.

Jan 1, 1998

By B. P. Boisen

INTRODUCTION Application Measurement of rock deformation is essential to stability and behavioral monitoring of underground openings. The difficulties of obtaining adequate sample distribution, density, and orientation can frequently be overcome by the use of single and multiple position borehole extensometers. In its simplest form, a borehole extensometer consists of an instrument head, usually anchored in the collar of a borehole, and a number of in-hole anchors, each of which is fixed in place at a known distance from the collar. As rock adjacent to the borehole deforms, the component parallel to the borehole direction causes a distance change between adjacent in-hole anchors, as well as a distance change between individual anchors and the instrument head. These changes are measured by means of a mechanical link (usually wire or rod) extending to the instrument head from each anchor. The resulting data can be used to compute the distribution, magnitude, rate, and acceleration of deformation in the material intersected by the extensometer's borehole. Wire Vs. Rod Extensometers Since the early 1960s myriad varieties of borehole extensometers have become available through the combination of various special features of two basic instruments, the wire and rod versions of borehole extensometers. Recent publications have recommended shallow depth limitations for wire extensometers, and favor rod extensometers for a broad range of borehole inclinations and depths. There are three main reasons for using a deep wire system: its cost effectiveness; the fact that tremendous depth means tremendous rod weight which will cause the rod to buckle or rub against the borehole or casing wall; and users' attitude and proper understanding of how to install and apply a wire-type extensometer. Here experience plays a big role. Over the years, many have learned the hard way that untensioned rod extensometers are simple and inherently inexpensive, but limited to vertical up holes where sensitivity is not influenced by friction between the rod elements and the borehole wall or protective conduit, the inertia of the rod elements, or the direction of the movement to be measured. In deep, horizontal, or inclined holes, and in instances where compressive as well as tensile strains or displacements are anticipated, tensioned rod or wire systems are preferred. System Components Borehole extensometers are made up of at least the following five principal components: the instrument head; the collar anchor assembly; the downhole system of anchors and rods or wires; the signal cable if the head is equipped for electronic readout; and the readout apparatus, whether mechanical or electronic. These components are shown in Fig. 1. Borehole Requirements Most extensometers are designed for installation in nominal 75 to 57-mm (3.0 to 2.25-in.) diam drill holes. Either a diamond drill or a percussion drill hole is satisfactory, provided the variation in drill-hole diameter is within the tolerance of the standard anchor design. The basic system may be modified for other hole diameters by changing the dimensions of the collar anchor and downhole anchor assemblies. Some instrument heads and collar anchor assemblies require enlarged borehole collars, though usually not over 150 mm (6 in.) for a depth of 1 m (3 ft). It is desirable, although not essential, that holes be free-draining. Holes must be clean and free of debris before installation. Depth/Orientation of Extensometer Boreholes Extensometers are designed to measure axial strain components in the instrumented drill hole. As the drill hole is axially deformed, the distances between individual downhole anchors and the instrument head change, as do the distances between adjacent anchors. The distance changes measured by a multiple position borehole extensometer, for example, are reduced to functions of time, hole depth, anchor position, or other parameters of significance in terms of the structure under investigation.

Jan 1, 1982

By J. B. Gwiazda

In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the .u factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the .u of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves.

Jan 1, 1987

By D. Nebbia, R. Aliberti, F. Solesin

The launch of a Tunnel Boring Machine (TBM) is one of the most challenging activity parts of the construction of a tunnel. Challenges are coming from limited space available, learning curve, concurrence of other activities and in some cases from the geological conditions. Launching a TBM is an extraordinary and complicated operation requiring a great level of planning. The Earth Pressure Balance (EPB) TBM named “Chris” was successfully launched for the Northeast Boundary Tunnel, the largest component of the Clean Rivers Project in Washington, DC. Due to space and time constraints, the 8-meter diameter TBM was launched from a single 20-meter diameter shaft, with a 30-meter-long tail tunnel by means of umbilical connections. This paper presents the steps followed during the TBM assembly and launching to complete the excavation of the initial drive of the tunnel maintaining high level of efficiency and quality despite the space constraints. Specifically, it focuses on the methods and phases used to extract the excavated material (muck) from the TBM and from the tunnel, to supply consumables, precast rings and backfill grout. The paper presents results in terms of productivity, lesson learned and possible alternatives to be considered in similar conditions.

Jun 13, 2021

By Brad Grothen, Lok Home

The choice of TBM type is never easy, but it becomes especially challenging when faced with a hard rock tunnel with expected high water flows and pressure. Slurry Shield tunneling has a long history of being used in these conditions to minimize the risk, though this method has brought with it other risks along with cost considerations. At recent projects around the world, another method has been proven to effectively manage these project risks without utilizing Slurry Shield tunneling: Shielded, NonContinuous Pressurized (NCP)-TBM tunneling in rock with a comprehensive grouting program. In this paper, the authors will analyze the use of Shielded NCP TBMs at projects around the world as compared with slurry shield tunneling in rock under water pressure. Recommendations will be given in order to establish a clear picture of the optimal tunneling method.

Jun 13, 2021

By D. J. Dunn

Grinding balls, simple in shape, are actually sophisticated machine components, and essential elements of mineral grinding mills. Their physical properties and quality must be adequate to achieve design life and grinding mission with few failures. Consistant properties and freedom from breakage are essential. Size, mass, hardness profile, chemistry, and microstructure are important variables which should be designed, specified, controlled, and verified to achieve optimal mill performance. Failure to specify ball properties in detail or failure to obtain required ball properties and quality can cause milling productivity losses and excessive costs that could endanger a milling operations survival in the competive mineral industry.

Jan 1, 1989

By R. Mulyanto, M. Siray, A. Parhusip, F. Hartono

"PT Freeport Indonesia is preparing the Deep Mill Level Zone (DMLZ) mine to be the successor of the currently operating Deep Ore Zone (DOZ) mine. The DMLZ is block cave mine situated 500 m below the DOZ mine and approximately 1600 m depth from surface. Both of the block caving mines require draw point construction in the extraction level to extract the ore from caved area above. Learning from the experience in DOZ, the construction & maintenance of draw points in the production panels is a significant challenge in supporting consistent production.The average DOZ draw point construction duration is approximately 46 shifts per draw point. The time frame for construction is dependent on several variables; availability of the conventional forming system, material availability, and development tolerances. The repair of concrete floors and lintel sets causes production downtime. Reviewing the old DOZ draw point design, there is an opportunity to increase constructability, durability, and reliability of DMLZ draw points. This paper discusses how the DMLZ has improved draw point construction productivity and is on track to significantly reduce costs whilst increasing the quality by using the Six Sigma Improvement Method.Introduction The DMLZ Mine is part of the PT. Freeport Indonesia (PTFI) future Expansion to its underground mining complexes. It is the fourth vertical lift in the East Ertsberg Skarn System (EESS) deposit (Figure 1).Currently, it is under development phase.The DMLZ mine will be a block cave mine using an advanced undercutting method. The DMLZ extraction level will be approximately 1,600 meters below the surface on the 2570 level with column heights of roughly 500 m. The Undercut is on 2590 level, some 20 meters above the extraction level."

Jan 1, 2016

By Zong-Xian Zhang, Charlie C. Li

It has been observed that the rock debris of a strain burst event are often in the mode of tensile fracture. Seismic waves could create tensile fractures in the material nearby reflecting surfaces, such as at the boundary of the fracture zone and the rock surface of an underground space. The fractured rock could be ejected to the space when the seismic waves are powerful enough. The average ejection velocity of the ejected rock is a measure of the magnitude of a burst event. The ejection velocity is directly associated with the released energy from the seismic waves and with the strain energy stored in the rock prior to the burst. In some cases, the seismic wave induced tensile fracture and the energy conversion occur in successive moments during bursting. In this paper, tensile fracture caused by seismic waves is investigated through an 1D model. The relationship of the average ejection velocity of the ejected rock in a rockburst event is analytically established with the energy of the seismic waves and the strain energy stored in the rock.

Apr 26, 2022

By N. Teasdale

The Bousquet #2 deposit, located within the Blake River Group in the Abitibi Greenstone belt, midway between the towns of Val d'Or and Rouyn-Noranda, exhibits all of the distinguishing characteristics of volcanogenic massive sulfide (VMS) deposits. As such, the deposit can be compared with other gold-rich VMS deposits such as the world-class Home deposit in Rouyn-Noranda, Quebec, Canada and the Mount Morgan deposit near Rockhampton, Queensland, Australia.

Jan 1, 1995

By R. Gray

"Experience from Australia has identified what is referred to as non-conventional surface subsidence behaviour. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence”, and far-field horizontal movements – even occurring beyond conventional “angle of draw” limits. This paper discusses such behaviour recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900ft to the north, mining at depths of 330 – 720ft. Investigations (including a subsequent ground movement monitoring program) found a range of evidence in the vicinity suggesting that valley closure and far-field horizontal movements may have occurred resulting from the adjacent mining. The paper discusses the phenomenon of non-conventional subsidence behaviour and the Ryerson State Park case study, including an assessment of mining, geology and subsidence impacts and suggested ground behavioural mechanisms. INTRODUCTION Non-Conventional Subsidence The conventional understanding of coal mine subsidence on which most current subsidence understanding and prediction techniques are based, includes the concept of angle of draw which effectively limits the lateral extent of subsidence effects and impacts. Within this zone – above and marginally beyond the boundary of mining – downward vertical subsidence is the dominant component, together with localised horizontal movements towards the mined region, with related tilts and strains. However, more recent experience from Australia over the last two or three decades has identified what is referred to as non-conventional surface subsidence behaviour. This is found to occur in areas of irregular surface topography or variable terrain, and is characterised by phenomena such as valley closure, valley floor uplift or upsidence, and far-field horizontal movements, all of which can occur beyond the conventional angle of draw limits. NSW Department of Planning (2008) defined the conditions for both conventional and non-conventional subsidence behaviour as follows: “The conventional or general model of surface subsidence, which finds worldwide acceptance, is based on assuming the following site conditions:"

Jan 1, 2015

By B. Seymour

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, tests were conducted with a commercial poly-fiber reinforced shotcrete mix to develop a practical means of measuring shotcrete adhesion strength. Full-scale tests were conducted in a test frame equipped with concrete panels having three distinct surface roughness profiles. Adhesion test fixtures either embedded or epoxied in the shotcrete were overcored into the underlying concrete, and direct tensile tests were conducted to determine the bond strength of the shotcrete cores to the substrate after a selected shotcrete curing interval (1, 3, 7, 14, 28, or 90 days). Measured adhesion strengths typically ranged from 0.5 to 2.0 MPa depending on the curing age of the shotcrete samples. This paper presents the results of these tests, describes the portable test system components, and addresses some of the design issues encountered in the development of a rugged and reliable method for determining shotcrete adhesion strength in underground mines.

Jan 1, 2010

By P. Holman

I would like to start this paper by looking back about twenty years to see where we have been in the mining industry. We will also look forward a bit and talk about what lies ahead. Here is what has happened to the world economy since the 1970s. Economic growth was strong in the early 70s, but slipped into a recession in the middle of the decade. Then, after a fairly decent recovery recession struck again in the early 80s and since then growth has been rather sporadic. All in all, it has been a real roller coaster ride. There will continue to be plenty of ups and downs in the world economy in the future.

Jan 1, 1993

The methods used by Newmont Gold Company for deposit modeling are illustrated by examples taken from current operations and advanced projects. These methods vary depending on a number of factors, including geology, mining and processing methods, economic feasibility, and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques, and being flexible in selecting the appropriate methods.

Jan 1, 1997

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001