Search Documents

By Joseph M. Hans

INTRODUCTION The decontamination of a uranium mill site is principally an earth moving task. The task can be completed effectively and efficiently by selecting the proper earth moving equipment and using that equipment within its particular constraints for decontamination work. A considerable backlog of experience concerning earth moving equipment selection and use was acquired during the decontamination work conducted at the former Shiprock, New Mexico, uranium mill site. This experience was acquired by trial and error while decontaminating over a wide range of depths and different types of terrain. Many different types of excavation equipment were available to the Shiprock decontamination project because the Navajo Engineering and Construction Authority (NECA) heavy equipment operator's school was doing the decontamination work and a variety of equipment was needed for training. The equipment is described and its general use for decontamination is discussed. Its on-the-job use for decontaminating the Shiprock millsite is presented. [EARTH MOVING/ANCILLARY EQUIPMENT DESCRIPTION AND DECONTAMINATION CONSTRAINTS] Tractor-Scrapers The most commonly used scraper is the bottom-dump type because it is highly mobile and can dig, carry, and spread loads. In this type a tractor is connected with a yoke to a scraper bowl (Figure 1). The bowl is essentially a rigid box that pivots around the rear axle, opening to the front. A hardened steel knife, or bit, is attached to the leading edge of the bowl. When scraping, the bit penetrates and forces the earth overlying the bit edge into the scraper bowl as the scraper moves forward. When the bowl is full, it is closed by lowering a closure or apron against the cutting bit. The load is dumped while moving, by raising the apron and forcing the load from the bowl with a crowd, or ejector. The height of the dumped load is controlled by adjusting the bit height when dumping. Scrapers of this type generally do not have enough power to scrape up loads unassisted. Loading assistance is generally provided by a crawler tractor that pushes from the rear against the scraper's push block. Some scrapers are made self-loading by adding an additional engine for the extra power needed for the load pick up. Another commonly used self-loading scraper uses a loading elevator (Figure 2). The elevator consists of two roller chains carrying crossbars. The elevator is rotated when scraping and the crossbars cut the earth above or in front of the bowl bit, forcing the load into the scraper bowl. No apron is used on elevating scrapers. The load is dumped by partially retracting the bowl floor and pushing with an ejector. Scrapers have some undesirable characteristics when used for decontamination work. One characteristic is that a clearance space exists around the apron when it is in its closed position. Part of the load (especially sandy soils) dribbles through the

Jan 1, 1981

By W. A. Crosby

The ability of open pit mines to steepen overall final wall angles allows significant cost reductions as a result of reduced waste movement requirements. Final wall angles are principally controlled by three factors: geological conditions; hydrological conditions; and wall control blasting practices. The first of these factors is not controllable by the mine operator, the second can be influenced to some degree, but the last one certainly can be controlled, hence the current interest in final wall blasting practice at many mining companies. This paper discusses common blasting techniques employed to steepen final pit walls and outlines the attractiveness of moving from small hole high cost systems to the use of full size production drills as a means of reducing wall control blast costs. Attempts to make this change have been limited at many mines by the physical size of the drills and their inability to reverse drill. In the past, pres pi it, pre-shear or trim holes have had to be drilled vertically, at considerable distance from the upper bench toe, with the result that inter-berm face stability is reduced and final wall angles have to be made somewhat more shallow than desirable. The paper concludes with a description of how these problems can be overcome by utilizing the new Bucyrus 39R which has the capability of drilling at a ?15 degree angle underneath the machine. It is concluded that the resulting wall control blast designs will offer large mines improved final wall angles with resulting significant overall cost reductions.

Jan 1, 1998

By J. Liniecki, w. Chruscielewski, T. Domanski

INTRODUCTION Mining is the Polish greatest industry employing about 350 thousand miners in more than a hundred underground mines. The mining regions are located mainly in the south of the country - see Fig. 1. [ ] The coal mining dominates, however, and the zinc-lead and copper-ore mines presently employ about 16000 miners. All these mines are rather deep and wet. Their drawing shafts are between a hundred to more then thousand meters deep. The cross-adit of working area of mines ranges from several kilometers to a few tens of kilometers. The numbers of mines per mine differ also considerably and depend on the territory and type of mines. The largest coal mines employ about ten thousand miners but the largest metal ore mines do not employ more than four thousand miners. In all the mines the electric motors or diesel engines are being used. The intensity of mine ventilation, characterized by the volume of fresh air injected in to the main ventilating shaft per miner and per unit of the power consumed by the engines is about 6 cubic meters per minute per man and per horsepower. The studies of the potential alpha energy of radon daughter products /RnDP/ could be divided into the three developmental stages: I-st - stage /1966-1970/ the stage of so called Pilot Survey. During this stage concentration of potential alpha energy of RnDP in the air was measured in selected typical mines in all mining regions of the country. II-nd - stage /1972-1974/ was the periodical control of concentration of potential alpha energy of RnDP in the air of zinc-lead and copper-ore mines which have been chosen and recognized during the first stage as being the most hazardous ones. Air-sampling system /ASS/ measurements were applied during this stage.

Jan 1, 1981

By Robert M. Anderson

A popular perception by the public and many mining claimants, is that the 1872 Mining Law provides a statutory right to mine and extract minerals from the public lands. This perception in reality, is both true and false, depending on the mining claimants' ability to meet federal and state environmental, cultural and endangered species laws. Land use decisions and proposed legislation affect exploration and development opportunities in California. It is imperative that the mining industry involve itself in the planning process to ensure that BLM decision makers are fully informed of industry's knowledge and concerns. STATUTORY RIGHTS AND ENVIRONMENTAL CONSTRAINTS "No other problem has such a sense of urgency and poses as profound consequences to the quality of life and the creation and distribution of societal wealth as how we protect the environment. Certainly, the environment is the single biggest issue facing mining and mineral activities in the new decade. David S. Brown The 1872 Mining Law was passed, ironically, the same year the nation's first National Park was established. It is a perception that the establishment of Yellowstone National Park was the beginning of the United States' earliest environmental movement; brought on, perhaps, by the rapid clearing of land for homesteading purposes and, the concern that many acres of the public domain were being disposed of through a multitude of public land laws. While there was an effort being made to designate some special and unique public lands as parks for preservation purposes, environmental concern and awareness did not lead to mandatory identification of environmental impacts and appropriate mitigation until the passage of the National Environmental Policy Act in 1970. Consequently, it is not surprising that the original United States Mining Laws of 1866, 1870 and 1872 had no mention of environmental protection. There have been numerous attempts to repeal the 1872 Mining Law over the last 50 years for a variety of reasons. Currently, there is a perception by the general public, media and even some in congress, the mining industry and BLM that a change is needed. The environmental organizations want the industry to be more accountable for reclamation and post mining uses. In Tn nEnvironmental Agenda for the Future," leaders of America's foremost environmental organizations state that the mining law "includes no protection for the environment," and therefore, should be reformed. We can all acknowledge, as stated above, that the mining law, per se, requires no "protection. However, the Bureau of Land Management (BLM) clearly has the authority and the responsibility to fully "protect" non-mineral resources while providing for the extraction and processing of mineral resources by private industry. There are about 13 major federal laws that have indirectly or directly amended the mining laws to require Environmental, Historic and Cultural Protection." There have been many mining law case decisions about the statutory and constitutional rights of miners to explore open federal lands, "stake a claimg" and extract minerals. What needs to be fully understood is how federal laws, as enumerated on Table 1, may affect these rights. What follows is a description of

Jan 1, 1991

By J. W. Leonard

Breakage, handling and treatment techniques that result in the placement of greater quantities of coal in fixed volume haulage units such as ships, railroad cars, trucks, mine cars, shuttle cars and scoops can do much to increase productivity by improving bulk density to reduce delivered cost, surprisingly enough, only in steel industry by-product coking has this subject been investigated and applied to practice, where as much as 20% or more productivity has been achieved. Research at UK Mining using popular coal mine loading cycle simulators shows that for typical Central Appalachian mining conditions a 10 to 20 percent gain in bulk density can produce a 15 to 30 percent increase in the loading cycle time of fixed volume shuttle-car/scoop based mining systems.

Jan 1, 1989

By Robert L. Vines

"What is past is prologue" - motto of National Archives The question of past, present, and future safety performance in the coal mining industry is not merely an academic one, or one which arises from soul-searching curiosity. It is a question involving pragmatic ramifications, and the answers, or perhaps the public perception of the answers, will have a strong impact on the public policies which influence the course of meeting the Nation's future energy demands. Those of us in the coal industry are keenly aware of the significant impact of the public reaction -- in the form of the 1969 Health and Safety Act -- to -past performance of the coal industry which it found unacceptable. That Act was revolutionary -- and it was expensive. But in finding the industry's past performance unacceptable, the public also recognized its own contributory role through having enjoyed a "buyer's market" forced on a highly competitive industry. One result was to limit the industry's resources and restrict its ability for self-improvement of its safety performance. In acknowledgement of that role, the public picked up the tab for Black Lung disability incurred prior to that time.

Jan 1, 1985

By L. M. Turner

Perlite is a unique mineral that upon heating expands to about twenty times its original volume. Mining is by open pit method. The processing cycle involves crushing, screening and sizing the ore. An on-site quality control facility at the Manville Products No Agua mine exerts a high degree of control over every phase of the operation from blasting to finished product.

Jan 1, 1985

By Roy Moreby

Dartbrook Coal is currently developing a modern, high production (3.5 Mtpy) single longwall retreat coal mine in the Upper Hunter Valley of NSW, Australia. The location is a green field site, with no surface or underground mining operations ever having taken place in the initial target seams. The coal seams of the working section, floor and immediate roof average a total 20 m in thickness and contain a mixed carbon dioxide 1 methane seam gas ranging from 6.5 to 11.0 m3/t. The target seams have undergone detailed characterisation to assess hazards and quantify the controls required to minimise associated risks during mining. Risks identified during initial phases of exploration and 14 months of development include: • High gas emission during development. • Probable high longwall gas emission rate. • Medium to high propensity to spontaneous combustion • Possible carbon dioxide outbursts on geological structures • The main controls currently in place include, • Mine geometry and ventilation circuits • Exploratory drilling ahead of development • Intensive in seam pre drainage • Goaf drainage plants • Comprehensive monitoring systems • Underground environmental management plan. • Pre mining predictions of gas emission provided an indication of gas emission rates which have proven to be an under estimate. Current mine issues are; • Both surface fans are at full capacity (250 m3/s 1.4 kPa) • Both gas drainage pumps are at full capacity (2.3 m3/s) • Alternatives to extensive in seam pre drainage being investigated (surface to in seam hydro fracture) Review of mine design underway This paper describes the seam characterisation, assessment of mining hazards and summary of the management plan developed to address the risks identified. A review of current mine underground environmental performance is also provided

Jan 1, 1997

By Thomas de Lange

Extensive test work performed on the Coalscan 3500 ash analyzer at the Grootegeluk Coal Mine has led to the successful implementation of on-line ash monitoring to control the quality of coking coal and power station coal. Test work results are given and the advantages of on-line bias compensation discussed. Some details of the quality control systems subsequently implemented are also highlighted. Finally, the economic benefit of on-line ash monitoring based on the Mayer curve is demonstrated.

Jan 1, 1992

By Alan J. Reed

The Afton copper-gold mine is located in the southern interior of British Columbia, 16 km (10 miles) west of Kamloops and 257 km (160 miles) northeast of Vancouver. 'An aerial view of the property in 1976 is shown in Fig. 1. The Afton copper-gold ore body [27 Mt (30 million tons)] of open pit ore with a grade of 1.0% copper, 0.46 g/t (0.01 6 oz per ton) gold, and 4.1 g/t (0.12 oz per ton) silver, occurs within the Triassic Iron Mask pluton adjacent to its faulted contact with Tertiary rocks. The geological setting of the Afton ore body is described by Carr and Reed (1976). Rocks of the Paleozoic, Mesozoic, and Cenozoic eras outcrop in the vicinity of Kamloops, but the unit with the greatest economic significance is the Upper Triassic Nicola volcanic group and its subvolcanic dioritic intrusion, the Iron Mask pluton. The Afton ore body occurs at the northwesternextremity of the Iron Mask pluton immediately south of a deep graben structure that developed in post-Triassic time (Coast Mountains orogeny) and which was the focus of vigorous sedimentation and volcansim in Tertiary times. The Iron Mask pluton is a lenticular composite intrusion approximately 14.5 km (9 miles) in length in a northwesterly direction. The petrography of the Iron Mask pluton ranges from picrite and serpentinite to latite porphyry. Outcrops of individual petrographic units are generally elongate in a northwesterly direction parallel to the axis of the pluton. The Iron Mask pluton represents the moderately slowly cooled core of an oceanic fissure volcano which built up an island flanked by shallow-water sediments including reef knolls and which, during its later stages, intruded its own volcanic pile.

Jan 1, 1991

By Guy Reed, Russell Frith

In situ or pre-mining horizontal stresses are arguably the least well understood of the principal inputs into underground coal mining geotechnical engineering design, whether analytical, empirical, or numerical. This is a direct result of both the cost and difficulty of obtaining meaningful stress measurements, the various limitations of the measurement method in terms of sourcing strata types that approximate the assumed conditions of the post-measurement mathematics to convert measured strains into stresses, and a common practice by some geotechnical professionals to preferentially utilise generic values rather than interrogate the available measurement data for cause and effect relationships between horizontal stress magnitudes, directions and a range of associated controls. That numerical modelling simulations attempt to mimic reality but often rely on simplified generic horizontal stress input assumptions is a particular cause for further consideratio The paper attempts to further explore the nature of in situ horizontal stresses using a range of stress measurement results from the Australian coal sector supplemented by several international studies addressing the same basic issue, the result being a number of credible and highly relevant “cause and effect" inter-relationships between the three principal in situ stresses in addition to the influence of rock properties (e. Young's Modulus and Poisson's Ratio), cover depth and the larger-scale structural geological environment. In particular, the paper demonstrates that despite being commonly overlooked as a primary rock/coal material property, Poisson's Ratio and the associated K Effect are intrinsic to understanding 3D in situ stress measurement results and therefore, predicting in situ stress magni- tudes more generally for geotechnical analyses purposes. As a fundamental question, the paper addresses whether it is necessary and of engineering value to characterise in situ horizontal stresses: according to distinct "domains," in the same way that more easily identifiable geotechnical properties such as rock mass ratings, coal seam thickness, ply splits, and cover depth are often treated.

Jun 25, 2024

By B. W. Madsen

Experimental results obtained from large scale (7 tons), long-term (500 days) leaching of low tenor copper sulfide ores were interpreted by a geometric model involving the movement of a reaction zone through the ore fragments. The postulated leaching mechanism involved mixed kinetics and included diffusion of the reacting species through the host rock and a chemical reaction at the surface of the mineral particles. Ore properties which were considered were ore particle size and shape, grade of ore, and mineral content. Excellent agreement between the mixed kinetic model and the laboratory leaching results was obtained when minus ½ inch ore particles were not included in the leach. Also, a satisfactory prediction of copper recovery from plus ½ inch ore with a different particle size distribution was made; however, it was necessary to modify the shape factor in the model. Predictions of copper recovery from an ore sample which included the minus ½ -inch fine fraction and leaching for 460 days was 56.5 percent, and the recovery from leaching was 47.0 percent. The presence of fines caused channeling and uneven solution distribution and inhibited the leaching rate.

Jan 1, 1974

By David Wilburn

Recycled materials are increasingly being used in road construction to supplement natural aggregate derived from crushed stone, sand, and gravel. An understanding of the amount of substitution that is taking place, its economics, and factors affecting the level of substitution is useful in estimating the potential for recycling and in assessing the total supply of aggregate. While U.S. consumption of recycled aggregates from crushed concrete is estimated to have increased 160 percent between 1994 and 1996; it comprised less than 5 percent of total aggregates consumed in 1995. Construction waste supply is regional, and is determined by infrastructure decay and replacement rates. Aggregate recycling rates are greater in urban areas where infrastructure is being replaced, natural aggregate resources are limited, disposal costs are high, or strict environmental regulations prevent disposal. Recycling is expected to increase as construction contractors attempt to save on transportation, disposal, and new material costs. Aggregate producers include recycled material as an option to consumers in order to prolong the life of their reserves and improve their range of products. Recycled aggregates can be a supplement for natural aggregates in selected applications, but their use should be evaluated locally based upon relative cost, quality, and market factors Because aggregate recycling is often affected by local and regional transportation systems, disposal and tipping fees, resource supply, the market for specific products, and municipal support, costs for three representative fixed site operations of different sizes were modeled. Under study conditions, all were found to be profitable, but highly dependent upon local tipping fees and market prices, which can differ significantly by location. Smaller operations were found to have different operational dynamics, often requiring creative marketing or incentives to maintain profitability.

Jan 1, 2001

By James N. Prudden

Measurable physical characteristics of placer deposits include geological, geomorphological, sedimentological and mineralogical features which produce the complimentary ingredients with which one can formulate an economic evaluation of these complicated deposits within the confines of a well established geological model. Heavy mineral suite composition and character will change downstream from the provenance area and will compliment the related depositional environment. Careful attention to gold particle characterization during the exploration phase can indicate new source additions, enhance deposit evaluation methods and greatly assist in maximizing metallurgical efficiencies. Failure to recognize and measure these important features very frequently leads to frustrated and unrewarding placer evaluation goals. Increased general acceptance of sedimentology in the gological appraisal of ore bodies has progressed into the science of clastic sedimentalogy using measurable parameters to evaluate minable units. This branch of geology has developed as a tool in locating, defining, and mining alluvial concentrations of valuable heavy minerals. The repeatedly successful application of this valuable tool in conjunction with other classical geological methods can be directly related to the development of a geological model which formulates the distribution of detrital gold. This use of multiple geological techniques permits the transfer of routinely derived data to management. Standardized nomenclature permits the transmission of uniform information thereby promoting credible property evaluation. This approach enables organizations to critically assess large numbers of potential mining targets for definitive feasibility studies. Sedimentology must play an integral role in the evaluation of any alluvial deposit. The sampling problems associated with particulate gold are well known and frequently cause perplexing evaluation problems. Consequently, properly directed and executed

Jan 1, 1987

By T. W. Camm

One function of the U.S. Bureau of Mines is assessing potential economic impacts of federal land withdrawal policies. This often requires performing economic ana1ysls for an area with limited geologic information available. Input to the economic decision process relies heavily on estimates of mine and mill costs for the potential resources in the area being considered. A methodology for performing these cost estimates was needed to address this situation.

Jan 1, 1992

By George J. Thompson

Almost all persons connected with mining industry have had an exasperating experience like the following: 'On a cold and frosty morning in mid-January, you find yourself quite happy with the world. Production is up and the mine has been running smoothly. All at once the radio cracks up your tranquility -- 'so and so' piece of equip¬ment has broken its 'whatzit'. Now the iron is in the fire, and things have to be fixed quick.!' This can be a major failure which will bring the whole operation to a grinding halt or just one of the numerous maintenance headaches on an auxiliary piece of equipment. After one has experienced a major or minor catastrophe, he has to wonder whether some other methods with respect to design and maintenance would help prevent these unexpected calamities. The objective of this paper is to gain an insight into the charac¬teristics of steel at cold temperatures so that better decisions can be made with respect to maintenance and repair of mining equipment. Most machinery and their structures are exposed to cold temperatures. Even in locations as far south as Alabama and Arizona, brief periods of cold in winter months can adversely affect the ability of mach¬ines to do their work. To understand the background of cold temperature brittle fracture, jet us examine its basic elements. First, when steel gets cold, it gets brittle. This is best described by Figure 1. This graph shows a typical stress/strain curve of a mild or medium grade steel at room temperature. Stress is defined simply as the amount of force acting on one square inch of

Jan 1, 1972

By Shunji Sukizaki

Recently development of cheaper and cleaner energy sources has become a more important and urgent issue, because of the soaring crude oil price and environmental problems such as global warming. In this social context, to establish basic technologies and solve fundamental issues associated with environmental impact assessments, the Environmental Impact Assessment Group of the Research Consortium for Methane Hydrate Resources (MH21 research consortium) in Japan has conducted a number of research and development activities since FY2001. These activities include: 1) surveys of the marine environment that will form the basis of environmental impact assessments associated with methane hydrate development; 2) the development of core technologies to monitor deep-sea environments; 3) research of major issues related to environmental impact assessments; and 4) the development of numerical models to predict the deformation of seafloor sediments containing methane hydrates.

Jan 1, 2008

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By G. D. Naugle, L. C. Atkinson

Introduction Deep open-pit mines invariably affect the local and regional hydrologic systems. Pit dewatering, occurring during mining operations, puts an obvious hydrologic stress on these hydrologic systems. However, post-mining hydrologic impacts resulting from the pit refilling with groundwater following the cessation of mining activity can also be significant. The prediction of the rate at which the post-mining pit will fill with groundwater is a critical aspect of assessing the long-term hydrologic impacts. Numerical groundwater flow modeling provides a method for predicting the groundwater refilling rate of the pit. The rate at which pit "lakes" fill depends on several factors: •the rate and duration of pit dewatering; •the depth and size of the ultimate pit and •the pre-mining hydrologic regime. These factors can be incorporated into a detailed numerical groundwater flow model that can then be used to assess the effects of dewatering and post-mining recovery on the local and regional hydrologic systems. A sufficiently detailed, numerical groundwater model provides the oportunity to: •account for complex geology near the pit; •assess the impact of active pit dewatering and •predict the long-term impacts of post-mining groundwater flow into the pit. A detailed groundwater model incorporating these items has been developed and applied at an operating open-pit mine. Developed by Durbin and O'Brien (1987), the three-dimensional, finite-element, groundwater flow model was used to represent the hydrologic system of an approximately 253-km2 (98-sq mile) area surrounding the pit. Historical groundwater elevation data, stream flows and meteorologic, geologic and geophysical data were used to establish the dimensions and initial conditions for the model. Steady-state conditions, representing the pre-mining local and regional hydrologic systems, were simulated using the initial conditions incorporated into the groundwater model. The groundwater model was then utilized to simulate various dewatering programs, to predict the filling rate and the groundwater depth in the ultimate pit once mining activities are complete and to assess the long-term impacts on the regional groundwater flow system. Development of pit lake model Groundwater modeling efforts were completed in two phases. The first focused on pit dewatering activities, while the second phase concentrated on the post-mining effects on the hydrologic system. The final estimates of groundwater elevations calculated during the pit dewatering simulations were used in predicting the post-mining recovery of the hydrologic system. The groundwater model was also modified prior to the second phase to account for the volume of rock removed during mining activities. To account for the actual volume of rock mined, the geometry of the post-dewatering model grid was modified to approximate the final pit geometry. The depth and width of the ultimate pit were divided into eight idealized stages that represented significant changes in the bench geometries. These eight stages were then introduced sequentially into the model according to the predicted water elevations within the pit. In this way, changes in the volume and depth of water within the pit were accounted for through time. Once the ultimate pit geometry was accounted for in the model, it was necessary to assign new hydraulic characteristics to those parts of the model grid (elements) that represented excavated rock. The solution of the numerical model requires that finite hydraulic conductivity values be assigned to the portion of the groundwater model that represents excavated rock. Therefore, the calculated groundwater elevations differ, somewhat, between the edges and the center of the open pit. These model-calculated water elevations at the edge and in the middle of the open pit represent the elevation of water that would occur in the pit lake. To minimize the error in the estimated level of water within the pit lake, the hydraulic conductivity was increased to a value that would: •minimize the predicted difference between the groundwater elevations across the open pit and •produce a numerically stable solution. Specific storage is the hydrologic parameter that accounts for the water produced by compaction of the aquifer matrix. To predict the groundwater volume that would flow into the ultimate pit, this parameter was assigned a value equivalent to the compressibility of water. This value of specific storage reflects the post-mining groundwater storage occurring as an open body of water. Additionally, a specific yield of 1.0 was assigned to the pit elements to represent the 100% porosity of the open pit. In

Jan 1, 1994

By J. C. Yingling, J. W. Leonard

Introduction The absence of coal-face particle management heavily penalizes the transportation of coal from initial loading to final consumption. The penalties include dust problems, significantly reduced mine-loading-cycle productivity, mine-belt spillage, excessively high coal-preparation costs, chute blockages and dangerous pulverizer blockages at the final point of utilization. Fine particles commonly cause environmental and economic problems. It is well known that these fines can cause safety and environmental dust problems. But it is not well understood that these fines can also swell broken coal to a point where 5% to 15% more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading-cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long-established, and frequently misleading, basis of tonnage. It is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain nonfrothing chemicals, which are added to mine-face spray water, and by employing improved mine-face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed. The precursor to the work presented in this paper, involving the bulk density improvement for broken coal and the subsequent production gains for underground coal mines, was earlier presented in Leonard and Newman (1989). In the past, this topic has been studied and practiced only in byproduct coking in the steel industry. However, a potential exists for an increase in coal-industry productivity by improving the bulk density of coal to yield a subsequent reduction in delivered cost. This can occur with breakage, handling and treatment methods resulting in the loading of greater quantities of coal in fixed volumetric capacity haulage units such as mine cars, shuttle cars and scoops. Laboratory-based experiments to achieve an increase in productivity by increasing coal bulk density were discussed in Leonard, Paradkar and Groppo (1992). Chemical techniques using small quantities of commercially available reagents (surfactants) resulted in about a 13% to 15 % increase in bulk density, which was thought to produce a proportional increase in the productivity of a mine, together with a subsequent reduction in cost. The idea is to mix the reagents with the water that is used to spray coal during mining. In this paper, the impact of bulk density improvements on production rates is presented. Increases in production ranging from 60% to 88% of the bulk density increases are projected. This analysis was performed for atypical continuous-miner section. In the following sections, discussion and results of the analysis are presented. Discussion An analysis was performed to ascertain the impact of bulk density improvements on face-production rates for a typical continuous-miner section. Figure 1 illustrates the section layout and cut sequence. This layout and sequence is identical to the case described in King and Suboleski (1991). As can be seen, the section uses five entries and 12.2-m cuts that are taken by a remotely controlled continuous miner. The seam height is 1.5 m and two shuttle cars (5.7 t nominal capacity) are employed for haulage from the miner to the section feeder, which, throughout the cut sequence, is positioned as illustrated in Fig. 1. The simulation model was coded in the SIMAN simulation language. The major impacts of increased bulk density improvements on such a production system are as follows: •Shuttle-car payloads, in terms of the mass of coal transported per haul cycle, are increased proportionally to the increase in bulk density that results from the application of surfactant. •Shuttle-car discharge times should remain largely unchanged, because they are determined by the volume of material that is discharged, rather than the mass, and this volume does not change.

Jan 1, 1996