Search Documents

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By Robert S. Lehto

Zinc concentrates received in La Oroya zinc refinery are marmatitic in nature, contain about 11% iron and traces of other metal values, Figure 1 shows the zinc circuit. The calcine from the roasted concentrates is leached in spent zinc electrolyte. Major part of the impurities is iron which has been oxidized to its trivalent form, This is the origin of the zinc leach residue for which the ZILERET process was developed and so named. The impure liquor from the leach is sent for purification and thence to electrolysis- zinc deposits on aluminum cathodes from which: it is stripped, melted and cast into slabs Typical assays of zinc calcine and leach residue are given in Table 1. Metal values contained in the leach residue, without counting any value of iron, amount to roughly $130 per short ton.

Jan 1, 1969

By John S. Owens

The National Steel Pellet Project and the Butler Taconite Project are operated by The Hanna Mining Company in the vicinity of the towns of Keewatin and Nashwauk, on the western Mesabi Range. Production began in 1967, after seven years of exploratory and development diamond drilling and reconnaissance magnetic surveys, Previously, direct shipping hematitegoethite ores and gravity concentrates had been produced in the area from numerous open pits and several underground mines since the start of the century. Total shipments of these oxidized ores amounted to more than 200 million tons, but at the present time such reserves are nearly exhausted, and there are no mining operations in the Keewatin-Nashwauk area except at the two taconite projects. The locations of all of the present taconite operations on the Mesabi Range are shown in Figure 1, extending for a distance of about seventy miles from the Butler plant to the Dunka River area. The Butler and National plants have a combined rated capacity of 4.4 million tons of pellets. Their reserves cover a combined strike length of about eight miles on the Biwabik iron formation. All of the intervals between present taconite operations on the Mesabi are potential sources of additional magnetic taconite; in particular, exploration and economic studies have been carried out by Jones and Laughlin Steel Corporation in the Biwabik area between Aurora and Virginia, and by Pickands Mather and Company in the Hibbing area. However, west of the Henna and Butler holdings, it appears unlikely that magnetic taconite exists in commerical quantities at economic depths due to extensive oxidation of magnetite to hematite.

Jan 1, 1968

By W. J. Atkinson, E. M. Anderson

FOREWORD This paper is based on the authors' experience gained in the environmental assessment of major uranium projects in the former Department of Science and the Environment and Department of Home Affairs and Environment of the Australian Government. The authors gratefully acknowledge assistance received from colleagues within the Department of Home Affairs and Environment in the preparation of this paper. Special thanks go to Mr K.E. Thompson of the Department's Environment Division for his valuable comments and criticism. The views expressed in the paper are those of the authors alone and not the Australian Government or Dames & Moore. INTRODUCTION Uranium has been mined in Australia since 1954. A number of small scale mining and milling operations were active in the Northern Territory, in South Australia and in Queensland in the late fifties and early sixties. However, in the late sixties there was an increase in exploration activities in the expectation of an upsurge in world demand for uranium Substantial new resources were delineated in the Northern Territory, Queensland, South Australia and Western Australia. The most significant deposits were located in the Northern Territory, in what is called the Alligator Rivers Region located approximately 200 km east of Darwin. The Region is in the latitude of 13° South and thus lies within the Australian tropics (Figure 1). It consists of approximately 2.3 million hectares of natural wilderness containing much spectacular and attractive scenery. The area is noted for its abundant wildlife, particularly the waterbirds that gather on the flood-plains. Much of the vegetation is diverse and interesting. The Aboriginal population still maintains elements of the traditional way of life, and the spectacular Arnhem Land escarpment contains many of the best surviving examples of Aboriginal rock art. Numerous rich archaeological sites provide evidence of continuous human habitation for tens of thousands of years. Climatically, the Region is of the tropical monsoon type with a dry season from may to September and a "wet" from November to March. High intensity short period rainfall is characteristic, and the average annual precipitation is in the order of 1 350 mm. The monthly mean temperature ranges from 25° to 30°C throughout the year. The development of regulatory controls on uranium mining in the Alligator Rivers Region has been affected by the political status of the Northern Territory. While Australia is a federation, established as an independent self-governing country in 1901, it was not until 1978 that the Northern Territory became to any real extent self-governing. Prior to 1978, the Territory was administered through a special department of the Commonwealth (ie. the Federal Government). Under the Northern Territory (Self Government) Act 1978, administrative powers similar to those possessed by the Governments of the six founding Australian states were provided to the Territory Government. However, the Commonwealth government did not transfer to the Territory all such powers and functions, and in particular there has been, since 1978, a dual role for the Commonwealth and Territory Governments in the regulation of uranium development. Details of this role are provided later in this paper. RANGER URANIUM INQUIRY By 1973, major deposits had been discovered in the Alligator Rivers Region at Nabarlek, Ranger, Koongarra and Jabiluka. The estimated reserves and mine life expectancy of these deposits are given in Table I. Other radioactive anomalies have also been identified in the area but, as yet, they have not been delineated or evaluated. [ ] In 1974, an agreement was signed between the Commonwealth Government and Peko Mines Limited and the Electrolytic Zinc Company of Australia Limited for the joint development of the Ranger deposit. In July 1975, the Government announced a Commission of Inquiry under the provisions of the Commonwealth Environment Protection (Impact of Proposals) Act 1974, into the proposed Ranger development. The inquiry was known as the Ranger Uranium Environmental Inquiry or more commonly, the Fox Inquiry after the presiding Commissioner, Mr Justice Fox.

Jan 1, 1981

By L. C. Atkinson

A three-dimensional finite element Ground-water flow code has been developed that incorporates saturated/unsaturated, two-regime flow (i.e., both Darcian and non-Darcian) and solves for the seepage face at a surface of outflow. This code is capable of more realistically predicting ground-water inflows to an open-pit mine under the throttling effects of non-Darcian flow. The height of the seepage face on highwalls and the shape of the phreatic surface in the vicinity of the pit that it calculates can also produce more probable estimates of pore pressures for analysis of slope stability.

Jan 1, 1992

By R. H. Lesernann

Copper has held up extremely well as we have moved through the trough of the economic cycle. In the aluminum, lead and zinc industries at least half of the Western World production was unable to cover its operating costs at the prices prevailing throughout most of 1991. In copper, less than 10 percent of production ran in the red last year. Most of that was in Peru where the government has not allowed its currency to devalue at the same pace as inflation. Thus, mining company revenues in local currency terms have risen very modestly while costs have escalated tremendously. Excluding such governmentally imposed distortions, virtually every mine in the Western World ran at a profit last year. While copper producers have to be extremely happy about staying in the black through the trough of the consumption cycle, consumers have to be worried. They must be asking themselves, "If copper held at over $1.00 in a year when consumption declined, how high will prices go when demand picks up?" Consumers are accustomed to paying high prices at the peak of the cycle, but they are also accustomed to paying low prices at the trough of the cycle. What went wrong this time?

Jan 1, 1992

By E. F. Young

An integrated steel company is an industrial complex ranging from raw materials mining, through pyrometallurgical smelting and refining, and hot shaping, to product finishing and coating. Within this complex is a great variety of operations which use vast quantities of water, and a variety of water uses which can result in pollution of many different types. The industry has recognized most of its problems for some time, and has spent a great deal of money and effort in reducing and eliminating pollution. A recent survey by AISI showed that the industry has spent, within the last 15 years, two hundred forty millions of dollars on water pollution control, and has authorized spending eighty-seven millions more on this type of non¬productive facilities. While much still remains to be done, I think the record to date is one we can be proud of. In this presentation, we will attempt to outline a number of the water pollution problems encountered in an integrated steel company and to show what types of corrective action have been and are being taken, using Jones & Laughlin Steel Corporation as an example.

Jan 1, 1968

By Francis S. Kendorski

INTRODUCTION Drift design problems in caving operations are a re¬sult of the geologic factors contributing to the overall success of the system, of the engineering factors dictated by economic and technical considerations, and of ore production practices. Combining these factors, a rational underground sup¬port system of rock reinforcement, light steel channel section or welded wire fabric, and shotcrete can be de¬signed based on rock fracturing, rock load, abutment loadings, ground movement, expected repair and desired flexibility. The design concept uses the effect achieved by restraining, reinforcing, and maintaining some of the intrinsic strength of the fractured rock mass composed of interlocked blocks of intact rock and rock fractures. Three different examples of drift support design in hypo¬thetical mines using the caving system are given. Caving is a system of underground mining where ore is extracted by means of gravity after the ore body is allowed to fail by removing support from underneath. The rock mass of the ore body fractures and flows ver¬tically downward to let gravity do as much work as pos¬sible. Caving differs from many other mining systems in that blasting is used only to initiate the rock mass failure by removing the rock supporting the ore but not to break the ore itself. The initial movement of the rock mass dur¬ing failure and the consequent crushing and grinding during the continued movement serve to reduce the ore to particles of a manageable size, with only limited sec¬ondary blasting necessary. The broken ore is extracted from the bottom of the failed rock mass through funnels of some sort pre-excavated in the rock. Ore extraction must continue or the swell of the broken rock will even¬tually fill the cavity and stop further rock mass failure and movement. The excellent general discussion on block caving in the SME Mining Engineering Handbook (Julin and Tobie, 1973) adequately covers the principles and application of this type of underground mining. Many rock mechanics aspects of block caving have been covered by others (McMahon and Kendrick, 1969; Swaisgood, et al., 1972; Mahtab and Dixon, 1975; King, 1946) and will not be reviewed further. Maintaining the stability of production drifts is one of the most troublesome problems plaguing the mine manager in a caving operation. Many factors contrib¬ute to drift support problems, and identifying the causes of instability and producing a reasonable support design are two steps toward achieving stability consistent with the mine plan. This chapter sets forth a technique for the design of support systems for production drifts in caving opera¬tions. The basic support system elements employed are rock reinforcement, welded wire fabric, and shotcrete. Recognized as contributing to the design are the factors of rock load, additional load from mining activity, rock fracture characteristics, repair expected, and flexibility. It must be emphasized that the drift must first be stabilized as for a tunnel, and the additional strengthen¬ing for mining-induced loads cannot contribute to the initial premining stabilization, or the reserve of strength is used up. MINE PLANNING The efficient mine planning engineer not only must satisfy the economic, human, and environmental aspects of his task but must also consider the mechanical con¬sequences of his plan. The problems created for the mine by placing parallel drifts too close, by crossing drifts on different levels with inadequate, if any, separa¬tion, and by installing connections and crossovers in the haulage plan without regard for the effective spans cre¬ated, are only a few of the problems a mine planning engineer can create for himself and the mine. The effect on immediately adjacent mine areas when an area is caved is important to drift design because the removal of vertical support from a rock mass causes the weight of that rock mass to be shifted elsewhere. The adjacent rock mass will carry this load and reach a new equilibrium with the applied stress. The advancing front of stress increase that results from caving (and many other mining systems) is generally called the abutment load and is the increase in stress over the gravity or tec¬tonic stress that already exists, as shown in Fig. 1. In general, the abutment load will be similar in nature to the stress change found around an opening in rock and will be taken as causing an increase in the vertical prin¬cipal stress, due to an approaching caving boundary, so that

Jan 1, 1982

Surface contamination of minerals during fine grinding may occur due to coating of one material on the other. This can alter the surface chemical properties and adversely affect the separation of minerals by physico-chemical processes. In dolomite-silica system, selectivity was completely lost (compared to a synthetic mixture) after wet grinding of the minerals in spite of using a dispersant. Adsorption and surface characterization studies were conducted on silica particles separated after grinding with dolomite. SEM-EDAX analysis indicated the presence of dolomite on silica particles, which could cause the loss of selectivity.

Jan 1, 1993

By John J. Mulligan

Coal is found in every major geographic region throughout Alaska and in two offshore areas. Since about 1852 over 100 small mines have opened and closed. Last years production was almost entirely from one mine in central Alaska. Clearly the utilization of Alaska's abundant coal resources presents political, economic and technical problems that are far from solution. Location and Physical Features Figure one illustrates the geographical and geological similarity between Alaska and western United States. The Arctic region of Alaska generally resembles Wyoming and the Dakotas. The Brooks Range is an extension of the Rocky Mountains. The Central region of Alaska between the Brooks Range and the Alaska Range bears a general resemblance to the basin and range country of western United States. The Southcentral and Southeastern regions has a similar resemblance to the Sierra Nevadas and the west coast of the United States.

Jan 1, 1982

By Chuck R. McLendon

A new face ventilation system was needed at the Allied Chemical Trona mine, near Green River, Wyoming. The development of an exhaust manifold face ventilation system came from a need to reduce the dust and noise concentration level while maintaining methane control at the continuous miner working face. Dust laden air from a heading being driven by a continuous miner was contaminating the intake air in the mine around the roof bolter operator and adjacent headings. Each working heading was exhausted into the last open crosscut by a face fan. A face fan would contaminate the adjacent downstream heading with dust-laden air until a high dust concentration developed in the final entry before the returns. A face ventilation system was needed to give the exhaust of each heading an individual path to the return air. In addition, the system could not interfere with the present room and pillar mining process. A manifold system of rigid duct ventilation tubing was designed using the existing fans in a parallel arrangement. Each system was to consist of the rigid duct tubing in three headings junctioned together at the last open crosscut and exhausted at a common branch in the return air. Each heading was to have its own damper (or valve) so that air could be directed where it was most needed. The system was installed using both round and oval rigid duct ventilation tubing to minimize head loss and to allow proper ground clearance for mining machinery. Two fans in parallel were used to exhaust three headings. By adjusting the valves at each heading, up to 18.0 kcfm (9.36 cu m per sec) could be exhausted from one heading and still keep the methane level controlled in the other two headings. The manifold exhaust system has proven to be an efficient, long lasting ventilation system at the Alchem Mine. It has reduced the dust and noise exposure levels at the working faces while keeping the methane level under control.

Jan 1, 1980

By Peter K. Achireko, Samuel Frimpong

Design and optimization of open pit limits are of paramount importance because they provide information for evaluating the economic potential of a mineral deposit and for developing short and long range mine plans. Many algorithms and their modifications have been used to design and optimize open pit limits. These algorithms have provided mine planning engineers with pertinent information in designing, optimizing and extracting ore reserves by open pit technology. However, they do not address the random field properties associated with the ore grades and reserves and commodity prices, and thus, fail to yield the truly optimized pit limits in any time horizon. In this paper, a new algorithm, MCSIMFNN, which overcomes these limitations is proposed and used to optimize open pit limits. The random field properties of the ore grade and reserves have been modelled using the modified conditional simulation based on the best linear unbiased estimation and local average subdivision techniques. Artificial neural networks are used to classify the blocks into classes based on their conditioned values. The error back propagation algorithm, in the neural networks, is used to optimize the pit limits by minimizing the desired and actual outputs error in a multi- layer perceptron under the pit wall slope constraints. The optimized pit value obtained by this algorithm has been compared to that from the Lerchs-Grossman's algorithm in a case study. The results are the same, but in random multivariable states, the MCSI MFNN algorithm is the most suitable for pit optimization. The method is also fast since it mimics the operation of the brain in the solution of the pit optimization problem.

Jan 1, 1996

By Rodolfo V. de la Cruz

Abstract. The Hoskold mineral valuation method was critically examined. The original derivation was presented and found to contain a number cf erroneous assumptions as follows: the sinking fund must be available for reinvestment in another property; the series of reinvestment of the sinking fund results in a perpetual annuity to the investor, and; evaluation of the present value of the net cash flows at the speculative rate of interest. The proper procedure of deriving the Hoskhold mineral valuation formula was discussed and illustrated with a cumulative cash position diagram, a useful tool in economic evaluation and investment decision methods.

Jan 1, 1980

By Hans U. Bartholet

The bentonite industry in Europe includes both the smectite and hormite groups of clay minerals. The smectites are, essentially, a compendium of cationic differentiatable montmorillonite platelets which can be expanded in liquid media, whereas, members of the hormite group are characterized by fibrous and chain structured lattices which are non-expandable. As was pointed out in the March '78 issue of Industrial Minerals, each of the minerals in these groups has acquired a variety of names due to historic or regional usage.

Jan 1, 1979

By S. Stebbins

In 1994 Western Mine Engineering, Inc., (WME), which is now InfoMine USA, Inc., set out to build a suite of stand-alone software programs that would provide their clients the means to estimate the costs of developing and operating mineral exploitation projects. After the first program (Sherpa for Surface Mines) was completed and launched, the developer (me) left WME to form Aventurine Engineering, Inc., in order to complete the series of applications. In the years since, four programs have either been developed or upgraded and enhanced. Applications were produced that estimate the costs of underground mining, placer mining, and project site reclamation. In addition, an application specifically designed to evaluate the economics of these projects, which was based upon a program previously developed for WME by Bill Willoughby of Willoughby & Associates, was redesigned and the code updated to a MicroSoft compatible platform. All these programs follow an engineering-based approach to cost estimating. Instead of relying on rules-of-thumb and statistical averages, they calculate all of the engineering and operational parameters needed to estimate costs. The premise is that the uncertainty associated with cost estimates should lie with the data available for the resource, not the approaches used to design and estimate the associated design parameters. In other words, it is acceptable that items such as the resource grades, deposit dimensions, ore and wall rock characteristics, and mill recovery rates carry with them some uncertainty, but parameters such as loader bucket capacities, truck speeds, pump horsepowers, hoist velocities, and grinding mill diameters can be calculated (although uncertain data might be used in those calculations). No additional uncertainties should be introduced because the cost-estimating procedure relied upon statistical manipulation or anecdotal inaccuracies. To that end, the programs rely upon calculation-based approaches to selecting and sizing machinery, assigning the required workforce, and determining the extent of the consumables needed to recover mineralized material at a rate defined by the client. And while calculation-based software is not unusual, more modern approaches work toward the development, accumulation, and manipulation of data. INITIAL CONDITIONS AND PROJECT GOALS In 2016 we had five separate programs completely disconnected from one another. Each was written in VisualBasic, a language that was falling from favor. In essence, the status in 2016 was a series of stand-alone programs (Figure 1) in which results from one needed to be manually entered as input into another.

Jan 1, 2019

By D. T. McMurray

INTRODUCTION Shabanie mine, situated some 180 km east of Bula¬wayo, has been a producer of chrysotile asbestos for more than 50 years. The ore bodies occur in serpentinized dunite, which overlies talc-carbonate schist. A zone of relatively competent rock of varying thickness occurs between the schist and the ore bodies, which are gen¬erally less competent. The hanging wall of the ore bodies is economic, and the hanging-wall serpentine carries a variable subeconomic amount of fiber. It is important to note that, in general, the ore body competence is less than that of the foot and hanging-wall formations. Historical After surface operations ceased, cut-and-fill stoping was used to win ore from underground; this was success¬ful until the increasingly stoped-out area caused insta¬bility in the stope pillars and back. Consequently, dur¬ing the early 1950s, a gradual change to cave-mining methods was made, the ore being won by hand lashing in drawpoints, situated in the basement of the stope blocks, and passed through orepasses under gravity to the haulage level some 13 m below. About this time, interest was focused on the sub¬level caving method in use in Swedish iron ore mines: it was felt that it might be applied economically to the Shabanie ore bodies. Accordingly, in 1958, an experi¬mental stope block was laid out in which sublevel inter¬vals and extraction tunnel spacing were 9 m. The tun¬nels (ring drilling drives) were oriented on strike-in contrast to the Swedish system, in which crosscuts that retreat from hanging to footwall are used. The advantages of the method were quickly appre¬ciated by the operating personnel and, despite the in¬evitable teething troubles pertaining to the introduction of any new mining method, it was not long before sub¬level caving was providing a high proportion of the mill feed. The disadvantages also became apparent at an early stage, however, and, from that time to the present, continuing modifications have been made to mining lay¬outs in an effort to improve ore recovery. GENERAL DESCRIPTION OF METHOD The mine is served by a vertical hoisting shaft, in which two skips, a man cage and a service cage, provide adequate capacity for production requirements. The rock hoist is a Ward Leonard control hoist, in which two electric motors drive a common gearbox. The man winder is driven by an a-c motor. Several auxiliary shafts provide secondary egress and intake and return ventilation. Main haulage levels are above (Fig. I a and b). Blasthole fan patterns are drilled by drifters of 100 mm bore, drilling 41-mm holes; when a sufficient strike length has been drilled, a slot is cut in the upper¬most sublevel and the rings are broken into the slot. Initially, a limited tonnage is drawn, since it is essential to ensure that the hanging wall caves behind the retreat¬ing stope face. Once this has been established, maxi¬mum tonnage can be drawn, as described later in this chapter, under the heading "Draw Control." The broken rock is loaded by 0.14 and 0.20-m3 load¬ers into cocopans (rocker-dumping type of tipping truck), which are hand trammed to orepasses, discharg¬ing on the haulage where 11-t electric trolley locomo¬tives haul 3.95-m3 Granby cars to the main shaft bins. As is evident from Fig. 1, the layout is simple, the block is brought rapidly into production, there is a high degree of selectivity and flexibility, and the result is a low-cost high-productivity mining method. DEVELOPMENT Main haulages are developed at 3.2 x 3.2 m, and once the service winze connections have been completed the development of the sublevels is undertaken. The footwall drives are cut first, to obtain access to the block. These ends are of the standard section, 2.4 x 2.8 m, and from them crosscuts at intervals of 70 m are driven through the ore body to the hanging wall. These crosscuts are used to supplement the geo¬logical information previously obtained from diamond core drilling, and they provide additional and more de¬tailed data on fiber percentages and lengths, structural features, and other relevant criteria which are used to build up the geological assessment of the area and to classify it in terms of the geomechanics rock classification (Laubscher and Taylor, 1977). The crosscuts also allow the necessary orepasses to be sited conveniently so that tramming distances from the loading points are not excessive. Development Drilling Once the skeleton development has been completed, the extraction headings are developed at 2.4 x 2.4 m as shown in Fig. 1. Standard development practice is to use crews of a machine operator and his helper, equipped with air-leg mounted jackhammers, to drill rounds of 1.8 m with integral tungsten carbide tipped drill steel. The round drilled is a normal drag round, as shown in Fig. 2, but considerable attention is paid to the drilling of the perimeter holes to use effectively the

Jan 1, 1982

By John A. Breslin

The U.S. Bureau of Mines develops technology to help ensure that the Nation has an adequate and dependable. supply of minerals at reasonable economic, human, and environmental cost. Our research programs seek improvements for almost every aspect of the mineral production cycle--from evaluating the availability of minerals, removing the ore from the earth, to enhancing the performance of mineral materials. The health and safety of the men and women who work in the Nation's mines and minerals processing plants and the environmental impact of mining and mineral processing are major Bureau research concerns. In recent years, the U.S. mineral industry has found it increasingly difficult to compete for a share of world markets. Many foreign producers benefit from lower production costs and higher grade deposits. Some foreign governments subsidize their mineral industries and impose fewer restrictions with respect to environmental controls and health and safety regulations. If the United States is to compete in world mineral markets, innovative technology must be found to lower the cost of recovering and processing minerals. Mining and mineral processing research by the Bureau identifies ways to help the country maintain a sound, competitive industry and a dependable mineral supply, so vital to economic growth and the national security. This work includes efforts to improve existing techniques and procedures; but more and more of the Bureau's resources are being focused on long-term, high-risk research directed at developing new approaches to mining and mineral activities--approaches like in situ mining. Bureau scientists are studying the mining applications of computer assisted mining and investigating a variety of "high tech" approaches to extractive metallurgy. Such cutting-edge research will be necessary if major advances in health and safety, environmental quality, strategic and critical minerals availability, and overall U.S. competitiveness are to be achieved. It is just such high-risk research that the industry cannot afford to conduct itself, but--in the long run--cannot afford to be without. It is this type of research that will help us arrive at a revolutionary breakthrough rather than small incremental changes in health and safety technology as well as recovery methods. Our mining and mineral processing research is also directed at reducing the Nation's dependence on imports of minerals that have key defense and industrial uses. Some of these strategic and critical minerals are particularly vulnerable to supply disruptions. We are working on technologies that would allow the United States to take advantage of domestic sources of these minerals--sources consisting primarily of deep or low-grade ores, ores with complex mineralogy we do not yet know how to process, and small deposits that are now uneconomical to mine and process. Other research activities focus on ways to reduce the Nation"s consumption of key minerals and increase the recycling of these minerals. The opportunities in this area include coal. The current middle eastern crisis reinforces the need for a stable energy supply--preferably a domestic supply. The extensive reserves of coal in this country are well documented. Perhaps what is not as well recognized is the impact that the price of coal can have on its competitive position both for domestic fuel selection considerations as well as for the ability of this country to compete in the coal export market. Today, the role to the United States is as a reliable, but high-cost exporter of high-quality coal. U.S. export coal competes with supplies from other major suppliers, including Australia, Canada, Poland. If U.S. mining costs were lowered by at least $8 per ton in the year 2000, then coal exports would surge by a projected 46 percent, and U.S steam coal displaces significant quantities of foreign coal imports in Europe. Further cost reductions would make

Jan 1, 1991

By Gregory Witte

This paper will explore the technology behind and applications of smart motor control centers (MCCs) being used today in mineral processing facilities. The two technologies to be discussed are solid-state motor controllers that can be installed in MCCs and the complementary digital communication networks that can transmit operational parameters of the solid-state devices to the supervisory system. The toughness and reliability of solid-state technologies have led to a dramatic increase in their usage throughout the mining industry. Products such as solid-state motor protectors, controllers, and variable frequency drives have demonstrated greater flexibility and performance in a variety of applications than their electromechanical and mechanical counterparts. The three key trends apparent in the solid-state devices are: 1. A shift to smaller, smarter, more integrated devices, which allows a single solid-state device to serve the purpose of multiple electromechanical devices but in a much smaller form factor. 2. Distribution of control logic in motor control devices rather than conveyed through a hard wired connection to a central automation system. 3. Embedded network communication that allows supervisory systems to have an expanded view into critical loads and sensors. In applications, the use of smart actuators and sensors with integral local intelligence and communication allow a supervisory controller to send high level commands and let the smart device coordinate its own work The ability of smart field devices to return noncontrolled, nonpoled information opens a whole array of new capabilities for preventive maintenance and diagnostics and forms the basis for an effective motor management program. The smart motor control devices this paper will explore are the smart motor protectors (SMP), smart motor controllers (SMC), and variable frequency drives (VFD).

Jan 1, 2000

By Stewart W. Daniel

Competitive pressures involving product duality, uniformity and economics are increasing the interest in and accelerating' the adoption of automation by the cement industry. The demands of this industry on instrumentation and control manufacturers for more effective and reliable control of process variables is also increasing. The trend to replacing small grinding mills with a fewer number of larger mills is lowering the investment requirement per unit of capacity both for the mills and for their automation. Cement process control systems of today are more sophisticated than the equipment installed two or three years ago, not because the process itself is more complex but because todays demands require a higher degree of control action and accuracy. Because of increasing labor costs, an important objective of an automation program is a reduction in the process labor content. This can be realized by allowing the operator free time for other duties, by increasing the number of grinding circuits one operator can supervise and by removing to. a large extent the need for the operator to make process' adjustment decisions.

Jan 1, 1965

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the foundry, the sand was examined in detail. Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1993